I have t-mobile hd2.i tried to install older HSPL,after restart my hd2 was black like dead.I connect usb but ACTIVE SYNC windows mobile device center didnt detect that but qualcomm cdma technologies msm driver was asked when i connect usb on windows 7 ultimate.here on xda link http://forum.xda-developers.com/showthread.php?t=712924
i got from there the samsung pada drivers worked.
but still no SYNC appeared. but on device manager only 3 ports shown.1 is qualcomm cdma bluetooth incomming port
2nd qualcomm cdma bluetooth outgoing port
and the last qualcomm cdma usb port
CAn i repair it without jteg?bc lcd shown black now bootloader loaded even volume down button
People still making this mistake and flashing non tmous roms, eh? Amazing.
No one has fixed this type of brick except with jtag or new mainboard. However, most people also never get the drivers to install either so I'm sure loads of people will be interested in your findings.
Personally I think its a red Herring, but good luck.
samsamuel said:
People still making this mistake and flashing non tmous roms, eh? Amazing.
No one has fixed this type of brick except with jtag or new mainboard. However, most people also never get the drivers to install either so I'm sure loads of people will be interested in your findings.
Personally I think its a red Herring, but good luck.
Click to expand...
Click to collapse
i think also about Jtag now.but dont know the price of main board?
yousufshah said:
i think also about Jtag now.but dont know the price of main board?
Click to expand...
Click to collapse
Go to eBay and check them out the sale all kinds of HD2 replacement parts on there. Also Google HTC HD2 JTAG and RICFBOX if you want to go that route.
price of mainboards,,, not seen any for sale, but if you send it to a repair shop they charge around 120-150 dollars or there abouts.
Re:JTAG - what T-Mac meant to say was google riffbox, not ricfbox.riffbox isn't the only one, you can google 'ort jtag' too, though be warned the equipment for JTAG method will cost you as much as a new mainboard anyway, plus its not easy.
Go for JTAG if you
1 - are a technical wizard
OR
2 - you already have access to a JTAG box.
A riff box will cost around $150 new, and dont forget you need a jig to hold the mainboard when you connect it to the box (unless you are a master spot solderer), they run at around $20.
I had a simular issue a HTC inspire I refurbished after a cracked screen.
First question I'd like to ask if your volume down button not work properly?
For me it did'nt so i pulled out the volume board behind the button.
Take out the battery and make sure when the battery is put back in have the usb connected to the pc. if using windows go into computer management check if your device is read on the computer when trying these steps.
battery in power on without holding volume down.
HTC phone should be recognized if not next step.
Holding volume down Power on the device your pc should see something but the HTC will have an error in computer management. Look for the ADB driver which will fix this error but your still crashed so go back if you dont have it and download the new rom on the HTC website.
Check if your phone is actually holding a charge. need 30% battery life to flash the new rom.
Then run the rom it should say if theirs a usb error or your phone is detected.
If this doesnt help try another battery fully charged.
dont forget to check your rspl hspl stuff also DFT on this forums made a post how to do it and which versions you need for custom roms.
ADB universal driver for windows here http://forum.xda-developers.com/showthread.php?t=1379875 if it does'nt work you gonna have to look around.
This is a general aproach to helping you my only experience is with the HTC HD7S and the HTC Inspire. Crashed the inspire with my first rom load attempt bsod did that and loaded the rom from the htc site. HD7S used the http://forum.xda-developers.com/showthread.php?t=1195647 hope they are compatable with your phone.
Related
Since Monday morning, I have not been able to sync my phone (was dcd v3.0.4 when it stopped working). I have done much research and have tried many different things in an unsuccessful attempt to solve the issue.
When I plug it in, it begins charging but nothing else happens. No windows new device sound or system tray notification, no driver prompt, no windows activesync activity, nor any activesync activity on the phone (that little arrow icon on the top bar).
I have gotten this problem extremely intermittently previously but have always been able to resolve it with either a soft reset and/or a computer reboot. When that solution attempt failed, I tried moving the usb cable to a different port. I tried four or so different ports with no different results. I tried a different cable. I tried disabling advanced networking, deleting my partnerships (lost my contacts and have not yet been able to re-sync them :/), uninstalling activesync, and cleaning all the activesync files and drivers. I even launched device manager with hidden/non-present devices shown to remove the windows mobile devices (which were oddly not present, although this was after my first activesync uninstall/clean).
After not being able to get anything to respond, I thought it may be something not working properly on my workstation, so I tried similar processes of troubleshooting on my laptop with the same results.
At this point, I figured I had isolated the problem to the device, hopefully being just a software issue and not a hardware issue. At the time, I was still running rom dcd v3.0.4 with radio 3.35. I decided to flash to the newest versions in a hopeful attempt to restore my device's functionality. After flashing radio 3.39 and cooking and flashing a dcd v3.1.2 rom, I tried again with no different results.
Finally, I decided to connect it in bootloader mode, just to see what would happen (what is normal behavior for this anyway? does it get detected and drivers installed correctly?). It was detected as a usb device by my workstation but could not install drivers for it.
Needless to say, I have become rather frustrated with my device this week. I am not sure what the problem is exactly, nor what I could possibly do to fix it. I am on the verge of flashing a stock rom and *gasp* going to the Sprint store for support. Perhaps I finally dropped or shocked it one too many times this past weekend, and it does indeed have a physical issue...
Does anyone have any suggestions/ideas/thoughts? I would be very greatful for any input.
Thank you!
See this thread and see if anything in there fixes your problem.
http://forum.xda-developers.com/showthread.php?t=393918
I have been following that thread in hopes that something may prove helpful and have tried everything suggested, including attempting to clean the port (what would be best for this? anything more than just blowing into it?), trying the two Y adapters I have (emu -> emu / mini-usb & emu -> mini-usb / 2.5" stereo), running that batch script and working with the device manager (those devices were not present), and disabling advanced network functionality, all with no results.
VerusMaya said:
running that batch script and working with the device manager (those devices were not present),
Click to expand...
Click to collapse
If you've sync'd in the past then when you display hidden devices those devices should be present (at least faded). It'll be very strange if you don't see them. If not then uninstall the Mobile Device 6.1 upgrade, restart the PC and reinstall it. Then open up the device manager and watch what changes when you plug in your WinMo device.
Keystone said:
If you've sync'd in the past then when you display hidden devices those devices should be present (at least faded). It'll be very strange if you don't see them. If not then uninstall the Mobile Device 6.1 upgrade, restart the PC and reinstall it. Then open up the device manager and watch what changes when you plug in your WinMo device.
Click to expand...
Click to collapse
I also thought it quite strange that I did not see those devices at all at when I displayed hidden/non-present devices in the device manager. I definitely have sync'd on this machine many times, I typically leave it plugged in throughout the day here at work. My machine is part of a corporate domain but I do not see how anything pertaining to that would affect my devices. On my laptop (used to sync here), the devices were present in the device manager, but even after uninstalling them the phone would not be detected when I plugged it in.
When you say uninstall the mobile device 6.1 upgrade, are you talking about the vista mobile device manager? I am on XP with activesync 4.5.
Also, nothing happens when I plug the device in, not even the standard device connected notification sound. Nothing changes in the device manager, nothing is found when I rescan hardware, I even uninstalled all the usb root hub devices and rescanned for them, hoping a complete usb subsystem driver reinstall may help detect something.
I even downloaded and ran two usb tools, one free usbdeview (http://www.nirsoft.net/utils/usb_devices_view.html) which displayed and monitored all usb devices (present and non-) and drivers and a trial of a usbtrace (http://www.sysnucleus.com/) which was a usb protocol traffic capture and analysis program. I experimented with (un)plugging the phone multiple times in multiple ports with two different cables while running these programs, attempting to find something useful. Absolutely nothing at all happened in either program, which makes me believe it is something either on the phone software or hardware.
I have a feeling I may require a device swap :/
VerusMaya said:
When you say uninstall the mobile device 6.1 upgrade, are you talking about the vista mobile device manager? I am on XP with activesync 4.5.
Click to expand...
Click to collapse
Yeah, activesync then... I dunno, I'm at a loss.
Yeah me too, looks like I am going to have to flash the latest stock Sprint rom and take it in hopefully they can do something for me.
Went to sprint, it was a bad port after all, they gave me a brand new device.
VerusMaya said:
Went to sprint, it was a bad port after all, they gave me a brand new device.
Click to expand...
Click to collapse
Are you sure they gave you the brand new device? coz same thing happened to me a week ago and i went to sprint. They gave me the refurbished phone back. Physical condition of the phone is very good tho.
SptMogul said:
Are you sure they gave you the brand new device? coz same thing happened to me a week ago and i went to sprint. They gave me the refurbished phone back. Physical condition of the phone is very good tho.
Click to expand...
Click to collapse
Well I suppose I am not sure it was brand new, but it had the screen protector and the plastic stickers still on it (next to keyboard when you slide it out). I also received an additional 512MB SD card that comes with it.
Did you flash back to a sprint rom via sd card?
arcanecho said:
Did you flash back to a sprint rom via sd card?
Click to expand...
Click to collapse
Yes, I extracted the two NBH files from the latest (3.35 I believe) stock Sprint rom installer and first flashed the smaller image (bootloader/radio I think it was), and then the larger image (os) before I took it in.
The rep I dealt with at first was somewhat of a technical idiot and only served to confuse/delay matters but after I returned, I spoke to someone else and gave them permission to hard-reset, as well as mentioned I had done this multiple times as well as tried multiple computers and multiple cables, just to help them narrow down the possible source of the problem (as well as to block possible common excuses). After waiting around for half an hour or so in-store, a technician brought me a new phone and told me the port was physically bad.
All-in-all, I was quite pleased with Sprint's service and my free swap for an issueless and scratchless new device. I was afraid it was not going to be quite so easy, requiring more time and/or an insurance replacement fee. Not to mention the free 512mb sd card.
I had a similar problem, I was un able to connect to active sync but was able to charge. Everytime I would try to connect to active sync I got the "device is not recognized" error. Then someone on here suggested perhaps my USB port was messed up, sure enough I looked in the port and noticed one of the gold pins was flipped up slightly higher then the rest. My friend took a needle and adjusted the pin and it was good as new. Somehow I had lifted one of the pins.
Anyways IMHO it's good to look in there and just check if your having problems connecting, it saved me a trip to a technician and having to wait or go through reprogramming everything.
Hello! My USB on my HD2 seems to be acting up, it has been working perfectly before but now I can not connect it to the computer any more. Charging it works fine though.
When I connected on mainscreen i got a "USB device not recognized" resulting in no connection between the computer and the phone. When I enter bootloader I get the device recognized as "Qualcomm CDMA Technologies MSM". I figured, ok, so perhaps it is ROM-connected and I just need to reflash to a stock and all will be fine and dandy.
(There were a lot more of fiddling around with USB settings before I went to bootloader, including reinstalling USB drivers on computer, trying different computers and trying different cables)
Flash got to 8% and then got an error message, now I get to bootloader automaticly on load, still the same Qualcomm device connected but SSPL-program on computer can't find a connection (and obviously not Window Mobile Device Center either.)
Where does my best hope lie? I dont have a cardreader for my microSD here at home so need to go out and grab that for any chance of reflashing that way. But I would seriously prefer to get the USB connection working.
Suggestions? Would be very appreciated!
I have just had excatly the same problem
Sent it to HTC Repiar centre (see their website). Despite other peoples experience mine was excellent. Repaired within a week and returned with new motherboard (hence new USB) and new case. They also fitted a new case as well as new battery terminals.
The phone had been loaded with a new rom by me. HTC reloaded the latest T-mobile rom (phone originally T-mobile) and returned it locked. They offered to send a new unlock code but I just re-loaded another (later) WWE rom.
All fixed - and free of charge.
Top service I say.
Good luck
Hello friends i jus accidentely bricked my Flyer, by flashing wrong Hboot. And warranty is in other country. What could i do? is there any way to ressurect ir on PC?
Thank you for your thoughts and advices
Sounds bleak. Does the device boot at all, what hboot did you flash? What were you trying to do?
it blinks orange when pressing and holding power button. Iwas trying to get back to Gingerbread from Honeycomb with Revolutionery Recovery
Flyer does not boot and the ac adator makes no sound of charging, neither is battery warming.
What hboot did you flash?
FlashENGHBOOT
sorry cant find link rught now
If you have the file upload it and I'll take a look, but in all honesty I'm not terribly hopeful, a different hboot is likely to reformat some of the critical partitions. It is likely that you have permanently bricked it and HTC support is the only option, have you tried contacting them at all?
Where did you find this hboot and why did you think it was a good idea
i was after night shift from work . theres no htc support in Lithuania. i think its still fixable just needs propably tearing part now. it was a desire somekind of hboot.
If it's from a desire or desire HD it is not fixable, if it came from a Desire S there is a slim chance but only if it will boot to hboot.
it was from here:
http://forum.xda-developers.com/showthread.php?t=1187231&page=4
engHBOOToverARX.img
the next logical question would be can you get into hboot by holding volume down and power for a couple of seconds. keep holding as long as needed but if a minute passes, not a good sign
dam night shift
No i can't. Thats why i made this post i think everything is going to end like this: http://www.youtube.com/watch?v=zElsUERTzOU and will cost me about 100$ f***
and it might be that battery got empty.
It's worse than that I'm afraid, there is no JTAG service currently available for the flyer.
is there a possibility that authorized service might still fix it?
They might:
HTC customer service Lithuania
+ 880030766
If you bought in another EU country they are legally required to provide the same warranty cover as is available in the country you bought it.
its from US bestbuy (forever alone face)
tomorrow i'm calling htc, also i contacted few services by email. I will post all info here
gsmserver.com/shop/cables/gsm_products_cables/htc_jtag_adapter_set_9_in_1.php
i think i am going to buy this stuff
That won't help much. You need a RIFF box or similar JTAG adapter (or know someone who does) and you need to locate the JTAG testpoints on the board. What you linked to there is simply the board adapters for the phones listed. If you could find the jtag pin-outs on the board and forward the information to the RIFF box guys they could add support for it.
I recently picked up a secondhand Fascinate for my father and have a desire to root it and flash CM for him. Unfortunately, I've run into a roadblock right off the bat: I cannot connect my computer to the phone via USB. The phone only recognizes it as a charger.
The phone is vanilla and is at latest firmware.
The cables I've tried are LG cables from my own phone.
The computer is Win7 64-bit and has Samsung drivers installed.
Help?
EDIT:
Derp. Perhaps the issue is the cable. I've ordered an OEM cable to test this theory. Thoughts?
Cable could be the issue, I know it has been for some that have used after market USB/data cables. Worth trying in order to rule it out.
I would also strongly suggest using Droidstyles guide. Look in General section. Also, on my device, I sometimes have to "jiggle" the connection to the phone. Sounds odd but it works. You will know right away, pull battery and with ODIN open, plug phone in. Should show up in YELLOW.
Sent from my SCH-I500 using XDA App
Ronjoe said:
I recently picked up a secondhand Fascinate for my father and have a desire to root it and flash CM for him. Unfortunately, I've run into a roadblock right off the bat: I cannot connect my computer to the phone via USB. The phone only recognizes it as a charger.
The phone is vanilla and is at latest firmware.
The cables I've tried are LG cables from my own phone.
The computer is Win7 64-bit and has Samsung drivers installed.
Help?
EDIT:
Derp. Perhaps the issue is the cable. I've ordered an OEM cable to test this theory. Thoughts?
Click to expand...
Click to collapse
Ouch, you may be in a jam. I bought a Fascinate on craigslist. I went home, and fired up Heimdall to install CWM [for cm7], and I got "No device found."
It was charging, but that was all. It would do nothing else. I did get it to connect just a few times, after cleaning the USB connector with a small brush [It was a dental brush actually ]. But it clammed up on me again.
I called up Samsung, they said "You need to have the OEM cable. If it's still not working with the OEM cable we will set up a repair." So I went on amazon and bought the cheapest OEM cable I could find [I think it was $2 or $3, it's OEM samsung, but it's shorter than I thought. :-S ]
I was lucky enough to have 1 month left on the warranty. Unfortunately, you might not be so lucky.
After the repair, my USB worked fine. But then, every morning, I would wake my phone up and it would be in a frozen state. [with about 1 frames per second on the Screen-on animation]
I sent it in again, they replaced the main board, and I have not had any problems since.
If you don't have any warranty [there is a 1-year warranty from the date of purchase], I really hope the OEM cable will work for you. If you're out of warranty, the the OEM cable doesn't work, I guess you might try cleaning the port with a brush, maybe you'll get lucky!
Gl
I've received the replacement cable and it seems to be working. My question is answered.
As a side question, what modifications you guys recommend for the phone in terms of stability and speed? Experience tells me to go for CM7 and CWM, but this phone's developer forum is quite a mess, with different variations of both.
I'd recommend either makelegs' CM7 kangs (in the dev section), or teamhacksung's ICS (find it at rootzwiki). Droidstyle's guide in the general section will get you up and running regardless of what rom you want to go for.
Thanks, k_niv, I've decided to go with makelegs's build. The ICS rom seems a bit... fresh. Keep in mind, this is actually for my father, who doesn't need to be dealing with bugs. He just wants his phone to work the way Android should: fast and Bingfree.
(I'm quite happy with my LG VS910, Gingervolt'd, but don't get me wrong, the Fascinate is damn nice for a year-old phone)
Thanks for the prompt help, my expectations were exceeded on this forum.
Hello,
I have a Verizon Samsung Galaxy S4 SCH-i545. This phone was given to me by my buddy from work to try and fix it for him. I asked him whats wrong with the phone he said he doesn't know he said he went to bed and left it charged and the screen would never come on any more.
I've tried working know good battery
Working wall charger & USB cable
Tried pressing Home button and power button together and holding it
Tried pressing different combinations of home/power vol up/down
Installed KIES thinking the drivers would load
Still cant get this to come on.
I tried doing the same things while having the phone plugged in with the USB to a computer but the only message i got was unable to load drivers for qhusb_dload
I finally found drivers from the forums and installed them, i looked up a few other threads that didn't specify the how-to for the S4 but i downloaded Odin and a stock ROM firmware for the Verizon S4 but still even with the drivers installed Odin was still not able to recognize it. I am unable to find a Guide specifically for this model S4 and after a lot of searching it sounds like i need either some kind of JTAG RIFF or some kind of MicroSD card 16GB or 32GB with some software on it. If i need to solider anything to the board I have no problem in doing so. If i can avoid soldering and do the SD card fix that would be even better or anything else that i need to do in order to get this phone to work again..
Can someone help me out with this S4 qhusb_dload issue or point me to the correct thread so I can get this phone up and going again. The Data is not important to him as he said there's noting important he doesn't already have.
Odin/Download mode is accomplished by holding down Vol- and power and then let go of only power when screen lights up (even if still black) ... that doesn't work?
The the phone work AT QLL? It doesn't seem like it does. If so, you have a chance of getting the debrick image on a micro SD...
...reading over this again, yeah you're hard bricked, going to need JTAG
ToastyZ71 said:
...reading over this again, yeah you're hard bricked, going to need JTAG
Click to expand...
Click to collapse
Hi, yah after reading many other threads i feel like its called a hard brick and not a soft brick as you said.
I was reading about jtag but the device needed is called Jtag Riff and cost over $100, is that the only hardware device i can use in order to fix this phone? If there is another way can someone point me to a thread so i can try to save this phone?
Thank you for your help
mikey323 said:
Hi, yah after reading many other threads i feel like its called a hard brick and not a soft brick as you said.
I was reading about jtag but the device needed is called Jtag Riff and cost over $100, is that the only hardware device i can use in order to fix this phone? If there is another way can someone point me to a thread so i can try to save this phone?
Thank you for your help
Click to expand...
Click to collapse
As far as I know, that's it. Every other method, including USB Jig are for softbrick. - at over $100 for the JTAG Riff, might be better off hitting up swappa for a used/replacement device.
25 bucks on eBay to get it jtag. http://m.ebay.com/itm/181786279537?_mwBanner=1