Related
Is there any way to change the apn setting to hspa? I dont want to get throttle using Lte all the time
http://forum.xda-developers.com/showthread.php?t=1506531
hi! newbie here at xda! just want to ask something. i'm concerned about mr zeppelinroxx's 3g build.prop tweak, i'm currently using it right now in experimental 1 settings. is it ok to use this
net.tcp.buffersize.default=6144,87380,110208,6144,16384,110208
net.tcp.buffersize.wifi=262144,524288,1048576,262144,524288,1048576
net.tcp.buffersize.lte=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.hsdpa=6144,262144,1048576,6144,262144,1048576
net.tcp.buffersize.evdo_b=6144,262144,1048576,6144,262144,1048576
net.tcp.buffersize.umts=6144,87380,110208,6144,16384,110208
net.tcp.buffersize.hspa=6144,87380,262144,6144,16384,262144
net.tcp.buffersize.gprs=6144,8760,11680,6144,8760,11680
net.tcp.buffersize.edge=6144,26280,35040,6144,16384,35040
to this?
net.tcp.buffersize.default=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.wifi=262144,524288,1048576,262144,524288,1048576
net.tcp.buffersize.lte=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.hsdpa=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.evdo_b=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.umts=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.hspa=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.gprs=262144,524288,3145728,262144,524288,3145728
net.tcp.buffersize.edge=262144,524288,3145728,262144,524288,3145728
i used the numbers from thr LTE one and replaced the others. i dunno ehat I did, just experimenting though.
i felt a slight improvement i dont know if it is just placebo, is this bad or something?
and sometimes i am getting H+, most of he time H, does that depend on thr carrier? signal? or... i don't know. can someone please help me understand this. i would appreciate it! thanks!
and also i setted my preffered network type to "lte/cdma (prl)"
in the photo attachment you can see that there are 2 results ends in 1.1mbps to 1.3mbps in that case i used the st set of codes, for the speeds 2.05mbps to 2.1mbps i used the 2nd set of codes preffered network type is wcdma only
however when i used the 2nd set of codes and used the prefered network type "lte/cdma (prl) i got the 2.9mbps.
i also attached my phone info if in case that can help thank you!
Well I couldn't wait for AT&T to get the HTC One Max any longer. Especially after Christmas bonuses and such, I had a little extra money, and it was burning a hole in my pocket.
Since one of my Verizon devices was stolen, I've had that account suspended. This was an opportunity to get a new phone and see if Verizon's network is better than AT&T. They seem to go back and forth from time to time in my area of Houston.
Anyways, I popped in my AT&T SIM when the device was starting up for the first time. Had to visit in the in-laws in Louisiana and there was no Verizon service there. It did give me a notice that I was using a foreign SIM card, but it allowed me to proceed. I configured the APN and was on my way with talk, text, and data (HSPA+ up to 14.4Mbps by spec).
As for Cricket, they had a deal on a phone which I could do an unboxing on so I snatched that up. It's an LTE phone and came with a SIM card. In the past I had issues with an "ME rejected" error when trying to put the SIM in a non Cricket phone. Actually with trying to put it on any phone that wasn't on my Cricket account. I still get that error every few minutes with this device BUT talk, text, and data (3G) works. I will contact a dealer and see if I can get the IMEI on the account AND keep the SIM card in the system as well. This might stop the ME rejected issue.
For the time being, Go SMS will have to be used for MMS. I actually don't have the time to do too much more experimentation unless people want me to try out their solution.
Cricket Wireless Setup
AT&T Setup
GO SMS Configurations
Cricket Wireless
http://www.protectionreviews.com/wp-content/uploads/2014/01/CricketUsersHTCOneMaxGoSMS.jpg AT&T
nice!
So no ATT LTE? Shame...
Jiggity Janx said:
So no ATT LTE? Shame...
Click to expand...
Click to collapse
Yeah it doesn't include ATT's LTE bands.
Specs listed below from HTC:
Network1
2G/ 2.5G - GSM/GPRS/EDGE:
850/900/1800/1900 MHz
3G - UMTS/ HSPA:
EMEA: 900/1900/2100 MHz with HSPA+ up to 42 Mbps
Asia: 850/900/1900/2100 MHz with HSPA+ up to 42 Mbps
Sprint: 1900/2100 MHz with HSPA+ up to 14.4 Mbps
Verizon: 850/900/1900/2100 MHz with HSPA+ up to 14.4 Mbps
3G - CDMA
800/1900 MHz for Sprint and Verizon
4G - LTE:
EMEA: 800/900/1800/2600 MHz
Asia: 900/1800/2100/2600 Mhz
Sprint: FDD 800/1900 MHz, TDD 2600 MHz
Verizon: 700/AWS MHz
Wiki Listing of AT&T LTE Networks
AT&T
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
United States700 b17FDDSeptember 2011[128] [depends on CMA-Region]
AT&T
United States700 c17FDDSeptember 2011[128] [depends on CMA-Region]
AT&T
United States700 d29FDD2014 (planned)[129] [EAG-Licenses #701 to 705]
[111] Downlink only.
AT&T
United States700 e29FDD2014 (planned)[129] [5 of 176 EA-Licenses][A 6][105] Downlink only.
AT&T
United States1700 a4FDDSeptember 2011[128] [depends on CMA-Region]
AT&T
United States1700 b4FDDSeptember 2011[128] [depends on EA-Region]
AT&T
United States1700 c4FDDSeptember 2011[128] [depends on EA-Region]
AT&T
United States1700 d4FDDSeptember 2011[128] [REAG-Licenses #5, 7]
AT&T
United States1700 e4FDDSeptember 2011[128] [REAG-Licenses #6, 7]
AT&T
United States19002FDDDecember 2013[130][131] UL/DL Frequencies? Additional network to deliver more bandwidth.
AT&T
United States2300 a b30FDDTBD (planned)[132][133] [473 of 734 CMA-Licenses][C 2][134]Maybe you can get it in some portion of the states.
Specs, Root, Bootloader unlock?
chrisngrod said:
Yeah it doesn't include ATT's LTE bands.
Specs listed below:
Network1
2G/ 2.5G - GSM/GPRS/EDGE:
850/900/1800/1900 MHz
3G - UMTS/ HSPA:
EMEA: 900/1900/2100 MHz with HSPA+ up to 42 Mbps
Asia: 850/900/1900/2100 MHz with HSPA+ up to 42 Mbps
Sprint: 1900/2100 MHz with HSPA+ up to 14.4 Mbps
Verizon: 850/900/1900/2100 MHz with HSPA+ up to 14.4 Mbps
3G - CDMA
800/1900 MHz for Sprint and Verizon
4G - LTE:
EMEA: 800/900/1800/2600 MHz
Asia: 900/1800/2100/2600 Mhz
Sprint: FDD 800/1900 MHz, TDD 2600 MHz
Verizon: 700/AWS MHz
Click to expand...
Click to collapse
Hey, could I get a source for that information? The specs list on HTC site is quite unclear.
Also, is boot loader unlocking possible via HTCDev? Is rooting possible using the international variants method?
Thanks
112358132134 said:
Hey, could I get a source for that information? The specs list on HTC site is quite unclear.
Also, is boot loader unlocking possible via HTCDev? Is rooting possible using the international variants method?
Thanks
Click to expand...
Click to collapse
Source was HTC for the hardware specs.
The listing of AT&T LTE networks is from Wiki.
I'll edit the post because I now see that I was clear as muddy water. Sorry.
IIRC there is a one step root solution if your hboot is a certain version (Verizon). Sprint requires a little more work. It's kind of unrelated to this post. If I get more time, I'll do a video on the root process as well.
EDIT: Jiggity Janx has it in their signature. Rumrunner..
chrisngrod said:
Source was HTC for the hardware specs.
The listing of AT&T LTE networks is from Wiki.
I'll edit the post because I now see that I was clear as muddy water. Sorry.
IIRC there is a one step root solution if your hboot is a certain version (Verizon). Sprint requires a little more work. It's kind of unrelated to this post. If I get more time, I'll do a video on the root process as well.
EDIT: Jiggity Janx has it in their signature. Rumrunner..
Click to expand...
Click to collapse
So, any idea if bootloader unlock is possible, via HTCDev site or otherwise to unlock custom kernels and ROMs?
Thanks for the video.
hello
one sprint htc max can be used with at & t or in my case I live in Honduras can use it with another operator as tigo having the 850 MHz band?
I don't know whether Sprint version is locked or not.
The FCC requires that Verizon leaves their LTE devices unlocked so I'm told in return for being awarded spectrum.
Sent from my HTC6600LVW using Tapatalk
chrisngrod said:
I don't know whether Sprint version is locked or not.
The FCC requires that Verizon leaves their LTE devices unlocked so I'm told in return for being awarded spectrum.
Sent from my HTC6600LVW using Tapatalk
Click to expand...
Click to collapse
then I can buy a htc one max of verizo and use it in my country?
erickmorales2006 said:
then I can buy a htc one max of verizo and use it in my country?
Click to expand...
Click to collapse
Yes. It should based on the specifications listed.
At&t htc one max
They are out [email protected] the AT&T LTE Capable One Max's...bwah hahaha
https://drive.google.com/folderview?id=0Bx5-C2BrwNVxS1RxNzFVUkZpOXc&usp=sharing
Ok where are they I want one.
Sent from my HTC0P3P7 using Tapatalk
charlieb620 said:
Ok where are they I want one.
Sent from my HTC0P3P7 using Tapatalk
Click to expand...
Click to collapse
He bought a replacement board for his one max and ended up with an att board from the vendor.
Hmm.....
Sent from my HTC0P3P7 using Tapatalk
So is there an att one max or not? Lte on the one max would be perfect for me
Sent from my LG-E980 using Tapatalk
Shhh...lmao....id imagine there are others out there,dont think id have the only one....
Jiggity Janx said:
He bought a replacement board for his one max and ended up with an att board from the vendor.
Click to expand...
Click to collapse
I'd leak it to news outlets and eBay the phone for a ridiculous amount of money lol.
Of course I wouldn't buy it because I have both carriers. Someone would though.
Sent from my HTC6600LVW using Tapatalk
Meh I may eventually get rid of it...but for now its a novelty item....Heres another leak....
HTML:
ro.ril.oem.ecclist=911
ro.ril.enable.a52=0
ro.ril.enable.a53=1
ro.ril.enable.dtm=0
ro.ril.gprsclass=10
ro.ril.hsdpa.category=14
ro.ril.hsupa.category=6
ro.ril.hsxpa=4
ro.ril.fast.dormancy.rule=2
ro.ril.att.feature=1
ro.ril.radio.svn=1
ro.ril.disable.fd.plmn.prefix=23402,23410,23411,23420,23594,27202,27205
ro.ril.enable.sdr=0
ro.ril.enable.gea3=1
ro.ril.enable.ucsq=2
ro.ril.set.mtusize=1410
ro.ril.enable.r8fd=0
ro.ril.disable.cpc=1
persist.pdn.profile=nxtgenphone
ro.product.locale.language=en
ro.product.locale.region=US
ro.com.google.clientidbase=android-htc
ro.com.google.clientidbase.yt=android-htc
ro.com.google.clientidbase.am=android-att-us
ro.com.google.clientidbase.gmm=android-htc
ro.com.google.clientidbase.ms=android-att-us
ro.product.model=HTC One max
ro.monkey=0
ro.sllowmock.location=0
ro.config.htc.nocheckin=0
ro.ril.def.agps.mode=1
ro.lpp.profile=3
ro.telephony.ipv6_capability=1
ro.ril.enable.pre_r8fd=1
ro.ril.fd.pre_r8_tout.scr_off=3600
ro.ril.fd.pre_r8_tout.scr_on=0
ro.ril.fd.r8_tout.scr_off=0
ro.ril.fd.r8_tout.scr_on=0
ro.ril.ltefgi=2131623096
ro.ril.ltefgi.rel9=2147483648
CMSUPPORT=0
LTE3GPP=35
ro.ril.enable.isr=1
EnableLTEBANDSCANPRI=1
ro.ril.disable.lte.band2_5=0
dev.defaultwallpaper=/system/customize/resource/wallpapers_a_00.jpg
ro.net.smd=0
ro.htc.preprocess=ATT_EDIAG
# begin build properties
htc.build.stage=1
ro.aa.rid=173
ro.cwkey=CWS__001
ro.aa.skulist=502
ro.aa.customizationid=597951
ro.aa.taskid=340530
ro.onecid=1
ro.aa.project=T6_UL_JB43_SENSE55_ATT
ro.aa.mainsku=502
ro.aa.maincid=CWS__001
ro.prot=false
ro.aa.romver=1.17.502.1
ro.aa.modelid=0P3P50000,0P3P51000,0P3P52000,0P3P60000
ro.aa.report=com
ro.aa.cidlist=CWS__001
# autogenerated by buildinfo.sh
ro.build.id=JSS15J
ro.build.display.id=JSS15J
ro.build.version.incremental=272831.1
ro.build.version.sdk=18
ro.build.version.codename=REL
ro.build.version.release=4.3
ro.build.date=一 11月 11 14:56:23 CST 2013
ro.build.date.utc=1384152983
ro.build.type=user
ro.build.user=
ro.build.host=abm030
ro.build.tags=release-keys
ro.product.brand=htc
ro.product.name=cingular_us
ro.product.device=t6ul
ro.product.board=
ro.product.cpu.abi=armeabi-v7a
ro.product.cpu.abi2=armeabi
ro.product.manufacturer=HTC
ro.product.locale.language=en
ro.product.locale.region=US
ro.wifi.channels=
ro.board.platform=msm8960
# ro.build.product is obsolete; use ro.product.device
ro.build.product=t6ul
ro.build.description=1.17.502.1 CL272831 release-keys
ro.build.description=1.17.502.1 CL272831 release-keys
ro.build.changelist=272831
ro.build.fingerprint=htc/cingular_us/t6ul:4.3/JSS15J/272831.1:user/release-keys
ro.build.characteristics=default
ro.build.project=T6_UL_JB43_SENSE55_ATT:340530
ro.product.version=1.17.502.1
ro.build.languageremove=0
ro.build.sense.version=5.5
# Do not try to parse ro.build.description or .fingerprint
ro.build.description=1.17.502.1 CL272831 release-keys
ro.build.fingerprint=htc/cingular_us/t6ul:4.3/JSS15J/272831.1:user/release-keys
ro.build.characteristics=default
keyguard.no_require_sim=1
# end build properties
#
# system.prop for m7wl
#
rild.libpath=/system/lib/libril-qc-qmi-1.so
rild_dsda.libpath=/system/lib/libril-qc-qmi-qsc.so
rild.libargs=-d /dev/smd0
persist.rild.nitz_plmn=
persist.rild.nitz_long_ons_0=
persist.rild.nitz_long_ons_1=
persist.rild.nitz_long_ons_2=
persist.rild.nitz_long_ons_3=
persist.rild.nitz_short_ons_0=
persist.rild.nitz_short_ons_1=
persist.rild.nitz_short_ons_2=
persist.rild.nitz_short_ons_3=
ril.subscription.types=NV,RUIM
DEVICE_PROVISIONED=1
#
# system.prop for display
#
debug.sf.hw=1
debug.egl.hw=1
debug.composition.type=gpu
debug.enabletr=true
ro.hwui.renderer.disable_opaque=true
ro.sf.lcd_density=480
persist.hwc.mdpcomp.enable=true
debug.mdpcomp.maxlayer=3
debug.egl.buffcount=4
dalvik.vm.heapsize=384m
dalvik.vm.heapgrowthlimit=192m
dalvik.vm.heapstartsize=8m
dalvik.vm.heapmaxfree=8m
dalvik.vm.heapminfree=2m
dev.pm.dyn_samplingrate=1
#
# system props for the cne module
#
persist.cne.UseCne=vendor
persist.cne.UseSwim=false
persist.cne.bat.range.low.med=30
persist.cne.bat.range.med.high=60
persist.cne.loc.policy.op=/system/etc/OperatorPolicy.xml
persist.cne.loc.policy.user=/system/etc/UserPolicy.xml
persist.cne.bwbased.rat.sel=false
persist.cne.snsr.based.rat.mgt=false
persist.cne.bat.based.rat.mgt=false
persist.cne.rat.acq.time.out=30000
persist.cne.rat.acq.retry.tout=0
persist.cne.sync.swim.mode=false
ro.hdmi.enable=true
lpa.decode=true
tunnel.decode=true
lpa.use-stagefright=true
lpa.releaselock=true
#system props for the MM modules
media.stagefright.enable-player=true
media.stagefright.enable-http=true
media.stagefright.enable-aac=true
media.stagefright.enable-qcp=true
media.stagefright.enable-fma2dp=true
media.stagefright.enable-scan=true
mmp.enable.3g2=true
#
# system props for the data modules
#
ro.use_data_netmgrd=true
#system props for time-services
persist.timed.enable=true
# System props for audio
persist.audio.fluence.mode=endfire
persist.audio.vr.enable=false
persist.audio.handset.mic=digital
# System props for soundhound
persist.htc.audio.pcm.samplerate=48000
persist.htc.audio.pcm.channels=2
# System prop to select audio resampler quality
af.resampler.quality=255
# System props for global effect
htc.audio.global.state=0
htc.audio.global.profile=0
htc.audio.q6.topology=0
htc.audio.global.speaker=1
# System props for inbox bundle headset info
persist.htc.audio.inbox.profile=max300_2vol_20130219
#
# system prop for opengles version
#
# 196608 is decimal for 0x30000 to report version 3
ro.opengles.version=196608
#system prop for switching gps driver to qmi
persist.gps.qmienabled=true
# System property for cabl
ro.qualcomm.cabl=0
#
# System prop for sending transmit power request to RIL during WiFi hotspot on/off
#
ro.ril.transmitpower=true
# Enable IMS service by default
persist.radio.jbims=1
# For workaround for ro.baseband property. QCT use the property same as radio version to determine the architecture.
# But we hard code to dsda for M7 DxG.
ro.baseband.arch = mdm
#Add default network type for phone reference
ro.telephony.default_network=9
#Support manual selection with rat by qualcomm interface.
ro.ril.scan.selection.rat = 1
#
#Simulate sdcard on /data/media
#
persist.fuse_sdcard=true
# ro.storage_structure: define the storage structure of this project
# FUSE: 0x8, FAT: 0x4, SD: 0x2, INS: 0x1
# Example: If the project has FUSE with SD card, the value should be defined as 10 (dec)
ro.storage_structure = 10
# M7 Hardware Info
ro.product.bluetooth=4.0
ro.product.display_resolution = 5.9 inch 1080p resolution
ro.product.main_camera = HTC UltraPixel Camera
ro.product.front_camera = 2.1M
ro.product.processor = Quadcore
ro.product.ram = 2GB
ro.product.wifi = 802.11 a/b/g/n/ac
#SSD_BT+ bluetooth
#
# system prop for bluetooth logcat/snoop enable
#
#bluetooth.hcidump.enabled=1
#
# system prop for Bluetooth Dialup Networking
#
ro.qualcomm.bluetooth.dun=false
# system prop for Bluetooth FTP profile
ro.qualcomm.bluetooth.ftp=true
#
# system property for Bluetooth Handsfree Profile Wide Band Speech
#
ro.qualcomm.bluetooth.hfp.wbs=false
#
#system prop for Bluetooth hci transport
ro.qualcomm.bt.hci_transport=smd
#
# system prop for requesting Master role in incoming Bluetooth connection.
#
ro.bluetooth.request.master=true
#
# system prop for Bluetooth Auto connect for remote initated connections
#
ro.bluetooth.remote.autoconnect=true
# system property for Bluetooth discoverability time out in seconds
# 0: Always discoverable
#debug.bt.discoverable_time=0
# system property for Bluetooth Hardware information
ro.product.bluetooth=4.0
# config fm rssi threshold
service.qct.fm.rssi=116
#SSD_BT- bluetooth
# BLE TAG (HtcBluetoothLeProfiles)
ro.bt.ble_tag = 1
# wifi
wifi.softap.interface=wlan0
wifi.softapconcurrent.interface=softap.0
wifi.miracastconcurrent.scan=WCN3680
init.svc.wpa_supplicant=
init.svc.dhcpcd_wlan0=
dhcp.wlan0.autoip=
dhcp.wlan0.dns1=
dhcp.wlan0.dns2=
dhcp.wlan0.dns3=
dhcp.wlan0.dns4=
dhcp.wlan0.gateway=
dhcp.wlan0.ipaddress=
dhcp.wlan0.leasetime=
dhcp.wlan0.mask=
dhcp.wlan0.ooxx=
dhcp.wlan0.pid=
dhcp.wlan0.reason=
dhcp.wlan0.result=
dhcp.wlan0.server=
net.wlan0.dns1=
net.wlan0.dns2=
wifi.wpa_supp_ready=
wlan.driver.status=
wifi.interface=wlan0
wifi.supplicant_scan_interval=15
persist.wifi.v6=true
persist.wifi.v6.rs.count=5
persist.wifi.v6.rs.timeout=5
# Support HW reset
ro.product.hwreset = 1
# For EXT4 file system
ro.ext4fs = 1
# support 3LM encryption
ro.3LM_SD_ENCRYPT = fasle
# ro.storage_encryption_type: define the storage encryption type of this project
# not support encryption: 0x0 block level: 0x1 file level: 0x2
ro.storage_encryption_type = 2
#For usb storage
ro.usb_host = 1
# Preloading common control assets
persist.preload.common=1
# Perflock for inter-process activity launch and first launch
persist.htc.multicore.timeout = 1500
# Perflock for Home process lock duration
persist.htc.multicore.home = 800
# Property for MPEG2TS playback
TSParser.disable.seek = 1
# T6 SGLTE set default network type GSM/WCDMA/LTE auto
persist.radio.prefer.network = 9
# For Embadded DIAG
ro.chipset.vendor=QCT
ro.chipset.model=APQ8064
ro.chipset.version=2.0
#
# ADDITIONAL_BUILD_PROPERTIES
#
debug.nfc.fw_download=true
debug.nfc.fw_boot_download=false
ro.carrier=unknown
ro.config.notification_sound=OnTheHunt.ogg
ro.config.alarm_alert=Alarm_Classic.ogg
drm.service.enabled=true
ro.setupwizard.mode=OPTIONAL
ro.com.google.gmsversion=4.3_r1
ro.vendor.extension_library=/system/lib/libqc-opt.so
persist.preload.common=1
persist.camera.antibanding=60
persist.camera.tuning_spec=htc
net.bt.name=Android
dalvik.vm.stack-trace-file=/data/anr/traces.txt
chrisngrod said:
I'd leak it to news outlets and eBay the phone for a ridiculous amount of money lol.
Of course I wouldn't buy it because I have both carriers. Someone would though.
Sent from my HTC6600LVW using Tapatalk
Click to expand...
Click to collapse
Just curious, how much did the board cost? It'd be a roll of the dice to get another.
Sent from my HTC6600LVW using Tapatalk
Hi.
As far as I know from digging in the specs from different sources - one max from Verizon is capable of AWS LTE band 4.
The problem is that it never gets connected to LTE on T-Mo.
I have forced it from info menu to LTE only, but it stays disconnected.
Can anybody shed light on what may be preventing the Tmo AWS LTE to work on a AWS compatible one max.
May it be in need of software update?
Need to put in TMo APN info maybe...
Jiggity Janx said:
Need to put in TMo APN info maybe...
Click to expand...
Click to collapse
Tried
*I believe* the aws has to be enabled through a software update like the gs4 was when aws was enabled for verizon. Otherwise I would be getting verizon aws speeds in my area with my verizon one max right now.
Jiggity Janx said:
*I believe* the aws has to be enabled through a software update like the gs4 was when aws was enabled for verizon. Otherwise I would be getting verizon aws speeds in my area with my verizon one max right now.
Click to expand...
Click to collapse
That actually makes sense.
Thank you for your input.
Actually it's in a hidden. menu
Antigen said:
That actually makes sense.
Thank you for your input.
Click to expand...
Click to collapse
I'm currently using a note 3 Verizon on tmo lte. And band 4 had to be enabled in a hidden menu. If someone had the dial codes to the band selection on the HTC one max that would fix it.
saw the note 3 how to on tk tech news on youtube.
TechSoft said:
I'm currently using a note 3 Verizon on tmo lte. And band 4 had to be enabled in a hidden menu. If someone had the dial codes to the band selection on the HTC one max that would fix it.
saw the note 3 how to on tk tech news on youtube.
Click to expand...
Click to collapse
When I looked into this because I am in a verizon aws area it was not possible because we have the same setup as the verizon one (not the verizon s4 which I also have or n3). The One does not have the software part required for aws to work and neither would we.
note 3, blackberry z30, lg g2, htc one max all on TMOBILE LTE!
Jiggity Janx said:
When I looked into this because I am in a verizon aws area it was not possible because we have the same setup as the verizon one (not the verizon s4 which I also have or n3). The One does not have the software part required for aws to work and neither would we.
Click to expand...
Click to collapse
I just followed the procedure on a video at TK Tech News on YouTube. it shows the LG G2 working on TMOBILE LTE and they also stated putting a aosp rom on the HTC one max enables TMOBILE LTE or allows you to force cat 4 lte.
I'm in the process of rooting and s off this one to see if it works. it has and I've confirmed it working on the g2 and the note 3 as well as the blackberry z30.
thanks
TechSoft said:
I just followed the procedure on a video at TK Tech News on YouTube. it shows the LG G2 working on TMOBILE LTE and they also stated putting a aosp rom on the HTC one max enables TMOBILE LTE or allows you to force cat 4 lte.
I'm in the process of rooting and s off this one to see if it works. it has and I've confirmed it working on the g2 and the note 3 as well as the blackberry z30.
thanks
Click to expand...
Click to collapse
There is no aosp rom for the Max with working radio. No kernel source. So they can say putting a aosp rom on there does it all they want but no one can do it currently.
Working!!!
That guy is full of it. But after some trial and error I got it working and have full 4G speed.
In build.prop change or add these if they dont exist
ro.ril.gprsclass=14
ro.ril.hsdpa.category=14
ro.ril.hsupa.category=7
ro.ril.hsxpa=2
ro.telephony.lteOnGSMDevice=1
ro.telephony.default_network=9
Also open the /system/customize/ACC/default.xml file, is a boolean variable “sku_id”. Change the value of “sku_id” to the t-mobile one. Then save the file, and reboot your device.
<item type="integer" name="sku_id">11</item>
Then go into the *#*#4636#*#* menu with the phone dialer (it will be enabled now) and change the network type to "GSM/WCDMA/LTE auto"
barrygeorge001001 said:
That guy is full of it. But after some trial and error I got it working and have full 4G speed.
In build.prop change or add these if they dont exist
ro.ril.gprsclass=14
ro.ril.hsdpa.category=14
ro.ril.hsupa.category=7
ro.ril.hsxpa=2
ro.telephony.lteOnGSMDevice=1
ro.telephony.default_network=9
Also open the /system/customize/ACC/default.xml file, is a boolean variable “sku_id”. Change the value of “sku_id” to the t-mobile one. Then save the file, and reboot your device.
<item type="integer" name="sku_id">11</item>
Then go into the *#*#4636#*#* menu with the phone dialer (it will be enabled now) and change the network type to "GSM/WCDMA/LTE auto"
Click to expand...
Click to collapse
Did This work? If So I need somehelp on where i need to do to enter the codes. Do i need to me rooted?
You need root to edit those files.
barrygeorge001001 said:
That guy is full of it. But after some trial and error I got it working and have full 4G speed.
In build.prop change or add these if they dont exist
ro.ril.gprsclass=14
ro.ril.hsdpa.category=14
ro.ril.hsupa.category=7
ro.ril.hsxpa=2
ro.telephony.lteOnGSMDevice=1
ro.telephony.default_network=9
Also open the /system/customize/ACC/default.xml file, is a boolean variable “sku_id”. Change the value of “sku_id” to the t-mobile one. Then save the file, and reboot your device.
<item type="integer" name="sku_id">11</item>
Then go into the *#*#4636#*#* menu with the phone dialer (it will be enabled now) and change the network type to "GSM/WCDMA/LTE auto"
Click to expand...
Click to collapse
Can anyone please tell me what I need to do to get to build.prop to change or add this information. I am currently rooted with s off and supercid, using NuSenseSIX Rom.
**Edit**
Nervermind I figured it out. There's a app called "buildprop editor" that takes you where to go and let's you add or change what you need to. Also you definetly need to change the sku id to 11 or it will not work. If you have problems saving the change to the sku id, install fx file explorer and fx file explorer (root ad-on) from the google play store. The apps were created by NextApp Inc. The FX file explorer has a lock icon that you click on in the upper right corner that will give r/w capabilities necessary to save any changes.
This may help further.....
barrygeorge001001 said:
That guy is full of it. But after some trial and error I got it working and have full 4G speed.
In build.prop change or add these if they dont exist
ro.ril.gprsclass=14
ro.ril.hsdpa.category=14
ro.ril.hsupa.category=7
ro.ril.hsxpa=2
ro.telephony.lteOnGSMDevice=1
ro.telephony.default_network=9
Also open the /system/customize/ACC/default.xml file, is a boolean variable “sku_id”. Change the value of “sku_id” to the t-mobile one. Then save the file, and reboot your device.
<item type="integer" name="sku_id">11</item>
Then go into the *#*#4636#*#* menu with the phone dialer (it will be enabled now) and change the network type to "GSM/WCDMA/LTE auto"
Click to expand...
Click to collapse
I found out something tricky with this phone, "ro.ril.gprsclass=14" was causing my phone to hang on boot so I kept resetting it with the hardware keys so after I got it booted up, I proceeded to delete the ro.ril.gprsclass=14 in buildprop or sometimes the phone would delete it first and second I spotted a key that looked similar to "ro.telephony.lteOnGSMDevice=1" in buildprop which was "telephony.lteOnCdmaDevice=1". Noticed the CDMA wasn't all Caps????. So I modified the Key in buildprop to look like this "ro.telephony.lteOnGsmDevice=1", only the "G" is capped in GSM......And After I did that I restarted the phone and after it booted, I proceeded to phone test menu and changed it to "GSM/WCDMA/LTE auto" and boom I've noticed the "4GLTE" showed up in my status bar so I did a speed test and surely I was getting 30 Mbps Down and 10 Mbps Up. One other good thing is my MMS IS WORKING!!!!!!! just ass fast as an SMS!!!!!
The Rom I'm Using Is: NuSenseSIX-LP_t6_RC5.0.4.2_11132015
UPDATE: Everytime you restart your device, the test menu reverts back to "GSM prl" so just put it back on "GSM/WCDMA/LTE auto" and your LTE will return.
Will this work with sprint variant
Sent from my HTC0P3P7 using XDA Free mobile app
From my research, it seems many folks are having problems with IPv6 on their Android devices, and one poster found this:
https://goo.gl/A7LfIW "the explanation is in comment #23: "what changed is that Android now supports RDNSS. The device is getting (and using) an IPv6 DNS server via RDNSS without an IPv6 address that it can use to talk to it, and that delays DNS queries".
So, I've been using an app from the Play Store that disables IPv6, but it needs to be run/applied way too frequently.
Does anyone know of an app that will script the change to disable IPv6, but preferably also script/unscript the changes when or if needed?
I was able to find and follow these instructions to have it done automatically, but it still has to run every time wlan0 varies on/off, which is a lot of times, considering the phone disables WiFi to send MMS!
https://www.reddit.com/r/Android/comments/2z1gyo/fix_lollipop_wifi_issues_and_coincidentally_the/
I'm using a:
T-Mobile Galaxy S6 [SM-G920T]
Android 5.0.2
Disable IPV6 on vs985 Rooted, running CRDROID 7.1.2
After reading all the issues with IPV6 and the difficulty in turning it off... I came across a way to disable it permanently. Reversible of course....
I modified my apn config file in SYSTEM/ETC/APNS-CONF.XML
This is what it looks like now:
<apns version="8">
<apn carrier="Test Internet" mcc="001" mnc="01" apn="VZWINTERNET" type="default,dun,mms,supl" protocol="IPV4" roaming_protocol="IPV4" />
Where "IPV4V6" was, it was changed to "IPV4"
Find the apn=(whatever apn you have selected on your phone).... in my case it was VZWINTERNET, and edit the two IPV4V6 entries after that.
Using Network Info ll, it now shows "No IPV6 gateway found".
Maybe other systems will have an apns config file of some kind.