Related
hey hii guyzzz..... i bought my samsung galaxy ace plus 6 days ago... i rooted it and also installed cwm(clockwork mod) from "http://forum.xda-developers.com/showthread.php?t=1618324"..
today i opened system update then it showed that an update of around 8 mb(maybe more i don't remember)so i updated it and i chose to update now for downloaded update.. my phone restarted and started in cwm-based recovery v5.0.2.8.. and since then whatever i do it starts in it again... i tried to remove battery and start it dint worked then removed my micro sd card nothing worked also tried to root again in download mode nothing worked...i am new to android and was too exited so did all rooting and other stuff.. now i am afraid what to do... i think i have bricked my phone plz help as soon as possible....
SOS
Quick question first - Where are you and what network are you on? Because the one below is for INS India so you may need a different firmware
OK try this.
Download this firmware - Samsung Galaxy Ace Plus GT-S7500 (get both parts)
And the flasher - Odin3 v1.83 GT-S7500
Extract everything to the same folder then do this -
1. Open Odin
2. Make sure phone is totally powered off (Remove battery for 30 seconds then reinsert)
3. Boot the phone into Download Mode. You can do this by pressing and holding down the Volume Down and Home buttons while pressing the Power button until you are welcomed by a green robot indicating you are in Download Mode.
4. Once the phone is in Download mode, connect your phone to your PC while keeping the Odin3 application running.
5. Within a few moments, the ID:COM section in the Odin3 application will turn yellow. This indicates that the necessary drivers for your device have been successfully installed on your computer.
6. In Odin3, click the PDA button. Browse for S7500DDLB1_S7500ODDLB1_S7500DDLB1_HOME.tar.md5 and select it.
7. In the Option section in Odin3, make sure only Auto Reboot and F. Reset Time are checked.
8. Hit the “Start” button in Odin3 to begin flashing the Gingerbread firmware to your phone. It may take 5-10 minutes for the installation process to finish. Your phone should automatically reboot itself.
9. As soon as you see the Samsung splash screen, disconnect your phone from your PC.
10. Switch off your phone completely.
11. Reboot the phone into Recovery Mode. You can do this by holding down the Volume Up and Home buttons, then pressing down the Power button.
12. Once inside recovery, perform a wipe:
Select “wipe data/factory reset”, then select “Yes” on the screen that follows to confirm data wipe.
Select “wipe cache partition”, then select “Yes” on the screen that follows to confirm wiping your phone’s cache partition.
13. Head back to the main menu, then select “Reboot system now” to reboot your device.
(If you have problems with the drivers get these and install - Samsung USB Drivers)
Original instructions from here
Hope this helps unbrick your phone. You may need to re-root after this though
I figured that earlier but thanks... I didn't checked xda-forums...... :thumbup:
Sent from Samsung galaxy ace plus using tapatallk....loxy
reboot system now error
same problem here help me out tooo
plz plz plz
lokeshsaini94 said:
hey hii guyzzz..... i bought my samsung galaxy ace plus 6 days ago... i rooted it and also installed cwm(clockwork mod) from "http://forum.xda-developers.com/showthread.php?t=1618324"..
today i opened system update then it showed that an update of around 8 mb(maybe more i don't remember)so i updated it and i chose to update now for downloaded update.. my phone restarted and started in cwm-based recovery v5.0.2.8.. and since then whatever i do it starts in it again... i tried to remove battery and start it dint worked then removed my micro sd card nothing worked also tried to root again in download mode nothing worked...i am new to android and was too exited so did all rooting and other stuff.. now i am afraid what to do... i think i have bricked my phone plz help as soon as possible....
Click to expand...
Click to collapse
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
mcguirestick said:
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
Click to expand...
Click to collapse
You need to flash a ROM that will wipe your data at once.
Is your phone GT I9100 or GT I9100G?
Jokesy said:
You need to flash a ROM that will wipe your data at once.
Is your phone GT I9100 or GT I9100G?
Click to expand...
Click to collapse
It Is a GT-I9100
mcguirestick said:
It Is a GT-I9100
Click to expand...
Click to collapse
Follow these steps:
1. Download CM9 Resurrection editon
2. Flash CM9 Ressurection edtion via Odin
done.
Let me know how it goes.
Jokesy said:
Follow these steps:
1. Download CM9 Resurrection editon
2. Flash CM9 Ressurection edtion via Odin
done.
Let me know how it goes.
Click to expand...
Click to collapse
Didnt knew roms could be flashed through odin, are they also flashed through the PDA section?
Poroto said:
Didnt knew roms could be flashed through odin, are they also flashed through the PDA section?
Click to expand...
Click to collapse
That is a special .tar edition. You simply flash it just like a single file firmware (as PDA).
Good luck
Jokesy said:
That is a special .tar edition. You simply flash it just like a single file firmware (as PDA).
Good luck
Click to expand...
Click to collapse
Hi Tried it exactly the same im afraid Odin says successful phone reboots then sits at Samsung s2 screen and goes no further
mcguirestick said:
Hi Tried it exactly the same im afraid Odin says successful phone reboots then sits at Samsung s2 screen and goes no further
Click to expand...
Click to collapse
can you enter recovery now?
Jokesy said:
can you enter recovery now?
Click to expand...
Click to collapse
Hi, Nope still can only get to boot load not recovery
mcguirestick said:
Hi, Nope still can only get to boot load not recovery
Click to expand...
Click to collapse
I think your data partition is corrupt, but you can still get it solved.
You need to special .pit file. I'll post you the link (for the .pit file and instructions) very soon
Try this it worked for me
mcguirestick said:
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
Click to expand...
Click to collapse
Try this
Try this step by step and it shoudl work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS, Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!†will appear on the bottom left of the window.
In the Odin window, click on the PDA button and select the I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to 9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS†message on the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
ScottsDesk said:
Try this
Try this step by step and it shoudl work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS, Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!†will appear on the bottom left of the window.
In the Odin window, click on the PDA button and select the I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to 9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS†message on the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
Click to expand...
Click to collapse
Hi Tried it again no luck
mcguirestick said:
Hi Tried it again no luck
Click to expand...
Click to collapse
Sorry for not posting the link for the .pit file.
You can get the pit file here
Use the stock pit file first before trying the patched ones.
Follow the guide in this thread to revive your phone
Good luck
Jokesy said:
Sorry for not posting the link for the .pit file.
You can get the pit file here
Use the stock pit file first before trying the patched ones.
Follow the guide in this thread to revive your phone
Good luck
Click to expand...
Click to collapse
Shall we try the pit by itself or the pit with the rom
//
I belive we have the same problems:
http://forum.xda-developers.com/showthread.php?p=32546472#post32546472 (now that my phone flashs - page 2 -)
marceloasr said:
Shall we try the pit by itself or the pit with the rom
//
I belive we have the same problems:
http://forum.xda-developers.com/showthread.php?p=32546472#post32546472 (now that my phone flashs - page 2 -)
Click to expand...
Click to collapse
his case is milder than yours. he should get his problem fixed by follow the tutorial i posted.
TRY THIS!
mcguirestick said:
Hi Tried it again no luck
Click to expand...
Click to collapse
Try this I did and it worked to get mine booting after a bad update.
I messed around with it using several methods of getting it to boot into download mode until I finally got it to do it. I think I left it plugged into the USB, powered it down until I saw the charging screen, then I proceeded to play with the different ways to hold the buttons to get it to download mode. If you are persistent enough and read a little on booting methods to get bricked phone into download mode you will succed if not then your not for the world of trial and error... the main thing is do the first steps I said before until it works
1. Get into Download Mode (WITH THE PHONE PLUGGED IN) by following the steps below
*Turn off the phone until you get to the charging battery screen (keep in mind, your phone is currently PLUGGED IN)
*Press volume up and down, and power all at once.
*As soon as the screen turns black, release your power button.
2. Unplug phone from USB
or try
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
7. Unplug phone from USB
any how try try try until it works
Once in download mode
Get your files together for your phone, and use Odin 1.85.
Plug into Odin and make sure it shows yellow and its added!
1. Now if your files have like 3 files and the exact .pit file for your phone if available.
I found mine here (Find yous stock firmware for your phone)
CLICK HERE
2. Click the PIT button and browse to your exact .pit file for your phone *It should now have added a check in the re-partition box under the options area of the Odin window. If not CHECK IT!
***If you don't have your .pit don't worry about this unless you suspect, or have a bad partition
3. If you have just 1 file just click the PDA button and load the file. If you have 3 then you will load the PDA file in PDA, the Modem file into PHONE, and the CSC file into CSC, there are way too many phones to link all the files so get you stuff together!
4. Now hit start.
5. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
6. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
7. As soon as the phone shows the first sign of starting up IE Logo or whatever let go of all buttons and using the Vol Up down Choose the Clear Cache option and go through and make sure you factory reset it if you can just for good measure.
8. Reboot
9. Now when the phone shows the first sign of starting up IE Logo or whatever take out battery again to power off
10. Now put it back in and start it in Download mode by pressing Vol Down, Home at the same time then the Power button.
11. Once in download mode Hook up to Odin again and flash it with a root kernel for your phone. Do not ask me just find it. I did it took time but I got all the files together over several days of reading and collecting the correct ones.
12. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
13. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
14. In most roots you will now have a advanced or mounting options and more options to use.
15. I cleared the Cache again, Cleared the Davilik Cache, Went into a option and actually mounted the cache formatted the Cache.
16. Use the option now to restart the phone...
And mine started up installed the apps and I am up and running, nice and smooth and no issues so far
I hope this helps out someone whos just about to go off the deep end, as I was there and patience and trial and error came up with this step by step way to recover mine. Thank me by hitting the little thumbs up THANKS button below this post.
And if your so happy your phone is up show your appreciation by buying me a Pepsi
Jokesy said:
his case is milder than yours. he should get his problem fixed by follow the tutorial i posted.
Click to expand...
Click to collapse
Hi Once again no luck,
I have sent it away to go on a JTAG box will let you know if that fixes it.
I really appreciate all your help.
I will let you know what happens.
thanks
Terry
mcguirestick said:
Hi Once again no luck,
I have sent it away to go on a JTAG box will let you know if that fixes it.
I really appreciate all your help.
I will let you know what happens.
thanks
Terry
Click to expand...
Click to collapse
Sorry for your luck! Cheers!
So I bought this cheap tablet off of ebay and after about a week I connected it into the charger and forgot to unplug it.. Only next morning I saw and when I disconnected it it had turned off. So I turned it on and it was stuck in the newsmy logo and wasn't booting up.
There was nothing on the internet, but somehow I got it working again and for everybody's sake I'm posting what I did here.
First off, even though there are some references that this has allwinner A10 inside, ITS NOT. you will brick this if you flash an allwinner variant kernal.
If you are one of those brave souls who flashed on a allwinner kernals and bricked the thing, you would not be able to go to download mode even. Here is the steps to flash a fresh rom that would resolve most of issues:
1. Download driver pack from the attachment of this post
2. Download RKBatchTool here: http://www.x-drivers.com/catalog/fl...s_electronics/models/rk_batch_tool/27576.html..
3. Now turn off your tablet. If it doesn't turn off press a needle head into the reset pinhole and hold it for 5 seconds
4. Open device manager from your computer
5. Then hold the power on button and volume up(that is the one closer to power button) until it turns on. It'll boot your tab in download mode. After the green robot icon appears connect it to the computer by carefully monitoring device manager of computer
*** If you have flashed an allwinner or other rockchip kernal based ROM earlier and do not go in to download mode or no new device installation in your PC there's a real possibility your download mode combination may have changed. Turn it off by pressing needle to reset pinhole. Then turn off and connect it to PC. Then turn it on and then while in boot screen hold volume up. if not try similar procedure by holding volume down or back buttons. If you see driver installation in the PC and nothing in the tablets screen, thats fine. You can continue with the flasing
6. The driver installation probably will fail. Identify which device that is newly added to the device manager.
7. Right click on the device -> Update Driver. Then manually select -> Have disk then give rockusb file from drivers you just downloaded(if your system is 64-bits use files in amd-64 folder)
8. Then select RK29 as the device and update the driver
9. Now extract and run RKBatchTool and you must see under connected devices button #1 highlighted in green
10. Download official ROM here: http://220.168.57.227:1949/cunchu/20120312T3youhuaruanj.rar
There are other ROMs for T3 here as well. But this is the only thing that works
11. Extract it and give its update.img file path to RKBatchTool FW Path
12. Hit Restore
13. Wait few minutes for flash to complete
14. Then the tab will restart once or twice and will start booting up. This process should take maybe 5 minutes or more. Be patient
15. Then it'll finally boot.
I will post a Jelly Bean ROM for this tab here as soon as I cook one
Comments are much appreciated
Thank you! Thank you! Thank you!
Was searching for a guide to get my brothers Newsmy Newpad T3 up and running.
Thank you for this guide. will definitely try it out and leave a feedback.
P.S. Jellybean sounds interesting.
OK. After spending two days I finally got it to detect the Newsmy Newpad T3.
I had to install Android SDK for the USB drivers. (Don't know if it detected from that.)
Then downloaded super one click root. Found the android drivers in it, and when it asked which driver you want to install I gave "Android Composite" not sure but something in those lines.
Successfully rooted it.
Then off the tab and connect the USB cable, press power and volume up (one that is near the power) and when the tab boots
If it asked for drivers please do same as above
Now run the firmware installer provided inside the update.img folder that you downloaded from the original post by suki300me step 10. It is in Chinese and the first option is to change it to English found on the bottom screen.
If everything is set your tab will be in a black screen only thing you know is that it is on is the sound windows 7 makes when the phone is connected to it. Choose the udate .img file and press upgrade.
It will run up to 3-4 stages and will say data copy error. Remove the cable and press power, it will star installing ICS give it few minutes and you are done.
It took me many attempts so don't give up if it didn't work on your first try. Hope this helps someone.
Boot
Hi
I get one newsmy t3 tablet from my friend. The only problem the system is never loaded (stuck at the boot). I try the power+volume up but just the black screen appaers. Btw only turns on when its plugged. Please give me some tips.
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
[UPDATE] 2/22/2013 11:00pm gmt
I'm able to boot it only if I have it plugged in. I can only use Power + Volume controllers + Reset buttons. I can enter Recovery Mode but I cannot confirm/click on any selection.
Tablet does not get recognized by the computer in "Flashing Mode".
I forced to install the driver for the "Flashing mode" when the tablet is in recovery mode but programs like MSIFlashtool, RKBatchTool, RKAdnroid. (not sure if i correcly used the last 2... but whatever)
spilot said:
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
Click to expand...
Click to collapse
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Jack Jake said:
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Click to expand...
Click to collapse
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Sent from my ARCHOS 80G9 using Tapatalk HD
Quinny899 said:
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Click to expand...
Click to collapse
ADB doesn't recognize it. I tried holding Power + Reset button and did 'adb devices' on Ubuntu and it didn't show anything. On Windows, if I held these 2 buttons, it would show an unknown device in Device Manager. (Mind you, I don't have the Android SDK on Windows, just Linux.)
I can't access any recovery/download mode. Any combination of buttons (Power+VolDown, Power+VolUp/VolDown, Power+VolUP, Power+Home, Power+Back, Power+Settings) would do nothing.
-----------------------------------------------------------------------------------------------------
This what it does when I press Power + Reset Button with a needle. It boots up, splash screen, and stays on black screen (Btw, in this stage, it's Unknown Device in Windows Manager).Once I let go of Reset or Power button, it shuts down.
Turning it on without holding Reset, it would show splash screen, black screen and turns off in about 2 seconds.
Bump.
I've tried playing with it for some time. I can't get it to stay working without pressing power+reset buttons, it always shuts off...
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Sent from my Enjoy 10 Plus using xda app-developers app
mramzi said:
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Click to expand...
Click to collapse
... I was trying all the time to get it work on the PC without plugging the charger. Anyways~
(Tablet's turned off), I plugged charger, I plugged USB, I turned on the tablet and viola it actually worked and booted into OS. However, no buttons work AT ALL, and touch input doesn't work as well.
I tried to get into Recovery Mode and it worked, but I can go up/down using VolUp/VolDow buttons but I cannot click on any thing because the home button don't work nor any other.
Only Power + VolUp + VolDown + Reset buttons work... What to do now?
TL;DR I want to click on 'Update from SD Card' from the Android Recovery but I couldn't get the 'home' button to click enter on the selection. So what's the solution?
bump.
updates:
I tried to place the firmware from the official website as update.img on an SD Card and placed it in the tablet and went into the recovery mode and selected the 'update from sd card' but i couldn't click it. I tried to tap power, home, search, settings and back and nothing worked.
what I've got up until now:
I can boot into the ROM / RecoveryMod as long as I have the charger plugged in the tablet.
For Ubuntu, when I use the command $ tail -f /var/log/syslog and plug in my tablet, it shows this log http://pastebin.com/pBpBUA2Q (it identifies the tablet) [note, the tablet is booted into the ROM]
Also, if I'm in the recovery mode and I plug in the tablet, it would enumerate the USB... ~,~
Bump
bump
spilot said:
bump
Click to expand...
Click to collapse
Please don't bump your thread more than once in 24 hours, it's against the rules
Sent from my Galaxy Nexus using Tapatalk HD
bump
Hello,
I know it has been long since this thread stopped.
I'm currently in his shoes and for the life of me cannot find anything on the web to help me solve my problem.
My MSI Enjoy 10" Plus was flashed with the wrong MSI Enjoy 10" update. Now the tablet only turns on when in "Recovery Mode", but selecting in that mode is not possible using 10" Plus' buttons. Is there anyone from you good people that can help? Please? Thanks.
Uhm...bump?
Bump? Need help from the experts here. Please. I'm desperate.
Thank you very much in advance.
Hello everyone. Today I've accidentally installed wrong ClockWorkMod recovery on my Samsung galaxy GT-I9100. Now phone doesnt turn on, it only freezes on white "Samsung" starting text. I can't even get to the download mode now.. Is the any solution or should I bring it to the tec. service?
Thanks in advice.
What recovery exactly ? In other words, we can't give you any idea of what you can possibly try next unless you tell us precisely what you did.
MistahBungle said:
What recovery exactly ? In other words, we can't give you any idea of what you can possibly try next unless you tell us precisely what you did.
Click to expand...
Click to collapse
I did exactly that's written here: (can not paste the url yet)
Steps to root the Samsung Galaxy S2 I9100G on Android 4.1.2 Jelly Bean
1) Download Rooting package [File name: SU-BB-Installer.Zip] for Galaxy S2 I9100G to the computer
2) Connect the phone to the computer using USB cable and copy the downloaded zip file to the external SD card of the phone
3) Unplug the USB cable from the Galaxy S2 and turn it off
4) Boot the phone into Recovery Mode. Press and hold Volume Up + Home buttons together and then press the Power button until the Samsung logo blinks twice. Now release the Power button but keep pressing the other two buttons until a black background with blue text arrives
5) Using the Volume buttons scroll down to 'apply update from external storage,' select it by pressing the Power button. Then locate the SU-BB-Installer.zip file which is saved on the SD card. Select it using the Power button and confirm installation. The process will take some time
6) Once the installation is completed, return to the recovery menu and reboot the phone by selecting 'reboot system now'
Steps to install CWM Recovery on Galaxy S2 I9100G
1) Download the Blazing kernel file, that contains CWM recovery, for Galaxy S2 and save the zip file on the SD card of the phone
Download links- .....
2) Power off the phone and place the device into recovery mode. Press and hold the Volume Up + Home buttons together then press the Power button until the Samsung logo blinks for two times. Now release the Power button while keep pressing the other two buttons until a black background with blue text is seen
3) Using the Volume buttons scroll to 'apply update from external storage,' select it by pressing the Power button. Now navigate to the downloaded CWM recovery zip file which is saved on the SD card
4) Select the zip file and confirm installation. The process will take some time
5) Once the installation process is completed, return to the recovery menu and select 'reboot system now' to reboot the device
Perhaps a silly question, but was your phone definitely on 4.1.2 at the time?
Personally I prefer the root methods using Odin - you get a lot more feedback as to whether or not things are working.
bringiton8989 said:
Perhaps a silly question, but was your phone definitely on 4.1.2 at the time?
Personally I prefer the root methods using Odin - you get a lot more feedback as to whether or not things are working.
Click to expand...
Click to collapse
Yes it was, but I did't notice that tutorial is for S2 I9100G, because mine is S2 I9100. By the way, is there a chance that usb jig could fix this? Because Im losing hope to start it manually..
You've flashed firmware for a different device, this is why your phone is dead. Take it to someone who does JTAG's, it may be JTAG'able. If a JTAG doesn't work replace motherboard - either a new one by Samsung service centre (expensive) or a 2nd hand one you source yourself & pay a local mobile repair shop to swap (cheaper).
MistahBungle said:
You've flashed firmware for a different device, this is why your phone is dead. Take it to someone who does JTAG's, it may be JTAG'able. If a JTAG doesn't work replace motherboard - either a new one by Samsung service centre (expensive) or a 2nd hand one you source yourself & pay a local mobile repair shop to swap (cheaper).
Click to expand...
Click to collapse
Thank you! And what about usb jig, should I try it?
Of course, given they only cost a couple of bucks on eBay you don't have anything to lose. This might be the 1 in 10,000 where it works in this situation for whatever magical reason. But you do need to be realistic/manage your expectations & buy one expecting it won't work.
Since its dead/bricked, try what ever is neccessary to turn it on. Does the recovery mode work? If it does try to update/flash a stock official firmware for your phone. Do what ever is necessary or get ready to pay for some bucks at the local repair shop.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app