Related
my x10 die suddenly, there was 94% battery left, not plugged out long, few hrs later notice phone was off,and it will not power on again, press power to try to turn it on all it does is vibrate and that's it.
tried to flash stock 2.1 back on but not sure if it did anything, took over night or flash tool to finish, still no boot after that, press power and it vibrates that's all, sometimes it doesn't even vibrate, battery is good, works fine in another x10, put a fully charge battery in it and same result.
anyone know what happened to it?
was running eternity 3a rooted with DT.
I'm going to have to send that in for warranty, hope they won't find anything on it and void the warranty.
Was the phone quite hot at the time or heating up when trying to boot?
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
sharathx10 said:
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
Click to expand...
Click to collapse
That usually does the trick. Unplug battery for 1 minute, reinsert it and try again.
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
do you have a SD card inside. Might be a bad SD card try taking it out and booting it. Happened to me before.
blagus said:
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
Click to expand...
Click to collapse
Hi, just wanted to jump in and ask a few questions about this situation.
Do you always experience this issue? How long before it freezes? What "act" are you doing to prevent freezing? Does the phone work normally afterwards?
Hope you can help me out with some answers, I want to look into this.
instead of starting a new thread,i'll post here..
i have this restart problem..
Before this i try to fix my friend X10.. after many tries and a month acctually,i give up..
Now one more of my friend gave me another X10 which have the same problem..
Problem:
The phone will boot but after several minutes it will auto shut down and when i try to power up no vibrate and stuck at black screen.
when i pull the battery out and on again it vibrate and boot.just after boot animation it will shut down again..
Solution that i have tried so far:
Update with SEUS.
Send to profesional phone service to downgrade to 1.6.
Upgrade/flash with flash tool with GENERIC
Upgrade/flash with flash tool with X10_1.0_SE_StockRom_MultiTouch
Wipe user data in flash tool & x recovery
after several tries i got it work and i root and install x recovery.
Flash from xrecovery with custom rom Eternity.build003a.signed
format memory card.
Change battery.
All the solution i've tried doesn't make the problem dissappear.
anyone have ideas or solution?
Hi,
I have an Xperia X10 with Cyagenmod 6 (gingerbread 2.3.3) but it's broken. It won't boot any more. Some days ago it just went out, and it won't start up again. The phone behaves as if it freezes the moment android should load. Like if your computer would freeze in bios, unable to load your operating system.
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
I am kind of a noob with these things and therefore hope one of you guys could help me out. I'm not really looking foreward te buying a new phone already
Thanks!
Freekh
kinda same problem..
i'm removing battery, put back and after holding power the phone shows green led for short time and vibrates for a sec and that's.
add:
i've flashed it before the problem occurs.. flashed, phone booted up, everything normal.. put on usb for charging, changed language and time when it suddenly freezed
This is what happened to mine what country u in
sent with a geordie kiss using wb 2.3.3
what do you mean with "country"?
freekh said:
Hi,
I have an Xperia X10 with Cyagenmod 6 (gingerbread 2.3.3) but it's broken. It won't boot any more. Some days ago it just went out, and it won't start up again. The phone behaves as if it freezes the moment android should load. Like if your computer would freeze in bios, unable to load your operating system.
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
I am kind of a noob with these things and therefore hope one of you guys could help me out. I'm not really looking foreward te buying a new phone already
Thanks!
Freekh
Click to expand...
Click to collapse
Try re-flashing the stock rom using flashtool. That solves Every problem for me ^^
freekh said:
Hi,
...
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
...
Click to expand...
Click to collapse
not able to flash anything
blmn1337 said:
not able to flash anything
Click to expand...
Click to collapse
Why exactly are u unable to flash anything? Are you following the proper procedure?
Here's a guide fro using flashtool http://forum.xda-developers.com/showthread.php?p=10879507#post10879507
fawadmir said:
Why exactly are u unable to flash anything? Are you following the proper procedure?
Here's a guide fro using flashtool http://forum.xda-developers.com/showthread.php?p=10879507#post10879507
Click to expand...
Click to collapse
i've posted some logs in other thread
http://forum.xda-developers.com/showthread.php?t=1190540&page=2
umm.. Do u move your mobile when the flashing process is going on? The xperia USB slot is pretty sensitive. Moving the phone can cause it to lose connection and abort the flashing process
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
i always receive this error if i move my phone.
Notice if you hear the USB device unplug sound from your PC before this error occurs.
^^
fawadmir said:
umm.. Do u move your mobile when the flashing process is going on? The xperia USB slot is pretty sensitive. Moving the phone can cause it to lose connection and abort the flashing process
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
i always receive this error if i move my phone.
Notice if you hear the USB device unplug sound from your PC before this error occurs.
^^
Click to expand...
Click to collapse
it doesnt seem to be a connection-problem (no usb unplug sounds).
it seems that the phone is in a state, where bootup is not possible
But the phone is not required to boot during flashing. Did you try changing the USB slot on your PC? The one you're connecting your phone to? Try another slot. Sometimes that works too.
fawadmir said:
But the phone is not required to boot during flashing. Did you try changing the USB slot on your PC? The one you're connecting your phone to? Try another slot. Sometimes that works too.
Click to expand...
Click to collapse
same result. can't flash
Me too. Can't flash with Flashtool (latest version), even without moving my phone. It starts flashing, but the progress bar shows of no progress. After a while it just says Error - Abort Flashing. I tried all of my USB port, but nothing changes.
after doing and trying my battery got completely drained (red led blinking) so i left it on the wallcharger for ~1day..
then at sometime it managed to boot up itself.. i left it for charging till 100%
after that i did a few "wipe battery stats" in xrecovery and now it seems to work stable again..
is it possible that messed up battery stats could cause the problem?
Wow, that would be nice.
A question! Was the little led on while charging? Because when I put my phone in the loader, it turns green (as if the battery is completely empty) and after a while it just goes off (when it would normally turn red). Do you have that to?
Putting my phone in the loader now, and waiting till tomorrow! Hope this helps!
yea, i've noticed this with my phone too..
strange led behavior..try to plug the charger first (green led turns on, cant say whether its charging or doing anything else) and then put in the battery and wait
maybe you're lucky and the phone will boot
and report pls
I didn't work. I've put my phone in the loader for over 24 hours, but nothing happened.
But my phone wasn't completely drained. Perhaps that is a condition to make this work. The only question is, how do I drain my battery when I can't turn on my phone?
i have used an 5watt light bulb ^^
connected on + and - and then waited till light goes out
Wel, I connected a little lamp and waited until it went out. Then when I put my battery in my phone and pressed the ON button nothing happend, not even the green light flashing shortly.
When I put my phone in the loader the LED started flashing red. And that whent on for a while until it stoped, and the LED did nothing. Then I waited over 24 hours, but nothing has happend.
When I put my phone in the loader now, it's just like before, the green light burns a little while, then nothing..
it happened to me again.. freeze and then no boot.
but i think i know whats wrong. for my phone i can say, that the battery is ok and the rom/os aswell.
its hardware problem. something is screwed up inside the phone.
when i press the phone at randomly places and hold it + then pushing on-button it boots up
i will open it tomorrow
Okay, so recently, maybe a week ago, I unlocked bootloader, tried to root, but failed.
So I installed a recovery image to the Rezound using the clockwork mod (I believe).
Now, my phone's battery went all the way to 0% and died, and now it won't accept a charge or turn on.
Every once in a while it will turn on, but only for a minute, then shut back down.
One time, I got into ADB and tried "adb reboot" and my phone went into a sort of bootloop, but was still sort of charging.
But now the device isn't recognized and won't do it again.
Can anyone please help me?
yer gonna get bopped for not using the search function!
Anyway, this should get you started...
Flash AmonRa. Clockwork has issues around charging if the battery goes completely dead.
thatsricci said:
yer gonna get bopped for not using the search function!
Anyway, this should get you started...
Flash AmonRa. Clockwork has issues around charging if the battery goes completely dead.
Click to expand...
Click to collapse
I know...but the thing is...it's dead. Can't flash if it has a dead battery. I don't know where to get another battery.
QuintonS said:
I know...but the thing is...it's dead. Can't flash if it has a dead battery. I don't know where to get another battery.
Click to expand...
Click to collapse
You should have searched more before flashing anything on your phone ... Clockwork mod has this problem... So this sucks for u.... But I'll try and help.... Go buy another battery from Verizon or online... Or take a battery out of a friends phone and flash amonra... Or u can try and take out the battery plug the phone in and get to hboot menu and flash amonra there
Sent from my Dinc... I mean Rezound
Hey guys i've a problem with my x10
So one night i was playing with it than the other day the phone would start
so i thought yeah right might be the battery or something. i took it to my friends x10 it was with 87% charged so i exclude this
Than i tried to flash with flashtool a new kernel and i get stuck at 9% or 15% depending on the kernel i use.
With SEUS it starts to repair but it says. No new updates avaiable after a few moments.
Some information regarding my phone
Unlocked Bootloader
FXP KERNEL
MM TEAM MIUI V4
The phone vibrate but doesn't start or load the kernel.
What do i do?!
Srry for my bad english
Thx in advance
Usrle flashtool to reflash kernel or firmware.
already did but i get stuck at 9% or 15% flashing the kernel
I'm downloading a full generic rom x10a
having similar problem
Hi, I had similar problem as well
X10i running FXP CM7 suddenly just wont boot n charge after I turn off the phone
it wont boot after flashing anything (firm or kernel) except the official firm
now that I end up with a cap R bootloader but flashtool claim that bootloader is rooted
do I still keep the bootloader unlock?
i guess you have a locked bootloader since the original firmware is loading just fine even tho rooting has nothing to do with the bootloader it self. i'm only guessing.
I'm stuck at. Flashing Loader
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
[XBOCT]™ said:
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
Click to expand...
Click to collapse
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
same problem repeat
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
mooving said:
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
Click to expand...
Click to collapse
i'm using
X10a_2.1update1_r2.1.A.0.435_Generic.ftf
And it get stuck at Flashing loader
Idk but i can "read" the kernel when i dump the propriets but i can't "right" when i try to flash something
Anyone?
guys?
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
LJE said:
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
Click to expand...
Click to collapse
maybe i'm wrong idk maybe is a soft brick. thats why i'm asking for some help.
almomdegal said:
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
Click to expand...
Click to collapse
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Try wotanserver's flashtool...
http://www.wotanserver.com/en/
Good luck
SysGhost said:
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Click to expand...
Click to collapse
Didn't work, i even use my friends battery to flash it and it didn't work
almomdegal said:
Didn't work, i even use my friends battery to flash it and it didn't work
Click to expand...
Click to collapse
Well, if the battery issue was fixed, and you're sure the battery is fully charged, then try this: (Quoting from my other post)
I've charged/replaced the battery, and are having trouble with starting up. Earlier flash failed. Now what?
Don't worry. It's pretty darn hard to truly brick this device. Even if the screen remains black, there's still hope.
Once that the battery issue has been dealt with, you can move on:
Download the latest Flashtool and the proper global firmware (FTF-file) for your device from here:
http://forum.xda-developers.com/show...ight=flashtool
1: Extract/Install the Flashtool to a folder of your liking.
2: Copy the ftf-file to the "firmware" folder in the Flashtool folder you just created above.
3: Start Flashtool. Click the Bolt icon (flash). A Window appear. There, choose "flashmode". Cllick OK.
4: A new window appears. In the list on the left, choose the Generic firmware you downloaded and copied into the "firmware" folder. Should have a similar name as the file itself. (Or manually open the ftf-file from the "..." icon on the top right.)
5: Hit "OK. Follow the instructions you get on the screen:
1 - Unplug the device.
2 - Power off the device. (Unplug and replug the battery to be sure it really off, and not stuck in black screen)
3 - Press the "back" putton, and hold it down while performing the next task.
4 - Plug the device into the computers USB.
Click to expand...
Click to collapse
Forced flashing should now start.
Click to expand...
Click to collapse
time to accept the fact that it is really brick
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
mooving said:
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
Click to expand...
Click to collapse
yeah i guess so.
I just needed this closure i'll send it to service today
I just tried flashing Android Revolution to my phone. I went through the whole set up process. Went to reboot then it went blank. Nothing. I get nothing when I plug it in. The computer doesn't recognize any device attached to it. I've tried removing the battery. If I leave the battery out for an extended period of time, when I place it back in the phone, my camera flash flashes really quick then back to nothing. It's as if the phone is completely dead. When I flashed the rom my battery was at 90%. I've used various roms on different phones and this was the first time I did it to my Galaxy s3 and this is the first time it's ever happened. Talk about frustrating. Any help would be appreciated but I'm not holding my breath. It doesn't look good.
Congratulations!
You're phone is now a piece of brick!
Board failure!
If your phone goes to download mode you can repair it by jtag and if it doesn't power on anyway and it's still under warranty, you can ask them to change your phone or repair that.
Cause there's no way to understand you've installed a custom os
Sent from my GT-I9300 using Tapatalk 2
Recovery? Download mode? . Access able?
lokitsar said:
I just tried flashing Android Revolution to my phone. I went through the whole set up process. Went to reboot then it went blank. Nothing. I get nothing when I plug it in. The computer doesn't recognize any device attached to it. I've tried removing the battery. If I leave the battery out for an extended period of time, when I place it back in the phone, my camera flash flashes really quick then back to nothing. It's as if the phone is completely dead. When I flashed the rom my battery was at 90%. I've used various roms on different phones and this was the first time I did it to my Galaxy s3 and this is the first time it's ever happened. Talk about frustrating. Any help would be appreciated but I'm not holding my breath. It doesn't look good.
Click to expand...
Click to collapse
Charge battery /try another battery first .
Then give details of the problem .
jje
No download mode
No, it won’t go to download mode. I'll try the alternate battery. Thanks for the information guys.
Did you flash the right phone ROM?
Yes
aznflawless said:
Did you flash the right phone ROM?
Click to expand...
Click to collapse
Fairly certain I did but I'm pretty sure it's a moot point now. If I could get any sign of life, I'd use Odin to unbrick and go back to stock. Anyhow for now, it makes a great paper weight.