Dear Experts,
I bought a T-MOBILE HTC HD2 from states.ii want to flash a new rom(Elegancia) on it.So that I can put Android on my SD card.but I am confused because when I press volume down button + red button ,I found:
PB81120 HX-B3
SPL-2.08.HSPL 8G XE
CotullaHSPL 0x05
0x50
Is HSPL pre installed?
my start up screen shows:
R 2.14.50.04
g 15.42.50..09U
D 3.14.04666 8G
It has :
Ram: 576 mb
Flash memory: 1024MB
Data bus:32bits
please suggest me what can I do to install android?
mlhazan said:
Dear Experts,
I bought a T-MOBILE HTC HD2 from states.ii want to flash a new rom(Elegancia) on it.So that I can put Android on my SD card.but I am confused because when I press volume down button + red button ,I found:
PB81120 HX-B3
SPL-2.08.HSPL 8G XE
CotullaHSPL 0x05
0x50
Is HSPL pre installed?
my start up screen shows:
R 2.14.50.04
g 15.42.50..09U
D 3.14.04666 8G
It has :
Ram: 576 mb
Flash memory: 1024MB
Data bus:32bits
please suggest me what can I do to install android?
Click to expand...
Click to collapse
Yes it was preinstalled by "somebody"
Cheers
Can I put the Android folder on microSD card now without changing anything and run it?Thanks for you answer.
mlhazan said:
Can I put the Android folder on microSD card now without changing anything and run it?Thanks for you answer.
Click to expand...
Click to collapse
You might be able to run it perfectly without robovoice, you may not. It's worth a shot. You're not "installing" anything, just running some files. Either way android will work mostly perfectly. HSPL just means you can flash a new windows rom if you want to.
technically, yes
Related
hello i'm in need of dire help! i flashed my htc hd2 with the dexter rom and all was well after that i tried to flash to a clean rom series and it doesnt happen!!! nothing! i can change anything. when i try to change my spl version its the same it says i need to have 1.42.000.i tried downloading it from htc website but after i input my S/N it says that this software was not made for my phone. could someone please help me? this is what my boot loader shows
PB81100 HX-BC
SPL-2.08.000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
you don't have hspl, run hspl3 choose 2.08.hspl then run your rom flash.
i have a hd2 that wont turn on,only when i connect d charger it comes on then it wont boot pass the white screen because it turn off,then comes back on n the same thing happen over n over.i manage 2 do a hard reset but it didnt help.also i tried holding down d vol key n the end key n i see a red,green,blue n white screen that display:
PB81120 SS-B3
SPL-2.10.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0X50
please help me
i would flash a new rom but make sure you have the right radio flashed for it first if not try a stock rom and flash from SD card and start from fresh
Right radio version is very important. Your HD2 is a TMOUS model, they need a radio rom that's compatible with 576MB RAM.
A good place for compatible radio's would be this thread.
Edit:
If I remember correctly, issues with wrong radio/rom shouldn't normally cause the phone to reboot by itself. Might be worthwhile to check your battery pins, to see if any might not be making a proper connection.
pls help me, i have followed many instructions how to instal android 2.2 or 2.1 but non of them works when i press cldcad then haret files from directory of my memory card in file explorer, black screen comes out with text. but it dont install, it stuck on 4-5 line of instalation.
what i can say about my phone
htc hd2
pb81100 hx-bc
spl-2.08.hspl 8g xe
r 2.05.51.05.2
g 15.28.50.07u
d 1.48.71294
pls help me.
Update you're radio to minimum radio version 2.08.50
Personally Radio 2.12.50 or Radio 2.15.50 are the best.
hi all, I hard formatted my windows phone 6.5, HTC HD2 and started setup for HSPL3 For HTC Leo. The setup started and failed and i'm stuck with it now. it gives me screen
HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
Micro(TOUCH) 0x40
and when i start phone power+volume down with leoimg.nbh in SD card the screen says
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
Micro(TOUCH) 0x40
Upgrade ROM code error. please try again
Serial.
Please help!!!
Common issue:
You still have standard SPL installed & thus require a ROM that is correct ROM code of original country/operator which the one on your SD card is not hence "Upgrade ROM code error"
Your 2 options are:
1. Use HSPL 3 or 4 to install a HSPL which bypasses CID lock & allows you to flash any ROM but by USB & RUU, if do from SD it overwrites HSPL with SPL everytime
2. Find a compatable CID code ROM & flash it ...
If this is a T-Mobile USA handset make sure to flash a ROM with correct radio or you will have a brick ...
Mister B said:
If this is a T-Mobile USA handset .
Click to expand...
Click to collapse
it cant possibly be a tmous with 1.42.0000 spl.
@OP, you are in the wrong forum, this is for tmo usa model hd2 only. (That's why there's so few recent posts, , , most tmous users are now in the android forums.
With the phone in the stripey screen (bootloader) connect usb, , when 'serial' changes to 'usb' you are ready to try running hspl again. What are you aiming for? if its android, (meaning your target is 2.08.hspl) use HSPL2 instead.
i have HTC HD2(made in china)
when i press power On Button then show( software update failed please try again)
when i turn on it on flashing mode in color (red greeen blue and white) then it shows.
PB81100 SS-BC
SPL-2.08.0000 8g XE
MicroP(LED) 0X05
MicroP(TOUCH) 0X50
UPGRADE ROM CODE ERROR PLEASE TRY AGAIN
what i have to do now please help.
depends what you want to do. looks to me as if it has been flashed from sd with a tmous stock rom, which has loaded 2.08.0000 which has then said 'this isn't a tmous' and given your error.
lets say you want to move to android
into bootloader
hspl4 --> 2.08.hspl (not 2.08.0000)
bootloader
flash magldr
magldr menu - usb flasher
use nand toolkit to set system partition size
magldr menu - 8 ad recovery
instal zip from sd card - choose zip - point it at whatever android rom you want to instal (zip on your sd card)
done/
also, you posted in the wrong section, prepare to be lambasted.
Please help again
i can change only hspl only as per below.
PB81100 SS-BC
SPL-3.03.0000 XE
MicroP(LED) 0X05
MicroP(TOUCH) 0X50
UPGRADE ROM CODE ERROR PLEASE TRY AGAIN
i want window 6.5 only not any thing . please help........
serial # is SH08PNW01126
made in china.
please help....
get any 3.14 winmo 6.5 rom.
put phone in bootloader, connect usb lead.
run hspl4
in the dropdown choose 3.03.hspl
when phone reboots, go again into bootloader
run the 3.14 rom.exe installaler.
done.
please help...
Thanks my dear for help me
but now i am facing a different problem .
my dear i have done it.
run into boot loader
run SPL4 and from filter SPL3.00 HSPL
Restrat
again start into boot loader
RUN ( ROM Upgrade for HTC HD2 (O2 UK 3.14.206.1)
it didn't completed.
got error
now turn off and didn't getting ON.
where is the fault.????????
please help.
At what % did you get error?
Explain how it won't boot, no power? Suck on boot screen? Can you enter Bootloader?
please help
1st when is going on into boot loader then during updating ROM it has stop at 8%.
after it got OFF and still not showing any thing. even i checked battery voltage . voltages are ok but leo not ok...
but from couple of days its not showing charging ' not showing any thing , even its not showing ( software update failed)
not entering in boot loader.
and not showing any thing on original charger.