Hey Guys,
Currently I am running CM7 RC1.2 MR1, I attempted to upgrade to the CM7 RC1.3 MR2. When the install was finished, there was no radio. So I naturally went back to my back up of MR1.
From what I have found I believe I need to first flash the Radio, then Flash the Rom correct? Are their any steps I can do to insure that I don't boot loop or brick the phone?
Thanks,
Steve
scubaskm said:
Hey Guys,
Currently I am running CM7 RC1.2 MR1, I attempted to upgrade to the CM7 RC1.3 MR2. When the install was finished, there was no radio. So I naturally went back to my back up of MR1.
From what I have found I believe I need to first flash the Radio, then Flash the Rom correct? Are their any steps I can do to insure that I don't boot loop or brick the phone?
Thanks,
Steve
Click to expand...
Click to collapse
You can flash the radio first, or after you install the ROM. I always flash the radio first. The radio is located here http://forum.xda-developers.com/showthread.php?t=1160346 if you want the latest Verizon OTA radio (MR2). Once you download the radio you want to check its MD5 to make sure there were no errors when you downloaded the radio. The MD5 for this radio is 97c195d733f61c6a699528747aff6892 using the program I've attached, you paste the MD5 and load the file into the program and it will tell you if they match. (Rename the attached file to md5.exe instead of md5.exe.zip and run it from your PC). If you flash an incomplete radio you could brick your phone. After you download the radio and check its md5 rename it to PG05IMG.zip and place it on the root of your Micro SD card. Restart your phone holding the bottom volume key down and hboot will ask if you want to install the zip, say yes. Once your radio is flashed boot to ClockworkMod recovery and install the new ROM. Remember to remove or rename the PG05IMG.zip on your Micro SD card after your done or next time you go into hboot it will want to install the radio again.
Awesome thanks. I kinda figured I had it right I just wanted to be sure. Thanks for the md5 checker as well.
Sent from my ThunderBolt using XDA App
WOO, It all worked just fine. Got a little worried when the Rom first started up, but everything is working just fine. WOO.
scubaskm said:
WOO, It all worked just fine. Got a little worried when the Rom first started up, but everything is working just fine. WOO.
Click to expand...
Click to collapse
Awesome. It was smart of you to ask about flashing your radio. It's one of the few ways you can brick your phone if the file is not complete.
Related
So this is my first time installing a rom to my TB. I have installed many roms on my DX but through clockwork.
First question will i need to flash the new radio through Hboot before or after the rom
Second question will i flash the rom through clockwork or from hboot?
I know how to flash via both methods so any direction would be greatly appreciated.
Thanks.
Ohh and I am rooted S-off already.
justcausetx said:
So this is my first time installing a rom to my TB. I have installed many roms on my DX but through clockwork.
First question will i need to flash the new radio through Hboot before or after the rom
Second question will i flash the rom through clockwork or from hboot?
I know how to flash via both methods so any direction would be greatly appreciated.
Thanks.
Ohh and I am rooted S-off already.
Click to expand...
Click to collapse
Radio through Hboot - Before OR After ROM. I did it before, and it worked fine - I've seen some do after, and it works too.
ROM - you can flash from Clockwork recovery, just like you did with your DX (other method is through Rom Manager, but since you're used to flashing through clockwork, I'd just do that (I came from a DX, too))
awesome thanks for the quick response. Hopefully the rom + radio combo will help with battery.
justcausetx said:
awesome thanks for the quick response. Hopefully the rom + radio combo will help with battery.
Click to expand...
Click to collapse
It should - I've been able to jump back to using the stock battery and get a full day's use out of the phone
FYI. There have been some issues with the radio included with Bamf1.5 causing random resets. If that ends up happening to you, Adrynalyne was kind enough to post up some different radios combos to try and avoid any reboot issues. I myself am running great on the radio that comes with Bamf 1.5, so just be ready for that. Switching and trying the different radios, you'll see, is pretty quick anyway, in case you need to.
yea i had upgraded my stock rooted rom to the newest cdma/lte combo from Adrynalyne and it started rebooting so i went back to the original radio cause I didnt feel like messing with it then. Ill have to grab all the combos before i shut my phone down as long as my 4g stays up long enough.
Thanks again for all your help up running Bamf remix 1.5 on the newest radio
justcausetx said:
Thanks again for all your help up running Bamf remix 1.5 on the newest radio
Click to expand...
Click to collapse
I have already experienced one reboot with mine. Lost some settings too.
Sent from my ADR6400L using XDA App
"Please note, this release needs a new radio to complement it.
Put it on sdcard, reboot to hboot and flash."
I flashed the rom just fine, however I'm confused on how to flash the new radio. The new radio zip file is on the SD card....how do I reboot to hboot? Flash it once I'm in hboot? Step by step instructions appreciated.
DontCome2MyHouse said:
"Please note, this release needs a new radio to complement it.
Put it on sdcard, reboot to hboot and flash."
I flashed the rom just fine, however I'm confused on how to flash the new radio. The new radio zip file is on the SD card....how do I reboot to hboot? Flash it once I'm in hboot? Step by step instructions appreciated.
Click to expand...
Click to collapse
Power down, press power and volume down at the same time to get into Hboot. Install the PG zip.
Make sure PG05IMG.zip is on root of sdcard
Power Down
Hold Volume Down and Power button at same time.
hboot will come up and check for PG file
Press power up when asked to start update
Radio will flash
After flashed press power to reboot when it says so.
If you have Clockwork installed it might boot to recovery screen afterwards. If it does just hit the home button on reboot now.
Sent from my ADR6400L using XDA App
Did you flash a Gingerbread radio? That is almost 99% of the time the issue. You can't run 2.0 on stock Froyo radio. If you need help I can help further pm me.
similar issue,
flashed this rom - [ROM][5.25.11] BAMF GingerREMIX v2.0 Beta #5
http://forum.xda-developers.com/showthread.php?t=1095280
Install went fine, but phone would not work and sim card not found. You mention gingerbread radio since froyo wont work. Its not listed in that post that a seperate flash is required. Had to reflash back to bamf 1.63 remix to get phone working.
Any help would be appreciated.
Duroe said:
similar issue,
flashed this rom - [ROM][5.25.11] BAMF GingerREMIX v2.0 Beta #5
http://forum.xda-developers.com/showthread.php?t=1095280
Install went fine, but phone would not work and sim card not found. You mention gingerbread radio since froyo wont work. Its not listed in that post that a seperate flash is required. Had to reflash back to bamf 1.63 remix to get phone working.
Any help would be appreciated.
Click to expand...
Click to collapse
It mentions the GB RUU so that means you have to have it. Which btw it's known to brick your phone without warning.
The reason you did not have any data is because you were still using the froyo radio, to run any of the BAMF 2.0's you need the gingerbread radio.
grab the mr2 radio. that will work
Hacride said:
The reason you did not have any data is because you were still using the froyo radio, to run any of the BAMF 2.0's you need the gingerbread radio.
Click to expand...
Click to collapse
This is what it recommends I do
Things to know:
•A FULL WIPE IS HIGHLY RECOMMENDED!
•This is a leaked GB RUU, it has bugs, all we can do is try our best to squash them! Flash at your own risk.
I thought the gingerbread radio was also included in the rom(my mistake). From a novice point of view. If I do a full wipe and then install bamf 2.0.
1. What method can be utlized to flash the gingerbread radio?
2. What is the correct gingerbread radio for bamf 2.0?
3. Is there a way to flash bamf 2.0 with the updated radio already included in the rom?
Thanks again in advance.
hey mojo they never found the cause of the few bricks so what you said was false and you flash the radio in hboot read the thread on rooting or the radios it tells you all you need to know how to flash it doesnot matter what order you flash the rom and radio just remember to delet the radio file from your sd card once you flashed it
sent via my bamfed out tbolt
Duroe said:
This is what it recommends I do
Things to know:
•A FULL WIPE IS HIGHLY RECOMMENDED!
•This is a leaked GB RUU, it has bugs, all we can do is try our best to squash them! Flash at your own risk.
I thought the gingerbread radio was also included in the rom(my mistake). From a novice point of view. If I do a full wipe and then install bamf 2.0.
1. What method can be utlized to flash the gingerbread radio?
2. What is the correct gingerbread radio for bamf 2.0?
3. Is there a way to flash bamf 2.0 with the updated radio already included in the rom?
Thanks again in advance.
Click to expand...
Click to collapse
Radios are seperate. They need to be flashed in the bootloader. Use the MR2 radio as the other radio bricks your phone.
satseaker said:
hey mojo they never found the cause of the few bricks so what you said was false and you flash the radio in hboot read the thread on rooting or the radios it tells you all you need to know how to flash it doesnot matter what order you flash the rom and radio just remember to delet the radio file from your sd card once you flashed it
sent via my bamfed out tbolt
Click to expand...
Click to collapse
No what you just said was false. Since they don't know where the bricking comes from, it's safe to say that its possibly from that radio. SOOOOOOOO use the MR2 radio instead.
there is no rom with the radio included, put the mr2 on your sd card rename it,reboot the phone and hold the down volume and power button until it brings you into the boot loader it will find the file and ask it u want to update hit the power button wait til its done and reboot
sent via my bamfed out tbolt
satseaker said:
there is no rom with the radio included, put the mr2 on your sd card rename it,reboot the phone and hold the down volume and power button until it brings you into the boot loader it will find the file and ask it u want to update hit the power button wait til its done and reboot
sent via my bamfed out tbolt
Click to expand...
Click to collapse
i think its vol up to start the update. dunno if pressing power starts it to but just in case
ok then explain to me how my phone went into the loop when it never had gingerbread on it,you make an assumtion and then say its the truth that is wrong.
sent via my bamfed out tbolt
satseaker said:
ok then explain to me how my phone went into the loop when it never had gingerbread on it,you make an assumtion and then say its the truth that is wrong.
sent via my bamfed out tbolt
Click to expand...
Click to collapse
Uhhhhhh that can happen for MULTITUDES of reasons. get real. All i'm saying is the cause is not known so use the MR2 one instead. Jeez you kids and always wanting to start ****.
volume down and power gets you the bootloader vol up starts the flash
sent via my bamfed out tbolt
had to go back and read again myself
sent via my bamfed out tbolt
mojonation1487 said:
Radios are seperate. They need to be flashed in the bootloader. Use the MR2 radio as the other radio bricks your phone.
Click to expand...
Click to collapse
I have downloaded the mr2 radio
http://forum.xda-developers.com/showthread.php?t=1115714
Just want to confirm, once I follow the steps I had previously posted,
1. manually flash bamf 2.0 from recovery
2. go in to bootloader and flash m42 radio
I should be up and running? Minus any of the known bugs obviously...
Duroe said:
I have downloaded the mr2 radio
http://forum.xda-developers.com/showthread.php?t=1115714
Just want to confirm, once I follow the steps I had previously posted,
1. manually flash bamf 2.0 from recovery
2. go in to bootloader and flash m42 radio
I should be up and running? Minus any of the known bugs obviously...
Click to expand...
Click to collapse
yup but make sure before you flash anything you wipe data, cache, dalvik cache. After everything is done throw in a fix permissions just for good measure and you're good to go.
Im now up and running with bamf 2.0
Thanks
Thanks all . Bamf Rom running well now with service after Mr2 radio flashed
Sent from my ADR6400L using XDA App
I was trying to flash the PG86IMG in Hboot on my phone after I acquired s-off and it is not working for some reason... I can still get into Team win recovery and still have root and s-off, this pg86img just isn't flashing for some reason.
Is this any signifigance? I also noticed when I tried to flash a rom, it did not work and I had to do my Nandroid recovery.
Any way to fix this so I can install the radio?
Are you trying to flash a radio? Make sure PG86IMG is on the root of you sdcard. Not in any other folder or else the hboot won't see the file. And make sure it is named exactly PG86IMG.zip not PG86IMG.zip.zip. if this doesn't work try using fastboot commands instead, those always work better for me anyways.
mheller91 said:
I was trying to flash the PG86IMG in Hboot on my phone after I acquired s-off and it is not working for some reason... I can still get into Team win recovery and still have root and s-off, this pg86img just isn't flashing for some reason.
Is this any signifigance? I also noticed when I tried to flash a rom, it did not work and I had to do my Nandroid recovery.
Any way to fix this so I can install the radio?
Click to expand...
Click to collapse
What exactly do you mean when you say that it isn't working? Is the bootloader not detecting the file when it scans, or does it find it and then fail to flash when you say yes? What didn't work when you tried flashing a rom? Did it give you an error, or did you get bootloops or something?
i don't think he knows he is not suppose to flash it.
boot into your bootloader and it will run a scan and hit yes if you want to update
okay, so I went into bootloader where it says s-off, I try to update through there, when I click yes to update, it fails. When I tried to flash a rom, it just went to the HTC screen and did nothing. It is weird because my phone is working fine and has root and s-off still...
mheller91 said:
okay, so I went into bootloader where it says s-off, I try to update through there, when I click yes to update, it fails. When I tried to flash a rom, it just went to the HTC screen and did nothing. It is weird because my phone is working fine and has root and s-off still...
Click to expand...
Click to collapse
Does it still say revolutionary at the top of your bootloader? I've seen that some people ran an RUU, still had S-off, but weren't able to flash any unsigned files with the bootloader. They also reported that after running the RUU, the pink Revolutionary banner at the top of the hboot was missing. They had to re-run the Revolutionary tool in order for it to work again. Did you happen to run an RUU at any point in time? If not, ignore.
The only other thing I'd guess is that maybe you got a bad download. Did you check the md5 checksum? If the file is corrupt, redownload it and try flashing it again. Good luck.
Nope! I ran the revolutionary tool and I still have the banner at the top of the menu. It successfully flashed one of the roms on here, rebooted after following all instructions and it was stuck on htc screen.
Also I noticed when I flashed my recovery i had to flash two times in order for it to work..
EDIT: How would I check if the md5 checksum is good or bad? Went through flashing process too and it did say it flashed sucessfully
How do I check if the md5 checksum is good or bad?
PG86IMG.zip
Question. why are you flashing a PG86IMG.zip you already have s off if its just to flash a new radio then the one you have is giving you problem's which i dout but if thats what your wanting to do then so be it all you have to do is download the PG86IMG.zip after that open your dowload folder and long press onthe file and copy it to the root folder of your sd card and then power off and then battery pull then place battery back in and now press volume down and power now you should be in bootloader let it scan for the file then it will ask start update volume up for yes and the update has started but this only work's when you have downloaded the corect PG86IMG.zip file so make sure before you go flashing radio's because if you flash the wrong one well lets just say you will have a new paper waight so make sure you read up on it before flashing
I updated to Cyanogenmod 7 and had no service. I followed the instructions and flashed the stock radio. I've now flashed a few of the different radios but can't get my Thunderbolt to connect to VZW's network.
Anyone have any idea how I can get a connection?
Thanks!
rehughe said:
I updated to Cyanogenmod 7 and had no service. I followed the instructions and flashed the stock radio. I've now flashed a few of the different radios but can't get my Thunderbolt to connect to VZW's network.
Anyone have any idea how I can get a connection?
Thanks!
Click to expand...
Click to collapse
Which RC of CM7?
What "few...different radios"?
Newest version of CM7 no longer supports MR1 and requires one of the following MR2 leak, MR2.5 leak, OTA MR2, or GB leak.
I flashed RC1.4. I've flashed the newest and the oldest on this post. It isn't very clear anywhere which Radio goes with the latest CM7 version.
http://forum.xda-developers.com/showpost.php?p=14752864&postcount=339
Is there a link to a radio that will work?
Appreciate your help!
Is it possible that I'm not flashing the radio correctly? I'm putting the PG05IMG file on my SD, booting in recovery mode, letting it update, and then rebooting.
As far as I thought...this was the proper way to update the radio?
rehughe said:
Is it possible that I'm not flashing the radio correctly? I'm putting the PG05IMG file on my SD, booting in recovery mode, letting it update, and then rebooting.
As far as I thought...this was the proper way to update the radio?
Click to expand...
Click to collapse
No. Radios are not installed via recovery.
Download one of these (either will work)...
OTA MR2: http://forum.xda-developers.com/showthread.php?t=1160346
GB Leak: http://rootzwiki.com/showthread.php?1669-Radio-Leak-7-17-11-2.xx.xxx.x-Radio-New-Gingerbread-RUU
Place the zip of whichever you choose on the root of your sdcard and name it PG05IMG.zip
Boot to hboot (either manually by booting with Power+VolDwn from power-off then select Bootloader or select "Reboot" then "Bootloader" from the Power menu in CM7).
Follow the directions to flash it in bootloader.
Reboot when you are told to.
You should now have service.
Make sure to remove the zip from your sdcard after booting as a safety precaution.
It worked...appreciate the help!!
Absolute_Zero said:
No. Radios are not installed via recovery.
Download one of these (either will work)...
OTA MR2: http://forum.xda-developers.com/showthread.php?t=1160346
GB Leak: http://rootzwiki.com/showthread.php?1669-Radio-Leak-7-17-11-2.xx.xxx.x-Radio-New-Gingerbread-RUU
Place the zip of whichever you choose on the root of your sdcard and name it PG05IMG.zip
Boot to hboot (either manually by booting with Power+VolDwn from power-off then select Bootloader or select "Reboot" then "Bootloader" from the Power menu in CM7).
Follow the directions to flash it in bootloader.
Reboot when you are told to.
You should now have service.
Make sure to remove the zip from your sdcard after booting as a safety precaution.
Click to expand...
Click to collapse
Great info!
Is there any benefit one of these radios to the other?
Thanks,
Bryan
trapperjohn said:
Great info!
Is there any benefit one of these radios to the other?
Thanks,
Bryan
Click to expand...
Click to collapse
Some people seem to have better luck with certain radios. I personally have been getting the best signal strength and battery life with the official OTA MR2 radio. Some people have said they have better luck with one of the leaked radios. I would reccomend trying the official OTA MR2 radio first if you are on a ROM that supports it. The OP of the ROMs thread will say which radios are compatible and recommended.
Sent from my HTC Thunderbolt
So... I flashed scrosler's Stock Rooted RUU 3.14, and once that was cleanly on and working I got into amonra and cleared data, flashed Venasaur 3.1, and then in Hboot ran the 3.14 kernel again.
How did I go wrong and what's the simple fix that will get me with the pokemon? ~thanks <3
(I'm getting bootlooped that is)
You flashed an incompatible kernel. Are you s-on or s-off? If s-off just flash the Rom again in amon ra and reboot phone. No need to install a kernel it will do it for you. If s-on you need the kernel for venasaur Rom which may need to be flashed in fastboot unless someone has made it into a flammable zip. If s-on might as well take the plunge and s-off. It's a very easy process.
sent from my Clean Rezound
I am S-on, as soon as I find something condutable and more reliable than a paperclip i'll probably do S-off haha
I don't think anyway has, I just time getting the image boot file off of the rom and running it in H-boot, I still get a bootloop (I'm genuinely surprised that it didn't work), that's a pretty sticky situation, i'm stuck without a phone until that's solved =(
I repeal that statement, taking the boot.img out and flashing it in hboot worked, wonderful! thanks =)
Question for you?..
Now that that you have your Venusaur 3.1 running..are you having any issues with Wifi?
I did the re-lock, android police ruu, unlock, install recovery, clean wipe x10, install venusaur 3.1, and then installed sense4 boot image for the venusaur rom. However I keep getting Wi-fi Errors, I'm guessing my wifi modules are wrong but I'm just trying to figure out where I may have messed up. I tried flashing the wifi modules provided by http://forum.xda-developers.com/showthread.php?t=1642217 but no go...any ideas?
well i'm fairly curious how you were able to get the sense4 boot image, it gave me a mainver error, I took the boot image out of the rom and ran that.
Which got me in, and wifi isn't giving me a problem surprisingly, but I'm now curious to how your supposed to go 3g with the new setting setup.
My Sd card also can't mount I'm not sure if that's related to 3.14 and pokemon rom or just my terrible flashing
Watercycle, are you still having problems? If you flashed Scott's Rom that is not an ruu. I believe you are still o n the old firmware. You will need to go to nilsp business Rom in the development section and download the old firmware patch (i think it's in the 4th post) then flash in amon ra. You should be set after that.
sent from my Clean Rezound
actually I flashed scott's 3.14 deodex and old firmware patch + boot img before flashing the pokemon and pokemon boot img
I'm currently only struggling with the issue of sd card mount now
Watercycle said:
actually I flashed scott's 3.14 deodex and old firmware patch + boot img before flashing the pokemon and pokemon boot img
I'm currently only struggling with the issue of sd card mount now
Click to expand...
Click to collapse
The patch may still be on your sd card from Scott then and if not go to the thread I suggested. Just boot to recovery and flash the patch again. You will need that patch for any ics Rom you run because you are still on gb firmware. Don't panic your almost there.
sent from my Clean Rezound
how can you tell if your on old gb firmware? =( since it still boots up and works
darnit I thought i was on ics after that full ruu =o
so after having flashed the pokemon in Hboot i flash the old firmware again? (i'm scared it will bootloop me because i finally got it working haha)
ZombieCodeMonkey said:
Question for you?..
Now that that you have your Venusaur 3.1 running..are you having any issues with Wifi?
I did the re-lock, android police ruu, unlock, install recovery, clean wipe x10, install venusaur 3.1, and then installed sense4 boot image for the venusaur rom. However I keep getting Wi-fi Errors, I'm guessing my wifi modules are wrong but I'm just trying to figure out where I may have messed up. I tried flashing the wifi modules provided by http://forum.xda-developers.com/showthread.php?t=1642217 but no go...any ideas?
Click to expand...
Click to collapse
I briefly searched the venasaur thread (which you can do to) and found most people having WiFi issues either had the wrong kernel or just reset their router and bam, WiFi works. I can't help you anymore then that so you may want to ask in that thread.
Edit: did you unzip the Rom and get the boot.IMG there or did you download seperate? If you didn't unzip and take it out of the Rom then try that. You should be good.
sent from my Clean Rezound
What ruu did you use?
sent from my Clean Rezound
Give me like 20 minutes to get back to you...heading home....motorcycle can't multitask at night more obvious to others haha
Sent from my ADR6425LVW using Tapatalk 2
snow, since I sucsessfully was on
This
will flashing the old gingerbread fix my sd mounting or break everything?
sorry I have to be more direct, gotta get some sleep now =)
Watercycle said:
snow, since I sucsessfully was on
This
will flashing the old gingerbread fix my sd mounting or break everything?
sorry I have to be more direct, gotta get some sleep now =)
Click to expand...
Click to collapse
I think so
Watercycle said:
snow, since I sucsessfully was on
This
will flashing the old gingerbread fix my sd mounting or break everything?
sorry I have to be more direct, gotta get some sleep now =)
Click to expand...
Click to collapse
It will fix your sd card. You never ran the ruu if all you flashed was Scott's rooted, deodexd Rom. If you get with me tomorrow I can walk you through the ruu but I think at that point you might as well s-off. Time to find that wire
sent from my Clean Rezound
If you could see your sd card on Scott's Rom it was because of the patch. Make sure you report back. I need some sleep.
sent from my Clean Rezound
Okay...
I re-locked my bootloader using the usual, fastboot oem lock.
then I download the full leaked RUU from Android Police, androidpolice.com/2012/05/07/exclusive-download-htc-rezound-ice-cream-sandwich-build-3-14-605-5-brings-a-handful-of-fixes-and-newer-radios/"
Booted to Hboot with that file on the SD card in the proper name, completely flashed the phone with the Leaked RUU
Once OS loaded, rebooted back to fastboot and used hTcdev.com to unlocked my bootloader again. (I do not have S-Off yet).
Then I downloaded and flashed through fastboot commands the TWRP 2.1.1. Touchscreen recovery.
Once this was done, I downloaded and installed Venusaur 3.1.0 through recovery after performing scot's superwipe x10,
Then fastboot flashed the boot.img for the sense 4.0 roms.
Wi-Fi does not turn on at all...It will state Turning on...but not to long after will give error.
So after all of that I tried grabbing the wifi module.zip from one of the stock rom de-odexed rooted 3.14.605.5 roms, and tried flashing that through recovery and manually adding the file through root explorer..nothing.
Hope that helps clarify.
Also i would through an inquiry to there thread but I don't have enought posts yet to post in development.
ZombieCodeMonkey said:
Okay...
I re-locked my bootloader using the usual, fastboot oem lock.
then I download the full leaked RUU from Android Police, androidpolice.com/2012/05/07/exclusive-download-htc-rezound-ice-cream-sandwich-build-3-14-605-5-brings-a-handful-of-fixes-and-newer-radios/"
Booted to Hboot with that file on the SD card in the proper name, completely flashed the phone with the Leaked RUU
Once OS loaded, rebooted back to fastboot and used hTcdev.com to unlocked my bootloader again. (I do not have S-Off yet).
Then I downloaded and flashed through fastboot commands the TWRP 2.1.1. Touchscreen recovery.
Once this was done, I downloaded and installed Venusaur 3.1.0 through recovery after performing scot's superwipe x10,
Then fastboot flashed the boot.img for the sense 4.0 roms.
Wi-Fi does not turn on at all...It will state Turning on...but not to long after will give error.
So after all of that I tried grabbing the wifi module.zip from one of the stock rom de-odexed rooted 3.14.605.5 roms, and tried flashing that through recovery and manually adding the file through root explorer..nothing.
Hope that helps clarify.
Also i would through an inquiry to there thread but I don't have enought posts yet to post in development.
Click to expand...
Click to collapse
Why are you not s-off? Makes life much easier. What I have concluded is that you need to start over. You have the wrong kernel. Wipe everything then flash the Rom in recovery. You will have had to unzip the Rom on your pc then take the boot.IMG out and flash this in fastboot to the phone. I don't think there is a ph.zip file for this. There are very good directions if you search that thread.
sent from my Clean Rezound
Sorry guys but it's bed time. If you both follow those directions you should be fine. If not get with me in the morning.
sent from my Clean Rezound