Flashed rom now have no 3g or 2g data. Any body have any advice
I have one advice: to begin, specify what Rom did you flash and how...
Sent from my SGH-T959 using XDA App
avengethis1 said:
Flashed rom now have no 3g or 2g data. Any body have any advice
Click to expand...
Click to collapse
First off, this is the wrong forum to post in. You should delete and move to the Q&A sub-forum for a better response.
That being said, how about a little more information? What ROM did you try and flash? What ROM were you coming from? Did you make a backup before you flashed?
Every little bit of info helps.
edit: damn it, beat me to it, but i typed it so it's staying!
Ok sorry for lack of info. I flashed from bionix 1.3 to stock. I tried flashin again to no prevail. Still no data connection and can't lget into download mode for odin. Any advice
Reflash
Sent from my SGH-T959 using Tapatalk
May be useful if experiencing no data connection
Quick question,
After flashing rom, during reboot. Did your phone seem to be stuck in a boot loop? If so, did you pull the battery and do a hard reset or interrupted the reboot after flash at all?
Also, have you checked all your access point setting and ensured they are all correct?
Worse case senrio, flash back to a stock rom, then try and reflash rom again. If there was anytype of interruption during initial flashing, reflashing the same rom usually will not correct the problem.
This may not be the case for all, but it is a problem I ran into.
To get into download mode, try pulling battery. Hold down both up and down volume buttons, while still holding down volume buttons plug in USB that is connected to ur USB. Then after USB is plugged in, put ur battery back in. Remember, the entire time ur still holding down the two volume buttons.
Also, if using windows 7 with Odin, ensure you reboot windows 7 into the 'turn off digital signatures...' or whatever the name of the boot option. This can be done usually by pressing F8 in the BIOS. It is listed in the same boot menu as the safe mode option. If not Odin will usually freeze on cache.rfs(?), or whatever the name of the file.
Hope this is somewhat useful. Shoot me a message if you have any questions.
Jonathan rubcic
Electrical Engineer
Khafra
Sent from my SGH-T959 using XDA App
Thread moved to Q&A.
I've tried the apn and it's all correct. As for the Odin thing the computer sees the phone when on bit not when off with the two button combo so when I plug in the cable it goes straight to charge screen instead
under settings, and about phone, what does your Modem Baseband say?
I had an issue last night (ultimately killed my vibrant) where my Modem Baseband said "Unknown"
I was working on this:
http://forum.cyanogenmod.com/topic/7504-odin-flash-loses-your-unlockfreeze-code/
I was on JI5, phone started rebooting when trying to pull a signal. Flashed JP3, said I had a JFD Modem. ODIN w/ repart to JFD, Modem Unknown with reboots. Went to flash JI2 Modem, and forgot I had repart checked.
So, it repartitioned the phone, cleared the efs, and only flashed a modem.
Needless to say..doesn't turn on now.
Replacement will be here mid-next week.
So i was able to enter download mode from abd and used odin to flash JFD back on to the phone. Phone is working great now
Related
I have never bricked it before, and I cannot go into download mode... I tried the the Vol up and vol down, didn't work, so I have been using ADB and just ****ed something up....
Now I need to know a way how I can revert back to stock, please and thank you, I will forever owe you one.
EDIT: Okay there is some confusion, to simplify it I will take it step by step:
I replaced an APK file from my system/apps and ever since it has been force closing process.android.acore, so I tried reflashing to stock, it froze while doing so now I have a picture of a caution sign, a phone and a computer coming up on my Vibrant, it will not start up.
It is hardware locked because I have never been able to access download mode via hardware keys(I have always been using ADB).
Is there any way I can reinstall stock? Or is my vibrant now destroyed?
what exactly were you doing when your phone stopped working? "just ****ed something up" makes it hard to pinpoint problems...
I don't know I replaced my phone.apk with another one then ever since then it keeps saying process.android.acore has stopped working. It wouldn't stop showing up so I tried to reflash with Odin to stock but it froze and now it is bricked.
bumping a little bit, I have never bricked it before so I have 0 experience.
What do you mean by froze? On what screen? How far can you get into booting?
bigragu said:
What do you mean by froze? On what screen? How far can you get into booting?
Click to expand...
Click to collapse
Alright let me start over with more detail:
I tried to replace the dialer so I replaced the phone.apk and then process.android.acore kept force closing so then I tried reflashing with stock, during that I don't know what happened but I think my phone froze, so then it shut off and turned back on, I only found a screen with a computer on it... I am assuming it is bricked.... I also know it is hardware locked because I tried going into debug mode with vol up and vol down, how can I unbrick it?
Try moving the stock rom into the phones internal memory via adb. And flash it after a wipe.
I am Also having this same problem
I Flashed my Vibrant through Rom Manager to Froyo 2.2 from eugene373 and sombionix.
After flashing to both ROMS for Froyo I wanted to revert back to 2.1.
I tried to put sombionix 1.3 eclair ROM back on to my phone using clockwork mod.
The flash was not successful it stopped in the middle but the phone came on with a Force close error of an android process.
I tried to reboot through adb reboot recovery with usb debugging enabled.
The phone shut down like it would reboot into recovery mode and now it gets stuck on boot at the samsung vibrant screen.
I tried to use ODIN to flash back to the stock Rom but the phone is recognized in ODIN but will not flash.
ODIN sees the phone but will not get past flash analysis. (Sat for 8 Hours)
I believe this is the definition of bricked. Please Help!!!!!
sheek360 said:
Try moving the stock rom into the phones internal memory via adb. And flash it after a wipe.
Click to expand...
Click to collapse
It isn't even being read by my computer... nothing...
sympala said:
I Flashed my Vibrant through Rom Manager to Froyo 2.2 from eugene373 and sombionix.
After flashing to both ROMS for Froyo I wanted to revert back to 2.1.
I tried to put sombionix 1.3 eclair ROM back on to my phone using clockwork mod.
The flash was not successful it stopped in the middle but the phone came on with a Force close error of an android process.
I tried to reboot through adb reboot recovery with usb debugging enabled.
The phone shut down like it would reboot into recovery mode and now it gets stuck on boot at the samsung vibrant screen.
I tried to use ODIN to flash back to the stock Rom but the phone is recognized in ODIN but will not flash.
ODIN sees the phone but will not get past flash analysis. (Sat for 8 Hours)
I believe this is the definition of bricked. Please Help!!!!!
Click to expand...
Click to collapse
Excuse me sir, make your own thread, don't jack mine...
Smokexz said:
It isn't even being read by my computer... nothing...
Excuse me sir, make your own thread, don't jack mine...
Click to expand...
Click to collapse
lol Sorry Smokexz didn't mean to jack your thread just trying to consolidate phone bricked threads. I will create my own NO PROBLEM.
sympala said:
lol Sorry Smokexz didn't mean to jack your thread just trying to consolidate phone bricked threads. I will create my own NO PROBLEM.
Click to expand...
Click to collapse
Thanks, regardless both our situations are bad .
Please? I really need help with this.
Smokexz said:
Please? I really need help with this.
Click to expand...
Click to collapse
If there is an answer, which I am not sure that there is, it would be here: http://forum.xda-developers.com/showthread.php?t=782739. You may have already seen it, but if not it gives many different processes to try. Good luck!
hourst2 said:
If there is an answer, which I am not sure that there is, it would be here: http://forum.xda-developers.com/showthread.php?t=782739. You may have already seen it, but if not it gives many different processes to try. Good luck!
Click to expand...
Click to collapse
Yep, I'm screwed thanks for the help though.
Can you get the phone in download mode?
Did you try this:
Pull battery
hold the volume up and down
reinsert the battery whiles still holding down the volume up n down
plug in usb cord
it should put you back in to DL mode
Open ODIN and unplug phone from PC and plug back in hopefully it will notice it then.
I am not sure if you can get in DL mode and it just wont let you do anything, but if you have already tried this my apologies.
gthmcty1 said:
Can you get the phone in download mode?
Did you try this:
Pull battery
hold the volume up and down
...
Click to expand...
Click to collapse
Did you even read the OP? He is HARDWARE LOCKED ie BUTTONS DON'T WORK geeze people learn how to read!
And on topic, if you can't ADB and you are Hardware Locked, you are SOL. Try to get an exchange from T-Mobile since it appears that they regard being Hardware Locked as a defect.
Alright thanks
Sent from my Motorola_i1 using Tapatalk
gravis86 said:
Did you even read the OP? He is HARDWARE LOCKED ie BUTTONS DON'T WORK geeze people learn how to read!
And on topic, if you can't ADB and you are Hardware Locked, you are SOL. Try to get an exchange from T-Mobile since it appears that they regard being Hardware Locked as a defect.
Click to expand...
Click to collapse
Your a dumb ass, His thing actually does work.. I was "hardware locked" like 5 times That DOES work, you sir are a DUMB ASS < Had to say it again
(Make sure that your USB is plugged into your computer & not your phone)
Remove the back cover & remove the battery along with your sim & micro SD
Hold the VOL Up & VOL Down
(Keep holding those buttons) Now insert the battery
Plug the usb into your phone.
It will put you back in to DL mode
Open ODIN and unplug phone from PC and plug back in hopefully it will notice it then.
^^Do that
gravis86 said:
Did you even read the OP? He is HARDWARE LOCKED ie BUTTONS DON'T WORK geeze people learn how to read!
And on topic, if you can't ADB and you are Hardware Locked, you are SOL. Try to get an exchange from T-Mobile since it appears that they regard being Hardware Locked as a defect.
Click to expand...
Click to collapse
Wow you come in and try to offer up help and you get some one that feels the need to police the "suggestions"........ Have a coke and a smile my friend...and relax!
gthmcty1 said:
Wow you come in and try to offer up help and you get some one that feels the need to police the "suggestions"........ Have a coke and a smile my friend...and relax!
Click to expand...
Click to collapse
Not to mention that what that guy said actually works...
Some people just make me laugh
(Make sure that your USB is plugged into your computer & not your phone)
Remove the back cover & remove the battery along with your sim & micro SD
Hold the VOL Up & VOL Down
(Keep holding those buttons) Now insert the battery
Plug the usb into your phone.
It will put you back in to DL mode
Open ODIN and unplug phone from PC and plug back in hopefully it will notice it then.
^^Do that
ok so i know how to do things on my vibrant but dont really know exactly how the phone does things (basically im a directions follower) so im going to try to be as precise as possible
my phone has been rooted for a while and ive been experimenting with a bunch of roms. i decided to flash TWs nero v3 w/voodoo and i was pretty sure id stick with that for a while but some of my games started having issues so i decided to flash the newest axura. now something told me that i needed to disable voodoo first and there is usually a voodoo submenu in CW recovery but there wasnt so i figured it was disabled already
so i flashed it and everything was going well untill my screen went blank
now my phone acts like there is no battery in it
ive tried any button combinations with charger in (wall or computer) or out.
no matter what my screen stays blank...plz help
im not exactly in a situation to just buy a new phone.
Unplug the phone from the charger. take your battery out for at least 15 seconds. plug the phone to your computer via usb. while holding both vol+/-, not power, put the battery back in. you should be in download mode.
use odin to flash a stock rom.
this all should work if you have the samsung drivers installed on your comp.
Go to this link it should help http://forum.xda-developers.com/showthread.php?t=848737&highlight=bricked+phone
btw i followed what both above said and neither worked for me =/
thanx for ur suggestions though
Ive seen alot of these post lately and all were on nerov3 .
Sent from my SGH-T959 using XDA App
Well I guess that your best bet would be modifying the usb charger with resistors. as stated in the link that jewbrad suggested. A similar thing happened to my phone when I tried to go back to stock from nero, but instead of a blank screen, I got a small icon of a pc and phone with a triangle in between. The method that I posted did the trick. Maybe you should try it again and check odin to see if it recognizes your device, even if the phone might look like its off.
Sent from my SGH-T959 using XDA App
Have you tried having odin open on you pc and loaded with eugene's froyo that doesnt brick then with your phone turned off(pull the battery then put it back in) now hold the volume keys up and down at the same time then plug your usb cord that is plugged into your pc into your phone this should get you into downlod mode. If this workes flash it and let odin do its thing after its done running it will reboot and go to a recovery screen then it will try to boot up ounce you see the i9000 screen you can pull the battery again and get it back into download mode the same way you did before and then flash the stock vibrant rom tar file and pit. I dont know if this will work but it cant hurt I know how it is not having your phone working so hope this helps
Same thing happend to me.
Please let me know if you get it fixed.
I was on Nero V3 trying to reflash because GPS didn't work well.
i got in to boot loop so i tried to get back to stock and re-do it,
and this happened.
I took it tmobile and claimed the ota broke it..they sent me a new one
NVM!! link posted by jewbrad had No-Boot phone instruction, and it worked!!!
Oh lucky...I tried that n it failed
I was trying to revert my wifes phone to stock and odin would not work. I used heimdell with the wrong file. The phone now has a i9000 interface. I cant call or text because it wants a sim card which obviously is impossible. and I cant get it in download mode to put the Fascinate interface back on it. Im an idiot!
Zerokillstreet said:
I was trying to revert my wifes phone to stock and odin would not work. I used heimdell with the wrong file. The phone now has a i9000 interface. I cant call or text because it wants a sim card which obviously is impossible. and I cant get it in download mode to put the Fascinate interface back on it. Im an idiot!
Click to expand...
Click to collapse
hey,
chill, user error happens. I know your wife probably can't see that right now but....
one time I did the same thing, sorta, and bricked and couldn't get into download mode. I couldn't get the phone to do anything, not even the charging animation. that is how you know its bricked.
it sat there unplugged and without a battery or sdcard for about 20 hours lifeless. I was in the process of ordering a new phone through insurance when I decided to hold my volume button down, plugged in and it was great!
once you get to this point, and you will if your phone is turning on at all its not bricked, then you will need to follow instructions for repartition like your coming off cm7mtd using a FULL BUILD like DI14 (I have a mesmerize so I'm not positive your full builds) with repartition checked using the atlas_2.2.pit file.
if that didn't work at all for you, there is a way to force download mode, using a homemade jig. google for galaxy s download mode jig if that's your only option.
good luck, and please do let us know how it goes for you. I've never used heimdall but its pretty similar to odin from what I've seen so that would probably work as well. if you're not sure if the rom you have for heimdall is a full build, open it with winrar/winzip our whatever and count how many files are inside, for me its 8 I think with full mesmerize build but we are missing one file that the fascinate build has I believe.
Sent from my SCH-I500 using XDA Premium App
perhaps if download mode is busted you could flash a fascinate rom after rooting and then boot to recovery and try flashing something a little closer to home like one of the pick n packs for the mesmerize...
but this would be one of the last things I would try, right before the homemade jig.
Sent from my SCH-I500 using XDA Premium App
Are you sure you're using the right button press for i9000? Like the guy above said try Vol button down and plug in.
First time I have hard bricked a Samsung phone and would like to know where I went wrong. All we were trying to accomplish was to root the stock rom and change the revovery to CWM Touch. There was no attempt to upgrade to anything other than the stock rom. Here are the steps I followed:
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded cwm-touch-i717-120414.tar.md5 in the PDA slot
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and I let it sit until it timed out just to make sure everything seemed okay.
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded att_note_root.tar in the PDA section
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and seemed okay. On this boot a couple of things asked for root permission but I cant remember which apps. I attached the running phone to my computer and connected using USB Mass Storage. I copied flash_counter_reset_att.zip to the root of the SD card. Checked the MD% hash after copying to the phone. I powered off the phone.
Powered on the phone holding the Vol +/Vol-/Power to boot into CWM recovery
Chose install zip from sdcard
Chose install zip from internal sdcard
Chose flash_counter_reset_att.zip
Chose yes to flash
After the flash completed I went back and chose reboot system now
Here is where all hell broke loose. It was just a black screen and not recognizable by Odin. The phone is now on it's way to MobileTechVideos to get JTAG unbricked.
So my big question is what went wrong or what step did I miss?
WheresWaldo said:
First time I have hard bricked a Samsung phone and would like to know where I went wrong. All we were trying to accomplish was to root the stock rom and change the revovery to CWM Touch. There was no attempt to upgrade to anything other than the stock rom. Here are the steps I followed:
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded cwm-touch-i717-120414.tar.md5 in the PDA slot
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and I let it sit until it timed out just to make sure everything seemed okay.
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded att_note_root.tar in the PDA section
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and seemed okay. On this boot a couple of things asked for root permission but I cant remember which apps. I attached the running phone to my computer and connected using USB Mass Storage. I copied flash_counter_reset_att.zip to the root of the SD card. Checked the MD% hash after copying to the phone. I powered off the phone.
Powered on the phone holding the Vol +/Vol-/Power to boot into CWM recovery
Chose install zip from sdcard
Chose install zip from internal sdcard
Chose flash_counter_reset_att.zip
Chose yes to flash
After the flash completed I went back and chose reboot system now
Here is where all hell broke loose. It was just a black screen and not recognizable by Odin. The phone is now on it's way to MobileTechVideos to get JTAG unbricked.
So my big question is what went wrong or what step did I miss?
Click to expand...
Click to collapse
My Friend I'm so sorry to see this from you I really do feel bad for you I hope your phone turns out alright once it get's fixed I do not want to see anyone phone brick this is serious problem
Good Luck To you.......
What carrier version of the phone was it?
All Will Be Well
WheresWaldo said:
First time I have hard bricked a Samsung phone and would like to know where I went wrong. All we were trying to accomplish was to root the stock rom and change the revovery to CWM Touch. There was no attempt to upgrade to anything other than the stock rom. Here are the steps I followed:
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded cwm-touch-i717-120414.tar.md5 in the PDA slot
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and I let it sit until it timed out just to make sure everything seemed okay.
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded att_note_root.tar in the PDA section
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and seemed okay. On this boot a couple of things asked for root permission but I cant remember which apps. I attached the running phone to my computer and connected using USB Mass Storage. I copied flash_counter_reset_att.zip to the root of the SD card. Checked the MD% hash after copying to the phone. I powered off the phone.
Powered on the phone holding the Vol +/Vol-/Power to boot into CWM recovery
Chose install zip from sdcard
Chose install zip from internal sdcard
Chose flash_counter_reset_att.zip
Chose yes to flash
After the flash completed I went back and chose reboot system now
Here is where all hell broke loose. It was just a black screen and not recognizable by Odin. The phone is now on it's way to MobileTechVideos to get JTAG unbricked.
So my big question is what went wrong or what step did I miss?
Click to expand...
Click to collapse
I believe the "ONLY" thing you did (wrong?) was the att flash counter zip -Eliminate the Att step - there is a rooting method that does not cause the flash counter to be tripped (i believe it's non touch cwm - then flash the touch cwm - then flash Roms to your Heart's desire) I'm not really sure the flash counter issue really matters - At&t only cares if there is physical damage to the phone because I believe they just re-flash the phone and sell it again.
I'm Mostly responding to say that JTAG is Beastly and your phone will be better than brand new when you get it back - the status of your order won't change until they ship it back (which for me was 7 days), but don't panic (like I did) they are Good & Fast - So relax it cost you $50 & A week, but Hell the phone cost $700 so All Will Soon be well.
Also double check that it was the correct zip files for the Note - I bricked my Skyrocket because I flashed a Note Rom by accident (Thanks JTAG ) - I've got Too Many Samsung Devices - Hope This Helps.
bigdaddy4u said:
I believe the "ONLY" thing you did (wrong?) was the att flash counter zip -Eliminate the Att step - there is a rooting method that does not cause the flash counter to be tripped (i believe it's non touch cwm - then flash the touch cwm - then flash Roms to your Heart's desire) I'm not really sure the flash counter issue really matters - At&t only cares if there is physical damage to the phone because I believe they just re-flash the phone and sell it again.
I'm Mostly responding to say that JTAG is Beastly and your phone will be better than brand new when you get it back - the status of your order won't change until they ship it back (which for me was 7 days), but don't panic (like I did) they are Good & Fast - So relax it cost you $50 & A week, but Hell the phone cost $700 so All Will Soon be well.
Also double check that it was the correct zip files for the Note - I bricked my Skyrocket because I flashed a Note Rom by accident (Thanks JTAG ) - I've got Too Many Samsung Devices - Hope This Helps.
Click to expand...
Click to collapse
I have no issues with MobileTechVideos as I bought one of the first USB jigs when I got my day one Captivate. I am sure it will come back solid.
I did double check that I was using files specific to the Note, but I must say, you Note users have one finicky phone. I will stick with my Skyrocket. I'll look over the instruction for the non counter increasing root in the forums when the phone gets back.
Thanks
You didn't mention if you were able to get back to Clockwork. If you hold volume up and down while pressing power, it takes you straight into Clockwork regardless of the black screen. If so then you aren't bricked. Or if you still want to use Odin, hold volume down and power to get to download mode which is also Odin mode. Did you try these commands using physical button combinations and they did not work? If you didn't try them then you may be spending unnecessary money. If you did try all these things, then maybe you were hard bricked. Of all the Android phones I've owned and I've rooted all of them, I've never been unable to recover. I've only seen one hard brick from a coworker that had a galaxy s on tmobile that would not power on or charge after trying to root.
why did you even need a jig? turn on phone while holding down volume button.
madman604 said:
why did you even need a jig? turn on phone while holding down volume button.
Click to expand...
Click to collapse
+1. I'm so confused now. Maybe he tried to unbrick it first, then the phone turned hard bricked.
The flash counter is kind of a joke, isn't it? I mean, if the tech is looking to see if you flashed something, he cares that you flashed something, not how many times you flashed it.
I think the jig added another variable to the equation, and was unnecessary. None of the threads for rooting required one.
Also, i'd check to see if a MD5 is available for the files you used for the flash. Check the files you used and see if that was the issue.
If the note is new, and really is hardbricked, he's hopefully within the 30 day window. Just take it back for an exchange and tell them it stopped booting.
There is a thread started by ncoder in the international note general forum that has been near the top for a long time. You are not alone. Samsung actually responded!
Edit: Samsung desperately needs a stock failure. Maybe they would fix your phone for free so they could do a JTAG core dump that matches their sources etc.
Sent from my SAMSUNG-SGH-I717 using XDA
jordant2 said:
You didn't mention if you were able to get back to Clockwork. If you hold volume up and down while pressing power, it takes you straight into Clockwork regardless of the black screen. If so then you aren't bricked. Or if you still want to use Odin, hold volume down and power to get to download mode which is also Odin mode. Did you try these commands using physical button combinations and they did not work? If you didn't try them then you may be spending unnecessary money. If you did try all these things, then maybe you were hard bricked. Of all the Android phones I've owned and I've rooted all of them, I've never been unable to recover. I've only seen one hard brick from a coworker that had a galaxy s on tmobile that would not power on or charge after trying to root.
Click to expand...
Click to collapse
Would not go into Clockwork Recovery or Odin with any key combination, simply a black screen.
madman604 said:
why did you even need a jig? turn on phone while holding down volume button.
Click to expand...
Click to collapse
Jig is much faster, and works everytime, nuff said.
babymatteo said:
+1. I'm so confused now. Maybe he tried to unbrick it first, then the phone turned hard bricked.
Click to expand...
Click to collapse
Nope, started with a working phone and after applying the counter reset, which works beautifully on the SkyRocket BTW, that's when it bricked.
PaulF8080 said:
There is a thread started by ncoder in the international note general forum that has been near the top for a long time. You are not alone. Samsung actually responded!
Edit: Samsung desperately needs a stock failure. Maybe they would fix your phone for free so they could do a JTAG core dump that matches their sources etc.
Sent from my SAMSUNG-SGH-I717 using XDA
Click to expand...
Click to collapse
Thanks for the info.
Jamesyboy said:
The flash counter is kind of a joke, isn't it? I mean, if the tech is looking to see if you flashed something, he cares that you flashed something, not how many times you flashed it.
I think the jig added another variable to the equation, and was unnecessary. None of the threads for rooting required one.
Also, i'd check to see if a MD5 is available for the files you used for the flash. Check the files you used and see if that was the issue.
If the note is new, and really is hardbricked, he's hopefully within the 30 day window. Just take it back for an exchange and tell them it stopped booting.
Click to expand...
Click to collapse
I am beginning to agree that the counter seems irrelevant and wholly unnecessary.
Jig simply puts any Samsung phone that is off into Download mode, it is the same as the key combination only easier.
I always check MD5 hashes after I copy to the internal SD card.
I'm with the others on this... Flash counter reset was designed to work on ICS and not GB, I do believe that's where things went bad.
WheresWaldo said:
I am beginning to agree that the counter seems irrelevant and wholly unnecessary.
Jig simply puts any Samsung phone that is off into Download mode, it is the same as the key combination only easier.
I always check MD5 hashes after I copy to the internal SD card.
Click to expand...
Click to collapse
WheresWaldo said:
Thanks for the info.
Click to expand...
Click to collapse
I have no clue if the info applies to you. I just was hoping you still had possibly useful data in your phone. Saving face with your cousin was a side benefit.
Sent from my SAMSUNG-SGH-I717 using XDA
the only other step you forgot is to create a backup after flashing cwm
WheresWaldo said:
Thanks for the info.
Click to expand...
Click to collapse
I have same problem
WheresWaldo said:
First time I have hard bricked a Samsung phone and would like to know where I went wrong. All we were trying to accomplish was to root the stock rom and change the revovery to CWM Touch. There was no attempt to upgrade to anything other than the stock rom. Here are the steps I followed:
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded cwm-touch-i717-120414.tar.md5 in the PDA slot
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and I let it sit until it timed out just to make sure everything seemed okay.
Powered off phone
Inserted USB Jig (which powers on phone in Download Mode)
Started up Odin 1.85
Loaded att_note_root.tar in the PDA section
Plugged in phone (recognized as Com7)
Flashed
Phone rebooted after the flash and seemed okay. On this boot a couple of things asked for root permission but I cant remember which apps. I attached the running phone to my computer and connected using USB Mass Storage. I copied flash_counter_reset_att.zip to the root of the SD card. Checked the MD% hash after copying to the phone. I powered off the phone.
Powered on the phone holding the Vol +/Vol-/Power to boot into CWM recovery
Chose install zip from sdcard
Chose install zip from internal sdcard
Chose flash_counter_reset_att.zip
Chose yes to flash
After the flash completed I went back and chose reboot system now
Here is where all hell broke loose. It was just a black screen and not recognizable by Odin. The phone is now on it's way to MobileTechVideos to get JTAG unbricked.
So my big question is what went wrong or what step did I miss?
Click to expand...
Click to collapse
Hi all
i have the same problem , i flash a wrong file and phone is hard bricked
now i want to send to MobileTechVideos , i am in Kuwait so my question is
is it safe to send them or any one other in the region to whom i can send?
please suggest me what i should do
My Device is N7000
thanks
deleted...
I was under the impression that the jig didn't work with the note, I recall someone else bricked their phone using one a while back
Sent from my SAMSUNG-SGH-I717 using xda premium
jimmer411 said:
I was under the impression that the jig didn't work with the note, I recall someone else bricked their phone using one a while back
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
I agree. I have never even read of using a jig except for unbricking. Coincidence maybe but i wouldnt risk it again if you get a replacement
Sent from a big ass phone
Please Help me out.
I was using CynogenMod7 ROM. Could not write on my external SD card or mount it .
So decided to go back to Stock froyo firmware.
Tried ODIN to flash to my stock froyo firmware.
Had done it many many many a times earlier with success.
But ODIN could'nt complete the process, it kept on getting struck at Kernel and Factory some times.
Later thought there might be something wrong with bootloader.
Downloaded stock froyo bootloader.
Tried to ODIN the bootloader and got Struck at SBL many times ,Kept on trying then got struck at PARAM.
Removed the battery.
From than on NO Response what so ever combination buttons used.
No battery indicators,No light on Home keys, No signs of any power. Nothing Visible on screen & keys.
Tried usb JIG - no response.
Tried Ultimate UnBrick Resurrector-No response.
No lights .
Please solve my problem.
This may not work because I discovered this by accident. I bricked my phone so bad it looked like it wouldn't even turn on too. So, hopefully this works. Make sure you have your samsung drivers installed. Open Odin and connect the USB to the computer but not to the phone. Do a battery pull and do the three button boot, simultaneously connecting the USB to the phone. Most likely, nothing will happen. Hopefully, the phone will connect to Odin. Then, click start. That's right. Don't put any pit or tar files in, just click start. Hopefully, your phone will reboot to the vibrant screen and is stuck there. If it does, now you can reboot to download mode and Odin whatever files you wanted. If it doesn't work, just keep messing with the three button boot. I apologize for wasted time if it doesn't work. These steps are what I personally did on my phone. Hopefully, it works for you.
Sorry to say but I believe you have hard bricked your phone. If installing bootloaders goes wrong then your phone can turn into a paper weight. You could maybe try a jtag repair but I'm not sure it would help. You could call samsung and ask for a replacement, tell them you updated with kies or something but that's not exactly the truth
Sent from my SGH-T959 using Tapatalk
dr_rp1234 said:
Please Help me out.
I was using CynogenMod7 ROM. Could not write on my external SD card or mount it .
So decided to go back to Stock froyo firmware.
Tried ODIN to flash to my stock froyo firmware.
Had done it many many many a times earlier with success.
But ODIN could'nt complete the process, it kept on getting struck at Kernel and Factory some times.
Later thought there might be something wrong with bootloader.
Downloaded stock froyo bootloader.
Tried to ODIN the bootloader and got Struck at SBL many times ,Kept on trying then got struck at PARAM.
Removed the battery.
From than on NO Response what so ever combination buttons used.
No battery indicators,No light on Home keys, No signs of any power. Nothing Visible on screen & keys.
Tried usb JIG - no response.
Tried Ultimate UnBrick Resurrector-No response.
No lights .
Please solve my problem.
Click to expand...
Click to collapse
OK first, the stock images are 2.1 eclair not 2.2 froyo. Are you sure you have the right files? Are you sure your phone is a t959(3g, no front camera)and not t959v(4g, has front camera). Second, it sounds like a hard brick, if all else fails go to www.mobiletechvideos.com and check out the unbrickable mod and JTAG repair.
If you get your phone in DL mode and you have the correct Odin images, check the repartition box as well as others and run it.
Good luck
sent from my magic box to yours
Remove battery and sim and microsd. Leave out and press and hold power for 30 seconds or so. Leave battery out for a few minutes.
Put battery in and if you are on GB bootloader hold volume up and plug in USB. Might get you to download mode.
I did that with a friends phone about a year ago and got lucky. Odin recognized it. I read that somewhere here on XDA. May be a shot in the dark... but when you get desperate any new ideas to try can be a relief right?
Good luck to you.
After I messed with bootloaders and then tried to get back to stock with Kies I had this problem.
iTz KeeFy said:
You could call samsung and ask for a replacement, tell them you updated with kies or something but that's not exactly the truth
Click to expand...
Click to collapse
I called Samsung and told them that I was just trying to upgrade to 2.2 with their software and they replaced my PCB (printed circuit board) for no cost (including shipping). I have no idea if they tried to figure out if I had really used Kies (if they could even figure it out with the state my phone was in) or if they just replaced the PCB blindly. Worth a shot, I'd say!
Thanks for your concern.
Zeferden said:
This may not work because I discovered this by accident. I bricked my phone so bad it looked like it wouldn't even turn on too. So, hopefully this works. Make sure you have your samsung drivers installed. Open Odin and connect the USB to the computer but not to the phone. Do a battery pull and do the three button boot, simultaneously connecting the USB to the phone. Most likely, nothing will happen. Hopefully, the phone will connect to Odin. Then, click start. That's right. Don't put any pit or tar files in, just click start. Hopefully, your phone will reboot to the vibrant screen and is stuck there. If it does, now you can reboot to download mode and Odin whatever files you wanted. If it doesn't work, just keep messing with the three button boot. I apologize for wasted time if it doesn't work. These steps are what I personally did on my phone. Hopefully, it works for you.
Click to expand...
Click to collapse
Thanks for your concern.
But it did not work for me.
thanks
iTz KeeFy said:
Sorry to say but I believe you have hard bricked your phone. If installing bootloaders goes wrong then your phone can turn into a paper weight. You could maybe try a jtag repair but I'm not sure it would help. You could call samsung and ask for a replacement, tell them you updated with kies or something but that's not exactly the truth
Sent from my SGH-T959 using Tapatalk
Click to expand...
Click to collapse
Thanks for your concern
Its T mobile vibrant T959.
Its T-mobile Vibrant T959 without a front camera.
Totally no response.
No lights on soft keys ( Menu,Home,Back,Search)
No response even When connected with wall charger or PC.
Please help.
Thanks
dr_rp1234 said:
Its T-mobile Vibrant T959 without a front camera.
Totally no response.
No lights on soft keys ( Menu,Home,Back,Search)
No response even When connected with wall charger or PC.
Please help.
Thanks
Click to expand...
Click to collapse
Sorry to say this but your phone is hard bricked, as in nothing can save it but a JTAG or warranty service. You can try to call Samsung and say you hard bricked your phone cause of kies, it worked for another.
Sent from Mount Olympus via Hermes.
you can try this, it works for many user
http://forum.xda-developers.com/showthread.php?p=17858853#post17858853
HELP!
I need help with my Samsung galaxy SGH-T959 Vibrant I got bricked so I was fixing it with odin until my phone fell and it disconnected and red letters and numbers came out. when I try turning my phone on it doesn't until I press the buttons to go to download mode those red numbers come out and I can't do anything. Please Help
When you pulled the battery, after it hung up with Odin, you corrupted the primary Bootloader, because it wasn't completely written in......Last weak possible option is to try every rocker/battery/cable sequence ETC, to get Odin to handshake with the phone!!.....If there's still no sign of life after doing that....Your only option will be to have it JTAG,d in order to rewrite the primary bootloader file back in it.....it'll never power on unless the primary bootloader executes properly!!....you can corrupt the 2ndary BL and the phone will only be soft bricked, but a primary BL corruption is phone DEATH!!....Only place I know of that's reliable is: mobiletechvideos.com....send it to them, they'll rewrite the primary BL back in it and I think 2.1 or 2.2 for you and mail the phone back to you!!....Good luck let us know if you got it powered on with any combination, as that could save another Bricker from having to send it out!!
Randomness Guy........Start your own thread in the troubleshooting forum, AND QUIT TRYING TO HIJACK THIS THREAD!!