hello,
I have question, Anyone boot tg01 to debug mode?
I launched debug mode yesterday but I can't repeat it. It happed when I make hard reset after install mirom1.
drago1 said:
hello,
I have question, Anyone boot tg01 to debug mode?
I launched debug mode yesterday but I can't repeat it. It happed when I make hard reset after install mirom1.
Click to expand...
Click to collapse
TG01 debug modes, this is dependant on the rom you have on your device, most TG01 roms can use these power on key combinations to get debug information.
Power on holding down camera key, this will lead to a white screen stating TEST MODE 3G TG01W, you can use camera button and volume up and down to print characters at bottom of screen
Debug Mode
Hit reset button on back of device under battery cover, while holding down camera button and volume DOWN button. Once you have chosen an option below, and saved your choice, you will be able to use the power button, volume down and camera combination to bring up debug mode until you choose option 3 which disables the option again until you use the reset button combination mentioned above.
You will get 3 options:
0:TSA Only
1:TSA+UART
2:A+UART+QXDM
3:None
Use volume up/down to select mode and press camera key to save then power on.
A very recent version of QXDM can be downloaded form here
Drivers reported to be working for the TG01 are attached below
A brief explanation of what QXDM is can be found here
Some screenshots of QXDM (taken from Qualcomm website)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
what exactly is 'debug mode' ?
olyloh6696 said:
what exactly is 'debug mode' ?
Click to expand...
Click to collapse
Must be system diagnostics and debugging, but special software would be required, QXDM being one i found. I do not have my usb cable handy to try it though.
(InsertNameHere) said:
Must be system diagnostics and debugging, but special software would be required, QXDM being one i found. I do not have my usb cable handy to try it though.
Click to expand...
Click to collapse
thanks for the explanation
what exactly is it required for, and how is it helpful?
olyloh6696 said:
thanks for the explanation
what exactly is it required for, and how is it helpful?
Click to expand...
Click to collapse
QXDM could be used to test radio performance for example, however i don't know much about the debug mode to be honest, i just answered the OP's question.
To turn TG01 in TestMode, it's OK, but i don't have this usb driver for QXDM. you have this driver?
chdeul said:
To turn TG01 in TestMode, it's OK, but i don't have this usb driver for QXDM. you have this driver?
Click to expand...
Click to collapse
Plug phone to pc and wait for drivers to install, then restart phone in debug mode and wait for drivers to install, does that work?
Or if that doesn't work for you, try activesync, there are no special drivers needed. Just TG01 modem driver.
Doesn't work.
Active Sync work in normal mode. In test mode, my windows would the qualcomm cdma technologie MSM driver. i install this driver but don't work.
I don't find the correct driver for test mode.
Sorry for my poor english.
chdeul said:
Doesn't work.
Active Sync work in normal mode. In test mode, my windows would the qualcomm cdma technologie MSM driver. i install this driver but don't work.
I don't find the correct driver for test mode.
Sorry for my poor english.
Click to expand...
Click to collapse
Try getting your phone to work as a modem first. That should install the modem drivers you need.
Connect via your USB cable, then go Start/Programs/Internet Sharing. Set the upper box to USB and the lower to whichever cell connection you are using, then just hit the 'Connect' soft key. First time, your PC will load the necessary drivers, to it will take some time, but once done, it will show 'Connected' on the mobile's screen.
I tried several roms for testing the debug mode:
no debugmode or other keys to press at boot:
miROM8 [GER] 20.10. RADIO (5005.1800.05)
miROM8 [GER] 01.04.11 RADIO (0300)
miROM8 [GER] 01.04.11 RADIO (5005.1700.05)
debugmode ok at booting:
miROM1_rel. 5 [GER] RADIO (5007.0000.0321)
miROM1_rel. 6 [ENG] RADIO (5007.0000.0321)
miROM8 [GER] 01.04.11 RADIO (5007.0000.0321)
...seems that the radioversion is responsible for this feature.
I also tried serveral drivers...HTC Diag Driver is working, if u add the tg01-ids:
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_00
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_01
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_02
At boot I can switch to the debugmenu (reset button while holding down camera and volume DOWN button). Then I can choose 0-9,A,B,C,D...Z !!!
The camerabutton stores my option and switchs to the 2nd place. So I can choose an 2./3./4./.... option. With the "Z-option" I can delete all settings.
But if I store something with camerakey, exit with powerkey, I cant (!) switch the debugmode unter windows :-(
I tried Power on holding down camera key / Power on holding down camera key + volume DOWN / dial ##3424# or something else....
Perhaps I have a "bad" rom? Any idear?
Hello,
do that by using QxDM could have screwed up the cooker with the radio 0321?
Leaving screens appear:
MOD CM 00000
MOD GDI 00000
MOD MM 00000
MOD TMC 00000 (+ White LED) ...
Can you upload yours modified drivers for Debugmode? Thnaks in advance.
americo1 said:
Hello,
do that by using QxDM could have screwed up the cooker with the radio 0321?
Leaving screens appear:
MOD CM 00000
MOD GDI 00000
MOD MM 00000
MOD TMC 00000 (+ White LED) ...
Click to expand...
Click to collapse
You don't need to use debug mode or QXDM to see these modes in any rom cooked using Feraponts new kitchen templates
chdeul said:
Can you upload yours modified drivers for Debugmode? Thnaks in advance.
Click to expand...
Click to collapse
Yes, good idea
played with my tg01 :
Booting normal : Driver "Windows Mobile-based Devie" (USB\VID_0930&PID_0D57)
Power On + Hold Vol UP : Boots Win (somethimes hangs), Driver "USBDBG KITL for MSM7200A WM7" (USB\VID_045E&PID_0301), goole for "USB RNDIS Function Driver"
Power On + Hold Vol Down : FW Flash (caution, if u have a flashfile on your SD...you cant abort this!!!)
Power On + Hold Camera : black screen, white LED, Driver "Toshiba DL" (USB\VID_0930&PID_0D80), Driver can be found in TG-Downloader
Power On + Hold Vol Up + Hold Camera : Master Clear / Factory Settings (you can abort this later)
Power On + Hold Vol Down + Hold Camera : Test Mode Screen, Driver (USB\VID_05C6&PID_3200&MI_00, USB\VID_05C6&PID_3200&MI_01, USB\VID_05C6&PID_3200&MI_02), HTCDiagDrivers?
i used the drivers from http://forum.xda-developers.com/showthread.php?t=697487 and added under "[models]" in htcdiag.inf these 3 lines :
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_00
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_01
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_02
...dont know, if this is working. The XP-Devicemanager says, that everything is fine.
lonelysurfer said:
i used the drivers from http://forum.xda-developers.com/showthread.php?t=697487 and added under "[models]" in htcdiag.inf these 3 lines :
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_00
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_01
%OEMDevice02% = OEMPort02, USB\VID_05C6&PID_3200&MI_02
...dont know, if this is working. The XP-Devicemanager says, that everything is fine.
Click to expand...
Click to collapse
I have attached drivers with the vendor ids added in post 2
Or get them from here
Update: Power On + Hold Vol UP : Boots not Win, Driver "USBDBG KITL for MSM7200A WM7" (USB\VID_045E&PID_0301), goole for "USB RNDIS Function Driver"
TG01 with USB RNDIS Function Driver and fixed IP (in my case 192.168.178.110):
Portscan:
Port 135 Open (epmap)
Port 139 Open (netbios-ssn)
Port 445 Open (microsoft-ds)
Port 990 Open (stun-p1)
Port 1028 Open : HTTP
Port 1070 Open : HTTP
Port 1099 Open : HTTP
Port 3306 Open : MySQL server
Tried to connect to the SCQ-Server with MySQL-Front:
1130 - Host 'x' is not allowed to connect to this MySQL server
\\192.168.178.110 (my TG01) : empty folder over netbios
Tried to connect to the HTTP-Deamon with Firefox:
192.168.178.110:1028
192.168.178.110:1070
192.168.178.110:1099: 404 Not Found
ERR_ACCESS_DENIED
AR7 Webserver Fri, 22 Apr 2011 15:47:59 GMT
...like the normal "Windows Mobile-based Device" if I add a fixed ip.
Something has happened to my TG01... sometimes when i boot normally, it keeps freezing and going into the debug mode... is this due to the new kitchen?
olyloh6696 said:
Something has happened to my TG01... sometimes when i boot normally, it keeps freezing and going into the debug mode... is this due to the new kitchen?
Click to expand...
Click to collapse
If its the white screen debug mode that displays your imei etc, then follow instructions to induce debug mode in post 2, choose 3 with the volume up down and camera buttons and then when you soft reset your phone again it should not appear.
Related
Ok, I have been seeing that many of the members are facing problem in installing USB VCOM driver in preferably in Windows 8. Before you go for installing USB VCOM driver you first have to disable automatic driver installation otherwise your OS might install wrong driver from the net and then you would keep waiting after hitting download button of SP Flash Tool.
How to enable/disable automatic driver installation for Windows 8
Description: How to enable or disable the automatic driver installation feature in Windows 8 for newly added hardware.
1. Right-click on Computer and then click on Properties.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. Click on Advanced system settings.
3. When System Properties opens, click on the Hardware tab.
4. Once in the Hardware tab, click on Device Installation Settings.
5. Once the Device Installation Settings window has appeared, click on the radio button next to No, let me choose what to do.
6. Once No… has been selected, there will be three new options that appear below the previously selected choice. Click on Never install driver software from Windows Update. The check-marked box next to Automatically get the device app and info provided by your device manufacturer can be left checked.
7. Once all the changes have been made, click on Save Changes to save all the settings changed on that screen and then the screen will close.
8. Once back to the System Properties window, Click OK to save changes and close out of System Properties.
Once you have followed this tutorial, you have to follow another tutorial so that your OS can install Unsigned drivers, follow this tutorial.
http://forum.xda-developers.com/showthread.php?t=2303046
Now you are ready to install USB VCOM driver.
Download driver from links given below:
For Window XP, Vista and Windows 7 (Thanks to bhargav1991): http://forum.xda-developers.com/attachment.php?attachmentid=1786965&d=1362676523
For Windows 8 (Thanks to Kumar Abhishek): http://www.mediafire.com/?7yee2of64nhl947
1. Take the battery, SD card and SIM out of the phone
2. Open device manager (on computer search it or control panel)
3. Holding volume+ connect it to PC via USB (once you hear a sound from PC you can release Volume +)
4. In other devices MT65xx Preloader
7. Right click MT65xx Preloader
8. Go to update driver
9. Locate the drivers provided according to your OS (XP, Vista, Windows 7 or Windows 8)
10. And let it do its work.
You might have to reboot your system after installing VCOM driver, to confirm connect your device once again without battery and see if you something like "MediaTek PreLoader USB VCOM Port" means your driver is installed properly if you still see "MT65xx PreLoader" you have to repeat the process.
Remember the hardware in the Device Manager is visible for few secs only.
Any solution for this?
Thanks for this!
It does install the driver correctly but i still cannot flash...
In the hardware manager i cannot see it, only when i select "see hidden devices".
Even when my telephone is connected, it will show in the driver description: the device is currently not connected.
How can i solve this?
coolbud012 said:
Any solution for this?
Click to expand...
Click to collapse
That is adb driver, You don't have to worry about adb driver, you don't require it for flashing.
mainstreamer said:
Thanks for this!
It does install the driver correctly but i still cannot flash...
In the hardware manager i cannot see it, only when i select "see hidden devices".
Even when my telephone is connected, it will show in the driver description: the device is currently not connected.
How can i solve this?
Click to expand...
Click to collapse
Pre-loader is visible only for 2-3 secs, don't worry about this hit download button and then connect your device to PC, it should start flashing.
nice_guy75 said:
Pre-loader is visible only for 2-3 secs, don't worry about this hit download button and then connect your device to PC, it should start flashing.
Click to expand...
Click to collapse
It tried that but it won't flash.
Reinstalled the drivers several times, but nothing.
I get an error about pmt or something.
i followed ur step by step tutorial but not working
device is connecting and within a few seconds it is disconnecting ............... :crying:
I installed the drivers over and over again.
Only the MediaTek PreLoader USB VCOM Port get's installed.
After that i try to flash, but always the same error:
PMT Changed for rom; it must be downloaded.
What can i do?
CHAITANYA KANTETI said:
i followed ur step by step tutorial but not working
device is connecting and within a few seconds it is disconnecting ............... :crying:
Click to expand...
Click to collapse
It doesn't matter, you just go ahead and flash your ROM, you would be able to flash your ROM easily.
mainstreamer said:
I installed the drivers over and over again.
Only the MediaTek PreLoader USB VCOM Port get's installed.
After that i try to flash, but always the same error:
PMT Changed for rom; it must be downloaded.
What can i do?
Click to expand...
Click to collapse
It is not the problem of driver, your Scatter file is of some different device, either download stock ROM from Moulinsky or make one using MTK droidtool.
It worked for me guys in windows 8 :good: but not in windows 7
nice_guy75 said:
It is not the problem of driver, your Scatter file is of some different device, either download stock ROM from Moulinsky or make one using MTK droidtool.
Click to expand...
Click to collapse
hi Nice guy,
I am facing same issue with Lenovo S820, downloaded Stock rom but i think scatter file is missing something as Preload entry is missing. can you give any pointer for this solution
Edit : I am getting PMT Error too .. Tried Latest SP Flash tool too
thanks in advance
Vaibhav
nice_guy75 said:
Pre-loader is visible only for 2-3 secs, don't worry about this hit download button and then connect your device to PC, it should start flashing.
Click to expand...
Click to collapse
QU
My system is win 7 ulmate 32 bit.
How to enable installation of unsigned drivers?
The tut is for win 8, and for 64 bits.
I followed a command prompt method of " bcdedit....checks" (for win 7 /64 bit) but it did not work.
I downloaded the vcom drivers for win 7 uploaded by bharghav 1991 but on installation the system said it could not install the file because it was an INF file.
On one occasion I got the preloaded installed, which said I was good to proceed ,but nothing happened.
I have tried all the sp tools and drivers available on the internet as administrator.
My device SD and desk top have turned to virtual grave yards of software souls.
AndI am getting nowhere.
I also tried the battery in method mentioned above .
Thanks in advance
nice_guy75 said:
Ok, I have been seeing that many of the members are facing problem in installing USB VCOM driver in preferably in Windows 8. Before you go for installing USB VCOM driver you first have to disable automatic driver installation otherwise your OS might install wrong driver from the net and then you would keep waiting after hitting download button of SP Flash Tool.
How to enable/disable automatic driver installation for Windows 8
Description: How to enable or disable the automatic driver installation feature in Windows 8 for newly added hardware.
1. Right-click on Computer and then click on Properties.
2. Click on Advanced system settings.
3. When System Properties opens, click on the Hardware tab.
4. Once in the Hardware tab, click on Device Installation Settings.
5. Once the Device Installation Settings window has appeared, click on the radio button next to No, let me choose what to do.
6. Once No… has been selected, there will be three new options that appear below the previously selected choice. Click on Never install driver software from Windows Update. The check-marked box next to Automatically get the device app and info provided by your device manufacturer can be left checked.
7. Once all the changes have been made, click on Save Changes to save all the settings changed on that screen and then the screen will close.
8. Once back to the System Properties window, Click OK to save changes and close out of System Properties.
Once you have followed this tutorial, you have to follow another tutorial so that your OS can install Unsigned drivers, follow this tutorial.
http://forum.xda-developers.com/showthread.php?t=2303046
Now you are ready to install USB VCOM driver.
Download driver from links given below:
For Window XP, Vista and Windows 7 (Thanks to bhargav1991): http://forum.xda-developers.com/attachment.php?attachmentid=1786965&d=1362676523
For Windows 8 (Thanks to Kumar Abhishek): http://www.mediafire.com/?7yee2of64nhl947
1. Take the battery, SD card and SIM out of the phone
2. Open device manager (on computer search it or control panel)
3. Holding volume+ connect it to PC via USB (once you hear a sound from PC you can release Volume +)
4. In other devices MT65xx Preloader
7. Right click MT65xx Preloader
8. Go to update driver
9. Locate the drivers provided according to your OS (XP, Vista, Windows 7 or Windows 8)
10. And let it do its work.
You might have to reboot your system after installing VCOM driver, to confirm connect your device once again without battery and see if you something like "MediaTek PreLoader USB VCOM Port" means your driver is installed properly if you still see "MT65xx PreLoader" you have to repeat the process.
Remember the hardware in the Device Manager is visible for few secs only.
Click to expand...
Click to collapse
***********
for the sole purpose of rooting my lenovo a 7000, i have installed win 8.
the drivers with the device just dont install,no matter i give auto run etc.
then I pull the battery out and pressing vol up connect my device. the click sound does not come.
and there are just too many drivers. which one should i update?
I'm on the same boat as everyone, the Windows 7 drivers do not work.
Device: LG-D325
I tried rooting, unlocking bootloader, and installing custom rom (this link).
I successfully gained root & unlocked bootloader. Than it all went down.
I flashed recovery and booted into it, using "fastboot boot recovery.img" command.
I flashed cm12.1 and after that I got the "purple screen" error.
When phone is off and I try to normally turn it on:
1st screen:
Code:
Secure booting error!
Cause: boot certification verify
2nd screen:
Code:
DemiGod Crash Handler : DBI Err Fatal!
Board Rev.: 1.0
Ram dump mode.
Option : SD card ram dump mode.
Push below files to sd card before test.
rdcookie.txt, rtcookie.txt
Please do following action.
1) Ram dump Mode. Please connect USB.
2) Get the ram dump image using QPST Configuration.
3) If sdcard ram dump enabled just wait for reboot.
4) Collect ramdump files from your pc or sdcard.
5) Send e-mail to [email protected]
The same happens when I plug in the USB cable when phone shut off.
Also, I cannot enter the fastboot menu (previously I could - before flashing CM12.1 via recovery) using volume UP + power buttons. Therefore, I cannot enter recovery.
Any info on this situation?
You need to short the test point of your phone and force the phone to qhsusb dload mode after that boot repair
it will repair your phone's download mode
And flash the phone
Br
Shahzaib Jahangir
Is there any way to fix this problem bro with out jtak
Thanks.
The test point method is not the JTAG method
razeen said:
Is there any way to fix this problem bro with out jtak
Thanks.
Click to expand...
Click to collapse
Use the test point method. It works very well and it's quite easy. But first I recommend you try "LG Flash Tool 2014" . If that works, no need to open up the phone for test point method. If you are already seeing pink screen demigod error DBI fatal error, no need to go for JTAG I think.
Feel free to ask if you need assistance for testpoint method. I have already published the method for few other people here on XDA. A little search will bring you there
my Lg325 also violet and dump mode cant flash i go to celpon repair but they cant fix my pon pls help me tnx
gilliane.08 said:
my Lg325 also violet and dump mode cant flash i go to celpon repair but they cant fix my pon pls help me tnx
Click to expand...
Click to collapse
May be I can help you. But first you need a PC, a good internet connection and patience.. If you're interested, reply me.. I will guide you how to unbrick or come out from that pink screen/demi-god screen
honeybun.1986 said:
May be I can help you. But first you need a PC, a good internet connection and patience.. If you're interested, reply me.. I will guide you how to unbrick or come out from that pink screen/demi-god screen
Click to expand...
Click to collapse
same problem here
can you help, please?
LG D325f L70
UPDATE
Now i have QDLoader 9008 (i've installed driver manually without signature). I don't know why my computer did not recognise automatically installed drivers
Else i trieb Board diag
I,ve tried QFIL QPST and recieved
/*invalid image type recieved*/
is_ack_succesfull : 1031 SAHARA_NAK_INVALID_IMAGE_TYPE
sahara protocol error
uploading image using sahara protocol failed
Before that
BoardDiag 3.99c I have an error
AP CHECK START
FAILED during loading flash programmer
There were already messages about this trouble,but there are no solution, so i am asking for it.
LGE AndroidNet USB
qhsusb_bulk
Previously i had Pink screen and Lg Pc Suite could recognize my phone
I,ve tried Format to Fat32 my inner phone emmc(i did not insert in my phone microSD card) DiskImageRev2.zip and LoaderD325.img. After format to fat32 it was 4gb.When i,ve installed loader.img it became 64mb with 2 folders in it. Device monitor showed the phone as qhsusb_bulk (i already had istalled Qualcomm drivers) After installation of LGMobileDriver_WHQL_Ver_4.0.4.exe ( 12,39 МБ )
It was recognised as LGE AndroidNet USB. (com port 3) After that i tried LgFlash tool (tot and kdz firmware,it showed error on 50%) 2014 and BoardDiag also showed error .
I can not convert it to Qualcomm HS-USB QDLoader 9008 (I saw many articles where people with qhsusb_bulk converted it to Qualcomm 9006 after installation of qualcomm drivers,but it did not works for me. Please help
Any ideas? I heared about SRK tool 2.1 Does it works for my Lg L70 D325? Or maybe QPST, or ADP
honeybun.1986 said:
May be I can help you. But first you need a PC, a good internet connection and patience.. If you're interested, reply me.. I will guide you how to unbrick or come out from that pink screen/demi-god screen
Click to expand...
Click to collapse
Please help me
My lG D325 cant on recovery and download mode. Fatal error. Who can help me
Gayan360 said:
My lG D325 cant on recovery and download mode. Fatal error. Who can help me
Click to expand...
Click to collapse
I think you are referring to the famous "purple screen" mode. Relax, that is not hard to get pass.
Follow the steps below.
But, be warned, I am not responsible for any damage caused by following these methods.
Your phone's battery has to be charged at least 50%.
You'll need a USB "data" cable.The one came with your phone is the best. Some third party cables have only power lines connected in and they will not work. So, make sure you have the "data" cable.
1. First, we have to install the necessary drivers(I am assuming that you're using a Windows PC) .
Here are the drivers. Download, install and give your PC a restart.
2. Download LG flash tool 2014 from here and extract it to your root directory(For example, drive "C " in your PC )
3. Download the firmware file for your specific phone model. In your case, as you have mentioned, it is LG D325. This is a link to a matching firmware for LG L70 D325. This file is big and its around 920MB. After download, extract the zip file to the folder where you copied the LG Flash tool 2014.
4. I hope the above mentioned steps were followed correctly and you're ready now. Remove your battery, press the power button for 5-10 seconds and then re insert the battery. press the volume up button and plug the USB cable(The other end has to be plugged in first to PC. Refer to this video if you are unclear.
5. Now launch "LG Flash tool 2014.3.exe" (right click on it and select "run as administrator" for best results).
6. Once the program is open, and click on 1 and select your kdz file which you got from the step 3. Then click either "Normal Flash(2)" of "CSE Flash".
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
7. Now another window will appear and click "Start" as in this picture.
wait until the program finishes and once done, you'll get the initial setup screen on your phone with a greeting message.
If you're still unclear, please pass a comment. Happy communicating..
For a week now,i have been trying to troubleshoot these issues and they ended up in vain.
The problem occurred,when i first tried to flash CM recovery ,i Typed in "FASTBOOT oem unclock",then everything went into this havoc.
The the phone ,boots into Fastboot mode Only when i press the (Vol Urip+power).
No recovery is Present ,when i try the (Vol Down + Pwer) I get the One plus symbol ,nothing else.
No Rom is present ,so i cant just load into a Rom ,to try something via that way
The images show a few ways that i have tried to solve this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Since i am NOT able to go into recovery ,i am stuck.
Please try helping me solve this ,Thanks !
[The methods that i have previously tried before asking this is ,
Tried to use the WinDroid Toolkit ,almost a couple other threads regarding bootloop(since i am unable to get the Recovery screen itself) all that didn't help]
Edit: If above links of image don't load
http://postimg.org/image/awmyeceiz/
http://postimg.org/image/iulytqh6z/
arundp95 said:
For a week now,i have been trying to troubleshoot these issues and they ended up in vain.
The problem occurred,when i first tried to flash CM recovery ,i Typed in "FASTBOOT oem unclock",then everything went into this havoc.
Click to expand...
Click to collapse
Ok, try this
still stuck.
Thanks for the tip.
I tried that method and this is wher i am stuck at.
When i connect the phone instead of getting Qualcomxxxxx i get RELINK HS-USB QDLOADER 9008(com3)
and because of this the msm downloader,doesnt detect the phone and its stuck there.
Please help.
Thank You
arun
[Solved]
It finally got detected then stated up .
[if anyone gets stuck with this problem,i am more than willing to help you solve it .Ping me ]
Thank you
arun
arundp95 said:
It finally got detected then stated up .
[if anyone gets stuck with this problem,i am more than willing to help you solve it .Ping me ]
Thank you
arun
Click to expand...
Click to collapse
Do mention here. It will be helpful for everyone.
[Solved] OnePlus X Brick
saurabh40629 said:
Do mention here. It will be helpful for everyone.
Click to expand...
Click to collapse
Sure.
As the Post above mentioned (in the first comment) ,thats the way to go to fix a Hard bricked / bootloop stuck / no Display.
But if you encounter any problems or issues like i did (the QualCom 9008 ...).I did these
Note : all downloads for this adventure are already present in that guide ,Give it a thumbs up after you fix it as it just recovered a potato , link
HTML:
http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
Step 1: Requirements
Download the qualcom drivers,fastboot-adb all of that,even though i had them installed,i did a clean installation.
Download the Huge 800MB file (the Recovery tool).
Unzip them to the Desktop, 2 folders (1 for the Qualcomm driver,another for the msm).
Step 2: Set-up
Follow the turning off drive signature process from the post above ,Its fairly simple(press shift restart,advanced,f7 restart).
Install adb-drivers.
Switch off phone (press Power Button for 12 sec or so )till it vibrates and display is blank.
Press the Power Up button and plug in the Phone to your comp
If your Internet connection is turned on,mostly windows will itself download and install the driver(qualcom-xxx) for this device.
Step 3:
Now Unplug the phone.Switch it off(your display will be blank ,to begin with but remove phone press power button 12 sec (wait for vibrate )
Press power button up and plug it back in the comp.When you do this navigate to the Device manager tab ,A new entry in that table will be present Ports & Coms or so. If you dont have this ,no worries (go back to the First step and try to get your drivers re-Installed) .
Now that you have located your com port, RELINK HS-USB QDLOADER 9008(com3) in my case( you might have anything else ,but getting this is crucial).
On that Entry right click and go to Properties.In properties > Driver Tab > Update Driver
Once you click Update, Click on Browse my comp for driver
Then Click on LET ME PICK FROM A LIST
UNCHECK the SHOW COMPATIBLE HARDWARE // Have to do this !
Under Manufacturer,FIND Qualcomm Incorporated
Under MODEL,Select QUALCOMM HS- USB MSM DIAGNOSTICS xxxx (i chose the first entry,BUT MSM is integral).
Install that .RESTART COMP,IT'll PROMPT.
UNPLUG PHONE ,SWITCH OFF ,Press POWER UP+ for 12sec
Reconnect to the comp ,now your DEVICE MANAGER will show your port ENTRY as QUALCOMM HS-USB MSM DIAGNOSTICS
Click on that entry and Click on Properties > Driver >Update >Browse my comp >
Now select the folder in which you have downloaded the Qualcomm drivers x64 or x86 (from the post above ,you should have downloaded them in the beginning).
Now install that , If it asks for an Restart COMP ,RESTART comp( i restarted,just to be safe).
Step 4 : Completion
Connect the phone in fastboot mode(Just the power up+ & connect )
msm.exe > open in admin mode.
Open up the MSM.exe in the folder (the big file that you downloaded earlier the 800MB one )
It will recognize your device,If it doesn't.
Unplug Phone.
Power Off
Power Up+ ,wait 10sec ,and Plug in ,(hold the power up)
MSM.exe will recognise your device, Try to click start on that and see if it triggers it ,else just close and reopen msm.exe
Your device will be recognised Press Start, it'll do the rest.
After all this,a recovery mode will show up,click yes/ no and Continue.
That's all.OnePlus X good as new
arun.
arundp95 said:
Sure.
That's all.OnePlus X good as new
arun.
Click to expand...
Click to collapse
Let's hope someone finds this useful in future. Thanks for the detailed steps to recover the phone.
arundp95 said:
Sure.
As the Post above mentioned (in the first comment) ,thats the way to go to fix a Hard bricked / bootloop stuck / no Display.
But if you encounter any problems or issues like i did (the QualCom 9008 ...).I did these
Note : all downloads for this adventure are already present in that guide ,Give it a thumbs up after you fix it as it just recovered a potato , link
HTML:
http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
Step 1: Requirements
Download the qualcom drivers,fastboot-adb all of that,even though i had them installed,i did a clean installation.
Download the Huge 800MB file (the Recovery tool).
Unzip them to the Desktop, 2 folders (1 for the Qualcomm driver,another for the msm).
Step 2: Set-up
Follow the turning off drive signature process from the post above ,Its fairly simple(press shift restart,advanced,f7 restart).
Install adb-drivers.
Switch off phone (press Power Button for 12 sec or so )till it vibrates and display is blank.
Press the Power Up button and plug in the Phone to your comp
If your Internet connection is turned on,mostly windows will itself download and install the driver(qualcom-xxx) for this device.
Step 3:
Now Unplug the phone.Switch it off(your display will be blank ,to begin with but remove phone press power button 12 sec (wait for vibrate )
Press power button up and plug it back in the comp.When you do this navigate to the Device manager tab ,A new entry in that table will be present Ports & Coms or so. If you dont have this ,no worries (go back to the First step and try to get your drivers re-Installed) .
Now that you have located your com port, RELINK HS-USB QDLOADER 9008(com3) in my case( you might have anything else ,but getting this is crucial).
On that Entry right click and go to Properties.In properties > Driver Tab > Update Driver
Once you click Update, Click on Browse my comp for driver
Then Click on LET ME PICK FROM A LIST
UNCHECK the SHOW COMPATIBLE HARDWARE // Have to do this !
Under Manufacturer,FIND Qualcomm Incorporated
Under MODEL,Select QUALCOMM HS- USB MSM DIAGNOSTICS xxxx (i chose the first entry,BUT MSM is integral).
Install that .RESTART COMP,IT'll PROMPT.
UNPLUG PHONE ,SWITCH OFF ,Press POWER UP+ for 12sec
Reconnect to the comp ,now your DEVICE MANAGER will show your port ENTRY as QUALCOMM HS-USB MSM DIAGNOSTICS
Click on that entry and Click on Properties > Driver >Update >Browse my comp >
Now select the folder in which you have downloaded the Qualcomm drivers x64 or x86 (from the post above ,you should have downloaded them in the beginning).
Now install that , If it asks for an Restart COMP ,RESTART comp( i restarted,just to be safe).
Step 4 : Completion
Connect the phone in fastboot mode(Just the power up+ & connect )
msm.exe > open in admin mode.
Open up the MSM.exe in the folder (the big file that you downloaded earlier the 800MB one )
It will recognize your device,If it doesn't.
Unplug Phone.
Power Off
Power Up+ ,wait 10sec ,and Plug in ,(hold the power up)
MSM.exe will recognise your device, Try to click start on that and see if it triggers it ,else just close and reopen msm.exe
Your device will be recognised Press Start, it'll do the rest.
After all this,a recovery mode will show up,click yes/ no and Continue.
That's all.OnePlus X good as new
arun.
Click to expand...
Click to collapse
Hi Saurabh40629/ arundp95
that 800mb link may be expired. unable to download the file.could you please share the new link. it'll be really helpful for me.
I am trying to resolve this from last week unable to get that file.
Please Help!!!!!!!
Hi vinesh ,
Did you got the 800mb recovery tool link
Hi hear i am going to share how to root Vibe s1 Marshmallow With custom Recovery TWRP
Requirements 1) SP Flash Tools 5.1524.00 – https://spflashtool.com/download/SP_Flash_Tool_v5.1524.00.000.zip
2) LenovoVibe S1 Drivers & Mediatek USB VCOM Drivers – Drivers
3) Lenovo_Vibe_S1_TWRP-3.0.2.3-M_by_SevenMaxs.zip +
SuperSu TWRP-3.0.2.3-M_by_SevenMaxs.zip +
SuperSu
InstructionsKeep your device battery charged above 50%
Enable USB Debugging on your device.
Go to > Settings > Developer Options > USB Debugging.
If Developer Options is not located under settings then enable it by going to Settings > About Phone > Device Info and tap on Build Number for about 7-8 times. And then go back and follow the previous step.
Step 1: Install the Lenovo Vibe S1 Driver & Mediatek Driver ( first go to smartphone driver and install "dpinst.exe" then install Usb VCOM driver. to do that please refer google to how to do it in your current OS
Step 2: Extract SP Flash Tools on your desktop
Step 3: Extract TWRP folder on your desktop
Step 4: Open flash_tool.exe from the SP Flash Tools folder and clock Scatter-loading and then browse the TWRP folder and select the MT6752_Android_scatter.txt
Step 5: In the Flash Tool Window Press CTRL + SHIFT + O a new options window will open. Click download and then tick USB Checksum and close the window
Step 6: Now click the download button
Step 7: Switch off your Lenovo Vibe S1 and then connect it using the USB to the computer/laptop
Step 8: You will get the Download Complete window within a moment
9) Remove the cable and press volume up and down + powerkey together and wait for the the lenovo logo or vibrate, it will go to twrp if you see black scree please wait for 2 mintues after twrp come copy the "UPDATE-SuperSU-v2.46" file to the phone and flash it
Note: Custom Recovery of SevenMaxs is the current updated recovery available but when you try to Wipe (dalvik,cache,system,data,etc) it will take more time ,you have to wait it to complete other than this no other issue
All the above are taken from different resources so if you find any difficulty ask to known experts.
Thanks to @techolite.com , @supersayan1000
Can't actually boot up after following steps provided
Hi, thanks for your hard work for making a post related to root for Lenovo Vibe S1 root. Currently I was following the steps,until the last step, my phone was in the dark screen and nothing came out after waiting 2 minutes. May I know if there is any solution to solve this problem?
I know how to solve this
bricked my phone
had to flash with stock rom after following instructions. beware.
The same problem
smpmfx2s96 said:
Hi, thanks for your hard work for making a post related to root for Lenovo Vibe S1 root. Currently I was following the steps,until the last step, my phone was in the dark screen and nothing came out after waiting 2 minutes. May I know if there is any solution to solve this problem?
Click to expand...
Click to collapse
Do remember this twrp recovery will only work on Android 6.0 :cyclops:
Twrp takes takes about 1-2 minutes to boot up as it has to time out the screen once to turn on the display(bug in twrp) in that time don't press anything or tap on the screen or the timeout will reset, after waiting for 1 minute(screen time out time) press power key and it should show the twrp recovery :highfive:
and yeah after flashing twrp, please flash SuperSu or Magisk or you'll face bootloop :silly:
I complete all step, but my Android Phone is vibrate every 1 mint,So How to Solve this Problem?
Aravindappu000 said:
I complete all step, but my Android Phone is vibrate every 1 mint,So How to Solve this Problem?
Click to expand...
Click to collapse
i have the same problem
Brick FIXED by Checking both USB Checksum and Storage Checksum Thanks for advice
wrking
ivoriez said:
Brick FIXED by Checking both USB Checksum and Storage Checksum Thanks for advice
Click to expand...
Click to collapse
thanks ... it worked fr me as well :good::good:
---------- Post added at 10:01 AM ---------- Previous post was at 09:33 AM ----------
supersayan1000 said:
Do remember this twrp recovery will only work on Android 6.0 :cyclops:
Twrp takes takes about 1-2 minutes to boot up as it has to time out the screen once to turn on the display(bug in twrp) in that time don't press anything or tap on the screen or the timeout will reset, after waiting for 1 minute(screen time out time) press power key and it should show the twrp recovery :highfive:
and yeah after flashing twrp, please flash SuperSu or Magisk or you'll face bootloop :silly:
Click to expand...
Click to collapse
I have rooted my s1a40 by the above method and flashed superuser also. now I am looking for a custom rom for my device which may upgrade it to latest android version along with VoLTE support. Can
I get any help.
Pressing of power + volume up +volume down is making a small vibration but nothing in the display.. please provide a solution.
hi broo the file is broken plz reupload it
TWRP-3.0.2.3-M_by_SevenMaxs.zip +
SuperSu
Is this for Lenovo S1a40 ?
hi,
i've done all the steps, but when i want to recovery to flash supersu, it goes to screen with chinese menu ???
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
anyone help ?
dejan- said:
hi,
i've done all the steps, but when i want to recovery to flash supersu, it goes to screen with chinese menu ???
anyone help ?
Click to expand...
Click to collapse
Did flash was successfull. Read all comments. Try again, if you see Chinese recovery then it should indicate that your flashing was unsuccessful
alwynjoshy said:
Did flash was successfull. Read all comments. Try again, if you see Chinese recovery then it should indicate that your flashing was unsuccessful
Click to expand...
Click to collapse
hi,
it says succesfull.. I get the Download Complete window within a moment.
i have windows 10, and phone is detected it self.
Step 1: Install the Lenovo Vibe S1 Driver & Mediatek Driver ( first go to smartphone driver and install "dpinst.exe" then install Usb VCOM driver. to do that please refer google to how to do it in your current OS
Click to expand...
Click to collapse
when i run "dpinst.exe" i'm getting:
i did install USB VCOM driver tho.
Then 9) Remove the cable and press volume up and down + powerkey together and wait for the the lenovo logo or vibrate, it will go to twrp if you see black scree please wait for 2 mintues after twrp come
Click to expand...
Click to collapse
when i press volume up and down + powerkey together and wait for the the lenovo logo or vibrate, phone boots normaly, no twrp ?
i tried also volume up + powerkey (the same) ... i can't get to twrp, that i would install supersu
dejan- said:
hi,
it says succesfull.. I get the Download Complete window within a moment.
i have windows 10, and phone is detected it self.
when i run "dpinst.exe" i'm getting:
i did install USB VCOM driver tho.
when i press volume up and down + powerkey together and wait for the the lenovo logo or vibrate, phone boots normaly, no twrp ?
i tried also volume up + powerkey (the same) ... i can't get to twrp, that i would install supersu
Click to expand...
Click to collapse
For me vCom driver zip shows Corrupted, do you have any issues?
alwynjoshy said:
For me vCom driver zip shows Corrupted, do you have any issues?
Click to expand...
Click to collapse
well i installed vcom driver with this steps:
1) Boot to Advanced Startup Options
a) Open the "Start" Menu
Open Settings and click on the "Update & security" icon
Click on "Recovery" on the left side and
click on "Restart now" under Advanced startup on the right side
2) Select "Troubleshoot"
3) Select "Advanced Options"
4) Select "Startup Options"
5) Select "Restart"
6) A menu will appear where you can press “F7” on your keyboard to choose “Disable driver signing enforcement“
To install Windows 10 MTK VCOM USB Drivers :
2) Open folder, right click on InstallDriver and run as administrator
3) Install drivers
4) Right-click on Start Menu
5) Select Device Manager
6) Mark your computer and click Action
7) Select Add Legacy Hardware
8) Select Manually Install
9) Click on Show All Device,then Have disk…
10) Find MTK USB Driver for your OS (64 or 86) and click OK
11) Select MTK USB Port and click Next to install
Click to expand...
Click to collapse
somehow i managed to come into TWRP (altho language is russian), but i also managed to flash SuperSU ....so finaly it works
tnx
dejan- said:
somehow i managed to come into TWRP (altho language is russian), but i also managed to flash SuperSU ....so finaly it works
tnx
Click to expand...
Click to collapse
great , what happened really
Hello to all ZenFone4 (ZE554KL) owners.
(I am not good at English so I use DeepL translation.)
I would like to backup the data of an app, please lend me your wisdom.
Here is the app that has the problem.
小説を読もう！オフラインリーダー - Apps on Google Play
More convenient, comfortable! "Restaurant novel!" And "Shousetsukaninarou"
play.google.com
This app is an offline reader for a famous Japanese novel submission site.
I have been using this app since 2014 until now.
But recently I had a problem with data backup.
This app is originally equipped with a backup function.
However, if the file size of the database (SQLite3) used internally exceeds 2GB, the backed up data is interrupted there.
Also, until now, it was possible to backup using the Android adb backup function and retrieve the data from backup.ab to get the same data even if the file size exceeded 2GB.
But now this method also stops in the middle of the backup and fails.
This app has not provided any updates since 2018.
Also, I have not been able to contact the developer by sending an email to their email address.
I thought about rooting the device and backing it up, but I have not been able to do so because I have heard (with Android in general) that unlocking the bootloader will initialize all user data.
Is there any good way to do this?
Thank you for reading this far.
Japanese(Original)
ZenFone4(ZE554KL)をお持ちの皆さんこんにちは。
(英語が不得意なのでDeepL翻訳を使用しています。)
あるアプリのデータのバックアップを行いたいのですが知恵を貸してください。
問題があるアプリはこれです。
小説を読もう！オフラインリーダー - Apps on Google Play
More convenient, comfortable! "Restaurant novel!" And "Shousetsukaninarou"
play.google.com
このアプリは日本の有名な小説投稿サイトのオフラインリーダーです。
私は2014年から今までずっとこのアプリを使用し続けてきました。
ですが最近になってデータのバックアップに問題が発生しました。
このアプリは本来バックアップ機能が搭載されています。
しかし、内部で使用されているデータベース(SQLite3)のファイルサイズが2GBを超えるとバックアップしたデータがそこで途切れてしまう問題が発生します。
また、今までは2GBを超えてもAndroidのadb backup機能を使用してバックアップを行いbackup.abからデータを取り出すことで同じデータを得ることもできました。
ですが、現在ではこの方法もバックアップの途中で止まってしまい失敗します。
このアプリは2018年からアップデートが提供されていません。
また、デベロッパーのメールアドレスにメールを送っても連絡が付きません。
端末をrootしてバックアップすることも考えましたが、(Android全般で)ブートローダーをアンロックするとユーザーデータが全て初期化されてしまうという話を聞いたので行えていません。
何か良い方法はないでしょうか？
ここまでお読みいただきありがとうございます。
provide info more about phone. Snapdragon 630 or Snapdragon 660?
https://play.google.com/store/apps/details?id=ru.andr7e.deviceinfohw
aIecxs said:
provide info more about phone. Snapdragon 630 or Snapdragon 660?
https://play.google.com/store/apps/details?id=ru.andr7e.deviceinfohw
Click to expand...
Click to collapse
Model ASUS_Z01KDA(WW_Z01KD)
SOC Snapdragon 660
RAM 6GB
ROM 64GB
Android Ver 8.0.0
Build ID
OPR6.170623.013.WW_Phone-15.0405.1806.116-0
please read boot.img off device and share file (we will check if we can cheat bootloader)
on PC
install python, install this https://github.com/bkerler/edl
Code:
adb reboot edl
python3 edl --loader=/path/to/prog_emmc_ufs_firehose_Sdm660_ddr.elf r boot boot.img
if you can't enter EDL mode from adb, try this:
- disconnect usb cable
- power off phone entirely
- press and keep holding both volume buttons
- connect usb cable
I live in Japan where it is just before 6 am and I am so sleepy I am going to miss the work, so I will try again later.
Thank you very much.
Japanese(Original)
私が住んでいる日本は、今午前6時直前で私が眠くて作業をミスしそうなので、また後で試させていただきます。
ありがとうございます。
aIecxs said:
please read boot.img off device and share file (we will check if we can cheat bootloader)
on PC
install python, install this https://github.com/bkerler/edl
Code:
adb reboot edl
python3 edl --loader=/path/to/prog_emmc_ufs_firehose_Sdm660_ddr.elf r boot boot.img
if you can't enter EDL mode from adb, try this:
- disconnect usb cable
- power off phone entirely
- press and keep holding both volume buttons
- connect usb cable
Click to expand...
Click to collapse
I tried it, but I can't seem to get into edl mode with the adb reboot edl command or with the USB cable connected while holding down the volume button.
I was able to enter CSC fastboot mode by booting while holding down the Volume plus button. ......
In addition, a mysterious barcode appears on the right side of the screen when I enter fastboot mode using the adb reboot bootloader command.
Japanese(Original)
試してみましたが、adb reboot edlコマンドでもVolumeボタン押しながらUSBケーブル接続でもedlモードに入れないようです。
Volumeプラスボタンを押しながら起動するとCSC fastboot modeには入りましたが……
なお、adb reboot bootloaderコマンドを使用してfastbootモードに入ると画面右側に謎のバーコードが表示されます。
1) maybe translation was wrong.
press two Volume Buttons at same time. Volume Up & Volume Down. then connect usb cable.
2) another method from modified fastboot
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo]
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo] Reboot to EDL mode from FASTBOOT! No more Test Point Method needed ;) Technical Details: Redmi Note 3 support rebooting to EDL in Android Bootloader aboot...
forum.xda-developers.com
3) another method with deep flash cable
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4) another method via test point
aIecxs said:
1) maybe translation was wrong.
press two Volume Buttons at same time. Volume Up & Volume Down. then connect usb cable.
2) another method from modified fastboot
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo]
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo] Reboot to EDL mode from FASTBOOT! No more Test Point Method needed ;) Technical Details: Redmi Note 3 support rebooting to EDL in Android Bootloader aboot...
forum.xda-developers.com
3) another method with deep flash cable
4) another method via test point
Click to expand...
Click to collapse
It's ok, I was pressing Volume + and - at the same time.
Unfortunately, it didn't go into EDL mode, though.
I'm sure it's a security delight, but it's a shame that it seems to be really difficult to freely play with one's own devices in recent years.
I really respect aIecxs for his erudition.
Even the modified fastboot command reboot-edl didn't work.
I don't have a deep flash cable, but I have an adapter that can pull each signal line from USB Type-C, so I will try that tomorrow.
I've changed the battery several times, so I have disassembled it, but I don't really want to use the test-point if possible because I might accidentally destroy the device.
Japanese(Original)
大丈夫です。Volume +と-を同時に押していました。
残念ながらEDLモードには入りませんでしたけどね。
セキュリティ的には喜ばしい事なのでしょうが、近年は自分のデバイスを自由弄るのが本当に難しいようで残念ですね。
aIecxsさんは博識で本当に尊敬します。
改造したfastbootコマンドのreboot-edlでもダメでした。
deep flashケーブルは有りませんが、USB Type-Cの各信号線を引き出せるアダプタを持っているので明日それを使って試してみます。
何回かバッテリー交換はしているので分解はしていますが、デバイスを誤って壊してしまいそうなのでtest-pointはできればあまり使いたくないですね。
Unfortunately, the test point picture is for Snapdragon 630. But you can upload picture of PCB board Snapdragon 660.
aIecxs said:
Unfortunately, the test point picture is for Snapdragon 630. But you can upload picture of PCB board Snapdragon 660.
Click to expand...
Click to collapse
This is an image from a previous battery replacement.
The PCB is not visible, but looking at the shape of the plate and the placement of the components, I suspect that the test point is in the same position.
Twitter:
https://twitter.com/i/web/status/1202833859068321793
Japanese(Original)
以前バッテリーを交換した時の画像です。
PCBは見えませんがプレートの形状や部品配置を見るとtest point同じ位置にあるのではないでしょうか？
Twitter:
https://twitter.com/i/web/status/1202833859068321793
aIecxs said:
1) maybe translation was wrong.
press two Volume Buttons at same time. Volume Up & Volume Down. then connect usb cable.
2) another method from modified fastboot
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo]
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo] Reboot to EDL mode from FASTBOOT! No more Test Point Method needed ;) Technical Details: Redmi Note 3 support rebooting to EDL in Android Bootloader aboot...
forum.xda-developers.com
3) another method with deep flash cable
4) another method via test point
Click to expand...
Click to collapse
I substituted the EDL cable with an adapter like the one in the image, but it did not enter EDL mode.
(I used a digital multimeter to verify that the wiring was correct.)
I will try again at a later date as it requires preparation and courage to disassemble and short-circuit the test points.
Thank you very much.
Japanese(Original)
画像の様なアダプタを使用してEDL ケーブルを代用しましたがEDLモードには入りませんでした。
(デジタルマルチメーターを使用して結線が正しいか確認しました。)
分解してテストポイントを短絡させるには心の準備や勇気が必要なのでまた後日試してみようと思います。
ありがとうございます。
We have succeeded in avoiding BackupManager crashes by specifying the -nocompress option in adb backup,
and avoiding adb backup timeouts (5 minutes) by connecting a USB-LAN adapter via OTG and using a wired LAN
connection for backups.
Japanese(Original)
adb backup にて -nocompress オプションを指定することによりBackupManagerのクラッシュを回避し、
USB-LANアダプタをOTGにて接続し有線LAN接続でバックアップすることによってadb backupの
タイムアウト(5分)を回避することに成功しました。