Related
Hi Guys
My name is Luis and I live in Costa Rica. I have a HTC Jade which recently got the LCD screen broken . I really really appreciate if you can name me an Accesories Store located in USA to buy the screen. Since I live in Costa Rica it seems to be the logical place to import. HK is a little bit far from us!
Thank you in advance.
Brando ships worldwide and is pretty reliable. Why not use them?
On ebay.com I found some offers as well, some for about 33USD, like half price as from Brando Shop...
How to Dismantle
Hi,
I also have a broken lcd. I ordered a replacement from brando. Is there a service manual or dismantling guide that shows how to replace the LCD?
TIA
Scary Procedure
Hello! My touch screen is scratched and I bought another one to replace it. Well, it isn't so easy and after I dismantled the device, I decided not to replace it and wait for some tips because no documentation exists. No manual included with the package and no info on the net. (there are some youtube videos for other phones)
After you open the device, you end up with your phone in 3 parts. The Touch screen has a black marquee surrounding it witch I don't know how to remove, and it is connected with the main board with a very very thin wire witch I'm afraid to pull and I'm not sure if I have to pull it or do something else to remove it from the main board. Tips are welcome. Thank you!
since I am not allowed to post links, try following :
use google and type jade lcd dismantling. among pages you will see mikechannon.net, go there and find HTC JADE, click on it and here you are
yianp said:
Hello! My touch screen is scratched and I bought another one to replace it.
Click to expand...
Click to collapse
where did you find the replacement?
Marcell-o said:
where did you find the replacement?
Click to expand...
Click to collapse
I bought one from ebay. Unfortunately no instructions with the package
Kajmaj said:
since I am not allowed to post links, try following :
use google and type jade lcd dismantling. among pages you will see mikechannon.net, go there and find HTC JADE, click on it and here you are
Click to expand...
Click to collapse
Hey Kajmaj THANK YOU SO MUCH!!!!
yianp said:
I bought one from ebay. Unfortunately no instructions with the package
Click to expand...
Click to collapse
i've tried to open the device.
It's not so hard:
AT OWN RISC!!!
Unscrew the 4 screws, click it slightly open.
now you can see on 1 side a small flatcable for the digitizer, unlock it by swapping the behind of the connector. Unplug it.
Flip the PCB and unplug the 2 connectors for the screen and buttons.
Now you can unscrew 2 litle screws at the buttons.
remove the buttons carefully.
Now you can slightly press on the back of the old digitizer untill it loosses.
Place the new one, carefully press on the glue-parts untill you think it is tight enough.
Now read this post backwards to put it all together again.
If you're ready, push the on button.
When it asks for the pincode press : volume up + centerbutton to calibrate.
Et voila.
AT OWN RISC!!!
i'm not responsible for any damage.
Scratched external screen
Hi Marcell-o! I also managed to open it. But the problem is at the last step. the external screen has some kind of black "rubber" that holds it in place. that's where I don't know what to do. I attached a pic to see what I mean.
Thanks for your reply!
yianp said:
Hi Marcell-o! I also managed to open it. But the problem is at the last step. the external screen has some kind of black "rubber" that holds it in place. that's where I don't know what to do. I attached a pic to see what I mean.
Thanks for your reply!
Click to expand...
Click to collapse
You can leave it there.
You have to push at the back of the digitizer.
it's verry tight glued so you have to be patient and careful that you do not break the housing.
The rubber you talk about is meant to leave dust out of there.
i placed my new one just now and it works great.
I made some pictures of the repair and i'll post them tomorrow if i don't forget.
Pictures of the repair
Here are some pictures with some info.
And again:
AT YOURE OWN RISC, I'M NOT RESPONSIBLE FOR ANY DAMAGE!!
before the repair it was like this.
As you can see, it was in a very bad shape.
you can see what i use the most.
The "X" at the upper right corner and the IE scrollbar (yeah thats right, i use Explorer )
When you managed to open the cover you can see at the right side that there is a very small flatcable. (this is the Digitizer cable)
You can open the connector by flipping the handle to vertical.
Use tweezers to unplug it.
Now you can flip the mainboard. As you can see there are 2 more flatcables unplug them with tweezers.
by the way: #1 is for the screen and #2 is for the buttons
Place the mainboard on a safe place so it can't be harmed.
Now the hard part!
Unscrew the 2 very small screws on the red spots and save them on a place where you can find them back again (I lost one and it took a half an hour to find it back on the floor with a magnet whehe)
Now the screen and the button-PCB is ready to take apart from the casing. A bit of the flatcable is glued so be patient.
When you managed to loosen the screen and buttons, place this part at a safe place so it can't be harmed.
Now this is tricky.
Now you have only a front casing with the digitizer.
It's very tight glued so you have to press at the back of the digitizer to loosen it. Be patient, you can break the casing of your device.
Also take care that you do not break the flatcable of the old digitizer because you have to place the cable of the new one at the same way, take a look at the old one when you placed it apart from the casing.
You have to flip the cable like this picture when you placed the new one in the casing.
when you did this, you can replace a little cushion which you had to remove from the flatcable from the old digitizer.
Now replace the screen and button part. replug the 2 flatcables, place the mainboard its place, replug the small flatcable of the digitizer (be sure that the handle is vertical when you do this. When the cable is plugged, place the handle horizontal.
Replace the backcover, the 4 screws, simcard and the memorycard and batterycover.
Press the on button.
Et voila!
As good as new :
The only issue is, that we do not have a dust free environment like HTC has.
The result:
Don't forget to calibrate
All the pictures are clickable.
Sorry for my bad English
And now one more beer and a long sleep
Thanks!
Thank you Marcello! I will give it one more try.
Hi Marcell-o your guide looks solid and the pics look nice...
You are from the Netherlands, where did you get your screen? I am from Belgium, that's why I am asking...
I have two problems with my Jade:
1) My screen is all scratched up, and I need to replace it, so for this only the upper part is needed, right?
2) A few weeks ago when I was in the bathroom and took the phone with me there is since a square "oily" stain in the middle of the screen. I read elsewhere that it's due to the humid enviroment, so I guess I need to replace the LCD part too?
I saw that the screws beneath the backcover are Torx, but what number Torx is it exactly, and is that same Torx used for the screws on the mailboard of the phone?
Thanks in advance for any answers!
Greetz
I bought it here: http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=260513873708
verry good price!
I'm sorry, i do not know the torx number i was just happy to have the right one.
What you need for the scratched screen is indeed the touchpart(digitizer)
The screws inside(for the buttons/screen) are just the four points(?)(kruisschroef) The mainboard is clicked.
Can you make a picture of the "oil" stain maybe it's also solved with the digitizer replacement.
Hi Guys,
just this morning I've managed to replace a digitizer in my Jade, as it was punctured by some pointy child's teeth . A bit unlucky though, cause I couldn't find this thread before (silly me !) as to get some instructions how to do that.
I'd like to add some tips to Marcell-o's guide:
1. The tools you need are:
TORX T6 screwdriver for 4 outside screws
Philips PH0 (or 00) screwdriver for 2 inside (button panel) screws
Thin Tweezers for replacing flat cables.
Office/Swiss knife for replacing Digitizer itself​
2. To prevent any damage to your front cover, I would recommend to 'cut-off' the Digitizer from the inside, before pushing it out. I used a thin Swiss knife for this and started from the top corners, slowly going towards the bottom. This also left all (or most) of the glue at the case side so there was no need to apply additional glueing.
See attached Photo
[Sorry for adding like that, but I'm not allowed to add link as a new user]
3. To make your Jade scratch-proof as well as responding better to your fingers, I'd recommend the Advanced Screen Protector from ProPorta.com. It's nothing close to cheap crap from e-bay as 3 screens for a quid and literally increases touch sensitivity rather than decrease.
Good luck!
Catalan said:
Hi Guys
My name is Luis and I live in Costa Rica. I have a HTC Jade which recently got the LCD screen broken . I really really appreciate if you can name me an Accesories Store located in USA to buy the screen. Since I live in Costa Rica it seems to be the logical place to import. HK is a little bit far from us!
Thank you in advance.
Click to expand...
Click to collapse
would you sell it as is ? Pm me/
zubenelgenubi said:
Hi,
I also have a broken lcd. I ordered a replacement from brando. Is there a service manual or dismantling guide that shows how to replace the LCD?
TIA
Click to expand...
Click to collapse
and would you also ?
Hi,
I recently purchased a HD2 on eBay. It was supposed to come immaculate but unfortunately there are dents on almost all corners. Rest if perfect.
I saw on eBay some chinese sellers selling new housing + battery covers for ~25 USD. So why not replacing the housing then? I decided to give it a try.
Well I have to say that it really did not work like in the videos I saw on youtube. I removed the 4 screws under the battery cover, gently pressed the back of the LCM outward but it really refused to pop out (no even half an inch). I discarded the pry tool (a very thine credit card actually) and even tried using a suction cup on the digitizer to pull it backwards but same problem. It's like the LCM/chassis was glued on the bezel. Phone has never been disassembled before (white sticker and void screw were still both there).
This is strange because in all the videos I saw the LCM/middle chassis was clearly not glued on the bezel. It immediately popped out a bit then you could start prying (and praying!). Ok I know that in those videos usually the phone has already been disassembled before so other attempts require less force to do it again for the recording.
My questions now to all the people who managed to do this. Did this require so much force? Is there a change and is HTC now glueing this part the LCM/middle chassis to the bezel? Any suggestion? Where is for you the best place to insert the pry tool when you start?
Thanks and regards,
Try flexing the plastic bezel above the earphone outwards a little while applying slight pressure to the sticker area on the back. There're two notches above which locks the frame to the pcb.
Hi,
Thanks for your help.
I will try that later.
I guess I might need to find a better pry tool.
BR.
Ok I managed to do it.
This required clearly some force on the pry tool (actually I used two plastic cards : a very thin and flexible one than a credit card). I started the operation above the earphone area.
Applying pressure on the sticker area was stresfull because the LCD immediately reacted to the pressure (hence a risk to break it or damage it). Best was to put two fingers on the sticker area to help the LCM module to pop out but with (almost) no pressure.
I had a doubt and now that I managed to remove the housing it's gone. The antennas (those white stuff you see in both top corners and at the bottom) are glued to the housing.
I prefer to spend a few more bucks to take a housing which has those antennas already in.
BR.
i had a similar frustrating experience to yours in trying to snap the back off the chassis on my hd2 which had a fingerprint on the *inside* of the camera cover glass which i needed to open it to get at.
it sure looks easy in that HTC disassembly video on youtube but the tech there is using a sort of plastic hooked tool for the job, which i didn't have, so i used my thumbnail instead in the same place (the upper left corner, looking at the phone from the front) and it took me a good 20 minutes of applying what seemed like unreasonable pressure to my touchscreen and nearly tearing my nail off to get it to pop out.
those snap-tabs the electronics manufacturers use to hold cases together -- even when they also have screws to do the job -- are one of my all-time pet hates. i usually end up breaking them off.
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
fallenmonk said:
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
Click to expand...
Click to collapse
yep they are white thin bits glued to the top portion of the case. wifi on left and phone on right if i remember. its been quite a while though since i took my old hd2 apart
Now that I know how to do this I will be easier next time.
Yes antennas are glued in the housing so best is to buy a housing which has antennas already in.
Important note : the antenna which is at the bottom of the housing exists in two different versions : EU or US so check with the seller which one he sells.
BR.
Top left : Amphenol-BT&Wifi-090820
Top right : Amphenol-GPS-090820
Bottom : Amphenol-EU-090828
If T-Mobiles US you need Amphenol-US
sirec said:
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
Click to expand...
Click to collapse
i don't believe it's glued. as far as i can see the the case is held together with screws and plastic interlocking tabs. the trick is to get the latter to unclip.
No glue indeed just notches locking the LCM module to the bezel
Ok case closed
I got my new housing and the replacement went fine. For those who could be interrested I bought it on ebay from the seller forceviewer_uk in China. Everything went perfect so I can recommend this guy.
Hi All, I'm one of the few who faced the problem where one side of the screen is slightly lifted on the edge. It doesn't cause any functional problems, but the springy feel is annoying. It's probably the adhesive on the left acting up and not sticking well. Press the screen down, and it will uplift within minutes. Tried the hot air method to melt the glue slightly, but no use.
So I probably want to replace the adhesive, and began looking for teardown guides.
None, however, really shows if the Gorilla glass can be pried off from the top ,leaving the rear un-dismantled. The flex cable should goes to the mainboard at the back, but I don't need to disconnect that for this purpose. I'm also not sure if I should pry the top or bottom.
If anyone has done it before, kindly share your experience here.
Thanks
Full replacement seems like the best idea.
Sent from my SGH-I997 using XDA App
bzmotoninja83 said:
Full replacement seems like the best idea.
Sent from my SGH-I997 using XDA App
Click to expand...
Click to collapse
oh. Why so? Seems like an overkill proposal...
I have the same exact dilemma. I see this is an old post, but maybe someone else can chime in. I really don't want to dismantle an otherwise working phone just to reapply adhesive. I like the phone but this seems like a really poor design.
Anyway, if anyone knows of a way I can reapply the adhesive without total dis-assembly I'd love to hear it!
Mr. Shickadance said:
I have the same exact dilemma. I see this is an old post, but maybe someone else can chime in. I really don't want to dismantle an otherwise working phone just to reapply adhesive. I like the phone but this seems like a really poor design.
Anyway, if anyone knows of a way I can reapply the adhesive without total dis-assembly I'd love to hear it!
Click to expand...
Click to collapse
sorry you cant, im replacing the digitizer for mine and u cant take off the glass without ripping off the flex cable for the digitizer.
i suppose u can heat up the adhesive and carefully open it alittle bit and put some glue on that corner. i say glue because you probably wont have room to put double sided tape and remove the second backing without tearing the flex cable for the digitizer.
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
The likelihood the digitizer isn't cracked is very low.
NABI2 touchscreen layering:
front glass..............thick (glue around outer most edges to frame)
airgap......................very thin (glue around edges)
digitizer glass........thin
lcd............................thick
I tried the same thing but the actual digitizer glass is like 1/10 the thickness of the front panel glass and glued to it on the edges. If the digitizer glass is not cracked, it will probably crack on attempted removal from the front panel. If the digitizer is fully working in-spite of the front glass cracking it may be possible to heat the front assembly up to the point the adhesive allows the glass to just fall out.... but as far as how close the glue melting point is to the melting point of the plastic frame is not something I know. The entire assembly is put together with some super strong double-sided sticky tape. If you can source just the digitizer and glass assembly I'd like to know.
Once one attempts a replacement and it doesn't work is it still possible to get Fuhu/Nabi to replace the screen (at reasonable cost)?
( If not you could just plug in a keyboard/mouse and use the hdmi out... would make a great XBMC server... once the port exists... )
.
Pictures?
oranrene7 said:
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
Click to expand...
Click to collapse
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
manx_73 said:
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
Click to expand...
Click to collapse
I already put it back together because he was taking everyone's iPhones to play games on. lol The glass anatomizer (or whatever it's called), had a long thin strip and the LCD had a thicker one. Either way, the glass nowhere near fit. I had a feeling it was going to be too hard to replace anyway; hence the reason I can't seem to find a tutorial on fixing a Nabi.
And yes, Fuhu will fix it for like 85 bucks plus shipping...I only paid 90 for the tablet just recently (Craigslist). Oh well. I guess we'll just let him play till he cuts his finger.
Thank you both so much for your input. I appreciate it
Help replacing Nabi2 digitizer screen...
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
ChipStewart said:
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
Click to expand...
Click to collapse
I am also looking for the same digitizer model any luck? Anyone?
brianbri6 said:
I am also looking for the same digitizer model any luck? Anyone?
Click to expand...
Click to collapse
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
rex.torres said:
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
Click to expand...
Click to collapse
I am looking at a few on Fleabay now. You need to take yours apart and compare model numbers with the ones on Ebay. Just search ebay for Nabi 2 digitizer. about 20 results for it, ranging from $25 -65. The $65 one is a complete front panel minus the LCD. just unscrew the top panel and replace, it looks like.
Wow...I'm the original poster...and here I am years later still bothering with Nabi! lol In 2014, I went on Nabi's site and paid $60 to have the digitizer replaced. I never sent the Nabi in because a friend of mine gave me his kid's Nabi to use for parts (he couldn't get it to charge any longer). I took the entire front panel with LCD and digitizer and replaced it with mine. Worked like a charm...until my younger son stepped on it...on purpose! Lil turd! So, here I am again trying to fix the screen, BUT, this time I noted that I needed the LCD and the digitizer (the ribbon on the LCD was breaking off - not sure how that could have happened). At any rate, I ordered both the digitizer and LCD. I replaced them both and it's a no-go...not working. I still have it apart, but I have the cables plugged in, so when I move the screen around, the Nabi screen will come up, but the touchscreen isn't working. I may be sending the digitizer back, but I'm wondering if it's because of how they are lying on one another. Does anyone know if maybe the touchscreen doesn't work if it's too close or too far from the LCD screen. I don't mean by an obvious amount - I mean is there a "specific" amount of space. I am trying to get it in the casing exactly like it was before, but I don't want to do anything permanent until I know it's working 100%.
Also, you can easily and cheaply get the LCD and digitizer for the Nabi now - just stinks you have to order it from China and it takes forever to get here! I can only imagine how long a return/replacement is going to take. Ugh!
Oh, and Nabi has yet to return my $60 bucks...I have spent way too much on this tablet!
I ended up having to match my part number to a used but good part off of ebay. I had ordered several "new" digitizers and they never worked. There seemed to have been a design change somewhere along the line, or some missing information that made mine not work with the "new" parts available at the time.
However, to answer your question, the digitizer will work completely separated from the LCD as long as the ribbon cable is attached (of course). Rather than reassembling everything, I would only connect the digitizer to see if it worked. When I finally found one that worked, I then committed to doing the full repair.
It was a very painful process.
Is it an easy thing to take apart and put bk together if you have never done this before my daughter stood on her Nabi accident it was under her comfort blankie opps screen cracked but works fine she's only 2 ( well advanced for her age) soI dnt want her to use it incase she cuts her tiny fingers doesn't feel sharp but dnt want to risk it can't find any view on u tube still many years on be nice if someone would do one haha
Honestly...
It was a pain in the ass to remove the glass / digitizer from the nabi. If you're not careful--as I was--it is real easy to deform the plastic bezel that the glass / digitizer and LCD reside in. I ended up having to buy a replacement bezel that already had a digitizer and LCD attached to it. The LCD was DOA, but the one from my original was fine, so I begrudgingly transplanted that too.
Test the digitizer FIRST before committing to installing it on the plastic bezel.