[Q] Help me restore to stock settings - Fascinate Q&A, Help & Troubleshooting

I have a little problem and could use some help. I was running superclean 2.9.2 and attempted to switch over to the community rom. Before flashing the rom I downloaded the stock CI500_VZW_DL09_ECLAIR.tar.md5 file and attempted to load that with Odin(yes i chose pda). I have used Odin multiple times in the past w/out issues. Well this time my screen went blank on the Odin was stuck on param.lfs. When i disconnected my phone it now boots to the screen with a phone, exclamation point and a computer. I closed Odin restarted my computer and tried again with the same result. I can still access the download mode and CWM. When I try to complete a nandroid restore the phone goes through the whole process and then when I click to reboot I get the same screen as above. My next step was to download DI01package3.tar.md5. I tried pushing this with Odin and it got stuck on sbl.bin. Please help me get my phone back.

As you have unfortunately discovered, Odin is unreliable. Try to use Heimdall by following the instructions in this thread.

Im in the process but when I select the USB drop down menu all I see is unknown device, I do not see SAMSUNG android composite ADB device, or Samsung composite usb driver.

Could be your download was corrupted...?
Sent from my SCH-I500 using XDA Premium App

I followed the Heimdall thread but I can not get it to work as published. I downloaded all the files and was able to install the Samsung composite usb driver and then launched heimdall-frontend and I can check the box and use the pit file I installed, but the tar.md5 files are not extractable so I dont know what values to put in the boxes.

OK i figured out how to extract the .tar contents and filled them in the appropriate section of frontend and i hit start, which is soon followed by failed to retrieve config descriptor any more suggestions?...WEll I kept on entering download mode and reloading the values for frontend and finally it worked. Thanks for the help, greatly appreciated! No its time to try to get the community rom loaded.

Related

ODIN won't pick up vibrant in download mode

Hey everyone-
I'm trying to ODIN my vibrant back to stock from eugene373's froyo rom, the one with latest one (r3 i think) with the supposedly working clockwork mod (it didn't for me :-/). Anyway, I'm able to get the phone into download mode ONLY by pushing power on and holding volume -, I've already tried turning it off and plugging in the cable and it doesn't work for some reason, but whenever it enters download mode ODIN doesn't seem to pick it up. Oddly enough, ODIN will pick up my vibrant as COM6 when it's powered on, but that's only time I can get it to work. And my vibrant IS NOT hardware locked. Thanks for any help in advance.
-bobofosho123
bobofosho123 said:
Hey everyone-
I'm trying to ODIN my vibrant back to stock from eugene373's froyo rom, the one with latest one (r3 i think) with the supposedly working clockwork mod (it didn't for me :-/). Anyway, I'm able to get the phone into download mode ONLY by pushing power on and holding volume -, I've already tried turning it off and plugging in the cable and it doesn't work for some reason, but whenever it enters download mode ODIN doesn't seem to pick it up. Oddly enough, ODIN will pick up my vibrant as COM6 when it's powered on, but that's only time I can get it to work. And my vibrant IS NOT hardware locked. Thanks for any help in advance.
-bobofosho123
Just FYI check to make sure, you swtich USB ports on the PC and also make sure you have all the right drivers installed. Looking at the pics, I see that you are not selecting the rite options. All you need is the PIT & the PDA files selected.
Click to expand...
Click to collapse
chichu_9 said:
bobofosho123 said:
Hey everyone-
I'm trying to ODIN my vibrant back to stock from eugene373's froyo rom, the one with latest one (r3 i think) with the supposedly working clockwork mod (it didn't for me :-/). Anyway, I'm able to get the phone into download mode ONLY by pushing power on and holding volume -, I've already tried turning it off and plugging in the cable and it doesn't work for some reason, but whenever it enters download mode ODIN doesn't seem to pick it up. Oddly enough, ODIN will pick up my vibrant as COM6 when it's powered on, but that's only time I can get it to work. And my vibrant IS NOT hardware locked. Thanks for any help in advance.
-bobofosho123
Just FYI check to make sure, you swtich USB ports on the PC and also make sure you have all the right drivers installed. Looking at the pics, I see that you are not selecting the rite options. All you need is the PIT & the PDA files selected.
Click to expand...
Click to collapse
yeah I tried that to, didn't work. I used the very first JFD firmware from the backup firmware thread and the .512 pit file as well and that was it, and for some reason ODIN still wouldn't pick up my vibrant. fyi, i was actually able to get it to flash to an odin copy of JI8 a couple hours ago, but now I keep getting a bunch of FC's and ODIN yet again isn't sensing the vibrant in download mode.
Click to expand...
Click to collapse
Sorry to break it to you but its most likely an issue with your computer. Try going to the local library and use one of theirs.
Try getting into download mode first than starting up Odin. If that doesn't work try it in reverse.
Just my .02, but I noticed that if I have Kies open, Odin wont see my Vibrant... Dont know if that is the cause of your problem or that you even have Kies at all.
I'm going to go with make sure you have the correct drivers installed.
If you don't have the drivers
Hit up this thread for the drivers.
Sometimes odin doesn't recognize my phone and I unplug the usb and plug it back in and it pops up..do this while still in download mode and odin open..
Sent from my SGH-T959 using XDA App
constomy said:
Sometimes odin doesn't recognize my phone and I unplug the usb and plug it back in and it pops up..do this while still in download mode and odin open..
Click to expand...
Click to collapse
Agreed. I have to do this every time, but it also works every time. As soon as I plug the USB back in Odin will show a com port has been connected, and then I'm good to go with the flashing. I'm using Windows 7 64 bit.
Dave08 said:
Agreed. I have to do this every time, but it also works every time. As soon as I plug the USB back in Odin will show a com port has been connected, and then I'm good to go with the flashing. I'm using Windows 7 64 bit.
Click to expand...
Click to collapse
Yeah I have to do it every time also...I'm running vista...
Sent from my SGH-T959 using XDA App
Dave08 said:
Agreed. I have to do this every time, but it also works every time. As soon as I plug the USB back in Odin will show a com port has been connected, and then I'm good to go with the flashing. I'm using Windows 7 64 bit.
Click to expand...
Click to collapse
I have also had success with this method. Closing odin and reopening before I re plug is what I have done and have had no issues. Vista Ultimate 64.
I need help. My vibrant is soft bricked. I can access 2e recovery but cannot get into CWM at all. I dont even have the update.zip in my internal. I can get into download mode but odin will not recognize my device. (believe me when I tell you Ive tried it all on multiple computers using different cables, usb slots, etc.). I actually fell asleep at my desk last night trying it all. My question is, can I somehow access the internal storage of my vibrant through my pc possibly ? In order to place the cwm update.zip in the root folder then enabling me to "reinstall packages" through 2e recovery ?
Any help is much appreciated. This is killing me.
Profound said:
I need help. My vibrant is soft bricked. I can access 2e recovery but cannot get into CWM at all. I dont even have the update.zip in my internal. I can get into download mode but odin will not recognize my device. (believe me when I tell you Ive tried it all on multiple computers using different cables, usb slots, etc.). I actually fell asleep at my desk last night trying it all. My question is, can I somehow access the internal storage of my vibrant through my pc possibly ? In order to place the cwm update.zip in the root folder then enabling me to "reinstall packages" through 2e recovery ?
Any help is much appreciated. This is killing me.
Click to expand...
Click to collapse
This helped me:
Originally Posted by fishman0919
Can you try flash my Odin image of KB5 with Odin v1.7 - LINK
It at the bottom of the post. Make sure "Re-Partition" is checked.
It will drop you into Voodoo recovery after... do a factory wipe and then reboot.
Click to expand...
Click to collapse
Sounds like driver issues.. There was a similar post about this the other day. Here is a link that could help you.
http://forum.xda-developers.com/showthread.php?p=26861898
Sent from my SGH-T959 using XDA
Profound said:
I need help. My vibrant is soft bricked. I can access 2e recovery but ...................
Click to expand...
Click to collapse
I gotta get my phone on a charger, so will have to wait and search for the post in a little while, but another person had this issue, and had luck with a windows software that was like an android file explorer or something. Was able to save all his pictures and files. Surely you could also use it to transfer update.zip back to the internal sd.
I will look for that post and get back to you.
Update: this is the thread I was referring to. Hope this helps. I haven't used it, but if it can copy files from the internal, theres the chance it will copy files TO the internal... Good luck!
http://forum.xda-developers.com/showthread.php?p=26783165
Sent from my SGH-T959 using XDA
I can never get ODIN to recognize my phone on Windows7. I always have to use my old PC running XP. Also other devices being plugged into the PC have been known to bork up ODIN.
Good luck!
Sent from my SGH-T959 using xda premium
This package includes:
Repartitioning: Repartition to stock JFD
Reloading: IBL/PBL, PARAM, SBL, SBL2, Kernel, Recovery, FactoryFS and modem
formatting:Cache, DBdata, Data
You may use this code to reformat the SDCard *2767*3855# There is no way to do this from Download Mode. The code will leave the EFS untouched.
This package does not wipe:
SDCard (where your pictures are stored)
EFS(Where your serial number and carrier information is stored)
Instructions:Get the latest version of java here: http://java.com/en/download/installed.jspPut your phone into "Download Mode"Run the program once, and if it does not work, then check the "Flash Bootloaders" checkbox and flash again
Your device will end up as it came from the factory with UVJFD
Download:
Download UVJFD Heimdall One-Click
http://teamkomin.com/Vibrant/T959-UVJFD-Stock-One-Click.jar
Credits:
Thanks to gregc2009 for pointing me at the firmware
This package contains bootloaders from this link: http://forum.xda-developers.com/showthread.php?t=1117990
This package contains UVJFD firmware from this link: http://rootzwiki.com/showthread.php...pps-*-everything&p=11409&viewfull=1#post11409
This package is intended for:
Linux 32
Linux 64
OS-X Leopard
OS-X Snow Leopard
OS-X Lion
Windows XP
Windows Vista
Windows 7
REPARTITIONING ISSUE WITH HEIMDALL 1.3.0
Heimdall currently has an issue with repartitioning. 99% of the time you will not need to repartition. Failure to follow these directions can possibly lead to bricking:
Do not flash bootloaders if you see this message:
Local and device PIT files don't match and repartition wasn't specified!
This message means your partition tables do not match the firmware.
You will need to use Linux to repartition with this firmware package. Install Ubuntu. In Linux, you can copy-pasta this into the terminal to correct the repartitioning problem and then flash bootloaders. http://forum.xda-developers.com/showpost.php?p=17485056&postcount=23
Check this out. Its a way to fix without Odin.
This post is from vibrant dev thread, from AdamOutler
SGH-T959 ICS Gummy 1.2

Stuck at Vibrant Screen

Hello everyone,
I have been trying to find a way to get out of the Vibrant screen for my phone.
This happen by me having the Obsidian 4.2 installed with Black Froyo, and I was trying to restore to get the Sims 3 and Thinkfree office because it was not available when I flashed my phone.
I have a backup using ROM Manager on my laptop. I am using a Mac, and I have Parallels installed with XP. Problem is I have ODIN installed and been trying to have ODIN recognized the Vibrant in order to start the process, but it has not recognize the device. I thought I had all drivers installed, and I would appreciate any help.
The device is recognized when I have it in the Recovery mode, but not in download mode.
Odin is super finicky but this process usually works. Plug your phone into your usb port while it's still off. Bring up odin but don't put the files you want in it yet. Now boot your phone into download mode. After the com port comes up in odin load the files into thier proper fields and install. Hope that helps.
Sent from my SGH-T959 using XDA App
if you can get to clockwork recovery, you can mount your phone to your computer (the option that says USB, like the 2nd or 3rd option). You could then move a rom with kernel to your phone and flash it.
I think your problem is you were trying to go from 2.2 to 2.1 (nandroids do not restore the kernel, hence it will hang at the Vibrant screen). Perhaps you have voodoo or another lag fix and didnt disable it?
Also, my noob version in my signature show the proper steps for ODIN, and has a video.
Thank you the process work. I had Windows running on Parallels and it messed everything up. Had to reboot only with Windows though. i just resetted everything until I become more familiar with the process.

HELP!

I might have accidentally bricked my SGS 2. I get a screen saying:
"firmware upgrade encountered an issue. Please select recovery mode in kies and try again"
with a mobile phone and a computer logo with a Yellow triangle in between.
I know abt Rooting and ROM flashing etc and has been doing it for the last couple or years.
I flashed Franklin's XXKG3 Kernels, and before I could flash Chainfire's XXKG3 kernel, the USB ports refused to recognize my handset. I can still go into download mode but the Odin or Samsung Kies etc. won't do nothing.
Keeps saying "USB Device not recognized"
Please help!!!!
leo13aug79 said:
I might have accidentally bricked my SGS 2. I get a screen saying:
"firmware upgrade encountered an issue. Please select recovery mode in kies and try again"
with a mobile phone and a computer logo with a Yellow triangle in between.
I know abt Rooting and ROM flashing etc and has been doing it for the last couple or years.
I flashed Franklin's XXKG3 Kernels, and before I could flash Chainfire's XXKG3 kernel, the USB ports refused to recognize my handset. I can still go into download mode but the Odin or Samsung Kies etc. won't do nothing.
Keeps saying "USB Device not recognized"
Please help!!!!
Click to expand...
Click to collapse
Might help to reinstall KIES or try another computer.
Keeps saying "USB Device not recognized"
USB drivers problem remove Kies totally and reinstall .
Connect in mass storage mode and let windows find drivers .
That fails its broken phone .
jje
you broke your phone.
buy another SGS II
You can always try using a USB JIG to put the phone in download mode.
leo13aug79 said:
Keeps saying "USB Device not recognized"
Click to expand...
Click to collapse
Uninstall the Samsung USB Driver from Control Panel
START/Control Panel/Programs and Features
Select "SAMSUNG USB Driver for Mobile Phones" and then uninstall
reboot your PC and then re-install the Samsung USB Driver from:-
C:\Program Files\Samsung\Kies\USB Driver
and run "SAMSUNG_USB_Driver_for_Mobile_Phones.exe"
Doing that will make sure there is no USB driver corruption.
"firmware upgrade encountered an issue. Please select recovery mode in kies and try again"
Click to expand...
Click to collapse
I had the same problem on my SGS4g after updating to a leaked 2.3.4 rom, which would not make phone calls. Tried to use heidmall to downgrade by loading a new rom. After installing the usb driver as described here http://forum.xda-developers.com/showpost.php?p=14798367&postcount=1 . After reboot I get the error screen <phone..!..Computer> "firmware upgrade encountered an issue. Please select recovery mode in kies and try again". I then took the following steps.
I came across this site: http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Bricked_Screen Under the bricked section it mentions a couple things to try. I the reboot cycle with a couple of times and kept on getting the same screen. Still no go.
I took Odia's advice an did a complete removal of all usb drivers as mentioned and reinstalled kies. This was key in getting odin to recognize the phone again.
My solution:
I try Odin again to try to get it to recognize my phone. I open odin with the usb connected in this state and it is not recognized. I pull battery, it boots to error screen. I restart odin and then plug in the usb and it is recognized. I was then able to load my pit, pda, phone, csc back onto the phone with odin. The first time it tried to load the data it failed, the second time it worked!
Interestingly I never got the "Download Screen". I was still on the mentioned error screen, yet odin was able to still see the phone. The status bar still showed up on the error screen as the fresh rom was being loaded.
I thought I was totally bricked, but this method worked in my case. Hope something similar might work for you.
I still don't know I would get this error screen and have to go through this after loading the required usb driver for heimdall? Any ideas?
OMG! It's WORKING!
Thanks a lot to you all guys for the co-operation....
So, what did I do???? I uninstalled Kies and re-installed a couple of times but it won't access it. Tried Odin in all possible ways, No success. While playing and after ordering a "Jig" from some1 in USA,
I thought of something else and while the phone still being connected with the pc, I ran SuperOneClick, but it went on saying waiting for the device,.... I accidentally or in frustration hit the "HOME" button and it started doing something, USB drivers and Modem drivers installed on PC. Then I started Odin and the port went "Yellow". And I flashed it with the XXKG3.....
OMG! I'm so much relieved!!!!!!!! thanks God
thank you all too
Love your SGS2 and love God! Bless you all!
fvnktion said:
I had the same problem on my SGS4g after updating to a leaked 2.3.4 rom, which would not make phone calls. Tried to use heidmall to downgrade by loading a new rom. After installing the usb driver as described here http://forum.xda-developers.com/showpost.php?p=14798367&postcount=1 . After reboot I get the error screen <phone..!..Computer> "firmware upgrade encountered an issue. Please select recovery mode in kies and try again". I then took the following steps.
I came across this site: http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Bricked_Screen Under the bricked section it mentions a couple things to try. I the reboot cycle with a couple of times and kept on getting the same screen. Still no go.
I took Odia's advice an did a complete removal of all usb drivers as mentioned and reinstalled kies. This was key in getting odin to recognize the phone again.
My solution:
I try Odin again to try to get it to recognize my phone. I open odin with the usb connected in this state and it is not recognized. I pull battery, it boots to error screen. I restart odin and then plug in the usb and it is recognized. I was then able to load my pit, pda, phone, csc back onto the phone with odin. The first time it tried to load the data it failed, the second time it worked!
Interestingly I never got the "Download Screen". I was still on the mentioned error screen, yet odin was able to still see the phone. The status bar still showed up on the error screen as the fresh rom was being loaded.
I thought I was totally bricked, but this method worked in my case. Hope something similar might work for you.
I still don't know I would get this error screen and have to go through this after loading the required usb driver for heimdall? Any ideas?
Click to expand...
Click to collapse
I love you man! You saved my phone and me!
So what have we learnt today? Don't go screaming "brick!" everytime you encounter a problem
I had a same issue yellow triangle between Phone and PC symbol...
followed this step .. http://forum.xda-developers.com/showthread.php?t=1274337
just did like this on very first step to get into odin mode hold vol down and power for longer then usual to get into odin mode and by pass that yellow triangle between Phone and PC screen and then follow rest of it same and easy as right clicking on desktop LOL!
From my experience, only true brick I encountered was when I messed with boot loaders. If the screen shows anything at all, Odin will recognize it. Glad to hear it's fixed
Sent from my GT-I9100 using XDA App
Odia said:
Uninstall the Samsung USB Driver from Control Panel
START/Control Panel/Programs and Features
Select "SAMSUNG USB Driver for Mobile Phones" and then uninstall
reboot your PC and then re-install the Samsung USB Driver from:-
C:\Program Files\Samsung\Kies\USB Driver
and run "SAMSUNG_USB_Driver_for_Mobile_Phones.exe"
Doing that will make sure there is no USB driver corruption.
Click to expand...
Click to collapse
I´d tried to upgrade my Infuse SGH-i997 (AT&T) but I did something wrong and now the cell phone no work.
When it turn on says:
"firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
The computer recognize the cell phone but I don´t know what else I can do.
Any suggestion?
Can you get into download mode? If yes then reflash stock firmware using Odin
Sent from my GT-I9100 using Tapatalk
A bricked phone is a phone which will not respond. It maybe a soft brick or hard.
If you can get into download or recovery all you have to do is reflash. Wipe data & Cache. You will be up and running. If your phone is not recognised by your computer then reinstall kies.
Sent from my GT-I9100
Yep. Infuse Q&A (You're in the wrong section).
anjimgo said:
I´d tried to upgrade my Infuse SGH-i997 (AT&T) but I did something wrong and now the cell phone no work.
When it turn on says:
"firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
The computer recognize the cell phone but I don´t know what else I can do.
Any suggestion?
Click to expand...
Click to collapse
Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Moving to Q&A
Well, I got this same Firmware upgrade error. I can't get the computer to see it at all. It's almost like the USB port doesn't work anymore. I can get into the download mode but then it ends there. I cannot get into the bootloader at all. If I try, it goes to the error screen and if I boot normally, it goes to the error screen.
Brittlespeed said:
Well, I got this same Firmware upgrade error. I can't get the computer to see it at all. It's almost like the USB port doesn't work anymore. I can get into the download mode but then it ends there. I cannot get into the bootloader at all. If I try, it goes to the error screen and if I boot normally, it goes to the error screen.
Click to expand...
Click to collapse
I can't tell if you're asking for help or just letting people know, but anyway, considering all your previous posts were in the Epic 4G Touch forums, you've probably trashed your device flashing something meant for the I9100.
See this thread for confirmation of your new shiny brick, if my above assumption was correct: http://forum.xda-developers.com/showthread.php?t=1492323
this solution worked for a Galaxy s3 mini
fvnktion said:
I had the same problem on my SGS4g after updating to a leaked 2.3.4 rom, which would not make phone calls. Tried to use heidmall to downgrade by loading a new rom. After installing the usb driver as described here http://forum.xda-developers.com/showpost.php?p=14798367&postcount=1 . After reboot I get the error screen <phone..!..Computer> "firmware upgrade encountered an issue. Please select recovery mode in kies and try again". I then took the following steps.
I came across this site: http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Bricked_Screen Under the bricked section it mentions a couple things to try. I the reboot cycle with a couple of times and kept on getting the same screen. Still no go.
I took Odia's advice an did a complete removal of all usb drivers as mentioned and reinstalled kies. This was key in getting odin to recognize the phone again.
My solution:
I try Odin again to try to get it to recognize my phone. I open odin with the usb connected in this state and it is not recognized. I pull battery, it boots to error screen. I restart odin and then plug in the usb and it is recognized. I was then able to load my pit, pda, phone, csc back onto the phone with odin. The first time it tried to load the data it failed, the second time it worked!
Interestingly I never got the "Download Screen". I was still on the mentioned error screen, yet odin was able to still see the phone. The status bar still showed up on the error screen as the fresh rom was being loaded.
I thought I was totally bricked, but this method worked in my case. Hope something similar might work for you.
I still don't know I would get this error screen and have to go through this after loading the required usb driver for heimdall? Any ideas?
Click to expand...
Click to collapse
Thanks a lot. My teenage son thought he had bricked his S3 mini but I was able to fix it after reading this thread. Thanks.

[q] help bricked my galaxy s2

I'm screwed! I was installing
MODEM_I9100XXKE4_REV_02_CL1009835.tar.md5
CODE_I9100XWKE7_CL215725_REV02_user_low.tar.md5
GT-I9100-CSC-XEUKD1.tar
and something happened in Odin3 and it froze, so I took the battery out and tried to restart it and now all I get is a blue and yellow screen that says Android System Recovery. I don't have anything backed up on the device, it didn't come with a microSD card, and it now says
Deleting Cryption Meta Data
-Copying media files....
#manual mode#
updating application....
applying multi-CSC
and that's it. When I hit reboot phone all I get is a screen with a triangle and an android symbol and when I hit apply update from sd card, same symbol, even when I tried to put a .TAR file on my dad's EVO microSD card and put it into the galaxy.
Also, now the USB cable doesn't recognize my phone for some reason so when I go back to ODIN mode it says
Product name - GT-i9100
Custom Binary Download - Yes (1 count)
Current Binary Samsung Official
When I try to restart the phone, it goes straight to the android recovery screen mentioned above, where I can't do anything, and then when I get into the Odin mode, it won't recognize the usb cable so I can link up to Odin3 V1.83 on the computer. Also tried the usb cable on other computers didn't find my phone. Also, as of right now it's not rooted, but I was in the process of rooting, when I realized I missed the Over the Air step so when I Odin3 an insecure.TAR file the WIFI was broke so S2 Root kept saying can't find usb connection even though it was connected, and somewhere along the line when I was trying to restore the radio's by installing the 3 files above, when it crashed something messed up? Now I can't do anything. PLEASE HELP
SO I AM STUCK! Please help????????
Flash the device firmware with Odin when you enter download mode.
Intratech said:
Flash the device firmware with Odin when you enter download mode.
Click to expand...
Click to collapse
Yop
http://www.jayceooi.com/2011/08/14/how-to-restore-stock-firmware-on-samsung-galaxy-s2-video/
I know this topic is old, but I am essentially having the same problem, I don't think it was really solved for the first guy, he can't flash the original rom using odin, because odin doesn't recognize his phone. And that is my issue too, I'm able to get into download mode/odin mode whatever, I plug in the usb cable, nothing, odin doesn't recognize it, I don't get a little sound like I do when I usually plug in a usb cable. Please any ideas would be appreciated.
cowk1ng said:
I know this topic is old, but I am essentially having the same problem, I don't think it was really solved for the first guy, he can't flash the original rom using odin, because odin doesn't recognize his phone. And that is my issue too, I'm able to get into download mode/odin mode whatever, I plug in the usb cable, nothing, odin doesn't recognize it, I don't get a little sound like I do when I usually plug in a usb cable. Please any ideas would be appreciated.
Click to expand...
Click to collapse
Try different versions of Odin (for example, if you're using V4, try V3 1.3 & V3 1.85 and vice versa), try different USB ports (particularly if you're using a port attached to a hub. You need to use a powered port), different USB cables & finally different PC's/different versions of Windoze if you need to.
Also, when you fire up Odin, check Task Manager in Windoze & make absolutely certain Kies or any processes associated with it (if you're not sure what these are, Google/search for them) are not running at the same time. As I've said, you need the drivers that come with Kies to use Odin, but Odin won't work if Kies or anything associated with it is running at the same time.
Try uninstalling Kies on your PC (you need the drivers that come with Kies for Odin to work), rebooting, reinstalling Kies (search for it), rebooting.
If none of that works try cleaning the USB socket of the phone a Q-tip (cotton bud) & some isopropyl alcohol. And if that doesn't work, it might be a case of the USB circuitry of the phone being shot (unless you haven't tried the above steps or are not following the right steps, which we'll never know because we're not there with you).
Was also having the same problem. I managed to get round it by flashing an I9100 package with all the files (PDA, PHONE, BOOT, CSC, PIT) and ticking re-partition. If I'm right, this completely wipes the phone and flashes this over, basically leaving you on a fresh slate.
Hope I helped!
epic118 said:
Was also having the same problem. I managed to get round it by flashing an I9100 package with all the files (PDA, PHONE, BOOT, CSC, PIT) and ticking re-partition. If I'm right, this completely wipes the phone and flashes this over, basically leaving you on a fresh slate.
Hope I helped!
Click to expand...
Click to collapse
Using PIT files is not recommended more brick a phone by flashing PIT than rescue it .
jje
Hi
It seems u tried to flash a sammobile firmware so look to their forum. Why dont u try a phone service?
Sent from my GT-I9100 using XDA

[Q] Verizon Note 2 WILL NOT flash stock in odin. stuck at soft brick

i got the "verizon has detected unauthorized software" soft brick earlier today when trying to partition my sd card. i since have been trying and trying to flash stock in odin to no avail. now, instead of the "detected unauthorized software," i get "firmware upgrade encountered an issue, please select reecovery mode in kies & try again."
kies does nothing. odin fails every time. im getting fed up and i need to leave for work soon
im sorry for the stereotypical help me post but ive looked at MANY threads on here and none helps
If you looked at the stickies you would have had your answer in seconds. Also there are probably a dozen threads about this so you may want to brush up on your searching technique.
Use the alternate restore download.
Here's the thread from the stickies
http://forum.xda-developers.com/showthread.php?p=39299305
Sent from my SGH-T889 using xda app-developers app
souvasaurus said:
i got the "verizon has detected unauthorized software" soft brick earlier today when trying to partition my sd card. i since have been trying and trying to flash stock in odin to no avail. now, instead of the "detected unauthorized software," i get "firmware upgrade encountered an issue, please select reecovery mode in kies & try again."
kies does nothing. odin fails every time. im getting fed up and i need to leave for work soon
im sorry for the stereotypical help me post but ive looked at MANY threads on here and none helps
Click to expand...
Click to collapse
1) Make sure you are using the latest Odin 3.0.7.7(http://www.androidfilehost.com/?fid=23321874045862882) with 4.3 full stock firmware.
2) If not working you could use the full firmware and a PIT file( http://d-h.st/mKu)
or If Odin failed
3) Verizon Utility (Credit to ThePagel):
Download and unzip
SUA_ar.zip http://www.androidfilehost.com/?fid=23269279319199795
Open SUA_ar folder
Install SUABnRSetup as administrator (might take some time and may not be necessary)
Download kies from here http://downloadcenter.samsung.com/content/SW/201312/20131213110414156/KiesSetup.exe and install as administrator. make sure the [Unified Driver Installer] check box is checked at the end of the install (Might take some time)
Make sure Kies is closed then go into download mode and plug into your pc (hold here until drivers install)
Run SUA.exe as administrator
Click on [Repair Assistant] (on the left)
Click on run [Repair Assistant] (on the bottom)
After repair assistant recognizes your phone click [Repair Galaxy Note 2I] (on the right side)
It will say "Due to the condition of your phone/tablet, all data will need to be erased during the repair."
Click [continue]
From here on out its all automated it will download and install full stock firmware then restart (dont forget first boot takes time)
If you get stuck in a boot loop go into recovery and do a factory reset (probably should regardless)
Good luck!
buhohitr said:
1) Make sure you are using the latest Odin 3.0.7.7 with 4.3 full stock firmware.
2) If not working you could use the full firmware and a PIT file
or If Odin failed
3) Verizon Utility (Credit to ThePagel):
Download and unzip
SUA_ar.zip
Open SUA_ar folder
Install SUABnRSetup as administrator (might take some time and may not be necessary)
Download kies from here and install as administrator. make sure the [Unified Driver Installer] check box is checked at the end of the install (Might take some time)
Make sure Kies is closed then go into download mode and plug into your pc (hold here until drivers install)
Run SUA.exe as administrator
Click on [Repair Assistant] (on the left)
Click on run [Repair Assistant] (on the bottom)
After repair assistant recognizes your phone click [Repair Galaxy Note 2I] (on the right side)
It will say "Due to the condition of your phone/tablet, all data will need to be erased during the repair."
Click [continue]
From here on out its all automated it will download and install full stock firmware then restart (dont forget first boot takes time)
If you get stuck in a boot loop go into recovery and do a factory reset (probably should regardless)
Good luck!
Click to expand...
Click to collapse
This always fails at 83% for me. I've tried seven different USB cables including the original Samsung one, and still, no dice. Thanks for the info, though. I was out of options before I saw this.
VDubFanR said:
This always fails at 83% for me. I've tried seven different USB cables including the original Samsung one, and still, no dice. Thanks for the info, though. I was out of options before I saw this.
Click to expand...
Click to collapse
I have the exact problem when trying to repair, it sits at 83% and eventually says phone was disconnected. if I disconnect phone Windows makes the "disconnected device" sound. What is wrong??? Tried flashing stock PIT. No luck. Flashing stock 4.3 via odin fails as well.
I have a different issue where, while in Download Mode, the Verizon Repair Assistant won't let me click the Repair button. It's grayed out.

Categories

Resources