Im running aosp 2.3.4 on my optimus v, whenever I try to connect to my computer my phone reboots to the "android" logo, NOT a full reboot, just to the android logo. Whats wrong with it? I really need to do it this way, i know you can transfer over wifi and dropbox but i'd rather do it via usb. It detects the phone, it finds all the hardware, but once i click turn on usb mass storage on the phone, it waits a few seconds then reboots.
qccoles said:
Im running aosp 2.3.4 on my optimus v, whenever I try to connect to my computer my phone reboots to the "android" logo, NOT a full reboot, just to the android logo. Whats wrong with it? I really need to do it this way, i know you can transfer over wifi and dropbox but i'd rather do it via usb.
Click to expand...
Click to collapse
Try another cable? Another USB port? Another ROM? (Another phone? )
it's not the cord or the usb.
qccoles said:
it's not the cord or the usb.
Click to expand...
Click to collapse
Well, then go and try the ROM. (Or different kernel first, maybe.)
apparently everythings fine on my computers end...ugh i dont want to do a fresh install on my phone.
I found a workaround. Reboot into recovery and toggle mass storage from there...eh.
qccoles said:
I found a workaround. Reboot into recovery and toggle mass storage from there...eh.
Click to expand...
Click to collapse
Tried it but phone still reboots when i click on "USB connected" , still keeps on rebooting....
What exactly are you doing? You reboot into recovery and select toggle USB MS
earthworm1102 said:
Tried it but phone still reboots when i click on "USB connected" , still keeps on rebooting....
Click to expand...
Click to collapse
1/ He said in recovery. You do not get any "USB connected" screen in recovery.
2/ Tried different kernel yet?
Complaining "I still have the issue" without trying the suggestions (properly) will not exactly get you anywhere.
there is something wrong wth the flashing do a clean install and make sure u have drivers installed.
qccoles said:
Im running aosp 2.3.4 on my optimus v, whenever I try to connect to my computer my phone reboots to the "android" logo, NOT a full reboot, just to the android logo. Whats wrong with it? I really need to do it this way, i know you can transfer over wifi and dropbox but i'd rather do it via usb. It detects the phone, it finds all the hardware, but once i click turn on usb mass storage on the phone, it waits a few seconds then reboots.
Click to expand...
Click to collapse
you must not have partitioned the sd card...so the card unmounts when u connect to pc in mass storage mode...since apps are stored on the card..the phone reboots...other than games..put apps on the phone..then connect...problem will be gone..i ave had the same problem...after lot of research n careful observation...i solved it finally...cheers...
qccoles said:
I found a workaround. Reboot into recovery and toggle mass storage from there...eh.
Click to expand...
Click to collapse
This worked for me.
akki1791 said:
you must not have partitioned the sd card...so the card unmounts when u connect to pc in mass storage mode...since apps are stored on the card..the phone reboots...other than games..put apps on the phone..then connect...problem will be gone..i ave had the same problem...after lot of research n careful observation...i solved it finally...cheers...
Click to expand...
Click to collapse
I don't have my card partitioned so that must be the cause. I guess I am too lazy to move everything and I will continue to use the recovery to access.
Related
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
fizzle101 said:
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
Click to expand...
Click to collapse
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Can you try booting in fastboot and tell me if that is recognized?
it still doesnt recognize it in fastboot
fc_Kuro said:
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Click to expand...
Click to collapse
i have tried that and it doesnt help
fizzle101 said:
i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message
Click to expand...
Click to collapse
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
ok i will give that a try
crk23 said:
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
Click to expand...
Click to collapse
that didnt work. o well i guess i am stock with the rom i have there.
fizzle101 said:
that didnt work. o well i guess i am stock with the rom i have there.
Click to expand...
Click to collapse
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
robocik said:
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
Click to expand...
Click to collapse
i have tried everything. changed the cable, used different pc but nothing works. i think is a hardware problem, something might be broken inside or something like that
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
baklap said:
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
Click to expand...
Click to collapse
No i havent and i gave up trying because i dnt think there is a fix for it. if yours is unrooted and the warranty is still valid you should consider returning it to HTC maybe they might replace it
got the same problem. Any solution so far ??
ddotpatel said:
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
Click to expand...
Click to collapse
Did you try that?..... You need to do the reboot PC/Laptop after uninstalling ALL HTC drivers! Then when you reboot PC, plug phone back in, should say "not recognised" again,... then follow BTDAG's guide. T'is definitely a driver issue!
tried flashing 3 roms, modaco, radug and now kimera... none working.
can connect in fastboot, it shows up in device manager as android 1.0
ive tried 3 different usb cables and 4 differet pcs, still there is no response on my phone !!!
using villian rom 10.0 rite now.
okay it boots up into fastboot and fastboot usb shows up on the screen in red,
BUT when i use the "adb devices" command in adb it doesnt show the device,
it is showing as android 1.0 in devices and printers (windows 7)
You need to use....
fastboot devices
....when your are in fastboot.
What happens when you go into your recovery, select "Toggle MS/USB" with USB connected to PC?
okay
fastboot devices command shows some serial number.
then i tried adb remount, it gave an error....
enabling usb-ms with cable attached gives no response
ok i think it might be USB driver like ddotpatel said but i am not sure.
i reinstalled my whole windows 7 to 32bit now instead of the 64bit version i was using before and today i just connected my hero to my PC and windows 7 did its thing and installed the drivers and finally my hero can mount the SD card in my PC again although i kept getting this can perform faster in USB 2.0 port or something like that i didn’t care as long as i can mount my SD card again.
now went into fastboot and used the fastboot device command and i could see my hero serial no. but when i try to flash the amonra recovery i got the permission error (i cant really remember). i tried flashing using the adb method but still no luck.
so i went to market and downloaded rom manager and used it to flash clockwork recovery and now i could boot to clockwork recovery.
from this recovery i can now flash any rom i want and although there are still a few more problems i am glad now that i can flash custom roms again.
the problem i can see so far but i can deal with is
1. i don’t think fastboot commands work even if the phone is detected.
2. SD card mounts at USB 1.1 speed. (i have tried different ports and cable but still the same thing and this is the ports i use for my N1, Desire and my other android phones with USB 2.0 speed)
PS: adb commands for pushing and removing apps is working.
Hope this can be helpful to those experiencing the same problem.
Instead of re-installing your entire OS just use usbdeview to remove the failing drivers.
Also remove any old HTC Sync installs and install the latest version.
Hey guys, I'm trying to update the VOID rom from Delta to Charlie and I'm using my PC now. I'm trying to toggle it to USB mode but it's not recognized on my PC. I usually do it at my friend's place and it recognizes it perfectly but on my PC it doesn't.
When I plug it in, it says "LG Android USB Device - Not recognized" or "No Driver Found"
How do I go about fixing this? I've already wiped the data and everything, just need to put the zip file in.
Been trying to get a hold of my friend but he's got class until tonight, and I kinda wanna not be depending on him if I need to do stuff with my phone, so I might as well try to get the drivers on my PC.
Any help would be great
Ok, so I just found the most random fix.
I took out the SD card, kept the cover off, booted into recovery, put the SDcard back in and mounted it, toggle USB and it worked.
So random but it worked!
Magnetix said:
Hey guys, I'm trying to update the VOID rom from Delta to Charlie and I'm using my PC now. I'm trying to toggle it to USB mode but it's not recognized on my PC. I usually do it at my friend's place and it recognizes it perfectly but on my PC it doesn't.
When I plug it in, it says "LG Android USB Device - Not recognized" or "No Driver Found"
How do I go about fixing this? I've already wiped the data and everything, just need to put the zip file in.
Been trying to get a hold of my friend but he's got class until tonight, and I kinda wanna not be depending on him if I need to do stuff with my phone, so I might as well try to get the drivers on my PC.
Any help would be great
Click to expand...
Click to collapse
I had the same problem, and the fix was to install the LG USB driver from the microSD card included with the phone.
Hello people, I have the same problem.
It works well but when I go into recovery and I toggle USB nothing happens.
Where can I find the drivers?
Which driver do I have to uninstall?
paolog89 said:
Hello people, I have the same problem.
It works well but when I go into recovery and I toggle USB nothing happens.
Where can I find the drivers?
Which driver do I have to uninstall?
Click to expand...
Click to collapse
http://www.lg.com/sg/support/produc...rgetPage=support-product-profile-mobile-redux
Download the LG Mobile Support tool first ... from there you can download the LG USB Drivers ... Once they are installed, your SD card will be detected in recovery ..
Nothing to uninstall ... PM if you need help
Could also just put the microSD in a card reader and put the ZIP on that way
hey guys, hopefully i can get some help with this...
flashed my Galaxy s2 to 4.0.3 (I9100 XXLPQ) then rooted it using chainfire kernel (followed instrcutions to the tee) everything worked great.. then ran triangleaway app, everythign still fine so far (weo)
a day later i connected my phone to pc to transfer some stuff but it doesnt show up at all anymore. tried connecting on 3x computers w/ different cables. opened device manager, that doesnt pick it up either. kies troubleshoot froze. i decided to do a factory reset (erasing internal sd as well), i had nothing important on the phone anyway. this didnt work. when i try and enable usb storage mode it says i should unplug the cable.so when i unplugand select the mode, it tells me i should connect the cable to use mass storage mode. i plug it in while thats up to see if anything happens...nothing
also there seems to be a huge amount of battery draining going on. this morning i turned on my phone just to complete the charge. i left it for 20min before i left but it was still charging. thought whatever just took it, got to work the thing is like 5% done already
any help would be appreciated thanks!
pulse1989 said:
it says i should unplug the cable.so when i unplugand select the mode, it tells me i should connect the cable to use mass storage mode. i plug it in while thats up to see if anything happens...nothing
Click to expand...
Click to collapse
That's because you have to click under the orange droid to put the phone into mass storage mode. You selected a different USB mode but you have to enable it in order to use it.
bpivk said:
That's because you have to click under the orange droid to put the phone into mass storage mode. You selected a different USB mode but you have to enable it in order to use it.
Click to expand...
Click to collapse
How? because i usually do it via menu -> settings-> USB utilities USB mass storage , "connect storage to pc"
Yes, even me now I can't connect to USB not even to the Download mode!
I have no way to even root my phone!!
It's not me, it's more like a general problem floating around!
How about your device-usb driver? they are updated or installed?
Hi all,
I have a Rooted, WanamLite v6.3 ZSEMC1 ROM with AdamKernel 2.2.1+. i9300.
I updated recently from another previous version of the same ROM because I had noticed that my USB functionality has not been working. Specifically, the MTP application. Soon further found that my computer does not recognise ADB commands at all, as I used to install .apks from my computer quickly with adb install.
Odin does not even recognise my phone, even when in download mode. The only thing I havent tried yet is ADB in CWM Recovery, but im 99% sure that wont work still.
When I plug the micro-usb plug in it charges fine, but no data connection seems to occur. No windows detection, No USB device connected in the notifications bar.
I have tried:
-Backing up
-Installing vanilla ROM
-Installing stock ROM
-Using different computer with drivers
-Reinstalling Samsung Drivers
-Tried using Kies for the drivers
-Changing SD cards
-Power Cycling phone removing sim and micro-sd cards. Turning on after some time.
-Cleaning the micro-usb port on the phone with dental picks.
Im pretty much out of ideas apart from trying to organise to send it for repairs, after un-rooting.
If I was to re-root do you think this would solve the problem?
Any help is much appreciated.
Thanks :good:
UPDATE: I fixed this by using Mr. Despairs suggestion.
Power off, pull battery, SIM, SD card. Power cycled the power button with no battery in it.
Waited about 1-2 minutes.
Battery in boot straight to Download Mode.
Only got it to recognise once in about 15 tries.
Thanks again Mr Despair!
You could also try another cable. Or what I read in another german forum: Shut down your phone, take the battery out and in and reboot. Then reboot into download mode and plug in your phone. Then your PC should search for drivers.
Do this as a colleague says Mr. Despair replace the cable. Often dirt in the connector. Clean the connector on the phone.
Also check ...
Also check on a different computer/port - it could be a problem with the USB drivers on your computer.
Probably the safest test would be to cross-test combinations of 2-3 computers vs 2-3 phones.
xclub_101 said:
Also check on a different computer/port - it could be a problem with the USB drivers on your computer.
Probably the safest test would be to cross-test combinations of 2-3 computers vs 2-3 phones.
Click to expand...
Click to collapse
He already wrote that he tried more PCs. He would have very bad luck if it is on both. But trying doesn't cost. He shoule then also try to plug it direct into the USB ports and not through a hub.
I have also tried two other cables which both previously worked.
Ill give the hard reboot into download mode a try.
No PC recognises it at all at the moment.
I have tried all USB ports, directly not through a hub or whatnot. This includes other computers too.
Im open to any other suggestions.
Thanks for the help so far
Have you installed KIES?
KIES and ODIN cannot co-exist.
Install ONLY Samsung USB drivers then run ODIN.
As for installing apks, you shouldn't need to install via adb. You can just copy to sdcard and run from there.
Sent from my GT-I9300 using XDA Premium
IRPnet said:
Have you installed KIES?
KIES and ODIN cannot co-exist.
Install ONLY Samsung USB drivers then run ODIN.
As for installing apks, you shouldn't need to install via adb. You can just copy to sdcard and run from there.
Sent from my GT-I9300 using XDA Premium
Click to expand...
Click to collapse
I had used ODIN without KIES existing on my system.
I installed KIES to try and get it to read my phone for once.
I used ADB to install .apks when I had ADB running. I have the problem now that I cant use it, because my phone MTP, ADB or even Download Mode wont read my phone. All from different computers etc.
:crying:
Sounds more and more like a hardware failure. What about reboot to CWM then in mounts and storage to mount the USB drive? Can your PC recognize it this way?
Mr. Despair said:
Sounds more and more like a hardware failure. What about reboot to CWM then in mounts and storage to mount the USB drive? Can your PC recognize it this way?
Click to expand...
Click to collapse
Yeah im thinking hardware too. If I throw it into CWM and try to mount /sdcard, it doesnt to anything. Nothing changes it just stays permanently on mount /sdcard. (Its not mounting).
Mounting external_sd works but its not helping me.
Anyone ever returned a SGS3 to factory or phone provider?
Mr. Despair said:
You could also try another cable. Or what I read in another german forum: Shut down your phone, take the battery out and in and reboot. Then reboot into download mode and plug in your phone. Then your PC should search for drivers.
Click to expand...
Click to collapse
I initially tried this with no success, however after about 15 tries I got it to work once!
Thanks heaps for this!
Pull Battery, SIM and SD. Press Power buttons a few times and let it sit for about 1 minute.
Battery in and boot straight to Download mode. Worked once in about 15 tries. Reflashed everything and it works now!
Thanks Despair!!:laugh::laugh::laugh::laugh::laugh::laugh::laugh::laugh:
Hi all,
by cons for several weeks I've a concern with my redmi Note 2 and I can't find the answer to my problem on the forum or even the Internet.
Since the last update 7.2.2 (global) I have the Recovery MIUI who crushed the TWRP. I changed to test 6.3.17. The update to the .24 went wrong and I don't know why. Since the phone is bootloop. But the problem is that my phone is not recognized by any PC. I tried several PCs, several cables, several drivers, with or without the Fastboot, unable to connect. Therefore impossible to load a new version. I don't think it's material problem because the phone recharge well with a cable to the socket.
Is there another handling or debug decision to restart the phone? I'm in France for information.
thank you in advance if you can point me to a solution !
Hope someone can help me.
Manu
Can the phone boot to miui recovery? If so, you should be able to use miui recovery to flash TWRP (I think you will need one with a signed install zip). You only need to take out the external SD, put it in one of those cheap USB card readers, copy your recovery and ROM to the SD, put it back in the phone, flash TWRP with miui recovery, and then flash the ROM with TWRP (I am assuming that miui recovery can install things from the external SD - if not, then none of this will work).
Hi Bro,
Yes it boot in MIUI recovery but impossible to get access to the SD Card...
I tried to put the file on the SD card but you can't choose the path, I think the recovery will look only in the internal memory ... And as I can't access the internal memory..
I despair !!
Thanks o lot for your help
DarthJabba9 said:
Can the phone boot to miui recovery? If so, you should be able to use miui recovery to flash TWRP (I think you will need one with a signed install zip). You only need to take out the external SD, put it in one of those cheap USB card readers, copy your recovery and ROM to the SD, put it back in the phone, flash TWRP with miui recovery, and then flash the ROM with TWRP (I am assuming that miui recovery can install things from the external SD - if not, then none of this will work).
Click to expand...
Click to collapse
manu33xtro said:
Hi Bro,
Yes it boot in MIUI recovery but impossible to get access to the SD Card...
I tried to put the file on the SD card but you can't choose the path, I think the recovery will look only in the internal memory ... And as I can't access the internal memory..
I despair !!
Thanks o lot for your help
Click to expand...
Click to collapse
Ok - but have you tried the Mediatek SP Flash Tool?
Of course yes but the real problem is that the phone is not recognized by the PC and therefore can't load anything ...
Even changing drivers or cables or PC, nothing to do.
DarthJabba9 said:
Ok - but have you tried the Mediatek SP Flash Tool?
Click to expand...
Click to collapse
manu33xtro said:
Of course yes but the real problem is that the phone is not recognized by the PC and therefore can't load anything ...
Even changing drivers or cables or PC, nothing to do.
Click to expand...
Click to collapse
So, when the battery is removed, and you connect the USB cable, the phone is not even vibrating (and making that weird sound) every couple of seconds or so?
Yes you're right : every 10s the phone vibrate...
DarthJabba9 said:
So, when the battery is removed, and you connect the USB cable, the phone is not even vibrating (and making that weird sound) every couple of seconds or so?
Click to expand...
Click to collapse
manu33xtro said:
Yes you're right : every 10s the phone vibrate...
Click to expand...
Click to collapse
Well, then it is very strange that you can't use the SP Flash Tool. If the phone vibrates, then the device is recognised, and you should be able to flash anything you want with the SP Flash Tool! How exactly were you trying to use the Flash Tool?
I tried so many solutions I really don't know exactly how I used the software.
I will again try everything.
But against any changes when I look in the USB settings of the PC, the phone doesn't appear.
I try again just now, thank you for your help.
DarthJabba9 said:
Well, then it is very strange that you can't use the SP Flash Tool. If the phone vibrates, then the device is recognised, and you should be able to flash anything you want with the SP Flash Tool! How exactly were you trying to use the Flash Tool?
Click to expand...
Click to collapse
manu33xtro said:
I tried so many solutions I really don't know exactly how I used the software.
I will again try everything.
But against any changes when I look in the USB settings of the PC, the phone doesn't appear.
I try again just now, thank you for your help.
Click to expand...
Click to collapse
With the SP Flash Tool, all you need is the correct "scatter" file (MT6795_Android_scatter.txt), and the image(s) that you want to flash. If the phone is vibrating, then the SP Flash Tool should be able to connect to it when you click "Download". Just make sure that you first untick everything that you do NOT want to flash. I would try flashing the boot image (boot.img) first. If that succeeds, then try the TWRP recovery image.
Ok. I'm going to try again with "http://en.miui.com/forum.php?mod=viewthread&tid=196175&highlight=sp%2Btool%2Bflash%2Bredmi%2Bnote%2B2"
DarthJabba9 said:
With the SP Flash Tool, all you need is the correct "scatter" file (MT6795_Android_scatter.txt), and the image(s) that you want to flash. If the phone is vibrating, then the SP Flash Tool should be able to connect to it when you click "Download". Just make sure that you first untick everything that you do NOT want to flash. I would try flashing the boot image (boot.img) first. If that succeeds, then try the TWRP recovery image.
Click to expand...
Click to collapse
Well... Install again drivers MTK but nothing... The phone vibrates well but the PC still doesn't see ... It's late now, I look again tomorrow night.
Thanks again.
manu33xtro said:
Ok. I'm going to try again with "http://en.miui.com/forum.php?mod=viewthread&tid=196175&highlight=sp%2Btool%2Bflash%2Bredmi%2Bnote%2B2"
Click to expand...
Click to collapse
manu33xtro said:
Well... Install again drivers MTK but nothing... The phone vibrates well but the PC still doesn't see ... It's late now, I look again tomorrow night.
Thanks again.
Click to expand...
Click to collapse
Perhaps you might want to describe what exactly happens when do you what exactly?
Hi,
Ok that's what I do with an old PC with Win XP.
- install media Tek USB VCOM drivers for Win XP -> installation complete
- launch SP Flash Tool with administrator rights)
- use scatter file from Redmi Note 2 rom
- use download agent "MTK_AllInOne_DA.bin"
- press download button
- connect phone with UCB cable and waiting... and waiting...
- and I can't see it in device manager !
No way again !
I will try again...
DarthJabba9 said:
Perhaps you might want to describe what exactly happens when do you what exactly?
Click to expand...
Click to collapse
manu33xtro said:
Hi,
Ok that's what I do with an old PC with Win XP.
- install media Tek USB VCOM drivers for Win XP -> installation complete
- launch SP Flash Tool with administrator rights)
- use scatter file from Redmi Note 2 rom
- use download agent "MTK_AllInOne_DA.bin"
- press download button
- connect phone with UCB cable and waiting... and waiting...
- and I can't see it in device manager !
No way again !
I will try again...
Click to expand...
Click to collapse
Strange! I am assuming that when you connect the phone with the USB cable, the battery has been removed from the phone? If so, then it should work.
Perhaps you should try first connecting the phone, and then waiting until it has vibrated once or twice, before clicking the "Download" button?
Yes I removed battery before connect the phone to PC. I tried also with battery and nothing changed.
I even changed the cable to be sure.
Which seems to me most strange is that I see nothing in the device manager, as if the phone wasn't connected. Whatever the installed driver is the same result. I think it should at least have the phone on the COM or USB port ...
I will try again this night to be sure with all steps one by one. And I will also try with ACER tablet I and runs Android 5.1. Maybe it will be recognized.
Otherwise I also tried to pass a Linux PC as a last resort.
Thanks again for your help.
DarthJabba9 said:
Strange! I am assuming that when you connect the phone with the USB cable, the battery has been removed from the phone? If so, then it should work.
Perhaps you should try first connecting the phone, and then waiting until it has vibrated once or twice, before clicking the "Download" button?
Click to expand...
Click to collapse
manu33xtro said:
Yes I removed battery before connect the phone to PC. I tried also with battery and nothing changed.
I even changed the cable to be sure.
Which seems to me most strange is that I see nothing in the device manager, as if the phone wasn't connected. Whatever the installed driver is the same result. I think it should at least have the phone on the COM or USB port ...
Click to expand...
Click to collapse
Yes, it should. The fact that the phone vibrates when connected indicates that the PC and phone are communicating - but it may well be that a low-level driver in the phone has been overwritten (which may mean that this is a lost cause). A final idea - can miui recovery access usbotg?
Hum good question. In fact I don't know. I'll ask the MIUI forum.
I got home late from work so I don't do tests tonight, I'd see it all tomorrow including the connection with my tablet ...
Thanks
DarthJabba9 said:
Yes, it should. The fact that the phone vibrates when connected indicates that the PC and phone are communicating - but it may well be that a low-level driver in the phone has been overwritten (which may mean that this is a lost cause). A final idea - can miui recovery access usbotg?
Click to expand...
Click to collapse
Hi,
I tried to connect with an Acer Tablet with Android 5.1.1 but nothing appends...
I tried also with a Linux PC (Debian) and if I can see a Samsung A3 phone dirrectly, no way for my Redmi Note 2...
There really I despair : I think I can't access any of the phone. Can't do anything !
If you have any other solution but you help me a lot already, and thanks for that.
Can be a micro crack on the USB plug into the phone if it's not a software problem ... Let's go for it apart and look at this ...
Thanks again bro.
Manu
DarthJabba9 said:
Yes, it should. The fact that the phone vibrates when connected indicates that the PC and phone are communicating - but it may well be that a low-level driver in the phone has been overwritten (which may mean that this is a lost cause). A final idea - can miui recovery access usbotg?
Click to expand...
Click to collapse
manu33xtro said:
Hi,
I tried to connect with an Acer Tablet with Android 5.1.1 but nothing appends...
I tried also with a Linux PC (Debian) and if I can see a Samsung A3 phone dirrectly, no way for my Redmi Note 2...
There really I despair : I think I can't access any of the phone. Can't do anything !
If you have any other solution but you help me a lot already, and thanks for that.
Can be a micro crack on the USB plug into the phone if it's not a software problem ... Let's go for it apart and look at this ...
Thanks again bro.
Manu
Click to expand...
Click to collapse
I don't think it is a crack on the USB plug. It seems to me to be a low-level driver problem - ie, the drivers on the phone that are active when the phone is not (fully) booted up. I don't have the right terminology for these drivers, but they are possibly part of the bootloader. If that is the problem, then I don't know how you would solve this problem.