Hi guys,
I tried to install a new ROM from SD card following all the steps included at the sticky thread. The tricoloured screen appears, it changes for less than a second to a white screen saying "loading..." and "No image file!" and then returns back to tricoloured screen, saying underneath "serial" (or if I try through cable "USB") and then nothing happens. What could be going wrong?
Thanks.
piesis said:
Hi guys,
I tried to install a new ROM from SD card following all the steps included at the sticky thread. The tricoloured screen appears, it changes for less than a second to a white screen saying "loading..." and "No image file!" and then returns back to tricoloured screen, saying underneath "serial" (or if I try through cable "USB") and then nothing happens. What could be going wrong?
Thanks.
Click to expand...
Click to collapse
Hi piesis, i have the same problem too, maybe is your sd card problem, have you tried to format it to fat32 format, if the problem still exist, try change
back the old sd card. If it can flash means its your new card problem XD
Related
Hello, I flashed athena ap4 rom
and stuck at gray loading screen
-the one that was suppose to show percent progress but now stuck there
and said "loading"
-when i get back to bootloader using hardward button
-it will get there and go straight to gray loading screen again
-flashing using sdcard was unsuccessful also
any suggestiosn, thanks
Remove minisd & sim card from your device
Go to bootloader using hardware button
Connect your device to PC using USB cable and then try to flash a new Rom
Good Luck...
Fixed! Thanks for you help!!
HELP
Solved after retrying a few times...now is really looking at Hard SPL the device so that I can change the ROM from CHT to ENG...
Thanks.
Hi all,
I have searched all over and can't figure out what is my problem. Any help would be greatly appreciated. I have TMO US H2. I've been trying to flash my phone for a few hours to no avail. I have tried to flash a few different ROMs via ActiveSync and I get an error saying it lost connection after it tries to access the bootloader. I then tried to flash it via the SD card, but can't get past the tri color screen, even with a signed ROM.
The tri-color screen shows the following:
PB81120 HX-B3
SPL-2.00.HSPL 8G XE
0x05
Cotulla aHSPL 0x50
Can anyone tell me why I can't seem to get past this screen when trying to flash a ROM?
Sounds like a task for task29. Search for it in this forum, and after you perform it - load a proper rom to your device.
I tried task29 but when it gets to the bootloader it gets stuck on the tricolor screen and says USB at the bottom, just like all the other times I tried to flash it. I get the following error message:
Error [302] - Update Error
The ROM update utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the errors so you can continue with the update.
What am I doing wrong? I keep seeing this error message every time.
so you can't even load a ROM from the sd card? that eliminates a bad usb.
You put a Rom image on the root of your sd card (usually needs to be 8gb or smaller). You make sure it is named LEOIMG.nbh. While pressing in the reset button (by the battery), you hold down the volume down button. Your phone should go into bootloader (tricolored) momentarily, then switch to a grey screen that asks if you want to update. press power for yes or vol up? for no. You press the red (phone call end button) and it errors? Is this what happens?
many people report the supplied 16gb card doesn't work for flashing.
for usb flashing, enter bootloader manually. wait for serial to become usb, and then run the flash.
im having the same problem. i have hardspl, i falshed a radio 2.07.50 just fine, then i tried flashing the rom via computer, the bootloader screen would not display the grey coloured screen where you 'update image' and it said lost connection on my computer. I then tried the sd card way, LEOIMG.nbh, same result - no grey screen to 'update image'
I installed Elegancia (stock/senseless) yesterday and noe I can't boot.
It's going to the htc One boot screen but hanging or if I try to go into recovery I get the 'Checking SD card update' message and then nothing.
Any ideas? I've had a look at similar threads but they've been no help
OH! And I can't get the bloody thing to switch off either!
Help! I just got CM 10.21 emmc running on my 8 GB NT and was becoming familiar with the system. I installed AdAway and after setting it up allowed it to reboot. Mistake!
This is the first time I've rebooted or turned off since the ROM flashing. I get the "N" screen, then an unnerving flash, followed by the Cyanoboot universal bootloader screen and it says "Loading (EMMC)...". Then all goes black :crying:
There is still backlighting and holding the power button will eventually extinguish it. Plugging the tablet into the charger (or the PC) has no effect (off or on).
It did the flashing according to this thread and everything went as described. The tablet has behaved flawlessly until this. I could theoretically recover to stock and start over again but if there is a way to fix this, I'd rather.
EDIT: Update. I tried booting with the CWM SD card that holds the recovery files as well as the files used to flash the CM 10.21 ROM. I get a red bar message that says "booti: bad boot image magic (in memory)". Underthat is "(SDC) LOADING BOOT...." and it's just stuck on that screen.
EDIT2: Solved itself eventually after a number of attempts. Really freaky behavior.
Hi
I have a Huawei S10-201u MediaPad 10 Link (S10-201u) and it is giving me grey hairs.
It had, what I assume to be, a custom ROM installed on it and we had no real access to the things settings. I decided to wipe and install the stock ROM.
PC OS: W7 SP1 x64
I went to Huawei website and downloaded the S10-201u Firmware (S10-201u, Android 4.1, C232B002, English)
Took forever but I eventually got an 2GB SD card, formatted it clean in FAT32, created a dload folder and dumped the two files (update.app and unlmt.cfg) into the folder and then switched off the tablet.
Inserted SD card, held down VOL-DOWN and pressed the power button until the logo appeared. Kept the VOL-DOWN button pressed until I saw the little green Android robot with the wireframe thing spinning in his chest.
It did its thing for about 5 minutes, bar moved some then filled a little more... and then it simply said "FAIL" in red and in yellow text it says "sdcard upgrade failed. reboot device"
And now it is stuck. I can't boot it normally (just keeps going back to the little green Android and saying failed), I can't turn it off (Can reboot it, just not switch it off) and I have tried 5 or 6 different ROMs on the SD to try get something to happen. No luck,
I am able to reboot the phone to a point where it says "Enter into fastboot mode" if I use VOL-UP and POWER.
Windows detects it in this format as an "Android Phone/Android Single ADB Interface" device however running "fastboot devices" or "adb devices" yields no devices in the list.
Any ideas and suggestions on where to go next?
Bump
I have same problem...
Is there anything what i can do To my tablet
Use a higher capacity SD Card...
Use a Higher Capacity SD Card and download the Stock ROM from
"https://yadi.sk/d/HLQjC5ozdh6xK"
Demonwolf said:
Hi
I have a Huawei S10-201u MediaPad 10 Link (S10-201u) and it is giving me grey hairs.
It had, what I assume to be, a custom ROM installed on it and we had no real access to the things settings. I decided to wipe and install the stock ROM.
PC OS: W7 SP1 x64
I went to Huawei website and downloaded the S10-201u Firmware (S10-201u, Android 4.1, C232B002, English)
Took forever but I eventually got an 2GB SD card, formatted it clean in FAT32, created a dload folder and dumped the two files (update.app and unlmt.cfg) into the folder and then switched off the tablet.
Inserted SD card, held down VOL-DOWN and pressed the power button until the logo appeared. Kept the VOL-DOWN button pressed until I saw the little green Android robot with the wireframe thing spinning in his chest.
It did its thing for about 5 minutes, bar moved some then filled a little more... and then it simply said "FAIL" in red and in yellow text it says "sdcard upgrade failed. reboot device"
And now it is stuck. I can't boot it normally (just keeps going back to the little green Android and saying failed), I can't turn it off (Can reboot it, just not switch it off) and I have tried 5 or 6 different ROMs on the SD to try get something to happen. No luck,
I am able to reboot the phone to a point where it says "Enter into fastboot mode" if I use VOL-UP and POWER.
Windows detects it in this format as an "Android Phone/Android Single ADB Interface" device however running "fastboot devices" or "adb devices" yields no devices in the list.
Any ideas and suggestions on where to go next?
Click to expand...
Click to collapse