Related
Hello XDA-Users....
I've got a little problem with my xda-device.
It's just doing not much. If i attach the device to the cradle. The system turned on and is beginning to start the ROM (I see the T-Mobile screen). I-ve got the hint that the installed ROM is 3.13. Radiostack and Protocol is empty. -> should be then GSM-Error in the bootloader.
After all this messages i've got an short "pling" (beep) of the device, and it all begins from starting....
I can not enter bootloader (nothing happens) and the battery won't be charged..... (There is no light)
I've checked already the fuse of the device. Looks good. What else do i have for possibilities to get the device working again? That the GSM-Part does not work is not important. I need the device just for testing and installing new software to include in the kitchen. So the phone function is not needed.
The battery semms to work, I still got some Volt if i check it with the multimeter.
Anyone have some tips for me?
Stefan
Have you looked at the connector on the base of the xda under magnification, it may be a bent pin on that or on the cradle that is preventing charging.
Connector looks good.
If i conect it, the device is getting power.
When i disconnect the cable / cradle the device stops doing anything and goes off.
If i do an hard reset with connected USB-cable, nothing happens.
If i try enter bootloader the display is flashing until i refuse the power button. Than endless "booting" starts again...
Stefan
It does sound like a low power situation, I think the gsm will not switch in unless there is sufficient power. If you need a battery I have one here that was removed from an xda a few months ago but should be fine, send me your address if you need it and I will give it to you.
That previous post was from me. Also have you checked that you dont have a stuck button.?
The buttons looks fine. tested them already. So that isn't the fault *damn*
If you can send me the battery, that would be very nice.
Maybe it's really the probelm. But i think, if the battery is in bad condition, there should be anway going a light on to show "going to load tthe battery".....
STefan
Stefan
If a hard reset doesn't solve the problem, then try this.
DO A FULL BACKUP FIRST!!!
Open the XDA, and remove the battery
(together with whatever circuit is attached)
Put the battery in the freezer for about 20 minutes.
Remove it, and reinstall it.
Now put it back in the cradle and it should charge.
Then to a restpore from the backup.
This just happened to me and it brought my XDA back to life.
A chemical process happens to rechargeable batteries that
prevents them from receiving a charge. Apparently freezing
the battery for a very short time (20 minutes) corrects this.
Try this at your own risk, but I did it to my only XDA and it is working fine
for about a week now. Otherwise I would have had to scrap my XDA.
Let me know how it works for you.
Joe
Joe_PDA said:
Stefan
If a hard reset doesn't solve the problem, then try this.
DO A FULL BACKUP FIRST!!!
Click to expand...
Click to collapse
--> Not able. Device doesn´t start.....
Joe_PDA said:
Open the XDA, and remove the battery
(together with whatever circuit is attached)
Put the battery in the freezer for about 20 minutes.
Remove it, and reinstall it.
Click to expand...
Click to collapse
--> done.....
Joe_PDA said:
Now put it back in the cradle and it should charge.
Then to a restpore from the backup.
This just happened to me and it brought my XDA back to life.
A chemical process happens to rechargeable batteries that
prevents them from receiving a charge. Apparently freezing
the battery for a very short time (20 minutes) corrects this.
Try this at your own risk, but I did it to my only XDA and it is working fine
for about a week now. Otherwise I would have had to scrap my XDA.
Let me know how it works for you.
Joe
Click to expand...
Click to collapse
Thx for the tip. Tried it, but didn´t work for me....
Stefan
Stefan
Sorry to hear it didn't work.
Its been over a week and mine seems to be holding up.
I'd have to guess you battery is completely dead.
i have the same problem
you seem to be having the same problem as me m8 do you have no radio
or information on the radio task bar.
my unit keeps on re-starting the same as yours and i cant access setup even after hard reset. i attempt to charge the unit and the pwr light comes on briefly then goes out after approx 10 secs the unit then starts itself up and as mentioned before turns itself on and off randomly.
(i have no software for this unit just the unit and charger no memory card)
i am new to pda's do i need any softwares if i get it working?
any feedback appreciated
Hi Guys,
I have recently successfully flashed my Nike to the NIKI_ROM_MARY_v0.3.3. It was working fine for the past 3 days apart from the odd frozen screen coming out of sleep mode (i think that had to do with some sleep/lock setting)
Then out of the blue I notice it power was off.
- I tried pressing and holding down the power button
- Removing the SIM, micro SD and battery and replacing with another battery
- Connecting to PC
- Charging
All to no avail...
Has anyone have any other suggestions before I return for warranty?
This worked for me; take the battery out leave the sim and memorycard inside the phone, attach the powercord wich is connected to the wallsocket ofcourse and switch the phone on, and then insert the battery........
2nd post cannot delete it?
i'm not sure but i dont think they will repair under warranty as you have changed the software
Same issue
I have the same issue with Mary's v4.0, if i reset or switch off the phone, it just dies, whatever I do it will not switch on.
I managed after 2 days, the keep trying to plug in ac power, with no battery, got a red charge light and then insert the battery, then hold down the power button, finally it booted, now i dare not switch off or soft reset.
obsydian said:
I have the same issue with Mary's v4.0, if i reset or switch off the phone, it just dies, whatever I do it will not switch on.
I managed after 2 days, the keep trying to plug in ac power, with no battery, got a red charge light and then insert the battery, then hold down the power button, finally it booted, now i dare not switch off or soft reset.
Click to expand...
Click to collapse
Here run well!!!
Flash my phone 6 or 7 times a day with new test and don't have any problem.
More details!!
Quentin Gran Torino said:
This worked for me; take the battery out leave the sim and memorycard inside the phone, attach the powercord wich is connected to the wallsocket ofcourse and switch the phone on, and then insert the battery........
Click to expand...
Click to collapse
if this does not work, then hold the on button and keep trying to insert, then remove and insert the battery until it starts (hopefully).
Just flashed another ROM, so doubt its ROM related, my suggestion is do the above, flash back to your original ROM and SPL, then send it back under warranty, this will be my 4th NIKI under warranty !!!!!!!!!!!!!!!
Quentin Gran Torino said:
This worked for me; take the battery out leave the sim and memorycard inside the phone, attach the powercord wich is connected to the wallsocket ofcourse and switch the phone on, and then insert the battery........
Click to expand...
Click to collapse
This worked for me. Seems to be a problem with the HTC Touch Dual. Several people I know have had the phone shut down for no reason. After the above, I did a soft reset.. No problems since... Touch wood!
Terry
Hmm, okay I know it's an old thread but I have the same issue but it happened with the original rom, I finally bring the phone back to life unfortenally not with my own sim-card.
For now I'm scared to do a sofreset because I think I lost my phone again just wondering what I can do, maybe someone on this forum have a solution for this.
Regards
I had exactly the same problem... may anyone be more specific?
http://forum.xda-developers.com/showpost.php?p=5579171&postcount=641
teorouge said:
I had exactly the same problem... may anyone be more specific?
http://forum.xda-developers.com/showpost.php?p=5579171&postcount=641
Click to expand...
Click to collapse
Hi teorouge, sometimes I got my phone back, what I did was:
1. Remove battery
2. Pressing softreset button about 10 times.
3. Insert battery and keep pressing the powerbutton until the phone reacts.
It's not a fix, the only thing you can do is use the phone but if you do a softreset the problem is back.
Personally I think the powercircuit is broken, I had to buy myself another Niki.
Regards
Rataplan said:
Hi teorouge, sometimes I got my phone back, what I did was:
1. Remove battery
2. Pressing softreset button about 10 times.
3. Insert battery and keep pressing the powerbutton until the phone reacts.
It's not a fix, the only thing you can do is use the phone but if you do a softreset the problem is back.
Personally I think the powercircuit is broken, I had to buy myself another Niki.
Regards
Click to expand...
Click to collapse
Thanks for the answer, I gave the Niki back to his owner... it's a corporate phone so he shouldn't personally pay any money (and me neither, that's for sure!) to get it repaired. Thou I hope for him they'll change it to a newer (and feature-rich) device!
Hi all,
I need an advice from you guys please:
My Topaz is not turning on, it simply does not do anything.
Last time I wanted to change the language but my battery was not fully charged, so in the process it suddenly turned off and since that time I am not able to turn it on, does not display nothing on screen when I press the on button it just vibrates continuously and not stop, and that´s it...
The charging light was on the 1st time I tried, but not the second time.
It is SIM unlocked but not hardspl´ed
Any advice would be great!
Thanks in advance
UPDATE 13-Mar-10
Today, I connected Topaz to wall charger, amber led turned for about 10 sec, then turns of, then vibrates, then nothing again.
I tried to do hard reset, nothing happened, then after some minutes the device is short vibrating every 1 min aprox, no led on, still can´t do nothing more.
EDIT: After 15 min of short vibrating every 1 min, now it´s completely dead again........
Thanks for reading,
Can you put it in bootloader? Is a hardreset possible?
Try to turn the phone off, remove battery, and insert it again. Then hold vol down and press power. Do you get red/green/blue (or whatever) colors?
If you do. let it boot until it says USB (perhaps need to connect usb to PC for it to change from serial to usb) and after that just run the topaz ruu and it should flash.
If you dont get it to start to 3 color screen try and hold up+down and press power.
yes, Vol down and powerbutton. should boot to serial/usb flash screen.
Thanks guys for your reply
Soon as I get home I´ll try and report back
Cheers,
Flash a stock ROM
jmkhenka said:
Try to turn the phone off, remove battery, and insert it again. Then hold vol down and press power. Do you get red/green/blue (or whatever) colors?
If you do. let it boot until it says USB (perhaps need to connect usb to PC for it to change from serial to usb) and after that just run the topaz ruu and it should flash.
If you dont get it to start to 3 color screen try and hold up+down and press power.
Click to expand...
Click to collapse
Hi
Just check that if you try to reflash the ROM whether you should use a stock ROM vs modified ROM as you wrote that you do not have HardSPL on your Topaz.
Once you have successfully reflashed using stock ROM do a hard reset and then install HardSPL 1.83.
Good luck
Aussie
Still need help!!
Ok guys,
Let me explain you what happened:
None of the instructions above worked...
Can´t put on bootloader, hard reset nothing happens
When connected to wall charger amber led is on, if I press power button led turns off and vibrates, then led turns on again but nothing else happens.
Pressed down vol and power = Nothing happens
Pressed up/down vol and power = nothing happens
EDIT: Connected to PC and automatuically installed a qualcomm driver not detected also by WMDC
Disconnected from PC then connected again to wall charger and now amber led not turns on....
Please help!!
Any other advice please!
I really don´t know what else to do
Thanks in advance for taking your time on this thread
Per your PM, I'll certainly help you if I can.
Do you happen to know what caused it to brick? This will help determine how to bring it back. Did you attempt to flash a custom ROM w/o HSPL?
I am not an expert on this but have seen some chefs claim they can bring back a bricked device.
There is a program called MTTY that can usually get your phone to connect to your PC and there are functions to run in that program that can get it to a flashable state so you can reflash your shipped ROM.
Also search the Wiki for restoring bricked device, regardless of the model, it should be the same process. I think I have seen this in the Tilt(Kaiser) forum and maybe in the Fuze (Raphael) forum.
I haven't used this program in a while so I forget the commands but you should be able to find them in a search.
In the meantime I'll do a little research too and see what I can find out.
The main thing we need to accomplish is getting you back into bootloader mode.
1. Here is a link for recovering a Hermes and it has info on mtty.
Thanks a lot Bruce,
I have the original ROM and my Topaz is the unbranded model.
I was just trying to change language but battery was too low, then it turned of and you know the rest of the story.
I have it SIM unlocked but not hardspl´ed and I was not doing any ROM upgrade or so...
I´ll try to use MTTY and find about your recommendations, later report back.
I appreciate a lot your reply!
Cheers,
EDIT: Tested MTTY but in some point says "power on the unit " but that is what I can´t do, nothing happens
Will continue testing and searching...
This is from the Wiki. It may help. Says to use PUTTY instead of MTTY... with instructions.
Another thread on recovering device.
Bruce Inman said:
This is from the Wiki. It may help. Says to use PUTTY instead of MTTY... with instructions.
Another thread on recovering device.
Click to expand...
Click to collapse
Thanks Bruce,
I went through both links but nothing...
The main prob is that I can´t even make it turn on...
Now when wall charger is plugged I do not have the charging led on, so I am really lost...
I do not have another battery to test but I don´t think is that because Topaz is almost new!
But Now I think it´s not charging the battery...
Hope any other idea can save me
If it is almost new try to send it to warranty!if it has the original hspl no prob then!is better then trying to reapair youself, with the cost of loosing warranty!
Good luck with that!!!
Thanks, but I do not have that option
I have high hopes with all the great team of XDA!
first thing first,you have to have power in your phone.....borrow the battery from someone or recharge your battery in somebody else's phone.......then try to go in to bootloader mode (volume button down and power button)..........
komsa said:
first thing first,you have to have power in your phone.....borrow the battery from someone or recharge your battery in somebody else's phone.......then try to go in to bootloader mode (volume button down and power button)..........
Click to expand...
Click to collapse
Yep!
I ordered today another battery
Soon as I get it will report back.
Thanks,
Maybe this will help
It happened to me once. Nothing seemed to work. What did work, I left the phone charging for a day. First take ou the battery for at least a minute. Put it back on. Then connect the wall charger to the phone and let it charge. Hope this will help.
When it happened to me the LED wasn't working either, just connect the charger and let it charge.
Thanks,
I done that yesterday and left it all night but nothing...
I really hope is a battery problem, I´ll find out soon as I receive my new one
wrong place
Exactly samething happened to me.. the only difference was that I was using google maps and connected to my car charger. It somehow didn't charge and ran out of power and kept restarting whenever I tried to charge from a wall-socket.
This is what i did... worked for me.
Take out the battery from the back
Hold down the power button for at least 30 seconds to drain out the static charge.
Take out the sim
Plug in the USB to the phone (without the battery and without the sim)
With the phone connected, press the Red button at the back (soft reset)
Unplug the phone from the charger
Put the battery back in
Connect the USB to charge
Cross your fingers and say a lil prayer
Wait for 30 minutes
Turn it back on.
Lemme know how that goes 4 u
Thanks
I done all your procedure but after this point: [*]Connect the USB to charge
Led charging light did not turned on...
By now my only chance is to test with a new battery (which I will receive on thursday), but I do not have too many hopes as the device is almost new
I´ll report back on friday.
Thanks to all and I will be happy to receive any other suggestion
Hi. The phone application was not functioning well and the F/C dialog showed up. I powered off the phone and from that point, the phone won't turn on.
The battery was fully charged before this happened.
When I press the power button, the phone vibrates for half a second, the screen brightens up but does not show anything but a black screen.
I removed SIM and SD cards, removed the battery and performed the above steps but nothing happened.
I also tried to put on the charger to see what's going on. Once I plug the charger, the phone's screen brightens but shows only blank (even without pressing the power button)
When connected to the charger, the green light for charging is on for some minutes, then goes off automatically.
I tried to connect it to the PC, and PC Companion finds the device as usually. It even shows the dialog on the pc screen to mount the device.
I tried a hard reset, but does not work
On some point, the sony logo appeared and then a dialog saying: "sorry process system is not responding". The first time I pressed Force Close and the phone turned off. Immediately after that, the phone turned on and showed the exact message. I pressed "Wait" but nothing happened in the next 15 minutes.
I called Sony's support center and they suggested a software update. Did the process exactly as it should, but again, even after the software update the screen shows nothing but black. It is all the time brightened for some reason.
I tried to turn off the phone for some time by removing the battery, but as soon as I put the battery back on, the phone's screen brightens and stays that way forever.
The phone was functioning perfectly up until this issue. The only application I had installed apart from some games, was AWDLauncher. On the screen I had only a TASK widget and a battery status widget.
The phone is 3 months old and has been always in perfect condition.
ANY help would be appreciated!!!!
Many Thanks
Try to format phone with this method hope it should work as it seems the issue is with OS only ..
http://forum.xda-developers.com/showthread.php?t=717949
Many thanks for the prompt reply. I will try to do so and let you know how it goes!
o0k00l said:
Try to format phone with this method hope it should work as it seems the issue is with OS only ..
Click to expand...
Click to collapse
I tried the steps found in the link you gave me, but I couldn't go any further after step no (5) from the tutorial, as it would require to enable Debugging mode and I cannot access the OS (since the device won't turn on).
Is there a way to format all the contents of the device and have them replaced by running SEUS (as it always says that my device is up to date now)?
Was it this:
http://www.sonyericsson.com/cws/sup.../detailed/updateservice/xperiax10?cc=gb&lc=en
That Sony Ericsson told you to do?
If not, use that.
Download it, follow the steps when it says you have the latest version, press "Install Anyway".
Hope this works.
Hi itTim. thanks for the response
this is what i did but no improvement at all ((
Sounds like you broke your LCD screen somehow.
That would suck because I broke mine and it cost me $200 to fix.
Hi Hypercore.
Yes that could be the problem. The thing is that I always took rally good care of the phone, always carried in a leather pouch and never droped it. How sensitive is this lcd anyway?? Did you notice any cracks on your lcd or was the problem simillar to mine?
Thanks
When you turn on the phone does the lcd backlight turn on?
If so, look for any faint lines of color (usually a hairline size). If you see any of those then your screen is cracked.
the backlight is on, but there are no lines of colour on the lcd screen.
another weird thing is that the green light on the top blinks one or two times every time i put on the battery. even if the phone is off, once I insert the battery turns on automatically after a couple of seconds.
If all else fails you could try to flash back to your original fw with the tools here:
ht tp://forum.xda-developers.com/showthread.php?t=683793
AyDee said:
If all else fails you could try to flash back to your original fw with the tools here:
ht tp://forum.xda-developers.com/showthread.php?t=683793
Click to expand...
Click to collapse
That won't do anything.
I had almost the same issue. Nothing worked. But, when I removed the battery and left it for a day (24h) without it, it just started working again. Still working without issues..
Good luck!
Devtone said:
I had almost the same issue. Nothing worked. But, when I removed the battery and left it for a day (24h) without it, it just started working again. Still working without issues..
Good luck!
Click to expand...
Click to collapse
Phones are very wierd pieces of technology. I once bricked my k610i and that's a phone that's supposed to be impossible to un-brick, but out of nowhere a month or so later i picked it up, hit power and it turned on perfectly. Made no sense at all, but it worked.
Taking the battery out for a long time probably took all the electrical charges from it (kind of like how a computer power supply / monitor can hold power charges) and reset your handset.
Hypercore said:
Phones are very wierd pieces of technology. I once bricked my k610i and that's a phone that's supposed to be impossible to un-brick, but out of nowhere a month or so later i picked it up, hit power and it turned on perfectly. Made no sense at all, but it worked.
Taking the battery out for a long time probably took all the electrical charges from it (kind of like how a computer power supply / monitor can hold power charges) and reset your handset.
Click to expand...
Click to collapse
Indeed. It could be a frozen chip, memory fault, power-regulator and so on.
Hypercore said:
That won't do anything.
Click to expand...
Click to collapse
Ah, debug mode needed- I see now
tasaki said:
I tried the steps found in the link you gave me, but I couldn't go any further after step no (5) from the tutorial, as it would require to enable Debugging mode and I cannot access the OS (since the device won't turn on).
Is there a way to format all the contents of the device and have them replaced by running SEUS (as it always says that my device is up to date now)?
Click to expand...
Click to collapse
if you have done this and did not worked , then it is the LCD.
send it to workshop and check it there.
Guys i Really need the solve of this problem , my xperia has blank screen now without backlight and the phone completely doesn't work . when i put the battery and prees the switch botton it gives me 3 red signals , i've updated and hard reset but it didn't work , and btw the LCD is fine , any idea. did removing the battery worked???? . please answer
After a looooot of time since my latest post, finally my Xperia came back to life. There was a battery failure which means the phone was ok all the time. Weird thing is that the led light showed that the battery was charging ok. I removed the battery and after a lot of time it is working ok again. This was really really odd.
FYI for anyone else that gets this issue.
I just had this for the past hour after trying to change my baseband....could not get it back for anything.
What I did finally try was run another baseband via flash tool, connected to usb and it started flashing....after flash phone powered on again...yeah I agree with everyone, that is freaking scary when it happens.
When the power button is pressed, the screen goes off and then turn back on.
I noticed that if I insert the USB charger and I press the power button, the screen goes off, and after taking out the USB charger, sleeping mode works ok for a while.
Some times, I have to try more times to insert the usb charger and press the power button to make it to work.
I noticed when the phone is working in this weird sleeping mode, the battery is discharged very quickly. (a well charged battery is discharged in less than an hour!)
Thanks for any help.
ullsign said:
When the power button is pressed, the screen goes off and then turn back on.
I noticed that if I insert the USB charger and I press the power button, the screen goes off, and after taking out the USB charger, sleeping mode works ok for a while.
Some times, I have to try more times to insert the usb charger and press the power button to make it to work.
I noticed when the phone is working in this weird sleeping mode, the battery is discharged very quickly. (a well charged battery is discharged in less than an hour!)
Thanks for any help.
Click to expand...
Click to collapse
Backup your data and do a hard reset. If the problem persists, consider repair service. This sounds like a hardware issue.
next time check where you are posting, you posted in a Rom Develop section, you should have posted this in the general section.
Sorry, I will more careful next time.
thanks.
i have same problem here in Thailand.
in windows i can't go to sleep mode screen keep always on ..... except charge battery or connect USB to computer. but some time it just automatic wake up again .
but later i found in ANDROID which i run from SD CARD it can put screen off ??????
it run "ANDROID" perfect with any rom and any radio rom
if it is hardware issue. why android is just perfect ????
i try to task29, flash new rom ,try every radio rom ,and official rom from Thailand.
but problem still with me.
look for the vdo
http://www.youtube.com/watch?v=2t3ZJbnMrPU
http://www.youtube.com/watch?v=IURYQr20rWQ
http://www.youtube.com/watch?v=DUEigdP5qZ8
Can any one move this to general topic?
Thank you!!!
problem solve!!!!
after test 1 week with this rom and newest radio rom
http://forum.xda-developers.com/showthread.php?t=610634
Duttys_2.5_5.29013.5.3.11_3.14_HD2_ML_Family_ROM_(V19)_ASIA.7z 155.07 MB
problem gone