ARIA power button frex cable ripped.NEED HELP - HTC Aria Q&A, Help & Troubleshooting

ARIA power button frex cable ripped.
Is there any solution to recover it? Anyone knows pinout on mainboard?

No, sorry. The power button is part of the flex cable. You must change the entire flex cable.
You can turn on the phone plugging it to your computer or charger then inserting the battery.

Hello,
This is a little bit old of a thread, however if you have not solved your issue there is a hardware solution. I own an electronics repair store (iRepairNational.com) and we just had a customer in who ripped that flex cable trying to repair the screen. The general steps are:
1) Cut the button PCB portion off the remaing flex cable, remove the tape and metal button cap and solder two micro leads to the button PCB; one to the inner disc (cut a small notch into the side of the PCB so you can access the inner disc without shorting against the outer disc) and one to the outer disc.
2) Solder one of the micro leads to ground, any ground will work.
3) If you examine the bottom of the PCB where the flex originally was sandwiched, you will see two micro SMT resistors. Solder the second lead to the leftmost of the two resistors. Take CARE not to de-solder that SMT resistor by getting it too hot.
4) You will need to flow solder onto the two discs you soldered the leads to originally so the leads do not create bumps preventing the button cap from springing correctly.
5) Replace the button cap/tape and install your now working power button
If this is a little more than you want to get into or you don't have micro soldering tools, we perform the repair for $48.

Related

Screen connector differences and rebuilding displays

I have a problem with my XDA2 whereby the 22 pin connector at the bottom of the device has become detached from the main board (after being dropped! outch!)
I have managed to resolder the connector back onto the board, however it appears that a couple of tracks have become detached from the board along with the connector which now means that the serial and usb ports no longer work!! - and there appears to be no way to tell where these pins connect to..
In an attempt to obtain a replacement board i have got hold of a damaged XDA2 from ebay which has a broken screen. However the connector on the board for the screen in this XDA2 is completely different to the one in my XDA2 making it impossible to swap the boards over (or the screens for that matter).
Does anyone know if it is possible to disassemble these displays so that i can produce a display that works with the right connector attached? I know that it's posible to replace the touch screen on these displays but i've no idea how - and i dont want to damage my working display!!
Any help would be apprecated
Rich

[Q] HELP!!! broken black wire/connector inside HD2

Hello all.
While I was taking my HD2 apart to replace a cracked screen (glass digitizer) I accidentally broke the connector off one of the wires. The wire is black and a few inches long with a silver and round press on connector on each end. It attaches to the board that houses the vibrator motor and runs down the right side of the phone (if you were looking at it face down and partially disassembled).
Unfortunately, I lost the metal piece that broke off the wire (the thing is tiny!), so I can't just solder it back on. Any idea on where I can buy a replacement? I've spent about 6 hours today on ebay and google to no avail. Searching for "HD2 black wire" and anything similar is hardly efficient, but that's all I know about it.
Any help appreciated.
Thanks,
Chris
Good question, I think I damaged the cable to the volume buttons so it would be cool if someone has an adress where we can get spare parts except LCD and Digitizer..
this guy on ebay seems to be selling an HD2 in parts. you might find what you need here:
http://stores.ebay.co.uk/Right-Click-Enterprises/_i.html?_nkw=hd2&submit=Search&_sid=131407386
Thanks, I sent that guy a message and hopefully it'll work out.
Anyone else have a source?
connector of my hd2 is also broken HTC says that the mainboard must be change and I have to pay € 230 because that is my responsibility
I think you have damaged your coaxial cable connector for wifi and bluetooth. Google will help you perhaps.
I believe that my wifi/bluetooth cable is broken, as I have no wifi or bluetooth signal since dropping my phone as reported in a previous post of mine. Can anybody advise me on the difficulty of undertaking this repair myself, does it involve complete disassembly of phone, any soldering etc. If this is the case I don't feel confident enough to do this so does anybody know of someone who does this sort of repair, I have found the cable on e bay for £7 and it looks like it has push on connectors ?
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
WiFi and Bluetooth not working
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
Click to expand...
Click to collapse
Do you think that this is my problem as since I dropped my HD2 I have no wifi (unless sat ontop of router) or bluetooth or fm radio, is it easy to get to the coax cable by removing back cover, whereabouts is it ?
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.[/QUOTE
Fixed it, opened up phone and spotted that at one end of the black wire the connector was not pushed onto the motherboard securely, I pushed it home and hey presto, wifi and Bluetooth now working, phew, Thanks for your help !
Click to expand...
Click to collapse

[Q] replacing the power button and micro usb port

so i managed to mess up the flex cable connected to the power button AND ruin my micro USB port ( i accidentally broke the far left pin, and while trying to replace it drenched the rest in solder) ((internal pins, not external)) does anybody know how i could replace these or fix them without breaking the bank (teenager with no job >.>)
*in case anyone was wondering, i broke them doing this : http://youtu.be/0ga4N_Ih9GE
EDIT: i have an old blackberry with a microusb port somewhere if that could be useful somehow?
edit2: started to wick some of the solder off of the pins with my iron, i dont actually have a wick. unfortunately i have class in the morning and some papers to write so i wont be able to do much. looks like im going back to my old motorola cliq until i can figure this out. anyone have any advice for soldering extremely small connections so maybe i can redo the pins? i have an idea for the power button.

[Q] Need help on how to dismantle Archos G9 80 16GB

I have G9 80 16GB Turbo. The plastic part of the inner micro USB feeder is broken and sticked out to the USB charger pin. My USB charger cable now blocked by that thing and cannot be use anymore. Now in the USB feeder of Archos just remain 4 tiny metals without plastic support (only 4 USB metal pins connector) and not able to take charge by anyway, it is bricked because of no battery power.
It is just 2 months old and no warranty since I bought it in airport transit. 3 times emailed [email protected] with no response as the world has suspected.
1. I've checked my Archos and did not find any screw other than single screw in the USB 3G compartment. I really thankful if anyone can write step-by step dismantle procedure.
2. Can anyone share the shape of USB type soldered to the PCB to enable me order the part and soldering it alone.
3. I've search this on thread : http://forum.xda-developers.com/showthread.php?t=1557506, but the information provided on how to dismantle is not very clear.
4. Thankyou in advance.
cangguek said:
I have G9 80 16GB Turbo. The plastic part of the inner micro USB feeder is broken and sticked out to the USB charger pin. My USB charger cable now blocked by that thing and cannot be use anymore. Now in the USB feeder of Archos just remain 4 tiny metals without plastic support (only 4 USB metal pins connector) and not able to take charge by anyway, it is bricked because of no battery power.
Click to expand...
Click to collapse
Uuups this is bad...
cangguek said:
It is just 2 months old and no warranty since I bought it in airport transit. 3 times emailed [email protected] with no response as the world has suspected.
Click to expand...
Click to collapse
It's sad that they did not reply, but do you think it is covered by warranty if your borked the USB connector?
cangguek said:
1. I've checked my Archos and did not find any screw other than single screw in the USB 3G compartment. I really thankful if anyone can write step-by step dismantle procedure.
Click to expand...
Click to collapse
There's only a single screw at the back.
The housing is hold together by some plastic clamps and it is a pain to open the case (at least compared to a A101IT Gen8).
You really need some force and be very careful not to damage anything...
I'll post a few pics this week in a different thread, because i opened the device last week and it was little bit catchy
cangguek said:
2. Can anyone share the shape of USB type soldered to the PCB to enable me order the part and soldering it alone.
Click to expand...
Click to collapse
Usually this is not an easy task... at least for the unexperienced ones.
Be careful with the thin lines on that PCB.
To unsolder the connector you'll need a lot of heat because it is connected to the gorund plane of the mainboard.
Anyway i don't know the manufacturer, but i guess these MicroUSB connectors are all pretty similar.
So try to catch one, wherever it is sold.
cangguek said:
3. I've search this on thread : http://forum.xda-developers.com/showthread.php?t=1557506, but the information provided on how to dismantle is not very clear.
Click to expand...
Click to collapse
You should start on the opposite side of the connectors and use some plectrums (used by guitar players) to lift off the plastic clamps.
As i said i'll prepare some pics...
EDIT: Here's an overview on how i opened the case.
As already stated it was a pain, and though i had been very careful, some tiny plastics got damaged.
The red circles mark the plastic clamps and the holes they were stucked in respectively.
The green arrows mark the direction i slided my guitar plectrum.
In between you'll have to use something like a screwdriver or putty knife to lift the clamps from their counterparts (this was the evil part).
In the end lift the top of the housing in the yellow direction.
Please take care of the flat cables of the TFT display, don't rip it off!!!
cangguek said:
4. Thankyou in advance.
Click to expand...
Click to collapse
You're welcome!
scholbert
scholbert,
I don't know how should I thanks for your detailed information and photo on your reply.
Below my comment:
1. There is no abuse on the USB port (even no single scratch or dent to prove the abuse, from new I feel it is really tight when I connect the cable into the port, finally the plastic part comes out "cleanly" along with the USB cable connector when I unplug. That's way I try to bet the warranty honor...ray.
2. I've checked eBay and I find many type of micro USB port selling.
3. Based on the generous help you've written I will try to dismantle my Archos when I have spare time within this week.
4. If I may ask, for what purpose you dismantle your Archos. And did you find any problem something like not properly tight when you remantle it again?.
5. From the picture, are all the clamps just on the display side, or mix up and down between the base and display?. Appreciate if you can post the zoom picture of the clamp and the hole to know it's anatomy to make easier when pushing during dismantle process. I also seeing 4 screw-like holes on 4 corner, are they also something like alignment clamps without actual screw?.
6. Big thankyou again for your response.
cangguek said:
4. If I may ask, for what purpose you dismantle your Archos. And did you find any problem something like not properly tight when you remantle it again?.
Click to expand...
Click to collapse
I don't know if i got a second edition device, but i realized this screen issue as well (pressure on the back causes effects on the display).
So i thought i may open it and try to solve this issue.
Anyway i always like to investigate on the construction of these devices...
cangguek said:
5. From the picture, are all the clamps just on the display side, or mix up and down between the base and display?. Appreciate if you can post the zoom picture of the clamp and the hole to know it's anatomy to make easier when pushing during dismantle process. I also seeing 4 screw-like holes on 4 corner, are they also something like alignment clamps without actual screw?.
Click to expand...
Click to collapse
To be exact, the clamps are located all on the base unit.
The display side got the holes for the clamps. I'll see if i could make a more detailed picture, to point you in the right direction.
Though i'm not sure if it helps.
The srew like holes you pointed at are for alignment only.
I also found some glue in the holes, but this is no problem.
Some words on seperation...
It worked out like this on the long side of the housing (upper and lower):
- I tried to seperate the display part and the base with the plectrum step by step
- tried to locate each clamp step by step
- then used a screwdriver
- tried to press gently against the clamp, direction outside to inside
(be very careful and the long side at the bottom, because of the display flex cable)
- then try to lift the parts more and more (it's terrible, but it works)
- keep an eye on the torsion of the display side
(seperate the parts too much, might crack the screen)
I guess i'll prepare some more pics...
Stay tuned!
scholbert
You are really a man god sent to me, thankyou so much. I'm really itching to do the job. First thing I will do once dismantle completed, is to wire two lines for temporary charging until the part I order arrive. If by any chance impossible to replace micro USB port, then I will make hole on the base for common round type DC charging port + and - only.
Hey cangguek,
as promised, here are some detailed views of the clamps (base unit) and holders (display side).
The are four holders in total with two holes each.
The holders are seperate parts and are mounted with three screws in the display part of the housing. Each holder fits into two clamps of the base unit.
Unfortunately they can only get disassembled after you managed to open the housing.
The edge of the clamps point to the border of the base unit housing.
So you may try to push them gently to the inside to release the mating part at the display side.
Anyway i hope things are clear enough now...
Some words on your idea of soldering a DC charging port:
Electrically this would work i guess, but there might be some driver issue which could prevent the unit from charging.
It depends on how the charger is identified by the software driver, which activates the charging process.
On some devices it is required to shorten the data lines of the usb connector, others use the id pin on the micro usb to detect wether a host pc or a wall charger is connected. I don't know how things are done on the Archos 80 G9.
I just wanted to point that out before you start soldering...
Good luck!!!
scholbert
scholbert said:
Some words on your idea of soldering a DC charging port:
Electrically this would work i guess, but there might be some driver issue which could prevent the unit from charging.
It depends on how the charger is identified by the software driver, which activates the charging process.
On some devices it is required to shorten the data lines of the usb connector, others use the id pin on the micro usb to detect wether a host pc or a wall charger is connected. I don't know how things are done on the Archos 80 G9.
I just wanted to point that out before you start soldering...
Click to expand...
Click to collapse
-Data lines are not shorted, charging cable is a fully functional usb cable
-There must be something done to 4th (unused) pin in micro sd plug so device can detect Archos/"normal" cables (my guess- check data lines->if usb host not present check 4th pin->original=fast charge/3rd party=slow charge)
gen_scheisskopf said:
-Data lines are not shorted, charging cable is a fully functional usb cable
Click to expand...
Click to collapse
Yeah i know that the data lines in the cable are not shorted.
AFAIK, they get shorted when connected to the wall charger.
I own a Milestone phone (which definitely requires the lines shorted for charging) and i successfully used the Archos wall charger to charge this device.
At least i wanted to point in this direction...
Thanks for your comment.
Regards,
scholbert
scholbert said:
Yeah i know that the data lines in the cable are not shorted.
AFAIK, they get shorted when connected to the wall charger.
I own a Milestone phone (which definitely requires the lines shorted for charging) and i successfully used the Archos wall charger to charge this device.
At least i wanted to point in this direction...
Thanks for your comment.
Regards,
scholbert
Click to expand...
Click to collapse
Ok
-data lines are shorted together in charger (not to gnd/vcc)
-that's strange but 4th pin seems not to be connected anywhere
sorry, left empty.
Dear scholbert,
All the process as you said really a devil. I am stuck here (at red arrow) and can not proceed unless I tear it with force. Seems there different clamps ?.
Now I am stopping the the job waiting your further help.
Thankyou for helping me:
cangguek said:
Dear scholbert,
All the process as you said really a devil. I am stuck here (at red arrow) and can not proceed unless I tear it with force. Seems there different clamps ?.
Now I am stopping the the job waiting your further help.
Click to expand...
Click to collapse
Yeah i know it hurts... but AFAIK all the clamps are identical.
Nevertheless i realized the same during disassembly.
Some of the clamps did release quite well, at some point i also was afraid i'll break the device into pieces. I'm sorry but i guess you'll have to use gentle force to get it seperated.
BTW, i don't want to be responsible if you damage something
Another warning at this point:
I even did break some small plastics during opening (in the mainboard area), but it doesn't matter in the end, because there are many clamps to hold the parts in place
Good luck!
scholbert
Just to confirm the only screw I removed only the one under the stand stick, I hope I am not missing here. I am still not continuing dismantle process, but at least 40% of the casing has been opened.
cangguek said:
Just to confirm the only screw I removed only the one under the stand stick, I hope I am not missing here.
Click to expand...
Click to collapse
Right, only one screw...
Regards,
scholbert
Man..., wtf, bottom pin of micro-usb (for desoldering purpose) covered with external card slot...grrrrr,....
Please look at the usb pin inside the housing, only metal pins only remain, the plastic part were come-off sticked-out along with usb charger cable. Anyone would come with idea on how to trick my situation?. Removing external card-slot then removing micro USB port seems a big job to me. The solder were very-very tiny...
I have completely separated and disconnect the wires of my Archos, so I have two part now: the base and the display part.
Anyone asking specific picture parts of my Archos, I am ready to shoot.
cangguek said:
Man..., wtf, bottom pin of micro-usb (for desoldering purpose) covered with external card slot...grrrrr,....
Please look at the usb pin inside the housing, only metal pins only remain, the plastic part were come-off sticked-out along with usb charger cable. Anyone would come with idea on how to trick my situation?. Removing external card-slot then removing micro USB port seems a big job to me. The solder were very-very tiny...
I have completely separated and disconnect the wires of my Archos, so I have two part now: the base and the display part.
Anyone asking specific picture parts of my Archos, I am ready to shoot.
Click to expand...
Click to collapse
someone needs to get out the old dustbuster
cangguek said:
Man..., wtf, bottom pin of micro-usb (for desoldering purpose) covered with external card slot...grrrrr,....
Please look at the usb pin inside the housing, only metal pins only remain, the plastic part were come-off sticked-out along with usb charger cable. Anyone would come with idea on how to trick my situation?. Removing external card-slot then removing micro USB port seems a big job to me. The solder were very-very tiny...
I have completely separated and disconnect the wires of my Archos, so I have two part now: the base and the display part.
Anyone asking specific picture parts of my Archos, I am ready to shoot.
View attachment 1057101 View attachment 1057102View attachment 1057103
Click to expand...
Click to collapse
I am happy to see these pictures as they confirm my suspicion. The usb charge port is only soldered on, no screws to hold it in place. That is not a proper mechanical construction and it is no winder it becomes disconnected with only a little use. I have sent 2 units back already which will no longer charge as the mount point has come loose. Number 3 broke too now and as they want me to pay for shipment again ( €50) I am thinking of fixing it myself in stead, but properly..
I have the same problem
Did you eventually repair this problem. If so were did you get the spare part. i have got the same problem. I think i might try returning to my supplier first.
Brilliant tips
scholbert said:
Uuups this is bad...
It's sad that they did not reply, but do you think it is covered by warranty if your borked the USB connector?
There's only a single screw at the back.
The housing is hold together by some plastic clamps and it is a pain to open the case (at least compared to a A101IT Gen8).
You really need some force and be very careful not to damage anything...
I'll post a few pics this week in a different thread, because i opened the device last week and it was little bit catchy
Usually this is not an easy task... at least for the unexperienced ones.
Be careful with the thin lines on that PCB.
To unsolder the connector you'll need a lot of heat because it is connected to the gorund plane of the mainboard.
Anyway i don't know the manufacturer, but i guess these MicroUSB connectors are all pretty similar.
So try to catch one, wherever it is sold.
You should start on the opposite side of the connectors and use some plectrums (used by guitar players) to lift off the plastic clamps.
As i said i'll prepare some pics...
EDIT: Here's an overview on how i opened the case.
As already stated it was a pain, and though i had been very careful, some tiny plastics got damaged.
The red circles mark the plastic clamps and the holes they were stucked in respectively.
The green arrows mark the direction i slided my guitar plectrum.
In between you'll have to use something like a screwdriver or putty knife to lift the clamps from their counterparts (this was the evil part).
In the end lift the top of the housing in the yellow direction.
Please take care of the flat cables of the TFT display, don't rip it off!!!
You're welcome!
scholbert
Click to expand...
Click to collapse
Great tips & will add my own step by step as replacing my screen on G9 after it parachuted from 2 foot onto a rubber floor!!:good:
topsterdog said:
Great tips & will add my own step by step as replacing my screen on G9 after it parachuted from 2 foot onto a rubber floor!!:good:
Click to expand...
Click to collapse
I'd be very interested in this and to learn where you bought the replacement screen...
I have an 80G9 with cracked screen and LCD and busted digitiser.
Sent from my ARCHOS 101G9

[Q] Captivate usb-mainboard problem

I have a captivate with bad usb port it was charging but can't get connected to the computer I opened it up and found out that there is a problem with the board the place where the usb port should be soldered (the pads) is gone.
I'm asking is there a way to put a wire connecting to some place on the board (the place where it should go)????
plzzzzz help me guys !!!!
Wow, that's fried.
I'm amazed that it even charges.
I think that I'd unsolder the connector and scrape all the burnt junk off, glue a new connector on the surface, then run wires to where they should go.
The D+ and D- should be somewhat easy to track down.
Those data lines usually run close together and they go to two "build-out" resistors before they go on to some chip.
Renate NST said:
Wow, that's fried.
I'm amazed that it even charges.
I think that I'd unsolder the connector and scrape all the burnt junk off, glue a new connector on the surface, then run wires to where they should go.
The D+ and D- should be somewhat easy to track down.
Those data lines usually run close together and they go to two "build-out" resistors before they go on to some chip.
Click to expand...
Click to collapse
thanxxx
I tried to track it down but I couldn't so I'm asking if there's any map or a scheme for the mainboard to help me!!!

Categories

Resources