Related
I have sx56. I ran special edition romv1.2. It unlocked my phone. It was AT&T> I migrated to Cingular. The phone works fine. Cant get on internet. I have read everything here and tried every setting for cingular and t mobile. It will work on t mobile for 1 or 2 minutes connecting to a website and I got some sms messages. But then it wont work again. I think it loses its settings. Is it because of that Auto configuration thing? I am still Pocket PC 2002. If I upgrade to wm2003 will the internet settings work then? I have spoken to every dumb support person at cingular they tried every setting they could think of but it wouldnt connect. I get the 2 arrows going in opposite directions and the world thing spins for a while then goes back to phone icon with no message. t mobile actually had me working but then it keeps losing it. I know there are lots of people still using the sx56 and got it working but I have tried everything and it is making me crazy but I dont want to give up and buy a new phone I really love this phone PLEASE can anyone tell me what is wrong? Thanks so much
Don't know if you ever got the help you were looking for however, Siemens released a while back WM2003 w/ATT (to which it was later pulled, maybe because of licensing). I've got that file, but I've found it on the net as well at the following link:
http://www.wireheadtechnologies.com/sx56/sx56_wm2003_update.exe
The original link that mentioned it was on the ATT/Cingular web site here:
http://forums.cingular.com/cng/board/message?board.id=siemens&message.id=8820
Hope this helps...
G
has anyone come across the problem that when you move to say 3g from gsm or back or you loose signal as your in a bad signal area and then get it back, the phone actually looses the radio says "operation failed" and relocks on to the signal?
mine will sometimes loose the signal need restarting and on the boot screen will show NOGSM when its clearly installed as it worked 20seconds ago. i have tried many types of radio rangeing from 1.07 to 1.41 and all their varients. i am at a loss why my phone just looses it and then forgets it has actually lost it untill i try to make a call or send an sms. no calls or sms's can be received by me whilst the phones done this and it does it a hell of a lot.
sometimes it also just looses the radio half way through a call or data call.
anyone got any ideas?
i have a m3100
IPL 1.04
bootloader 2.10oli
and the XDA live OS installed. however it does it on any OS i have tried so far. and thats alot of them.
Same for me.
Same problem for me.
Often I get the message "operation failed" or "the phone is not ready, wait 15 seconds and try again". Thought it was a problem with the new 1.38 radio, but it seems to be something different.
i also get all those error msg's. i have no idea how to fix it either and no 1 here seems to have a clue either :-(
i Had the same problem with mine it due to hardware i guess. Your phone might have fell down or something then this kind of problem starts I fixed mine by opening my phone up and fixed the arial part properly
torrentulla
is there a guide you follow for that or can you give me any tips to do it myself?
thanks
Smith2001 said:
torrentulla
is there a guide you follow for that or can you give me any tips to do it myself?
thanks
Click to expand...
Click to collapse
I fixed my phone almost the same way as Torrentulla did. I'm my case it seems that something was damaged when I dropped my phone a few weeks back. I discovered that when I pushed at a spot right below the flashlight that the radio kept coming up all the time.
These are the steps I took to repair:
Remove all 4 screws (very small torx) at the back of your hermes
Remove back
Put a little piece of paper on the "pressure" spot
Put your phone back together
Turn it on and enjoy!
I hope you'll manage to fix yours aswell!
Phone sometimes shows No GSM, fails to ring
Hey guys, I posted this in the dead hermes thread, but decided to post it here as it's not really bricked. I think it may be a faulty component or something.
My phone was working fine this morning, then in the afternoon I noticed I would have to try to make a call 3 or 4 times before it would go through, it kept on giving me the error (Can't connect, or something along those lines).
Then, I checked my voicemail and found that I had 10 messages from people who had been trying to get in touch with me, but my phone hadn't been ringing.
The kicker came when I soft reset my phone and all of a sudden No GSM popped up! I soft reset it again, and it was gone, and worked fine for a couple of hours. Now its back to not ringing again.
I flashed radio 1.41.00.10 about a week ago, and have been running fine with no problems since. I haven't flashed any rom's in the past week, and this problem just started yesterday. No new software has been installed (except Pimp my black v0.1).
I don't know a lot about the radio, but I didn't think it could become corrupted during regular use, I thought you could only mess it up when you were flashing the phone. I wonder if there is something wrong with the radio? Could the hardware be faulty? This phone is about 8 months old and hasn't had any problems up to this date.
I'm going to flash radio 1.40.10.0 again and see if that makes a difference, but I'd like to know if anyone has any ideas as to what could be causing this.
Sorry this post was so long,
Thanks
-Kai
it seems i don't have a pressure point on mine as the radio is working as and when it likes. which is not alot
gotta sort it out somehow, will take it apart and see if theres anything obvious.
I have the same problem too, phone sometimes shows NO GSM on startup and sometimes it works. Here's where I posted : http://forum.xda-developers.com/showthread.php?t=306073
Now its not even showing NO GSM it just says: NONE, NONE
Also, I noticed that it will only last about 6 hours on a full charge before the battery is absolutely dead.
I'm beginning to think that it may be my radio 1.41.00.10
It seems strange that all of these people are suddenly having this problem now.
Whats the warranty like on these devices? Is it a 1 years parts and defects warranty? Or is it some ****ty 90 day warranty?
As it is my phone is a piece of garbage, not worth using at all, I am very disapointed in it.
It's a hardware problem.
Hi guys,
I'm experiencing the same problems since two months and I've been struggling with all kind of OS, ROM, RADIO and bootloader, without even gettin close to solve them.
My phone randomly loads the RADIO (otherwise I get the "No Gsm" message), even when loaded, the connection is not suitable and my phone is often unreachable on the net. The battery life is very short because the phone always looses the signal and then seraches till he find it, before loosing it again.
So I disassembled my phone and did a lot of testing with hardware connections. I have found that the motherboard connection with the flash/scroll module isn't stable at all. You can easily move it and find that this affects the phone ability to load the RADIO. It seem strange but it's true. I can't solve the problem and I'm very upset with HTC because of their hardware components lack of quality. I would like to try to change the module to but I can't find a place where i can buy HTC hardware parts.
So I'm going to change my pda, I'll never buy HTC anymore.
Any help?
Has anyone figured out the problem? If it is hardware, what "pressure" spot is it? I tried, but wondered if I'm not in the right place.
In my case it was a spot right below the flash/scroll-part. As said earlier, i put a piece of paper on the spot and reassembled the phone. It still works excellent after a week!
My dopod can't connect to the mobile network as well, but only with the 3 network. It seems fine when being connected to an Optus network. Have you guys tried using a different network simcard?
I'm not sure if mine is a physical problem but maybe a setting which i need to configure so i can connect to a 3 network. Help anyone?
ROM version : Pro BLACK 3.0
ROM date : 01/04/07
Radio version : 1.41.00.10
mine also works just under the flash with the cover off, but if i hold it too hard then the screen goes all white and doesn't work, until i can get the case off its a hit and miss game at the moment.
thanks very much for the tips and help
Dan
Larrys said:
.....
So I'm going to change my pda, I'll never buy HTC anymore.
Click to expand...
Click to collapse
I cannot agree with this more.
I am sick to death of this phone. I had one of the first in the country for normal sales and spent weeks arguing with HTC who flatly denied the screen alignment issue. EVENTUALLY I got them to fix this after referencing posts in this forum.
I continued to suffer the "coma" software issue - why is it so F*((&&^ dificult for a device to wake up when its auto-sleeped?
And finaly, to top it off, I have been suffering this problem. I cannot express how mad I am. Did I buy a cheap phone? NO. I have had nothing but problems with this phone and will NOT buy another HTC.
Oh and if anyone knows how to repair a failed Radio upgrade, please help me! I don't have any choice but to use it until the IMate Ultimates come out.
Due to seeing this radio problem I thought I would try downgrading the radio from 1.4.summint or other (the latest) to a slightly older version. This was of course before I saw this thread. During the downgrade the installer stopped at 15%. Now no matter what I do it sits at the IPL/SPL screen (3 colour bars+white). I have done the obvious i.e. follow the installers error procedure (remove the battery).
Device: HERM200
IPL-1.04
SPL-2.10.Olipro
Please help me be able to use this for another month or two at most - i hope!
Thanks guys
update:
OK Guys
thanks to this thread: http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
I now have it trying to boot the o/s. I get the message "No GSM" on the boot screen but when it boots up it asks me for my pin number and freezes. I guess its locking up because it has no "phone" part? According to the instructions in the other thread I am supposed to flash it again but I can't as the phone locks on boot.....
Any ideas?
*FINALY* got it back into pre-flash feck up situation. Sadly, this still leaves me with the hardware problem. HTC can go poke themselves until the cows come home. Im taking my money somewhere else.
i installed the XDA Windows mobile 6 about 3-4 months ago on my SPV M3100,
everything worked fine untill just lately it started displaying just a plain white screen, not bricked because if i rapped on the power button a few times it would display everything normally?
problem is it has started doing it more and more often untill lately it decided to completely go white - i found out the phone still works just a blank screen? also some of the mounted buttons stopped working at times and would work othertimes?
ive fully charged it, turned it on and plugged it into my pc but im not sure what to do?
is it something to do with XDA, maybe some kind of virus or should i literally re-install the orange windows mobile 5 and send it back?
any help would be great! - im in a bit of a pickle here
thanks -Edd
wm6 spv m3100 white screen
hi there
if anyone is following this thread, i too upgraded first to 4.01 as good as gold, then to 4.30, Schaps ROM's. all fine but then the white screens started in 4.3, in the end about 10-14 days i had to remove the battery to boot the unit, and only thrn with PSU/USB plugged in, so power issue?
anyway i pushed thorugh to 4.31 alls currently well, keep you posted
cheers in all others senses great work all round
cheers pete
Yep, I've got this issue with my HTC Hermes but it only manifested itself after the upgrade to WM6?!
Can you ALL please tell us what bootloader you are running?
I followed the online instructions for getting Schaps WM6 ROM on board for my SPV. I shall dig them out.
mrvanx said:
Can you ALL please tell us what bootloader you are running?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=352857
Hi Folks
My Hermes/Tytn is an Orange M3100. Recently it has begun dropping calls, or rather, ignoring them. The caller could hear a ringing tone but the phone wouldn't switch on, show me an incomming call or anything. A short while later, usually after I'd switched it on (I mean, the screen, "off" is that it's on standby) I'd get the notification of a missed call. More often than not it would come through after I had made a call.
This reached a "point" on the weekend where I missed about 17 calls from the Agency to get work for me as I was the only one available
So. I upgraded as reccomended on here. Up to HardSPL 2.10, Radio version 1.41 and then upgraded to Schaps 4.22 WM6 Rom.
Now, I made sure that ActiveSync has connected and synchronised, and all my contacts and PIM info is in Outlook. However, A/S won't transmit the information to the PDA, even though it tells me it's synchronising.
The only way I have managed to get my PIM data/address book back onto the PDA was by running a custom SPB backup file to restore the calender, sms and phonebook.
This is where the fun starts. My PIM and Tasks then go "read only" merely by having a warning telling me I have no memory and to go and close other programs down. But there isn't anything else running!
Fine. Right. Ok. Obviously I've done something wrong. I did a hard reset this evening. It wiped all the data internally and reset it. I changed the details to match the username that was already stored in A/S and plugged it in.
It tells me "Connecting" and the green thing swirls around but doesn't actually do anything.
I have heard mention of the MTTY software, so I've got that here. But it won't allow me to connect on USB, only Com1, 2 or 3.
So I've a pretty useless phone at the moment. It's got none of my files on there, the satnav is rendered useless merely because I can't install the sod and all the other problems to go with it.
Short of screaming abuse at it and throwing it across the room I'm a bit stuffed. And I can't spend anymore time on it as I've got to be getting up for work at 4am (only finished tonight at 8pm ) for another full day
I've read the wiki, I've gone through the pages and pages and, er, pages of posts but I'm hitting a brick wall somewhere. I'm not as bright as you guys, but I get by.
TIA. Elwyn
Click to expand...
Click to collapse
The device is no longer worthwhile for me and have spoken to Mike Channon over it. If you can change that or help me change it I would be grateful
Mikechannon is the main man when it comes to the hardware side of things, if it was an early bootloader issue (related to bad NAND blocks) then thats what i was questioning your SPL version about.
If mike is confident it is the hardware problem then id take his word for it, the guy rocks
/me has to get his mikechannon ass kissing back into shape again hehe.
mrvanx said:
Mikechannon is the main man when it comes to the hardware side of things, if it was an early bootloader issue (related to bad NAND blocks) then thats what i was questioning your SPL version about.
If mike is confident it is the hardware problem then id take his word for it, the guy rocks
/me has to get his mikechannon ass kissing back into shape again hehe.
Click to expand...
Click to collapse
Not entirely sure what it is yet. If WM6 wrote to the 'wrong' part of the memory, would reflashing back to WM5 fix this?! Is there a way of repairing NAND issues?
MrVanx, I looked in the original thread that I posted in about this issue and followed you're link. Not sure whether I did or didn't at the time, but I can see there are instructions for downgrading the ROM from 6 to 5. However I am now in the situation that I can't use the USB cable as it causes it to white screen, but probably could if I did it via memory card....
white screen continued
hi there
sorry about lack of info i installed olipro 1.4 as per the instructions at the wiki i think. mine doesnt boot white, it turns white/fades to white when in use, or more commoinly i will press off after use, then later turn the unit on, and it will come white. first few times it si normal after 2nd on/off, then it stops completly requiring a hard boot, then that stops and it requires a battery off, then that stops. however it always seems to repsond when power connected, even if 100% charged or just off.
it feels to me like a power issue, still there in 4.31, wasnt there in 4.01, going back now to see if its hardware.
i will give as much info as you guys need, i got my phone from orange in may 2007
pete
white screen update
hello again
still on 4.31 activesync isnt playing at teh moment but anyway.
on the screen thing, if i leave the unit standby itself and then power back on it seems fine, so far 3 hours of good, no white screens.
thanks pete
hi there i face this problem with my imate jasjam sorry to tell you that but this problem is a hardware problem you be confirm that it hardware by push by your 2 fingers below the screen and above the keys like you catch"hold" something bush the power key again the white screen will be disappear .sorry if you don't understand me because of my English.
Hi everybody.
Anybody solved problem with white screen?
I have the same truble as EddTQ - White blank screen & also some of the mounted buttons stopped working rarely 2 week before white blank.
same problem here.
Maybe a radio problem?
Folks,
The problem you are describing sounds like the flex connector.
http://forum.xda-developers.com/showthread.php?t=321163&highlight=white+screen
This thread should give you some details. I had the same problem but phoned Orange who sent me out a new one in 9 hours!
exactly
What happes is exactly the problem explained by alkizmo ...
thanks.
Have HardSPL installed on phone. Got phone on eBay - has very few hours. Came with a Rom that displayed TEST ONLY which was WM5. GSM radio worked, Bluetooth worked and Wifi worked. Tried installing shipped HTC WM6 Rom - did it through ActiveSync - should have used MSD card. - Rom installed though everything was ok but didn't install a SIM card to test phone - used it as PDA and WIFI for a week no freezes. Now this morning wanted to switch phones over and inserted SIM - saw NO GSM on boot - never really noticed it before.
Checked in ABOUT section to see if a radio was loaded - comes up blank. Read some things about NO GSM errors - got a little nervous - so I thought I'd reflash entire ROM tonight with SD.
Followed directions and get into update process and it seems to freeze at GSM with progress bar at about 15% - for about 30 minutes.
Removed battery and it boots to TRICOLOR. (I freeked out at this point)
Put a HardSPLv7 on SD card and did the above - update was successful
Phone boots up to OS still with no GSM
Tried the update process again with the same ROM - still has problems and never gets past the same point as before. Will try another ROM but I'm a little doubtful. If I can recover it back again will try just upgrading radio to see if it makes a difference.
ANY SUGGESTIONS or is the hardware fried?
Thanks.
OK, think it may be back and I was able to reflash using a wm6 stock HTC ROM. Think either my original flash of the same ROM was bad - downloaded a new file and flashed with the SD - originally did it via ActiveSync.
To get it to work I did a couple of hardspl reflashes and got into the OS. DID a couple of hard resets and magically GSM appeared. Turned phone off and then NO GSM appeared again. Did the hard reset again - came back. Not taking anything for granted put in a SD card and reflashed. Held my breath and for some reason it did a complete flash and never really hung up for more than a minute or two. Soft reset - GSM was there. Turned phone off and on a few times and its still there. Phone now finds the GSM radio much faster than before. Can make and receive calls (does wake out of sleep) - signal strength is same on my other Cingular 2125. Will try out tomorrow and see how it goes. Either the reflash does it or something is loose in the hardware but if it works a few hours tonight it should be good.
Will be a little hesitant to reflash after this but will see after a stress test.
Hold both softkeys and hold the power button
You can also hold both softkeys and put the stylus into the reset hole. Tell me if that works.
Initially no. When I attempted to flash the HTC Factory Rom it froze. Prior to that I did a couple of hard resets using the two softkeys and reset pin. With the resets couldn't get the GSM radio to turn on. Tried the ROM flash but it froze (about 1/10 of the way) - so I basically OS bricked it by removing the battery when it was at this stage. Got to the bootloader screen. Tried to flash OS again with SD card - still froze. SO I thought reflash HardSPL and the OS magically appeared and did the steps above.
After a couple of hours - call made, turned off and restarted device no problems still have GSM radio. Can receive a call when in standby. May try to do another hard reset and see if it still works after a day or so of testing phone but I want to try it for a few days by turning it on and off and making and receiving calls. If I can do another hard reset and everything works I think it was just a bad initial flash through ActiveSync. May get bold and flash another ROM as a test.
Since the phone worked with the TEST OS when I got it I think the only factor is the WM6 flash that I did. More than likely the hardware is OK but only time will tell.
I don't believe you will recover your radio rom now as you interrupted the flash. It generally takes 30 MINUTES to flash a complete rom. You stopped it during the radio rom flash, BIG MISTAKE....
If you can find the SHIPPED STOCK ROM or the original radio rom then you might have a small chance at recovery, we're talking about you winning the lottery 10 times in a row chance...
If you try to flash anything but the original radio rom then you can kiss the phone functionality goodbye....
Good luck finding the right roms...
Cheers...
Its not bricked. In my post said I did a full recovery and its working with the stock HTC WM6 ROM with the HTC radio. I can receive and make calls. Able to ActiveSync with the PC and have hard reset a few times just to make sure all is well. I believe there is still a hardware problem - either a loose connection inside or something else is going on but I think its definately hardware. When the stylus is out of the holder EVERYTHING works fine - have a signal - can sync - can charge it - no issues. If I put the stylus in part way no problem - push it in all the way during a call it will still say connected yet will hear nothing and can't disconnect. Pressing end has no effect yet the phone will still function - just the in call symbol stays and the green led still flashes.
Turn it fully off and back on with stylus out - shows GSM radio code and phone will now work.
Have to check the service manual to see if the stylus holder when the stylus is inserted pushes on anything vital. Can't imagine thats it. But so far with the stylus out everything is ok. Will attempt to use it tomorrow see if thats it.
Know it sounds stupid but thats what I'm observing so far. Its late here see what happens tomorrow
Thing is running and can use the phone (no static, three bars) but last night had a few no GSM messages during a cold boot. Ran it all night and it seems to be working - booted a couple of times, charged it, sync'd it and actually put the stylus in (don't know if thats the problem) and still working. May be a loose connection that is currently ok but who knows when it will stop working. Other possibility is heat or a failing radio. Could also be battery but thats doubtful. Could have messed up the stack during the initial flash so I'll see over the next few days. This one is starting to drive me a little crazy because it works then for no reason it will stop then resume after a hard reset or reset. Could also just be the version of the ROM I'm using but it came from the repository on XDA-Developers. Just rebooted it when I was typing this and it still finds GSM radio.
Tried it for a day and I think the radio is fried. Started out finding GSM then when driving around with my Bluetooth heard a bleep which indicates loss of signal - saw it hunting then it finds the signal. During a call for about 3 minutes just drops call and on the screen the dialer won't let you disconnect the call.
Rebooted got the NO GSM message - eventually found it - briefly then NO GSM again.
Tonight opened it up and reseated and cleaned motherboard contacts including radio. After hard reset got GSM again - briefly. Then no GSM
Tried upgrading and downgrading radio via SD card - no go would only hang up Tried complete with OS - same thing. Tried through ActiveSync method SSPL and got same.
So I think the phone is pretty much not really a phone - can still boot into OS. May try some more but I think its definately a motherboard issue. Shouldn't be that hard to flash and the GSM should at least be stable.
When I bought it on eBay and first turned it on saw a TEST ONLY message on boot with a WM5 Rom. The seller was a little vague just said it freezes sometimes. Got it cheaply thankfully so I'll keep hunting around for another unless someone has a suggestion?
The Radio seems to be the touchiest part of the Hermes. When it fails theres nothing that seems to be able to fix it. Look for another cheap Hermes. At the very least you will have spare parts.
how weird is this I have just gone through just the same problem and took a day to sort it out . ok here is what I did in the end . now what you need is any official rom pref wm5 . I can send you a link if needed to the one I used ... now try flash it from the pc it will stop at 12 percent ....... now take battery out and boot in bootloader mode .... now flash any rom that's wm6 etc .... devise will restart .... now take battery out and re boot it may take two or three boots to get it working prop without the no gsm error but trust me it will boot . when its booted up flash the original wm5 shipped rom run through the rom sequence and when its waiting to flash saying zero percent manualy put your phone in bootloader and wait 30 odd min tadaaaaa phone is now perfect ... now flash any rom you like as the radio is fixed . its something to do with the 12 percent bit it hangs on .??!!! sorry its long and complicated but I have my hermes back to life through doing it ................... let me know how you get on bud. if needed 07832999919 uk . so its 0447832999919 oh I have hard spl 1.40 spl 1.1 or something lol can't remember . anyway good luck
Ok, think I initially really messed up my flash and the WM6 which was the official HTC version may have been corrupted but showed full flash. When I tried again I would also get the 12% even with a SD flash. So I tried flashing just a RADIO ROM which did complete. The NO GSM message still would pop up maybe 50% and not necessarily everytime.
When to MTTY.EXE and did a bad block check - no problems
In MTTY did a FORMAT/CLEAR.
Left everything alone and again reflashed just the RADIO - things seemed to be better - less NO GSM.
Tonight - just before you posted I successfully did a complete reflash with the HTC WM6 rom with Radio 1.48. Very surprised it worked this time - no hangups except during the GSM part which only stopped a minute or two.
Complete reflash in about 10-12 minutes with the SD card method.
SO far things are working - tried a reboot a few times and now radio is found every try. Will try for a few hours and try again tomorrow.
What I did have is a white screen/with image once - it was cleared by just pressing briefly the power button. So it may be heat related - don't know.
Keep me posted in this thread whats going on and I'll do the same.
What ROM WM5 did you flash to get yours to work?
Spoke too soon! Put in a sim card - powered up and it worked. Tried making test call and it worked. Tried again and it showed dialer and dialing and never connected. Could not use the dialer to hang up. Also showed drop in network. Tried turning phone radio off in dialer and back on - showed !X. With the phone off hook image at the top bar. Tried again - same thing. Expected to see no GSM when power cycled and it did show NO GSM.
Right now its working even after a few power cycles but honestly I think the successful flashes may be due to the GSM radio being found. If it doesn't find the radio and you attempt to flash thats why it hangs. If you phone works for a few days or day I'd be very surprised. The real test is to try it when moving from tower location to tower location. Thats where I noticed the radio was acting up. With a bluetooth headset it will beep indicating a drop in carrier. When its doing this the radio isn't working properly and can't lock on to a signal
If your phone does work PLEASE post what you did and what files were flashed.
For my phone I think its heat related. Possibly the heat from the circuitry is opening up or stressing out a component causing it to fail. I really think my motherboard is faulty and reading on the HERMES this isn't that uncommon. Being that the phone has so little hours I think it must have been a return or factory reject.
More than likely I'll have to purchase another phone needing a screen or one thats in poor shape to salvage the motherboard and attempt to put it in my case since the housing and screen are pristine with little to no use. I've been told that any 8525 motherboard will work but I doubt it since the Dpad is different and I have a front video camera.
No, ANY Hermes mainboard will work... Hermes are identical internally, even the 8525 is able to use the front camera, it just isn't included in that model.
Cheers...
Thanks, makes my life easier!
ok mate i used htc orig rom by orange uk google the words,,,, orange spv m3100 update ummm ok hang on il grab the link for you ...
http://www.orange.co.uk/business/downloads/SPV_M3100_ROMUpdate_1007.exe then flash hard spl then update your rom to whatever you like ,,, hope this helps buddy
Might try it tonight but I really think I need a new mainboard. I am able to flash only when it finds the GSM and I think any hangups are due to the GSM radio circuity failing or some strange power flux on the motherboard. I am having strange multiple freezes/slowdowns as well as NO GSM errors. Tried a WM5 and WM6 specific for my HERM200 and no change. When it works it will work and make and receive calls but after a while without a load but under load - multiple calls, running excel or other things the radio will drop or it will attempt a call, not connect and will not let me hang up. No software update will fix this issue - it has to be hardware.
If I have successfully done base HTC ROM flashes - complete with radio phone should theoretically work. I have to face reality with this one which although looks pristine is a lemon and have to buy a working beat up 8525 and try the motherboard as long as the seller assures that the phone can make and receive calls without problems.
Also have other issues with screen fadeout which I know is tied to the dPad controller - but I can live with that for a while and I have a source for a part replacement and can try a quick fix to verify its just the dPad.
You got lucky so far - but if you try to use the phone all day running multiple programs or CPU intensive tasks your radio still may fail. You could also try upgrading the ROM again to something that is MFG and see if it takes.
It is possible to flash the OS without flashing the radio, It will be a cooked rom but they're better in most respects than a stock rom. Faster, leaner with all the bloatware removed.
No software change is going to fix this. Its not a software bug its a flaw in the hardware. Can't flash a radio Rom - thats a chip problem. Its basically a low level format and write to eprom. Thats pretty basic. Also making and receiving calls is also pretty basic. The dialer has been around for a while and is pretty stable.
My touch screen will not work at all, everything else on the phone works just fine. I tried a hard reset and now I am stuck at the alignment screen. Any suggestions.. Anyone run across this error?
Thanks
reflash bro
put the stock rom back on
and then put the modded rom on
and it should be fine
Typically means something is interfering with the recognizer.
If you are using a protective case (shell) or screen protector, try removing them temporarily to see if they may be causing your problem.
I didn't have anything over the screen.. Any idea why it would do something like that?? I'm going to reflash to stock and back to modded ROM tonight and I'll let you guys know in the morning.. Thanks for your help.
Could be a "bad" flash.
If it still happens with the stock ROM flash, you may have a defective unit on your hands.
Hardware problem?
I had the exact same problem about a week ago. I tried reflashing the device, hard reset, etc. In the end, I couldn't even get past the screen calibration wizard. My conclusion was that I had some kind of harware problem -- the touch screen would respond intermittently for brief periods of time and then go unresponsive again.
My fix: I took the phone to my ATT service center who, much to my gleeful surprise, gave me a new one (warranty exchange) without any hassle. I expected to have to fight with them, but the transaction was trivial and stress-free.
I'm now deciding which WM 6.5 ROM I like the best. Many thanks to all the hard-working contributors and chefs on XDA for providing such awesome content and support!
Good Luck with your phone
i also had this problem recently. phone was working fine in the night, went to bed and woke up and was unresponsive. Tried everything. I ended up flashing back to all the stock stuff and sent it in for repairs. I got the screen and dpad replaced under warranty. I have no idea what caused it, but it happened. Definately not a software issue if you have reflashed...
my advise, flash back to stock spl and your carrier rom and send it back.
I had a similar problem and opened a thread as well. My problem in chronological order
1. Bought a TMobile MDA IV over ebay.
2. Flashed several different ROMs of WM6.1 and was just enjoying myself.
3. Installed a 6.5 ROM the calibration screen required me to go through 3 full circles.
4. Worked fine for a day, then the device was locked and watever I tried I just couldnt get to open it up
5. Did softreset, it didnt help either. I Would end up at lock screen
6. Finally got back to HTC stock ROM 6.1, and I couldnt get past the calibration screen for a month.
7. My conclusion as well, that its a hardware problem, unfortunatel where I live I dont have Tmobile and the screen from touch pro is slightly different in size to the tmobile variant.
8. Hence it was a brick!!!!
9. After a month just last week, I thought of trying to flash back to 6.5 and see if it works.
10. Went calibrating in circles for about 10 times and guess wat!!!! It starts up!!!!
Now my conclusions are as good as anyones, it cant be an hardware issue. I am trying to find a solution so I can reflash my ROM and go to a stable version and live with my phone atleast for an year.
The Mystic ROM lite version has touch response software built in, Could this be the issue.
Anyones got any idea let me know