Related
Hi,
First many thanks to all people here at the forum who makes the day better and more interesting for mobile nerds like me. I have been lurking around here for a long time and enjoyed every minute of it.
My problem :
Since my x7500 is SIM unlocked and with a standard setup as far as I can see I tried the HTC VM6 Rom flash without CID unlock.
That was stupid. Very stupid, since I don't have the providers orginal ROM available.
My x7500 will not accept the HTC VM6 ROM and is stuck in Bootloader with "USB" at the bottom of the screen when connected to my PC. Hard reset does not start the normal "installation"
When I start the VM6 flash program I get the famous "provider error message"
Is there any possibility to unlock the CID in Bootloader or "flashing" the bootloader to use the original ROM image at my device for a re-install ? In that way I could use the X7500 unlocker in VM5 and then flash to VM6 after.
If not re-installing the original ROM or unlocking the CID is possible I guess my x7500 is seriously bricked.
I am sorry if the answer to my problem can be found in other treads here. I have searched and read a lot without any success. I know now that I should have unlocked the device before trying to flash -> can only blame my one stupidity.
I will be very happy for every advice.
Greetings, Eric
EricBr said:
Hi,
First many thanks to all people here at the forum who makes the day better and more interesting for mobile nerds like me. I have been lurking around here for a long time and enjoyed every minute of it.
My problem :
Since my x7500 is SIM unlocked and with a standard setup as far as I can see I tried the HTC VM6 Rom flash without CID unlock.
That was stupid. Very stupid, since I don't have the providers orginal ROM available.
My x7500 will not accept the HTC VM6 ROM and is stuck in Bootloader with "USB" at the bottom of the screen when connected to my PC. Hard reset does not start the normal "installation"
When I start the VM6 flash program I get the famous "provider error message"
Is there any possibility to unlock the CID in Bootloader or "flashing" the bootloader to use the original ROM image at my device for a re-install ? In that way I could use the X7500 unlocker in VM5 and then flash to VM6 after.
If not re-installing the original ROM or unlocking the CID is possible I guess my x7500 is seriously bricked.
I am sorry if the answer to my problem can be found in other treads here. I have searched and read a lot without any success. I know now that I should have unlocked the device before trying to flash -> can only blame my one stupidity.
I will be very happy for every advice.
Greetings, Eric
Click to expand...
Click to collapse
There were four ROMs posted here some time ago. At least one of them didn't require the unit to be SPL / CID unlocked. Try to get hold of one of those - look in the Athena WM6 forum (where this should have been posted)
ROM
apd said:
There were four ROMs posted here some time ago. At least one of them didn't require the unit to be SPL / CID unlocked. Try to get hold of one of those - look in the Athena WM6 forum (where this should have been posted)
Click to expand...
Click to collapse
Thanks for reply.
I suppose you mean this four Rom's :
http://uploaded.de/?id=j2pv51 - ROM ver 2.20
for use with the athena_upgrade program
http://uploaded.de/?id=0v9mm1 - flasher for SuperCID devices only
works only for supercid devices
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
http://uploaded.de/?id=wbbw2u - T-MOB005 - version with spl,ipl and etc
works with CID T-MOB005 and SuperCid
As I understand my x7500 is not unlocked/superCid'ed and I need a ROM with exactly the same CID as on my device. Or am I far out ?
Or should I be able to use one of them even if the CID don't match ?
Thanks, Erik
EricBr said:
Thanks for reply.
I suppose you mean this four Rom's :
http://uploaded.de/?id=j2pv51 - ROM ver 2.20
for use with the athena_upgrade program
http://uploaded.de/?id=0v9mm1 - flasher for SuperCID devices only
works only for supercid devices
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
http://uploaded.de/?id=wbbw2u - T-MOB005 - version with spl,ipl and etc
works with CID T-MOB005 and SuperCid
As I understand my x7500 is not unlocked/superCid'ed and I need a ROM with exactly the same CID as on my device. Or am I far out ?
Or should I be able to use one of them even if the CID don't match ?
Thanks, Erik
Click to expand...
Click to collapse
I think you need this one:
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
mackaby007 said:
I think you need this one:
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
Click to expand...
Click to collapse
Hi Mackaby, thanks for the answer.
That was the first ROM I tried to flash. Gave me error message "wrong vendor, check your update software"
Now I only get bootloader when I start my device. I have(had) a Norwegian ROM so I guess the CID does not match. I wish I unlocked my device before trying the WM6 ROM but......
Now I am stuck : Cannot boot / install my original ROM or install any.
My hope is that I can either unlock my CID in Bootloader or installing the original ROM again with a hard reset. To bad a hard reset only sends me to bootloader.
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
pof said:
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
Click to expand...
Click to collapse
Hey Pof,
Welcome to the Athena forum. Are you planning on being here or you were just passing by...
pof said:
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
Click to expand...
Click to collapse
Hi Pof ! Thanks for the answer and clarification. Will try today !
Greetings, Eric
pof said:
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
Click to expand...
Click to collapse
Did it. Same result : Bootloader shows up after "task 8"
bootloader says :
athe100
ipl-v1.00
Athe100
SPL-v1.07.0000
red (raster)
green (raster)
blue (raster)
"Serial" when not USB connected, "USB" when connected in white field.
Guess I have to send my device for service since there are no ROM available for my local X7500 That's life
lpsi2000 said:
Are you planning on being here or you were just passing by...
Click to expand...
Click to collapse
Just passing by, sorry... i don't have athena
EricBr said:
Did it. Same result : Bootloader shows up after "task 8"
[...]
Guess I have to send my device for service since there are no ROM available for my local X7500 That's life
Click to expand...
Click to collapse
bummer..
Eric
As far as I know, all the athenas were provided withe the romcode ...if one hqs got the bonus pack.Just check withe someone for the bonus pack,,ai hope this helps.
hdubli said:
Eric
As far as I know, all the athenas were provided withe the romcode ...if one hqs got the bonus pack.Just check withe someone for the bonus pack,,ai hope this helps.
Click to expand...
Click to collapse
Hi Hdubli,
Thanks for the answer.
Bonus pack ? do you mean the CD that followed my x7500 ? I can check but don't think there are any ROM Flash application on that.
Sorry if I didn't understand your message correct
Greetings, Eric
If u buy bonus pack with athena which includes car kit etc etc, u also get CDs, in which the ROM is also there..so I was asking if u can get hold of the dealer from whom u hv got and enquire about it..also in mtty issue info 2 command check what is yr CID
hdubli said:
If u buy bonus pack with athena which includes car kit etc etc, u also get CDs, in which the ROM is also there..so I was asking if u can get hold of the dealer from whom u hv got and enquire about it..also in mtty issue info 2 command check what is yr CID
Click to expand...
Click to collapse
Ok, understand. We don't have anything called Bonuspack here with hardware stuff and ROM software.
This was the output from the mtty command :
Cmd>info 2
HTCSHTC__H10 ÅPýHTCE
Cmd>info 3
HTCSATHE100001.07.0000 ßؽôHTCE
Anything special with this ?
Anyone who knows if it is possible to mod a ROM flash file so that this CID will be accepted during install ?
EricBr said:
Anyone who knows if it is possible to mod a ROM flash file so that this CID will be accepted during install ?
Click to expand...
Click to collapse
That would corrupt the signatures, and it won't flash with an unmodified bootloader.
bootloader screen freeze after turning htc x7500 off
EricBr said:
Hi,
First many thanks to all people here at the forum who makes the day better and more interesting for mobile nerds like me. I have been lurking around here for a long time and enjoyed every minute of it.
My problem :
Since my x7500 is SIM unlocked and with a standard setup as far as I can see I tried the HTC VM6 Rom flash without CID unlock.
That was stupid. Very stupid, since I don't have the providers orginal ROM available.
My x7500 will not accept the HTC VM6 ROM and is stuck in Bootloader with "USB" at the bottom of the screen when connected to my PC. Hard reset does not start the normal "installation"
When I start the VM6 flash program I get the famous "provider error message"
Is there any possibility to unlock the CID in Bootloader or "flashing" the bootloader to use the original ROM image at my device for a re-install ? In that way I could use the X7500 unlocker in VM5 and then flash to VM6 after.
If not re-installing the original ROM or unlocking the CID is possible I guess my x7500 is seriously bricked.
I am sorry if the answer to my problem can be found in other treads here. I have searched and read a lot without any success. I know now that I should have unlocked the device before trying to flash -> can only blame my one stupidity.
I will be very happy for every advice.
Greetings, Eric
Click to expand...
Click to collapse
Thanks EricBr or anyone who can help me,
I have a similar problem, but in my case I didn't do anything to deserve it... I just turned off my new and provider unlocked x7500 after playing with it all day (just installed skype for mobile and customized some settings, tried the programs, etc.), and when I tried to turn it on again, it just froze in the bootloader screen... Nothing works, I tried soft and hard resets, don't know what else to do?
I've been reading al your posts everywhere and tried a few things without succes, when I conect my x7500 to my pc, it doesn't connect to activesync or anything. I guess I would do better if there would be someone who can create a reply that would clearly guide me on what to do and what files (with links) to download. I simply don't know what happened! since I didn't do anything especial to deserve this from my x7500 which I was falling in love with, after only a few hours of just getting to know it.
I'm new to xda's so please lay it down easy on me... Already had removed the sim and the miniSD I had installed on it... still nothing happens.
ok. it says this in the tri-color screen:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ok. so i download the Hard-SPL-V7 and it works. and it says that up there on my boot loader. but what is my bootloader version? 1.40? or 1.04? and what is this talk of the SPL-2.10.Olipro. how do i get that? im confused
oh another thing. why does it freeze on the GSM- part when i use the SDcard method? anyone? help thank you
the latest bootloader is 2.10.Olipro (the latest official one I've released for general consumption)
to flash it, please do remember NOT to put your phone in bootloader and to have activesync synced.
IPL is Initial Program Loader, and is generally not too exciting.
SPL is Secondary Program Loader and this one handles flashing etc and is the one with the exciting crap you need to patch.
have you been able to flash GSM with SD or somehow else ?
I ve asked how to fix it about 100 times on this forum and my device is still bricked
Hello together,
I got a T-Mobile MDA Vario II upgraded to Windows Mobile 6 and like to use thisone with a Vodafone SIM.
Here some Data about:
(Info from the Bootloader)
HERM300
IPL-1.04
HERM300
SPL-2.03
Systeminformation:
ROM-Version: 3.60.111.4
Radio-Version: 1.50.00.00
I've tried to Downgrade to WM5. I've tried button_rom.
I've tried everything, i have found about Down / Upgrade, about Sim-Unlock etc. etc. etc. ....
But i'm to Stupid to Sim-Unlock this MDA.
Always when I try to Downgrade to WM5, the Setup starts normally.
After the MDA enters the Bootloader the Setup will show an error like "no device....".
What did I wrong?
Please help me :-|
Thank You All!
PS: Sorry for my bad english..i hope, you understand me
tbler said:
Hello together,
I got a T-Mobile MDA Vario II upgraded to Windows Mobile 6 and like to use thisone with a Vodafone SIM.
Here some Data about:
(Info from the Bootloader)
HERM300
IPL-1.04
HERM300
SPL-2.03
Systeminformation:
ROM-Version: 3.60.111.4
Radio-Version: 1.50.00.00
I've tried to Downgrade to WM5. I've tried button_rom.
I've tried everything, i have found about Down / Upgrade, about Sim-Unlock etc. etc. etc. ....
But i'm to Stupid to Sim-Unlock this MDA.
Always when I try to Downgrade to WM5, the Setup starts normally.
After the MDA enters the Bootloader the Setup will show an error like "no device....".
What did I wrong?
Please help me :-|
Thank You All!
PS: Sorry for my bad english..i hope, you understand me
Click to expand...
Click to collapse
I think the RomUpgradeUt.exe that exists in the wm5 ROMs is not compatible with SPL 2.03.
try this:
Extract the .nbh file from your desired wm5 rom (Rename your ROM from *.exe to *.zip and extract it using winzip).
Flash it to your device using RUUwrapper.exe (Force using SSPL).
:,-(
Hey together again,
now i've made the update.
It shows no error or something other.
The MDA looks like a WM5 device - But it will stop booting when it shows the first WM5-Picture.
Ok...now it will stop when it shows the "T-Mobile" Splash Screen..
Well....one Softreset later .... i have a white Screen
This i have already done:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
The SPL is 2.03 again.....
Now I can't go on with the RUUWrapper ......
Is there any posibility to Update the MDA while staying in the Bootloader (works without problems).
Thank You Again
Greetings from Germany
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Hello Again,
i've tried to perform the update this way.....but it won't work :-(
I insert the SD-Card, load the Bootloader, after this, the Display show's:
"Loading...."
After this:
"Checking..."
And for a Short time
"00028002
Not Allowed"
Then I'm in the RGB-Colored Bootloader......
Any Idea? I've tried the WM6-File from the T-Mobile Page, the WM5-File....
No of them will work.
Thanks again!!!!
Have a look through this...
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=41&Itemid=27
might be of use, havent had a change to read it fully so it might not be any help.
tbler said:
Hello Again,
i've tried to perform the update this way.....but it won't work :-(
I insert the SD-Card, load the Bootloader, after this, the Display show's:
"Loading...."
After this:
"Checking..."
And for a Short time
"00028002
Not Allowed"
Then I'm in the RGB-Colored Bootloader......
Any Idea? I've tried the WM6-File from the T-Mobile Page, the WM5-File....
No of them will work.
Thanks again!!!!
Click to expand...
Click to collapse
I don't understand your situation exactly??
Do u have wm6 on your device now?
Can ur device boot into os or not?
Do u have NO GSM error?
Hello,
i've read the manual.
But it won't help me.
The Autor wrote this:
"Connect the device up to activesync using the USB cable, then run RUUWrapper.exe"
My Problem: Windows Mobile 5 or 6 doesn't Boot - So i can't use the RUUWrapper....
To enter the "special" BootLoader I need an working WM5 or WM6....
Do you know, what I mean? My english isn't the best.. sorry :-/
@koorosh_bsboys
- I DON'T have the "NO GSM" Error.
- My OS does not Work.
- The device looks like it's a Windows Mobile 5 (i can't see more, because it doesn't boot | It will stay at the blue Screen ("Windows Mobile" and the Windows Logo)).
- Update per SD-Card brings the following Situation:
I insert the SD-Card, load the Bootloader, after this, the Display show's:
"Loading...."
After this:
"Checking..."
And for a Short time
"00028002
Not Allowed"
Then I'm in the RGB-Colored Bootloader......
please exactly tell us your problem
1.IPL version?
2.SPL version?
3.Can boot into OS?
3.KITL enabled or not? (hold Power+comm manager+left ok buttons and reset with stylus, keep touching them until you see the KITL dialogue - if enabled-)?
4.NO GSM error?(when restarting ur device look out to bottom of the screen, do you see NO GSM)
koorosh_bsboys said:
please exactly tell us your problem
1.IPL version?
Click to expand...
Click to collapse
=> IPL-1.01
koorosh_bsboys said:
2.SPL version?
Click to expand...
Click to collapse
=> SPL-2.03
koorosh_bsboys said:
3.Can boot into OS?
Click to expand...
Click to collapse
=> NO (So i can't run the SSPL)
koorosh_bsboys said:
3.KITL enabled or not? (hold Power+comm manager+left ok buttons and reset with stylus, keep touching them until you see the KITL dialogue - if enabled-)?
Click to expand...
Click to collapse
=> I hold the Buttons for about 1 minute....but i will stay in the 3-Colored-Bootloader - So I think - Not Enabled
koorosh_bsboys said:
4.NO GSM error?(when restarting ur device look out to bottom of the screen, do you see NO GSM)
Click to expand...
Click to collapse
=> Yes, now i've seen the "NO GSM" Error....(http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5 <= Method 2 I've tried...but won't help!)
I know....i made something wrong..but i don't know what :-(
Sorry to tell you that dude!
But welcome to the club of bricked hermeses with spl 2.03.
Until now there is no known sulotion to fix that, unless you want to send ur device to service center!
OK...that's very ****, but i can't change this.. *damn* :-(
I have one more MDA Vario II with WM6, SPL2.03 and IPL 1.01
=> WORKING....
But i think i'll unlock this one by the "T-Mobile-Sim-Unlock-Code".
I won't risk the second mda ;-)
THANK YOU VERY MUCH!
Why Flashing...?
Go to any vodafone store..make your device back to WM6..
say to the guy @ vodafone store that your going on a holiday.. they will give you a key that unlocks the device..
and your done ! ! ! Works for a friend of mine
ElProempie said:
Why Flashing...?
Go to any vodafone store..make your device back to WM6..
say to the guy @ vodafone store that your going on a holiday.. they will give you a key that unlocks the device..
and your done ! ! ! Works for a friend of mine
Click to expand...
Click to collapse
I don't think, that a vodafone store will give me a unlock-code for a t-mobile device.... :O
And the next Problem is, that de MDA doesn't boot the OS and have the "no gsm" error....
I tried to run unlocker, step 1 was successful but during step 2 there was an error and the program crashed.
Now the phone can enter bootloader when I switch on, when I try to flash a ROM I stays on %
Please help
sorry to hear that happend to you as you were trying to unlock your phone....
but when you enter boot loader what does it say at the top?
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Think before you jump to conclusions.
raf1987 said:
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Click to expand...
Click to collapse
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
lakeman said:
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
Click to expand...
Click to collapse
If you put it in bootloader screen (FULL PRESS camera button, while poking reset hole) What does it say on the "SPL" line eg; 1.1, 1.2, or 3.5? and what ROM are you trying to use?.................Hi Lakeman
Jay
athena x7500
please help. i have the same problem.
after flash with athenaunlocker after step 1 ,in step 2 my athena make error and my x7500 cannot power on but i can put it in bootloder made.
when i want to flash it with other rom it take 12% and show error.
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
likebie said:
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
Click to expand...
Click to collapse
you have to load an spl 1.2 rom while in bootloader
make sure you remove your sim and sd card first
I have seen many threads about unlocking the CID for other phones, but none for the HTC-HD2. When I attempt to update my phone I get this error message, "ERROR [294] INVALID VENDOR ID". I assume my locked CID is causing this error, so how do I unlock this? Please help me, I really want to update my phone. Thanks in advance.
bahardman
did you try hspl man
i guess no need to cid unlock
Guidance please on flashing 1.48 when getting vendor id error
Hi there - I am pretty new to all of this. I am trying to flash a standard 1.48 rom upgrade obtained through this forum onto a previously O2 locked HD2. I did get an unlock code - which allows me to use my vodafone sim but when i try to use the standard RUU utility it comes up with the vendor ID error. How do I handle this - happy to be pointed to the right post elsewhere.
Mark
markout57 said:
Hi there - I am pretty new to all of this. I am trying to flash a standard 1.48 rom upgrade obtained through this forum onto a previously O2 locked HD2. I did get an unlock code - which allows me to use my vodafone sim but when i try to use the standard RUU utility it comes up with the vendor ID error. How do I handle this - happy to be pointed to the right post elsewhere.
Mark
Click to expand...
Click to collapse
just because you have a sim unlock does not mean you can flash a rom!
yah and just because you have hspl doesnt mean yu cannot unlock CID
tids2k said:
yah and just because you have hspl doesnt mean yu cannot unlock CID
Click to expand...
Click to collapse
The HSPL that is offered here does, indeed, unlock CID.
It says so in the description of the HSPL and it DOES work.
I have HSPL and a GER Vodafone CID-Lock (damn them). Now, I can flash any ROM and Radio (and, finally the 1.48 official upgrade!).
Cheers.
tids2k said:
yah and just because you have hspl doesnt mean yu cannot unlock CID
Click to expand...
Click to collapse
Ok ok - stop teasing the newbies! From my investigations seems to be HSPL? Whatever that might be.
Sorted - used HSPL and it worked a dream. You guys might be rude to newbies but you do seem to know what you are about.
Thanks all
cid still locked after HSPL2 install
Successfully installed HSPL 2. when i put ATT card in, it still asking for unlock code. Not work for my Tmobile US HD2. ;-(
markout57 said:
Sorted - used HSPL and it worked a dream. You guys might be rude to newbies but you do seem to know what you are about.
Thanks all
Click to expand...
Click to collapse
not a case of being rude at all, just please BROWSE the forum before asking.
clicking HERE works a treat for you.
HD2
Is there a program to CID unlock the HTC HD2? I looked everywhere but they are old and there is nothing about HD2: (
megido said:
Is there a program to CID unlock the HTC HD2? I looked everywhere but they are old and there is nothing about HD2: (
Click to expand...
Click to collapse
what about hspl and hspl2 and hspl3,they all cid unlock it,, (cos i know you didn't mean sim unlock, right?)
any solution
Any one found solution on how cid unlock htc hd2?
v3patel said:
Any one found solution on how cid unlock htc hd2?
Click to expand...
Click to collapse
omg HSPL UNLOCK CID for HD2. is so hard to read in this forum ??
Hi, I've flashed my HTC LEO with the latest HTC ROM with a SD card... and now i've got a SPL 3.03, that is not working with HSPL (even 3rd one).
Does anybody got a technique with MTTY to unlock my CID?
Should I use a Goldcard? or do I have to wait for an hypothetic HPSL4 (that integrate a SPL3.03 hack)?
sam here my HD2 is broken
These is hard xD
fuzzifikation said:
The HSPL that is offered here does, indeed, unlock CID.
It says so in the description of the HSPL and it DOES work.
I have HSPL and a GER Vodafone CID-Lock (damn them). Now, I can flash any ROM and Radio (and, finally the 1.48 official upgrade!).
Cheers.
Click to expand...
Click to collapse
_________________________________________________
Hi
What kinda HSPL can unlock CID
I have tried to unlock the CID for a week and searched for every think i now(Dont judge)
Can someone help me
Mathias
Hi there I have the same problem. I did everything I could and nothing works. I can only get to the bootloader and the info is in:
red screen says:
PB81100 SS-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
green screen says:
Upgrade ROM code error
Please try again
blue screen is empty
white screen says:
Serial
And if I connect to PC it will say USB which is ok.
But what now I am stuck here it will not take any ROM it starts upgrade and freezes at 0% or max 2%
I've tried "Task 29", tried some "mtty" couldn't do it, tried "ROM 3.14" again nothing and it is unbeliveable that nothing works even task 29.
I would appreciate any help cause now it's driving me crazy.
PLEASE HELP PLEASE HELP PLEASE HELP PLEASE HELP PLEASE HELP
jovanovic3 said:
Hi there I have the same problem. I did everything I could and nothing works. I can only get to the bootloader and the info is in:
red screen says:
PB81100 SS-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
green screen says:
Upgrade ROM code error
Please try again
blue screen is empty
white screen says:
Serial
And if I connect to PC it will say USB which is ok.
But what now I am stuck here it will not take any ROM it starts upgrade and freezes at 0% or max 2%
I've tried "Task 29", tried some "mtty" couldn't do it, tried "ROM 3.14" again nothing and it is unbeliveable that nothing works even task 29.
I would appreciate any help cause now it's driving me crazy.
PLEASE HELP PLEASE HELP PLEASE HELP PLEASE HELP PLEASE HELP
Click to expand...
Click to collapse
only the correct rom for your phone will work. go to htc website and find any rom that it lets you download using YOUR phones serial, and flash it.
Thanks mate I will try and let you know what I did.