Related
Hi ,
I had 1.72.00wwe on my phone but i was tryin 2 upgrade it further but it got stuck while upgrading and its showing seril while not on cradle and while on cradle its showing usb 1.06
plz hlp me iam newbee and not good in programmin .I also have asecond Xda2 with 1.66.00wwe plz tell if it can b of any help
Reset your device, place it in the cradle and re-run the upgrade.
thanx i tried it already from 2 computers in one its showing error 103 no rom image found and in another its showing error 101 country code problem
Which ROM are you attempting to upgrade to? Which one exactly had you previously upgrade to? What operator do you use?
I'm asking all this to try and get a better picture. Normally, people in your situation can recover by applying the same upgrade again, or, at worst, re-applying the one they are upgrading from.
Make sure you are in bootloader mode (by pressing Jog button and Power button at the same time as pressing reset) before retrying any upgrade. Also make sure the USB cradle is plugged directly into a USB port on your PC and not through a hub and that the power supply is connected to the cradle. It may help to make sure that Activesync isn't running also.
active sync
in the active sync tray it shows that not connected
Well i had 1.72.00wwe rom image 1.14 earlier and iwas tryiong to upgrade to 1.72. something can't remember exactly but it was with rom image 1.17 it was downloaded from t mobile and my current phone is from o2
Click to expand...
Click to collapse
Activesync is not needed for upgrades. The upgrade process looks after its own connection. I suggest you follow the procedures in my post here to overcome the Country ID error problem. You will need to know what the device's operator and language IDs are currently set to, which is why I asked you above. I suspect you won't have Devicedata.txt, so it becomes necessary to know what operator and language the previous upgrade was.
to revive your XDA2 again
The main point is what is ROM 1.66 come from (e.g. i-mate ot T-mobile)
If you doesn't upgrade 1.66 ROM by yourself or it came from factory ,you must tell us which operator did you buy from.
If you try upgrade across operator ,it will hang on boot loader screen.
And again, which 1.72 ROM did you try to upgrade from?
I tried to upgrade my imate jamin s200 to smart1_wm6_pp8mb. since the operation did not finished I unplugged the usb cable, therefore the machine didn't work and opening now. now some messages are appearing on the screen (IPL:2.15.0001; SPL 2.15.0001; GSM 02.19.21; OS:10.1.0.811)
i need your urgently help... How can i fix it this problem and upgrade my rom again?
Put your Jamin into bootloader mode (camera button hold+softreset with stylus), connect it via USB (not on a hub!!!!) with your PC and try to flash the last update of Qtek, Orange, iMate or something else you like! If your device booting after this correctly you can re-try the flash to WM6!
I switched yesterday many times between Qtek 2.20 Ger, Orange UK, O2 Ger nd smart1's clear WM6 and had no problems during this!
Thank you very much, could you plase upload here i cant find the last update ,
i''m waiting you..
i dont know what is my qtek last update How can i learn it?
When you want to know what ROM you have flashed to your device, go to Start -> Settings -> System -> Device Information! Here you can find all information you need!
By the way: the latest Qtek update for the S200 is 2.20! You can find it trough Gooogle or the board search! Good luck!
animelover said:
Put your Jamin into bootloader mode (camera button hold+softreset with stylus), connect it via USB (not on a hub!!!!) with your PC and try to flash the last update of Qtek, Orange, iMate or something else you like! If your device booting after this correctly you can re-try the flash to WM6!
I switched yesterday many times between Qtek 2.20 Ger, Orange UK, O2 Ger nd smart1's clear WM6 and had no problems during this!
Click to expand...
Click to collapse
Hi animelover,
Just a question...Do you use the OS extract tool to flash only the os without changing the IPL/SPL, or the roms that you wrote about have no IPL/SPL upgrade? I mean did you fash directly or you flashed only the extracted OS?
Thanks!
Hi people,
I'm Luca from Italy, and I'm writing here hoping that You can help me to recover my dead PPC.
My PPC, when living, had Windows Mobile 5 like O.S.
So, As i've some problems with the phone I've decided to downgrade the radio version from 1.17 (people say that it is buggy) to 1.08.
So i run the HimaUpgradeUt_noID (I've also HimaUpgradeUt), but i've forgotten to delete the NK.nbf file from the directory.
I put the PPC in bootloader mode (SERIAL on top and ver. 1.06 on bottom) and then to the cradle directly to the motherboard USB connector
The sofware begin to update upgrading even ROM CE file, but when it arrived at 31% himaUpgrade stopped its work, showing that I need to reset (only normal reset and not soft reset) the PPC From this time until now my PPC show always and only the bootloader view.
When I try to upgrade again, the himalaya soft don't show what my PPC has like rom or radio version. It shows only the Ce rom and Radio that I'm going to ugrade.
It seems that software isn't able to erase ROM IMAGE
Active sync can't identify the device (some time it is indentified as unknown device).
When i start the software for ugrade the Active sync tray icon disappear.
I'm only able to ugrade radio stack or ExtRom.
PLEASE PLEASE PLEASE, HELP ME.
P.S. The device is unlocked
2 hits
http://www.expansys-kr.com/ft.aspx?k=21161
"Edited:- Problem solved, I loaded the upgrade from a different PC. I don't know why my main PC would not work as that is the one I regularly sinc the pocket PC to, but it just kept aborting the upgrade. Anyone else having this problem, try another PC."
if you're lucky
http://forum.xda-developers.com/sho...t=Failing+ROM+Update+Jam.+Error+112+CE+Failed
"it was stoping with an upgrade error at the very beggining of the extended ROM flashing no matter which ROM you were flashing to it! At the end they exchanged it for a new one, probably the ROM chip was faulty!"
if you're unlocky
Hi Rudegar,
first MANY MANY MANY THANKS for Your support.
I'm very unlucky.
I'm not able to upgrade my PPC.
The strange thing is that i can upgrade Radio Stack and even Extended Rom!
Only CE ROM wont' update.
Previous CE ROM installed was AKU 3.5 and Windows Mobile 5.0
Everythings worked fine.
Non other way?
I've seen that after launched del himaupgradeUt_noID the Activesync tray icon ho away.
My PPC sometimes ins't "seen" by my XP while other times it is "unknown device"
Why Can I only update RADIO and Extended Rom, while CE Rom not?
... P.S.
evey kind of button that I push the PPC is always in Bootloader Mode!
I'ev tryed: POWER + CAMERA + REC + STYLUS over the hole.
When I put the PPC to battery charger, red led is on until nothing is on the display, while when there is the written over the display, led is off.
No way to help me?
No news? I'm so sad
hello. i have the same problem but i have some suspections: i have 3 wersions of wm6 roms. one weight is 64 mb and others 32. and i tkink we are trying install rom from htc, dell or ipaq to our mda or other... so- **** this wrong rom and search for normal rom for himalaya ->
take this one :
"
mirror in china ,but very rapid downloading
http://exs.mail.qq.com/cgi-bin/downl...3f0dd183418032
enter the code e506cd02 then go
thx to c_shekhar
"
screenshots: wm6 pro. : http://www.engadget.com/photos/windows-mobile-6-professional/
cheers
Hi,
In Every ROM with WM6 and WM6.1 I got this trouble.
My QTEK S200 works fine with MW5 , when I install a WM6 ROM the sound dissapear.
First my QTEK S200 (HTC Prophet)
IPL: 2.20.0001
SPL: 2.20.0001
Radio: 2.47.21
OS: 2.20.7.35 WWE Korand 3.1 WM6.1
Protocol: 4.1.13.24
2 GB SD
Software Installed:
Coreplayer 1.1.0
SPB Weather 1.0
Oxios Memory 1.40
Battery Status 1.04.203 beta4
Windows Live for Mobile 10.6.0033.0600
How this happen...
1.- The Sound dont work, The Speaker.
2.- I can recibe call and call. But incomming call theres no sound only Vibration.
3.- When this happend I try to Open CorePlayer or any software for media and give a error " Wave Output: Devide Error !"
4.- Reset , the sound come back but...
5.- After this the ENDCALL Button works bad, after pressing this sound like a chime.
I got to rollback to WM5 and the trouble never come again.
I try a lot of things Reset, Flash , Reflash , Another ROM , bla bla...
And I confirm this only happen with WM6 and now WM6.1
I Think this is a software trouble , no hardware because when I turn the Volume down the weird Chime Sound go down too.
Please Gullum , HMA4 , Korand, Cloudyfa ... help me ... I dont know what to do ...
Seems only you have this problem, try to read step by step guide to upgrade again then flash to Korand 2.6 WWE, if the problem still happen, it must be your hardware problem.
IN your signature :
IPL: 2.20.0001
SPL: 2.20.0001
Radio: 2.47.21
OS: 2.20.7.35 WWE Korand 3.1 WM6.1
Protocol: 4.1.13.24
How can Korand 3.1 using SPL 2.20.0001 ??? when using korand 3.1 the SPL should be 2.g3.4pda.
To me it seems to be a software conflict. Try to keep your ROM clean after a reflash for some time. If you have this problem without any additional software installed, then the problem is with your Prophet (as you being the only one reporting) but I can't imaging because things work fine with WM5.
So give it a try and don't install anything exept your ROM.
@tb:
He probably used JumpSPL to flash, that utill don't change the SPL but bypasses it only once.
Looks like a radio Problem. change your radio, I think it will help just give it a shot ..
thanks guys
thanks for your comments ... since yesterdar I do a HardReset and work with the rom clean ...
Everything goes ok ... But lets see...
If the problem appears again I will notice you..
Thanks again..
PS HMA4 when you gonna bring to life a new Crystal ?
gzprophet said:
thanks for your comments ... since yesterdar I do a HardReset and work with the rom clean ...
Everything goes ok ... But lets see...
If the problem appears again I will notice you..
Thanks again..
PS HMA4 when you gonna bring to life a new Crystal ?
Click to expand...
Click to collapse
Hi, I can the same problem. I have korand 6.1 WW3. This problem is the same with Shadow (all version), Korand, etc. Do you find the problem? Im sorry for my poor english.
I have the same problem. It's not a big deal - happend only once or twice and after softreset the problem is no more. Using Konrad's 2.5.
Another problem that's more of a pain in the ass is that my prophet hangs once in a while. At times, when I press the power button to get it to standby mode it just won't turn back on - I have to soft reset it.
Problems such as not always working are something you must accept is going to happen when you put software on a device that it is not designed for. People like gullum and Cloudyfa try to remove as many problems as possible, but they will happen. Nothing can be done to prevent all problems, but the experts can sort most of them.
l3v5y said:
Problems such as not always working are something you must accept is going to happen when you put software on a device that it is not designed for. People like gullum and Cloudyfa try to remove as many problems as possible, but they will happen. Nothing can be done to prevent all problems, but the experts can sort most of them.
Click to expand...
Click to collapse
Yup, and we are pretty much aware of it But the guy was just pointing out the problem, so saying what you have said is quite pointless. Let's just try to work out the problems we can work out and try to "live" with the rest.
My comment was more about this:
Another problem that's more of a pain in the ass is that my prophet hangs once in a while.
Click to expand...
Click to collapse
me and my brother changed to WM6 and we both get the same problem that the sound goes off after some while and then i have to soft reset and then the sound comes back ,, this is a serious problem please try to find a solution
thank you
What ROM did you upgrade to?
Again ...
Hi , me again ...
I do a hard reset , work some days with a clean rom and the problem appears again ...
Clean ROM = No Sync, No Soft , No Apps , no Nothing !!!
A lots of tests ... So I Confirm that this problem is the ROM maybe the OS , some driver etc. WM 6 or WM 6.1.
I try to work some days without a SIM and the problem never come ... Maybe this can use as a clue for a solution.
I dont know what more I can do...
If HMA4 , Korand, Gullum or Cloudyfa need me as a tester for a solution to this problem I do it ..
Hi guys, I am experiecing the same problem.
Mine is a Dopod 818pro with SPL 2.20 and Radio ROM 2.69
Please advise your ROM versions to see if any clues.
Please Help !
Gullum, Cloudyfa, Korand, Hma4 and others developers ... please help us
I know of this problem with some builds and the workaround is to goto phone > menu > options and set kaypad of so no sound comes when pressing the numbers of the dial pad. some builds have the problem of disaparing sound after pressing in about 30 - 40 numbers on the phonepad.
Thanks Gollum
Thanks Friend...
So , you tell me if I turn Off the keypad tones the problem dont come back ?
But what about the Chime Sound when the Endcall button is preset ?
In my phone i Got the weird sound of the endcall button after the problem of the sound goes away ... a Soft Reset and the weird sound come ..
If you want in some solution for this I wanna help you as a tester..
Thanks again gollum
It sounds I was caught by the same problem, at least by looking. I got no sound from my phone speaker now. This happened after I try to play music through the Nokia BH801 BT headset. I installed a bunch of program but none works, and i lost sound after I installed BT 3900. Don't know if that's the reason, but I couldn't access bluetooth manager through BT 3900 indicating " insufficient memory". Plus, I got two BT icons in "connection" page now
I would like to remove BT 3900, but wasn't able to locate the file. I read the Enable_MS_BT.cab could do the job, but just can't find the file.
Please give me some clues to solve this frustrating problem. Thx a lot
...
I think that your problem is other ...
But why you dont try a Hard Reset, if the problem is Logical or Soft Driver , a Hard Reset maybe can be the solution ...
Try this ... and see if your Speaker come to life again.
so what is the solution ,,, now more than 10 people have the same problem but no solution????????????????? (((((
Hi, I have just purchased a second hand HD2 (Telstra Aust. stock) however it already had a custom rom on it (which i didnt like). I have been trying to install a new energy rom i can get the rom on and work except i cannot make any calls, I know the problem is the radio i have tried to install a new radio and when i go through the install stage it gets stuck on 0% and nothing happens. Im not sure which radio to use. The rom i want is: Energy.Leo.29007.sense2.5.Dec.7
My HD2 software details are:
OS version: 5.2.21869 (21869.5.0.82)
Manila version:2.5.19211619.0
Rom version:1.48.405.2 (71294)WWE
Radio:2.05.51.05_2
Protocol version: 15.28.50.07U
Any help would be greatly appreciated.
Switch phone off. Then while holding volume down button in, switch on the phone (keep holding vol down). The phone will boot into a multi-coloured screen. What spl version is displayed in the text showing?
You are correct about it being a radio problem. You have a .51 radio instead of the required .50 as explained in the Energy thread.
spl
im running 2.08.0000
Just download HSPL3 and replace your SPL2.08 to HSPL2.08
Then download EnergyROM and flash.
Make sure your RADIO is 2.08.50 and above. I prefer the 2.15.50 RADIO, but that is just me.
Thanks I will give that a go.
thnx man got it working just fine