Today i downloaded hspl 4 for my hd2 that was running rom 3.14 and has spl 3.03
then i tried to install magldr 1.13 but after the installation my phone has not been able to start it is stuck on the boot screen
I found out that spl 3.03 and hspl 4 isn't compatible with magldr 1.13
how do i reset it? I've already tried to do a hard reset but it didn't work
please help!!
jing92 said:
Today i downloaded hspl 4 for my hd2 that was running rom 3.14 and has spl 3.03
then i tried to install magldr 1.13 but after the installation my phone has not been able to start it is stuck on the boot screen
I found out that spl 3.03 and hspl 4 isn't compatible with magldr 1.13
how do i reset it? I've already tried to do a hard reset but it didn't work
please help!!
Click to expand...
Click to collapse
bootloader - run hspl4 - choose 2.08.hspl
got the same problem
hiya i have the same problem phone is stuck on htc screen and when i reload hspl4 to change it to 2.08 it wont load because it cant make usb connection any ideas?
dont worry found bootloader instructions and it worked
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.
Related
When I try and reflash the ROM it gets to 1% and says Vendor ID error
spl 1.11 only boot in tricolor screen
My laptop went into hibernate (hard button pressed accidently) 33% of the way through the standard ROM upgrade of the latest 3.3.1 (SPL.1.11).
Now it will only boot into tricolour screen with SPL-1.11 and IPL-1.00
When I try and reflash the ROM it gets to 1% and says Vendor ID error
Everything else just wont conect.
From the forums this seems to be a true brick!! Am I right or is there another way (I dont have KITPL enabled on the ROM).
Thanks for any help
Try reading some more, AND post in the appropriate place!
http://forum.xda-developers.com/showthread.php?t=286755
Dear All,
While I am upgrading TNT to my Dopod 838 Pro without using PC(USB Cable),
I renamed nbh file to HERMIMG.nbh and run SSPL-HERM file in freshly formatted SD card.First it upgrade properly until 100% .After that not booting automatically stuck in 100% .I press reset button and boot TNT screen , after TNT screen only white screen appear, boot nothing.I and stucking in this stage. I tried to load boot loader mood.But I don't know exactly which keys to press to bring boot loader mood in Dopod838Pro.
Kindly guide me what should I do to bring back normal.
Before upgrading my Rom is
Schaps WM6 Pro 4.01 with extension Rom
Dopod838Pro
Radio:1.54.30.10
Thanks in advance
sein said:
Dear All,
While I am upgrading TNT to my Dopod 838 Pro without using PC(USB Cable),
I renamed nbh file to HERMIMG.nbh and run SSPL-HERM file in freshly formatted SD card.First it upgrade properly until 100% .After that not booting automatically stuck in 100% .I press reset button and boot TNT screen , after TNT screen only white screen appear, boot nothing.I and stucking in this stage. I tried to load boot loader mood.But I don't know exactly which keys to press to bring boot loader mood in Dopod838Pro.
Kindly guide me what should I do to bring back normal.
Before upgrading my Rom is
Schaps WM6 Pro 4.01 with extension Rom
Dopod838Pro
Radio:1.54.30.10
Thanks in advance
Click to expand...
Click to collapse
Are you "Hardspl"? (olipro 2.10 for example?)
In this case you do not have to launch SSPL. Just do what i describe here: http://forum.xda-developers.com/showthread.php?t=352004
Bergerac56 said:
Are you "Hardspl"? (olipro 2.10 for example?)
In this case you do not have to launch SSPL. Just do what i describe here: http://forum.xda-developers.com/showthread.php?t=352004
Click to expand...
Click to collapse
Yes Hard SPL 2.6 - Thanks
I've successfully upgraded by using your guide - Thanks again
I FOLLOWED all instructions for upgrade ROM and RADIO? Can one of you experts HELP? my titan keeps on rebooting and rebooting, it will not stop rebooting, PLEASEEEEEEEEEEEEEE HELP WITH INSTRUCTIONS ON HOW TO MAKE IT STOP REBOOTING.
It sounds like you might have a mismatched bootloader and ROM.
Hold down power and camera buttons while resetting. This will put you into the bootloader. What version is it?
If I am correct, IMHO the easiest way out is to load a ROM that matches your bootloader and then you will be able to connect via Active Sync once again. At that point you can start over.
Looks like JohnW on PPCGeeks had a better suggestion to upgrade the bootloader:
"Trick to load this SPL in is to
Hard reset your phone
Boot to the Wellcome screen BUT do not tap your screen
At this stage plug in your phone into your PC and apply the SPL unlocker."
Hey
I tried flashing my rom to 1.66 from the MicroSD, but something has gone wrong and now my phone will not boot at all. I've tried taking the microSD card out of the phone but it still wont boot, it just shows a triangle with an exclamation mark! Please help!
Many Thanks
put the SD inside the phone again, push the red bottom to reset the phone and keep the vol down pressed and try to flash again..
Did you install HSPL?
If so, don't install HTC Official ROM's from SD card unless:
1) the ROM is for you region/operator (CID)
2) you're using a gold card to flash (I think)
Flashing official ROM's from MicroSD will overwrite the HSPL with the normal HTC SPL. With the regular SPL in place, the ROM you flash has to be for your region/operator, or it won't flash/boot normally.
Solution: reflash HSPL, and install the 1.66 ROM over USB (the HSPL doesn't allow itself to be overwritten over USB, if I remember correctly).
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
try a hard reset. turn the phone off, hold down both volume buttons, and turn the phone on, keeping the vol buttons held down. then when prompted,press vol up to reset it.
yes, you'll lose any data and modifications on your phone, it will be back to how it was right after you flashed it, but at least it will start up. better than how it is now, right?
nishankyadav said:
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
Click to expand...
Click to collapse
What an utterly unfortunate situation!! Couple of questions/remarks:
1. Did you install HTC 3.14 ROM with your S/N from HTC's website before flashing Artemis?
2. You already removed HSPL, so I would advice to extract the 3.14 RUU file to your desktop and copy the custom.nbh file to your SD Card after having it renamed to leoimg.nbh (insert SD CArd into PC to do that).
3. Reinsert SD card in device and enter bootlader mode and the installation of 3.14 should start automatically.
4. After that download Artemis 43 and extract it to the folder where you're SSPL_RUU,exe resides. Bothe the custom.nbh and the SSPL file must be in the same folder!
6. Start SSPL_RUU and flash Artemis
7. After that first a hard reset and then a soft reset.
Also read page 1 - Flashing notes
This should to it for you,
regards, Kuzibri
P.S. I posted this also in Artemis thread
same problem
i've got the same problem, but i didn't install the rom artemis,
i restart the installation many time but i've got always the same problem
the display showing loading..... please wait with the chucky logo.
someone can help me???????
thank you