Hi. I have a problem here. Is it possible to flash new rom directly through bootloader, my activesync is not working properly, and something is wrong with my usb connection - when I connect my device to PC via usb, in bootloading mode - it gets connected and disconnnected about 50 times in one minute, no .RUU is able to recognize it for long enough to complete the instalation. I've tried to reinstall the activesync, did hard reset of my phone, deleted relationships - but no luck. What worries me most is that usb connection problem. It's only with HD2, all other devices connect properly. Anyone knows the answer, what should I do in order to fix that? P.S I always remove sim and sd card, and disable my antivirus programs and firewalls during my flashes....
I bricked it, finally...
And now - I'm stuck...seemed I finally got connected via usb through bootloader for longer than two minutes, so I started fleshing my radio... and it got disconnected after a minute by itself again, in the midllle of the process...Now, there's an upgrade rom code error on green field of my bootloader, telling me to try again, only - I can't do recovery, cause my usb connection gets on/off 50 times a minute, whenever I try to do the recovery .... Any suggestions?
ivona7 said:
And now - I'm stuck...seemed I finally got connected via usb through bootloader for longer than two minutes, so I started fleshing my radio... and it got disconnected after a minute by itself again, in the midllle of the process...Now, there's an upgrade rom code error on green field of my bootloader, telling me to try again, only - I can't do recovery, cause my usb connection gets on/off 50 times a minute, whenever I try to do the recovery .... Any suggestions?
Click to expand...
Click to collapse
Possible solution, you should try different USB ports of your PC.
Always make sure your battery capacity above 50%.
If you don't have HSPL installed, you should only flash the CORRECT OFFICIAL STOCK ROM (go to htc website).
Other alternative, you can flash via micro sd card.
Download the CORRECT OFFICIAL STOCK ROM and extract it using either 7zip or winrar. Find the file named: RUU_signed.nbh
Rename it to: leoimg.nbh
Copy it to the root of micro sd card. Insert it to the phone.
Now, make sure you turn off the phone.
Then, press at the same time, the volume down and power on button, this will bring you to the boot loader.
Follow the onscreen instruction.
Good luck
Thanks for the reply...I have HSPL 2.08, it was fully charged, and was flashing radio 2.12. I was planing to flash a custom rom after words. I've tried about 8 usb ports on my computer, and always the same thing - endless connect/disconnect game, or not connected at all... If I get lucky - it will turn out to be only usb cable, but if I'm not and if it is usb port on my HD2 - I'm doomed, I might as well throw it to the garbage, cause replacement of the motherbord cost as much as new phone ... And, I'm afraid - that's the strongest possibility, I never had a problem charging a phone before this, but a member here explained me that usb port on HD2 has 4 pins, 2 for charging and 2 for data transfer. And that it seems - my data pins are ****ed.. ... So, anyway, I'm gonna try flashing this radio and new rom from sd card, but how am I gonna charge my phone now, in order to do that (I've been trying to establish connection to pc from my bootloader all night, so battery must be low by now) cause when it's turned on and put to charge warning comes up on that black screen: Software update failed, please try again - and the led for charging battery never turns on ?
ivona7 said:
Thanks for the reply...I have HSPL 2.08, it was fully charged, and was flashing radio 2.12. I was planing to flash a custom rom after words. I've tried about 8 usb ports on my computer, and always the same thing - endless connect/disconnect game, or not connected at all... If I get lucky - it will turn out to be only usb cable, but if I'm not and if it is usb port on my HD2 - I'm doomed, I might as well throw it to the garbage, cause replacement of the motherbord cost as much as new phone ... And, I'm afraid - that's the strongest possibility, I never had a problem charging a phone before this, but a member here explained me that usb port on HD2 has 4 pins, 2 for charging and 2 for data transfer. And that it seems - my data pins are ****ed.. ... So, anyway, I'm gonna try flashing this radio and new rom from sd card, but how am I gonna charge my phone now, in order to do that (I've been trying to establish connection to pc from my bootloader all night, so battery must be low by now) cause when it's turned on and put to charge warning comes up on that black screen: Software update failed, please try again - and the led for charging battery never turns on ?
Click to expand...
Click to collapse
Yeah it sounds like your USB port on your HD2 is bad. If your HD2 is still under warranty I flash the official stock ROM via SD card so you are back to complete stock and good for warranty repair. Also so you know if you bought your HD2 secound hand if it was still under warranty when you bought it the warranty is transferable.
Ok people, I've sorted it out ... Lucky me - no faulty usb port on HD2, no faulty cable, and, no faulty HD2 ... I've flashed a different radio from sd card, and also rom, and now - connectivity with my pc is - never better ... Even ActiveSync is working like it hasn't been in 6 months, hahahhhh ... Point is - it was my pc punishing me for playing with it's registry, few nights before ... I was really confused, cause HD7 had excellent connectivity with my pc, but HD2 really bad, so I really thought there was something wrong with my beloved HD2 ... Than, I remembered I've messed with my registry the other night, and deleting some non-existing pocket pc paths in it... So, I repaired my windows on pc, and now everything works like a charm .... What can I say - curiosity can have very high price, sometimes .... But - fortunately, I'm as lucky, as it gets ...
Related
So I recently downloaded the "RUU_Hermes_CINGULAR_WWE_2_1_[1].15.502.3_6275_1.40.30.00_108_Ship" ROM for my 8525, in hopes that it will provide me with a more stable pda/phone enviroment so that I may do the work I need to without having to hard reset every other day or so.
When I try to run the ROM install, I follow all the insturctions but when the update starts to run, it shuts my activesync connection off so the update can't run and throws back an error that it lost connection with the device.
Any Help Here? Thanks
PS: I love the idea of being able to use my 8525 for all my work and play needs, but if this update doesn't help make the device more stable, I will have to sell it for something that doesn't crash this much.
hey..iv got same problem.. i think it maybe cause we are using windows vista (thats the only information i can find about it).. i wanted to update ma rom aswell
I'm using XP Pro.
try running it on another system...if available...
anyone know the solution to this?!
OK, have you installed HardSPL ??
Check my SAFE WM5 upgrade guide, if you follow the procedures in there you should be fine.
Yeah, as far as stability goes most the wm5 roms out of the box aren't going to be the best. with any rom i use sktools to tune it up for performance/stability settings. It does this automatically so you don't have to find various registry keys. So don't think just because you are going to another rom everything will be okay.
Read the wiki, search the threads, you will find answers to all your problems.
As far as you not being able to connect what is your spl number? Also, have you tried hard reseting then connecting or trying another computer. I had the same problem when downgrading a black 2.5 with hard spl 2.1 ( i had to downgrade to send it back to cingular). I ended up just downgrading to the highest version of cingular rom which is branded AT&T. It looked like a pretty good rom but I did not play with it.
he does not need hardSPL(at least i dont think so) he is just runnning an update for another cingular ROM, its still the same CID...try running it on another system, i had this same problem and it worked on another system....
Malik05 said:
he does not need hardSPL(at least i dont think so) he is just runnning an update for another cingular ROM, its still the same CID...try running it on another system, i had this same problem and it worked on another system....
Click to expand...
Click to collapse
HardSPL will protect him against a faulty SPL flash if it occurs, a newer SPL is likely to be in the ROM update aswell as a newer radio possibly. Having the same CID doesnt matter because if the radio or SPL flashing procedure messes up it can create a bricked device VERY easily (corrupt SPL or even a corrupted CID/Radio BL). Besides if he already has HardSPL that would explain why the RUU doesnt reconnect when the device is in bootloader mode.
mrvanx said:
HardSPL will protect him against a faulty SPL flash if it occurs, a newer SPL is likely to be in the ROM update aswell as a newer radio possibly. Having the same CID doesnt matter because if the radio or SPL flashing procedure messes up it can create a bricked device VERY easily (corrupt SPL or even a corrupted CID/Radio BL). Besides if he already has HardSPL that would explain why the RUU doesnt reconnect when the device is in bootloader mode.
Click to expand...
Click to collapse
point well taken...=)
you mention, since he has already gotten HardSPL, why would that mean his device doesnt reconnect in bootloader?
put it in bootloader first and then run the update...
make sure you disable usb connections with active sync put your phone in bootloader and run the update might as well go with WM6 its a lot more stable than any WM5 rom i have played with .
OS crash
I run ROM install then computer shuts itself now my 8525 show hi true color with red/blue/white i tried to hard reset to solve but till hi true color what should i do?
trgrapsonu said:
I run ROM install then computer shuts itself now my 8525 show hi true color with red/blue/white i tried to hard reset to solve but till hi true color what should i do?
Click to expand...
Click to collapse
I've run there updates on my 8525. If the computer is shutting itself down, try another computer. This sounds odd. More of a computer problem then a Tytn Problem.
Malik05 said:
try running it on another system...if available...
Click to expand...
Click to collapse
=) have you even tried it?
I'm having a problem connecting ActiveSync over USB. When I first got the phone I was able to use that connection. Then I set up BT ActiveSync. I believe at the time I could use either USB or BT, but it has been a while. BT sync was so much more convenient for me that I haven't used my USB connection except for charging the phone.
Today I tried to get set up to upgrade the ROM, but ActiveSync doesn't seem to work over USB anymore. I turned off BT on the phone. When I plug it into my laptop's USB port the laptop makes a sound indicating it sees the connection. It makes a different sound when I unplug it. I also see the orange charge light come on on the phone. I usually charge the phone this way when I am on the road since I don't carry the wall charger with me.
I think at one point I installed a river that I fdound here to access the phone in bootloader moder. Other than veryfying the phone connected this way, I never did anything with the driver. IT has been so long that I don't remember the details. Could that be affecting the connection for ActiveSync?
I have made sure my firewall is inactive. In Windows XP Device Manager I see an HTC USB Sync device under Windows CE devices. Would it be safe to remove that device?
Any ideas how I can get USB ActiveSync to work again?
Is it totally crazy to try the ROM upgrade over the BT connection?
emuyshondt said:
I'm having a problem connecting ActiveSync over USB. When I first got the phone I was able to use that connection. Then I set up BT ActiveSync. I believe at the time I could use either USB or BT, but it has been a while. BT sync was so much more convenient for me that I haven't used my USB connection except for charging the phone.
Today I tried to get set up to upgrade the ROM, but ActiveSync doesn't seem to work over USB anymore. I turned off BT on the phone. When I plug it into my laptop's USB port the laptop makes a sound indicating it sees the connection. It makes a different sound when I unplug it. I also see the orange charge light come on on the phone. I usually charge the phone this way when I am on the road since I don't carry the wall charger with me.
I think at one point I installed a river that I fdound here to access the phone in bootloader moder. Other than veryfying the phone connected this way, I never did anything with the driver. IT has been so long that I don't remember the details. Could that be affecting the connection for ActiveSync?
I have made sure my firewall is inactive. In Windows XP Device Manager I see an HTC USB Sync device under Windows CE devices. Would it be safe to remove that device?
Any ideas how I can get USB ActiveSync to work again?
Is it totally crazy to try the ROM upgrade over the BT connection?
Click to expand...
Click to collapse
have you tried changing the setting on your phone "USB to PC"? I would try this first before digging to deep
slavetolustnyc said:
So I recently downloaded the "RUU_Hermes_CINGULAR_WWE_2_1_[1].15.502.3_6275_1.40.30.00_108_Ship" ROM for my 8525, in hopes that it will provide me with a more stable . . . When I try to run the ROM install, I follow all the insturctions but when the update starts to run, it shuts my activesync connection off so . . .
Click to expand...
Click to collapse
You may want to try using the Hard SPL v7 and then install your ROM. I did that and all went smooth as silk - six times now. I have been browsing ROMs to see which one suited my needs an personality, and it has been fun. You can find that on my FTP site at ftp://xda:[email protected]/xda_dlz/
This is a dynamic IP Address from a cable modem so two things are true
1. It is subject to change at any time.
2. It is not as fast as some of these speedy servers
But, I do know where it is.
shogunmark said:
have you tried changing the setting on your phone "USB to PC"? I would try this first before digging to deep
Click to expand...
Click to collapse
I had tried this yesterday and checked the Enable advanced network functionality box. Today I unchecked it and suddenly the PC saw a new USB device (HTC Sync USB, I think). It still wouldn't sync automatically so I manually executed /windows/repllog.exe. This time it connected.
Some observations:
- After the connection was established the the name of my 8525 was changed to something different (something like WM_ComputerName1, Where ComputerName is my computer's host name). I changed the name back and was able to re-invoke repllog.exe and sync with the old name.
- If I disconnect the USB cable from the phone and plug it in again ActiveSync doesn't connect until I manually run repllog.exe. It does work when I run the exe on the phone manually.
I went ahead and started the upgrade process after connecting by running repllog.
Executing the RUU file from the HTC site first put SPL 1.11 on the phone and left the phone in bootloader mode (with the tricolor screen). I left the phone with bootloader screen and followed the instructions (although by now ActiveSync had shut down so the part about the AS connection that the installer asked for was not true). The progress bars appeared on both the phone and the PC. It took a few minutes to complete, but the update was successful.
After the upgrade I was able to sync over USB without any problems. I am now syncing my contact from Lotus Notes and setting things up to my liking. Once I got over the USB connection problem everything worked fine!
im a tech for a sprint affiliate store and i have a customers mogul that she got into bootloader...normally what i would do in this situation is disable usb connection in AS...plug in the phone...wait for the drivers to install and use UNI_ExitBootloader.exe to get it out of bootloader...
but for some reason with this phone when i plug it up via usb...it still says serial, instead of switching to USB at the bottom and the program nor the computer can read the device
i have a test mogul here...and when i put it into bootloader...it says(rom 3.45 offical sprint windows 6.1)
"TITA100
SPL-2.07.0000
CPLD-9"
and it unlocks fine
the mogul that wont get out of bootloader says(rom 3.35 official sprint)
"TITA100
SPL-1.04.0000"
and thats it...
im stumped...
Run titan_exitbl instead of UNI. A quick forum search and you'll find it. See if that works for you.
ive tried that as well...the problem is when i connect the phone to the computer its supposed to go from serial mode to usb mode...and it doesnt...so the computer doesnt download the drivers and hence wont connect using either program...
ive scoured many forums for hours and have not been able to find a solution or even a description of my particular problem...
thank you for the suggestion but being im not a noob this doesnt seem like your regular search and find your answer type of problem
justincredible said:
ive tried that as well...the problem is when i connect the phone to the computer its supposed to go from serial mode to usb mode...and it doesnt...so the computer doesnt download the drivers and hence wont connect using either program...
ive scoured many forums for hours and have not been able to find a solution or even a description of my particular problem...
thank you for the suggestion but being im not a noob this doesnt seem like your regular search and find your answer type of problem
Click to expand...
Click to collapse
Run MTTY to exit BL.....
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
BTW the 2.07 is the re-locker from NO2chem....
and no dice on that solution as well...just reads com1 and com2 under ports where you are supposed to be able to select USB
This is kind of a stupid question to ask....but did you try enabling usb connections in activesync and connecting it?
yes i did...wouldnt connect...but it will connect on my broke mogul and the working mogul i own...
which bugs me because i still dont think its a physical issue(like a broken USB port) because the customer was having problems sending SMS called tech support and they tried some stuff with her over the phone and she got stuck in bootloader...
im assuming this is a lost cause...but i try to repair as many phones as i can instead of just tossing people reconditioned ones...even though my store technically isnt a repair center...
thanx again for everyones suggestions...
and if anyone else has a clue wtf is going on lol...
please feel free to let me know
Flash from SD?
Since it is possibly dead anyway, how about try flashing from SD card as it will exit bootloader and reboot as its last ac ??? Can not hurt any worse;-)
so i need to take the installer file...get the RUU_signed.nbh file extracted from the ROM...rename it to TITAIMG.nbh...format the SD card to fat32...pop that baby in and see what happens?
thanx for that suggestion i totally forgot about that...
well good idea but still no dice...
i installed th ROM via SD card...it worked!...
fixed the SPl and CPLD errors fixed...so i know the ROM got loaded correctly...
the test mogul and the broken one look exactly the same in bootloader...yet i STILL cant get my comp to see the device...its still stuck in serial mode and wont switch to USB mode and i cant get it out of bootloader
edit:
wait...i turned the phone off...plugged it up via usb...turned the phone on and the damn thing worked!
phone booted right up...which is weird because i turned it off and turned it back on after i reinstalled the ROM from the SD card...
thank you guys for all your help...
you just really educated about 30+ TSRs from sprint affiliate stores in illinois, indiana, michigan, iowa etc etc
What does it say in bootloader exactly??? List everything on the screen.... sounds like if it works with the phone plugged in via USB, that you have the wrong bootloader on it.... Does it boot up without being plugged in??
well looks like i gave out the props a lil too soon lol...
im back to square one...installed ROM from SD card...took battery off...put it back in...turned phone on....if its plugged up via USB it'll boot up...add the extra sprint crap on it...as soon i unplug it and restart it goes right back to bootloader...and my comp wont see it as a USB device yet and still it'll see 2 other moguls i have chillen around my house
TITA100
SPL-2.07.0000
CPLD-9
is what it says...
omg this is nuts lol
if i leave the mogul unplugged from the USB cable after reinstalling the ROM from the SD card it just goes right back to bootloader...
it wont take a charge...nix that it took 5 minutes b4 it would accept a charge...
theres definately something wrong with the USB port...has to be...
It sounds like you fixed the software issues but I agree there has to be something up with the USB
the thing that puzzles me is that the usb port doesnt appear to be damaged at all...its still attached to the board...none of the pins are bent or broken...theres no water damage...
im baffled
justincredible said:
well looks like i gave out the props a lil too soon lol...
im back to square one...installed ROM from SD card...took battery off...put it back in...turned phone on....if its plugged up via USB it'll boot up...add the extra sprint crap on it...as soon i unplug it and restart it goes right back to bootloader...and my comp wont see it as a USB device yet and still it'll see 2 other moguls i have chillen around my house
TITA100
SPL-2.07.0000
CPLD-9
is what it says...
Click to expand...
Click to collapse
1st, get some compressed air and blow out the USB port, and get a different cable.... try connecting it now - hopefully something was causing a bad connection....
In bootloader screen does it change from serial to USB on the phone screen when you plug it in?? If it does you can get the official Sprint update and run it while the phone is in bootloader, it should finish just fine..... try this and report back....
i tried compressed air...didnt change anything...the phone will charge but wont switch from serial to usb...its not the cable because i have a my working mogul and a test mogul here and both worked perfectly...
the phone will boot up and work if its usb port is in use(charging, syncing) but as soon as i disconnect the cable and restart for any reason it goes right back to bootloader...and it will not boot up at all if the usb port isnt in use...
like i said...this is easily the most retarded seemingly unfixable mogul break down ive ever seen...
its very interesting in a werid kinda dorky way...this mogul is impervious to traditional bootloader fixes lol
So try this, copy NueSPL to the SD card, and then boot the phone and copy it to the phone. Then run the nuespl so it upgrades the spl to nuespl 2.47. You already have the the 3.56 ROM and the 3.42 radio on it right???
Heres the link to nuespl nueSPL-2.47.rar
what radio version is installed?
reading your first post, SPL 1.x should not have been on the broken phone. I wonder if it failed during the 3.X ROM update. Maybe she tripped over the USB cable while flashing.. I've done it.
az ill go ahead and try that when i get the phone back...she didnt feel like waiting another day and i could def understand that...so when the exchange is done im going to bring it back home and play mogul dr...
and dcd she hasnt updated her ROM at all...it was the stock 3.35 rom that came preinstalled when she got it...and no diss to her but i know her and shes not that technically inclined...but ill note the radio and get back to you...
this is an issue resolution that could help a lot of people...
i appreciate all you guy's help and suggestions...
Yeah, or at least I think so...
Everything was working fine till yesterday morning. I checked my phone and it didnt charge anything at all after a whole night connected to the plug.
Actually, the USB port "works", but the phone itself takes a good damn time to recognize it as if it was charging, and it will never detect the USB connected to my PC. Also, the only way I can possibly charge my phone is by connecting to my PC for some reason.
Those errors happened just a day after I flashed my droid to BB 52 and installed Ultima 4, a mod I found here.
So, I was guessing if anyone could help me out, maybe trying to flash the BB back to my 49 via XRecovery (wich I did not find any possible ways 'til now), or just "rebuilding" the USB drivers via phone. I can access my SD card via wi-fi still, so I think there could still be a salvation for my problem
Does anyone have any idea?
Also, no, I can't even access the flash mode anymore. And something I found here, and that was quite strange, is the fact that if I replace my battery while connected, the USB green LED will remain active, but my phone won't boot in any possible ways 'til I remove the USB cable. (wtf.)
Someone just needs to upload you a xrecovery backup.
Can anyone give this dude a hand?
Well, the day before it occurred to me that I'd like to install a custom ROM, therefore I went on to plug my phone into my PC and for my surprise, the phone didn't pop that MTP warning and the PC did not recognize it.
So I went around and changed USB ports, cables and PCs, same thing.
Decided to try Mass Storage mode, when I press the START button and put in the cable it goes back into the main start screen.
So I went on and tried that *#7284# trick people used since apparently 4.0.3 bugged some crap stuff in the phone, no success either.
Strangely enough I can connect the "pendrive dongle" and it will map pendrives.
Well, I don't have my phone rooted or with SU so that means CWM from app store won't be able to install the recovery module, and I can't install... you get the picture.
Nor ODIN nor HEIMDALL will recognize my phone in recovery mode, wich suggests that the data lanes on my phone went somewhat dead.
Finally, any cable I plug in the phone says it's charging my device, wich leads me to belive that the usb port is dead.
Anyone had this issue?
Anyone can confirm me I'll have to take it to Sammy's assistance?
Sure looks like the USB is dead/dying.
Sent from my digital submersible hovercraft.
So I got one more question, can I root and/or install CWM so I do not stay dependent of the USB to update it or I do need to plug in the USB to install CWM through ODIN?
Several problems
It can be several reasons
1.the usb is dead buy new
2. try factory resetting the device
3. install kies on pc it will install all the drivers that you need
4.your usb port(of the phone) is dead
I had the same problem pc was saying "USB cannot be recognized" I TRIED EVERYTHING from factory resetting, changing pc usb ports, changing usb, changing kernel, roms, trying on other pc, reinstalling kies and drivers but nothing. The problem was in the usb port on the phone where you connect the charger on the phone. That part is weak and so you have to change it. Take to customer service with your warranty and they will fix it without charging anything just tell them your problem and say that you read that most of the galaxy s2 users have this problem and that you didn't touch the hardware of the phone
Angelkom said:
It can be several reasons
1.the usb is dead buy new
2. try factory resetting the device
3. install kies on pc it will install all the drivers that you need
4.your usb port(of the phone) is dead
I had the same problem pc was saying "USB cannot be recognized" I TRIED EVERYTHING from factory resetting, changing pc usb ports, changing usb, changing kernel, roms, trying on other pc, reinstalling kies and drivers but nothing. The problem was in the usb port on the phone where you connect the charger on the phone. That part is weak and so you have to change it. Take to customer service with your warranty and they will fix it without charging anything just tell them your problem and say that you read that most of the galaxy s2 users have this problem and that you didn't touch the hardware of the phone
Click to expand...
Click to collapse
Warranty has already expired.
Kies was installed on the PC, ODIN gives no info @ COM port.
I wanted to connect it just to root and install CWM so I can swap ROMs as much as I want.
Thing is, the customer service wants 1 week to assess the issue and probably 100USD to fix it.
So for some god-knows-why reason my phone decided to conect to MTP while charging, I quickly restarted it into revocery mode and flashed CF_Root w/ CWM5.5.
Successful!
Bloody USB thingy!
Now I can start messing around with the phone.
Anyone has a n00blet guide on ROMs?
I was thinking about moving to CM 10.1, one of those nightlies running 4.2.2.
This is the one I used >> CF-Root-SGS2_XW_OXX_LPE-v5.5-CWM5
Can anyone suggest actions?
For future you should change your USB-Port. Here we get one for about 15 € (about 20 $) in ebay. It's very simple to change and then you have a full working phone again. Just watch the Videos on Youtube and everyone can do this. Hope I could help!
Hello Everyone,
I was worndring if it is in some how possible to upgrade my GT-I9070 from gingerbread 2.3.6 to Kitkat or other custumized rom without having to use odin.
I have a problem with connecting my phone to the my pc, my laptop won't regonize it, I think is a hardware problem.
Thanks a lot
Yassine
darkclub said:
Hello Everyone,
I was worndring if it is in some how possible to upgrade my GT-I9070 from gingerbread 2.3.6 to Kitkat or other custumized rom without having to use odin.
I have a problem with connecting my phone to the my pc, my laptop won't regonize it, I think is a hardware problem.
Thanks a lot
Yassine
Click to expand...
Click to collapse
Not unless you are already rooted. Does the PC not recognize that you have plugged it in at all or does it just not load the drivers correctly? Best way to tell is to open your Device Manager and plug in the phone. the DM should reload and show something, whether an error or not. If it does not blink out and reload when you plug / unplug the phone, then it's either a hardware issue with the phone's USB port, a bad cable, or bad USB port on PC. And it is possible for a phone to charge correctly, but have issues connecting to a computer if the data pins are messed up. If it IS the phone's port, the repair isn't that bad and could be handle with some patience and simple tools as this one does not involve soldering. You'd need this:
http://www.amazon.com/Samsung-Galaxy-Advance-GT-i9070-Replacement/dp/B00B5OS2LY
https://www.youtube.com/watch?v=_0nuBDAuLm8
You won't find a better guide than that, that guy is amazing at teardowns.
es0tericcha0s said:
Not unless you are already rooted. Does the PC not recognize that you have plugged it in at all or does it just not load the drivers correctly? Best way to tell is to open your Device Manager and plug in the phone. the DM should reload and show something, whether an error or not. If it does not blink out and reload when you plug / unplug the phone, then it's either a hardware issue with the phone's USB port, a bad cable, or bad USB port on PC. And it is possible for a phone to charge correctly, but have issues connecting to a computer if the data pins are messed up. If it IS the phone's port, the repair isn't that bad and could be handle with some patience and simple tools as this one does not involve soldering. You'd need this:
http://www.amazon.com/Samsung-Galaxy-Advance-GT-i9070-Replacement/dp/B00B5OS2LY
https://www.youtube.com/watch?v=_0nuBDAuLm8
You won't find a better guide than that, that guy is amazing at teardowns.
Click to expand...
Click to collapse
Dude really thankful,
As you say, the PC dosn't recognize that the phone is plugged at all, I try all the usb port on my laptop, different cable, and even different laptop and the same problem keep comming up.
I tried also to reboot in odin mode to see if my laptop detecet anything, but nada, nothing in the DM.
Also, like you expect, it can charge but no data connection, and whene it turned off and I plug it it automaticly turned on by itself.
I pretty convinced that it usb port is screwed.
So, to install a rom my phone have to be rooted!! no way to root it from the recovery mode?!
Thanks again
darkclub said:
Dude really thankful,
As you say, the PC dosn't recognize that the phone is plugged at all, I try all the usb port on my laptop, different cable, and even different laptop and the same problem keep comming up.
I tried also to reboot in odin mode to see if my laptop detecet anything, but nada, nothing in the DM.
Also, like you expect, it can charge but no data connection, and whene it turned off and I plug it it automaticly turned on by itself.
I pretty convinced that it usb port is screwed.
So, to install a rom my phone have to be rooted!! no way to root it from the recovery mode?!
Thanks again
Click to expand...
Click to collapse
You can try to clean your USB port of the phone with some compressed air, in case some pocket lint got in there too. Doesn't take much to mess these things up, unfortunately. But yea, I doubt there is a way to root it in the stock recovery as most Samsung phones don't have this option. It'd take less time to just fix it probably then figuring out how to jump through all the other hoops to find a way around it.