i have 2 X10s, one with a broken usb, and one with a broken circuit somewhere that controls the display (no screen using tested working screens).
what i'd like to know.
A is there any known way to cut off the USB part of the PCB and jumper it to another board?
B does anyone know of a fix to a the broken display problem ive described (countless googling found nothing)
C is there a way to exchange the chip holding all the BB and firmware data after flashing with the board with no display?
Related
I have a problem with my XDA2 whereby the 22 pin connector at the bottom of the device has become detached from the main board (after being dropped! outch!)
I have managed to resolder the connector back onto the board, however it appears that a couple of tracks have become detached from the board along with the connector which now means that the serial and usb ports no longer work!! - and there appears to be no way to tell where these pins connect to..
In an attempt to obtain a replacement board i have got hold of a damaged XDA2 from ebay which has a broken screen. However the connector on the board for the screen in this XDA2 is completely different to the one in my XDA2 making it impossible to swap the boards over (or the screens for that matter).
Does anyone know if it is possible to disassemble these displays so that i can produce a display that works with the right connector attached? I know that it's posible to replace the touch screen on these displays but i've no idea how - and i dont want to damage my working display!!
Any help would be apprecated
Rich
So I cracked my LCD screen, bought a replacement, opened up the phone w/ little incident (man they really do cram a lot in there!) and I powered it on.....
the screen is just white, if I fiddle with the connection at where the LCD connects into what I believe is the digitizer I can kind of see a keypad button layout.
What do these symptoms describe and does anyone have a link to the service manual?
Thanks in advance for your time.
I had to replace the LCD on a wizard so here my experience... Make sure the two data ribbons are inserted securely. Also, before you power on, plug your hermes into your computer (assuming your computer is on and logged in as an admin) via USB (this sounds weird but I had to do this for some reason....) and then turn on the wizard.
If you still have a problem, you may have damaged something more than the screen.
Good luck.
Ok I will give plugging it in a shot.
Before you plugged it in what did it do when you powered it on?
anyone else have any input on what the issue could be?
It could be wrong LCD. There are two types of LCD for hermes/wizard with same connector but they are different. One is with gold flex cable, the other is with black flex cable. First one is most popular on wizards, the other on hermes. Check what was the color of your previous lcd flex cable and the new one.
Instructions
Can anyone post the instructions on how to take the lcd apart ?
I have gotten this far
http://www.howardforums.com/showthread.php?t=1152710&page=1&pp=15
I'm a bit afraid to go on without instructions
Here is the lcd I got
http://cnn.cn/shop/8525tytn-touch-p-87.html
hi
i have a htc touch plus or as they call it htc touch dual.digitizer issue it stoped responding so i bought new one fitted in and still the same problem .i think is a software problem i guess driver software for touch screen .if any one can help please
thanks
Touch Dual digitizer
Hi Saliml2
Not convinced it is a software issue. My digitizer on T-Mobile Touch Plus did the same thing. It stated behaving erratically and then stopped responding altogether. I replaced the digitizer (via eBay) and it work for a few days and then stopped again.
I have read around the internet and have tried several ROM updates etc (currently running a WM 6.5.5 found in other area of this forum) but this has not solved the problem.
It seem to be an alignment issue - i.e. screen alignment is outside the screen area, but there seems to be no way of getting it back. Could be a fault on the phone mainboard (?) but there doesn't seem to be any info around apart from sending it to HTC for repair (not viable as the phone value negates this)
My phone is still not working, I might try opening it up again and reseating the digitizer cable but have done this twice already.
Have you try change the flex cable?
I had one to, with the same problem, and after changing the flex everything was ok...
Good luck!
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
deepthought2471 said:
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
Click to expand...
Click to collapse
Maybe this is helpfull http://www.pdacenter.ru/razborka/razbor_htc_touch_dual/
Goodluck
Flex cable, i was mean the cable between the mainboard and the lcd block, you can see it in the previous link, picture 20. Have you try it to change?
hello guys how did you manage to put the digitizer cable in place mine doesn t seem to get in place do i need something to hold the connector in place???
Hello all.
While I was taking my HD2 apart to replace a cracked screen (glass digitizer) I accidentally broke the connector off one of the wires. The wire is black and a few inches long with a silver and round press on connector on each end. It attaches to the board that houses the vibrator motor and runs down the right side of the phone (if you were looking at it face down and partially disassembled).
Unfortunately, I lost the metal piece that broke off the wire (the thing is tiny!), so I can't just solder it back on. Any idea on where I can buy a replacement? I've spent about 6 hours today on ebay and google to no avail. Searching for "HD2 black wire" and anything similar is hardly efficient, but that's all I know about it.
Any help appreciated.
Thanks,
Chris
Good question, I think I damaged the cable to the volume buttons so it would be cool if someone has an adress where we can get spare parts except LCD and Digitizer..
this guy on ebay seems to be selling an HD2 in parts. you might find what you need here:
http://stores.ebay.co.uk/Right-Click-Enterprises/_i.html?_nkw=hd2&submit=Search&_sid=131407386
Thanks, I sent that guy a message and hopefully it'll work out.
Anyone else have a source?
connector of my hd2 is also broken HTC says that the mainboard must be change and I have to pay € 230 because that is my responsibility
I think you have damaged your coaxial cable connector for wifi and bluetooth. Google will help you perhaps.
I believe that my wifi/bluetooth cable is broken, as I have no wifi or bluetooth signal since dropping my phone as reported in a previous post of mine. Can anybody advise me on the difficulty of undertaking this repair myself, does it involve complete disassembly of phone, any soldering etc. If this is the case I don't feel confident enough to do this so does anybody know of someone who does this sort of repair, I have found the cable on e bay for £7 and it looks like it has push on connectors ?
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
WiFi and Bluetooth not working
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
Click to expand...
Click to collapse
Do you think that this is my problem as since I dropped my HD2 I have no wifi (unless sat ontop of router) or bluetooth or fm radio, is it easy to get to the coax cable by removing back cover, whereabouts is it ?
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.[/QUOTE
Fixed it, opened up phone and spotted that at one end of the black wire the connector was not pushed onto the motherboard securely, I pushed it home and hey presto, wifi and Bluetooth now working, phew, Thanks for your help !
Click to expand...
Click to collapse
Hi,
I've been searching and trying to find the correct part to replace the USB charging port without losing the signal. I've gone through different part numbers from different vendors but they always end up being cut up and the original antenna board is placed for the signal to work. Did anyone here have success replacing the charging port board AND signal works with the same board? Can you share the vendor/part number? I'm afraid that cut out of antenna side from the original board will die on me and I'll be stuck with tiny tablet.
Phone is i777.