Bricked your Newsmy Newpad T3? Then lets Un-Brick it - Android Q&A, Help & Troubleshooting

So I bought this cheap tablet off of ebay and after about a week I connected it into the charger and forgot to unplug it.. Only next morning I saw and when I disconnected it it had turned off. So I turned it on and it was stuck in the newsmy logo and wasn't booting up.
There was nothing on the internet, but somehow I got it working again and for everybody's sake I'm posting what I did here.
First off, even though there are some references that this has allwinner A10 inside, ITS NOT. you will brick this if you flash an allwinner variant kernal.
If you are one of those brave souls who flashed on a allwinner kernals and bricked the thing, you would not be able to go to download mode even. Here is the steps to flash a fresh rom that would resolve most of issues:
1. Download driver pack from the attachment of this post
2. Download RKBatchTool here: http://www.x-drivers.com/catalog/fl...s_electronics/models/rk_batch_tool/27576.html..
3. Now turn off your tablet. If it doesn't turn off press a needle head into the reset pinhole and hold it for 5 seconds
4. Open device manager from your computer
5. Then hold the power on button and volume up(that is the one closer to power button) until it turns on. It'll boot your tab in download mode. After the green robot icon appears connect it to the computer by carefully monitoring device manager of computer
*** If you have flashed an allwinner or other rockchip kernal based ROM earlier and do not go in to download mode or no new device installation in your PC there's a real possibility your download mode combination may have changed. Turn it off by pressing needle to reset pinhole. Then turn off and connect it to PC. Then turn it on and then while in boot screen hold volume up. if not try similar procedure by holding volume down or back buttons. If you see driver installation in the PC and nothing in the tablets screen, thats fine. You can continue with the flasing
6. The driver installation probably will fail. Identify which device that is newly added to the device manager.
7. Right click on the device -> Update Driver. Then manually select -> Have disk then give rockusb file from drivers you just downloaded(if your system is 64-bits use files in amd-64 folder)
8. Then select RK29 as the device and update the driver
9. Now extract and run RKBatchTool and you must see under connected devices button #1 highlighted in green
10. Download official ROM here: http://220.168.57.227:1949/cunchu/20120312T3youhuaruanj.rar
There are other ROMs for T3 here as well. But this is the only thing that works
11. Extract it and give its update.img file path to RKBatchTool FW Path
12. Hit Restore
13. Wait few minutes for flash to complete
14. Then the tab will restart once or twice and will start booting up. This process should take maybe 5 minutes or more. Be patient
15. Then it'll finally boot.
I will post a Jelly Bean ROM for this tab here as soon as I cook one
Comments are much appreciated

Thank you! Thank you! Thank you!
Was searching for a guide to get my brothers Newsmy Newpad T3 up and running.
Thank you for this guide. will definitely try it out and leave a feedback.
P.S. Jellybean sounds interesting.

OK. After spending two days I finally got it to detect the Newsmy Newpad T3.
I had to install Android SDK for the USB drivers. (Don't know if it detected from that.)
Then downloaded super one click root. Found the android drivers in it, and when it asked which driver you want to install I gave "Android Composite" not sure but something in those lines.
Successfully rooted it.
Then off the tab and connect the USB cable, press power and volume up (one that is near the power) and when the tab boots
If it asked for drivers please do same as above
Now run the firmware installer provided inside the update.img folder that you downloaded from the original post by suki300me step 10. It is in Chinese and the first option is to change it to English found on the bottom screen.
If everything is set your tab will be in a black screen only thing you know is that it is on is the sound windows 7 makes when the phone is connected to it. Choose the udate .img file and press upgrade.
It will run up to 3-4 stages and will say data copy error. Remove the cable and press power, it will star installing ICS give it few minutes and you are done.
It took me many attempts so don't give up if it didn't work on your first try. Hope this helps someone.

Boot
Hi
I get one newsmy t3 tablet from my friend. The only problem the system is never loaded (stuck at the boot). I try the power+volume up but just the black screen appaers. Btw only turns on when its plugged. Please give me some tips.

Related

Zeki 7" Firmware?

Has anybody found a link to any custom or stock firmware for this tablet?
I have a small annoying issue that I am sure could be fixed with a flash, the back button randomly stops working until I reboot.
The baby Einstein on their 800 number thought a factory reset would fix it, then that using the software button was a good enough solution and had no clue about tablets in general. Through Support e-mail they were heading towards wanting me to ship the tablet back rather than supply a link to firmware. I explained to them it doesn't appear to be hardware related as it is random, and reboot fixes it.
im looking for the same firmware man, i have mine bricked :S
How to Flash Zeki TB782B, TB1082B Rom with Livesuit (UnBrick)
gmrastaman said:
im looking for the same firmware man, i have mine bricked :S
Click to expand...
Click to collapse
There is already a different thread on here with the information, but here is how I have personally done it......
Zeki TB782B/TB1082B is using the Allwinner Chip A10.
I search in the web and found the Rom flash steps
Flash Tool LivesuitPack
http://hotfile.com/dl/136803097/cffe...ivers.rar.html
The flash ROM Demo video
http://www.youtube.com/watch?v=238RR-WvhrQ
You can get the Rom at below link
http://depositfiles.com/files/u7ew46yzm
FID HN TB1082B ROM
http://depositfiles.com/files/ay9hhvpyf
FID CF TB782B ROM
http://depositfiles.com/files/0wopipacg
FID BN TB1082B ROM
http://depositfiles.com/files/4uoxkwjc4
FIB BN TB782B ROM
1.Required files: Upgrade tool (Livesuit.exe)
2. Make sure your tablet is fully charged
3. Backup your data, device will be formatted during upgrade
4. The driver and upgrade software work for both Windows XP and Windows 7.
Upgrade Steps:
1. Unzip the upgrade tool and USB drive to your hard drive (recommend to put it in C:\ ).
Double-click the LiveSuitPack_v1.07.exe file, it will automatically install the driver files. Click “OK” to complete the driver installation.
2. Open Livesuit.exe
Double-click to open the upgrade tool LiveSuit.exe
3. Select the firmware
Click “No” to not choose the user upgrade wizard, and click the “Select Firmware” button (the first button from the left) to select the firmware .img file.
4. Turn off your tablet
Make sure the tablet is powered off (Turn it on, press the power button for more than 8 seconds to force power off)
5. Press the key combination to start it in the upgrade mode
a. Press and hold down the “Vol +”, button on TB782B,TB892B or “Home” button on TB1082B
b. Connect the USB cable to tablet and computer
c. After connecting the USB cable, press the power button 6 times quickly (you should get a popup window if done correctly, if not repeat step 5 from beginning)
d. DON’T release the “Vol+” button till the LiveSuit window pops up
e. You can now release the “Vol+” button
(Note: If you install the driver at this time the pop-up dialog box, the path to point to installation directory UsbDriver Livesuit folder, click Next to complete the driver installation prompts).
You should see Livesuit window pops up; otherwise, you didn’t do it correctly, you have to repeat step 4 and 5.
6. Select the format to force upgrade
Livesuit prompt “force format”, click “Yes” (Y). All of the original apps installed will be removed.
We highly recommend mandatory format! ! ! Otherwise the update is not complete and may brick! ! !
7. Upgrade begins
Pop-up “OK to force format” dialog box, select “Yes”, the upgrade begins:
8. The upgrade is complete
Firmware download process lasted about three and a half minutes or so, please wait until the prompt “upgrade successful.”
9. Automatic restart
After the upgrade is complete, your tablet will automatically restart, then you can unplug the USB cable.
Slow start-up time machine for the first time, please be patient.
If the machine does not restart automatically, press and hold the Power button for 8-10 seconds or more to ensure the power switch off, then press the Power button 3 seconds or more to turn on your tablet.
10. Congratulations! You have flashed the firmware.
you can get the Google Play at below link
http://forum.xda-developers.com/show....php?t=1621831
ROM for Zeki TB753b
Do you happen to have the Rom for the TB753b (JB 4.1.1)? I have soft bricked my mom's tablet, and need the rom so I can flash it, and hopefully get her tablet back in working order.
Zeki TBD753B stock rom
I am generally good at finding stuff, but I too can not find the stock rom for the tbd753b 7" zeki tab. Any help would be much appreciated. Thank You
need build.prop
i need the original build.prop to flash to my messed up TB753B. does anyone got it??!!??
dragonfriend0013 said:
i need the original build.prop to flash to my messed up TB753B. does anyone got it??!!??
Click to expand...
Click to collapse
Do you still need the build.prop.original?
Sent from my TBD753B using Tapatalk 4
Got it working
vindicato said:
Do you still need the build.prop.original?
Sent from my TBD753B using Tapatalk 4
Click to expand...
Click to collapse
I was finally able to get access to it through ADB and reset the permissions on the file. all is good now. I do still have problems with the screen "double tapping" though and have not figured out how to fix it. Does yours do the same thing.
The only problem I seem to have is that top left hand corner. Sometimes you have to tap that location a couple of times if that's what you mean
Sent from my TBD753B using Tapatalk 4
---------- Post added at 06:42 PM ---------- Previous post was at 06:37 PM ----------
That and updating my Super su binary...
Sent from my TBD753B using Tapatalk 4
please give the firmware for tb753b
please give the firmware for tb753b. for Livesuit.exe
ROM for TAB ZEKI tbdc1093b
any have de rom for this tab? ZEKI tbdc1093b
fallen links , FID: BN TB782B
Can someone help me? I need this rom , my tablet is brick
Zeki TB782B/TB1082B is using the Allwinner Chip A10.
I search in the web and found the Rom flash steps
Flash Tool LivesuitPack
http://hotfile.com/dl/136803097/cffe...ivers.rar.html
The flash ROM Demo video
http://www.youtube.com/watch?v=238RR-WvhrQ
You can get the Rom at below link
http://depositfiles.com/files/u7ew46yzm
FID HN TB1082B ROM
http://depositfiles.com/files/ay9hhvpyf
FID CF TB782B ROM
http://depositfiles.com/files/0wopipacg
FID BN TB1082B ROM
http://depositfiles.com/files/4uoxkwjc4
FIB BN TB782B ROM
1.Required files: Upgrade tool (Livesuit.exe)
2. Make sure your tablet is fully charged
3. Backup your data, device will be formatted during upgrade
4. The driver and upgrade software work for both Windows XP and Windows 7.
Upgrade Steps:
1. Unzip the upgrade tool and USB drive to your hard drive (recommend to put it in C:\ ).
Double-click the LiveSuitPack_v1.07.exe file, it will automatically install the driver files. Click “OK” to complete the driver installation.
2. Open Livesuit.exe
Double-click to open the upgrade tool LiveSuit.exe
3. Select the firmware
Click “No” to not choose the user upgrade wizard, and click the “Select Firmware” button (the first button from the left) to select the firmware .img file.
4. Turn off your tablet
Make sure the tablet is powered off (Turn it on, press the power button for more than 8 seconds to force power off)
5. Press the key combination to start it in the upgrade mode
a. Press and hold down the “Vol +”, button on TB782B,TB892B or “Home” button on TB1082B
b. Connect the USB cable to tablet and computer
c. After connecting the USB cable, press the power button 6 times quickly (you should get a popup window if done correctly, if not repeat step 5 from beginning)
d. DON’T release the “Vol+” button till the LiveSuit window pops up
e. You can now release the “Vol+” button
(Note: If you install the driver at this time the pop-up dialog box, the path to point to installation directory UsbDriver Livesuit folder, click Next to complete the driver installation prompts).
You should see Livesuit window pops up; otherwise, you didn’t do it correctly, you have to repeat step 4 and 5.
6. Select the format to force upgrade
Livesuit prompt “force format”, click “Yes” (Y). All of the original apps installed will be removed.
We highly recommend mandatory format! ! ! Otherwise the update is not complete and may brick! ! !
7. Upgrade begins
Pop-up “OK to force format” dialog box, select “Yes”, the upgrade begins:
8. The upgrade is complete
Firmware download process lasted about three and a half minutes or so, please wait until the prompt “upgrade successful.”
9. Automatic restart
After the upgrade is complete, your tablet will automatically restart, then you can unplug the USB cable.
Slow start-up time machine for the first time, please be patient.
If the machine does not restart automatically, press and hold the Power button for 8-10 seconds or more to ensure the power switch off, then press the Power button 3 seconds or more to turn on your tablet.
10. Congratulations! You have flashed the firmware.
you can get the Google Play at below link
http://forum.xda-developers.com/show....php?t=1621831[/QUOTE]

Bricked my MSI Enjoy 10" Plus

I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
[UPDATE] 2/22/2013 11:00pm gmt
I'm able to boot it only if I have it plugged in. I can only use Power + Volume controllers + Reset buttons. I can enter Recovery Mode but I cannot confirm/click on any selection.
Tablet does not get recognized by the computer in "Flashing Mode".
I forced to install the driver for the "Flashing mode" when the tablet is in recovery mode but programs like MSIFlashtool, RKBatchTool, RKAdnroid. (not sure if i correcly used the last 2... but whatever)
spilot said:
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
Click to expand...
Click to collapse
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Jack Jake said:
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Click to expand...
Click to collapse
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Sent from my ARCHOS 80G9 using Tapatalk HD
Quinny899 said:
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Click to expand...
Click to collapse
ADB doesn't recognize it. I tried holding Power + Reset button and did 'adb devices' on Ubuntu and it didn't show anything. On Windows, if I held these 2 buttons, it would show an unknown device in Device Manager. (Mind you, I don't have the Android SDK on Windows, just Linux.)
I can't access any recovery/download mode. Any combination of buttons (Power+VolDown, Power+VolUp/VolDown, Power+VolUP, Power+Home, Power+Back, Power+Settings) would do nothing.
-----------------------------------------------------------------------------------------------------
This what it does when I press Power + Reset Button with a needle. It boots up, splash screen, and stays on black screen (Btw, in this stage, it's Unknown Device in Windows Manager).Once I let go of Reset or Power button, it shuts down.
Turning it on without holding Reset, it would show splash screen, black screen and turns off in about 2 seconds.
Bump.
I've tried playing with it for some time. I can't get it to stay working without pressing power+reset buttons, it always shuts off...
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Sent from my Enjoy 10 Plus using xda app-developers app
mramzi said:
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Click to expand...
Click to collapse
... I was trying all the time to get it work on the PC without plugging the charger. Anyways~
(Tablet's turned off), I plugged charger, I plugged USB, I turned on the tablet and viola it actually worked and booted into OS. However, no buttons work AT ALL, and touch input doesn't work as well.
I tried to get into Recovery Mode and it worked, but I can go up/down using VolUp/VolDow buttons but I cannot click on any thing because the home button don't work nor any other.
Only Power + VolUp + VolDown + Reset buttons work... What to do now?
TL;DR I want to click on 'Update from SD Card' from the Android Recovery but I couldn't get the 'home' button to click enter on the selection. So what's the solution?
bump.
updates:
I tried to place the firmware from the official website as update.img on an SD Card and placed it in the tablet and went into the recovery mode and selected the 'update from sd card' but i couldn't click it. I tried to tap power, home, search, settings and back and nothing worked.
what I've got up until now:
I can boot into the ROM / RecoveryMod as long as I have the charger plugged in the tablet.
For Ubuntu, when I use the command $ tail -f /var/log/syslog and plug in my tablet, it shows this log http://pastebin.com/pBpBUA2Q (it identifies the tablet) [note, the tablet is booted into the ROM]
Also, if I'm in the recovery mode and I plug in the tablet, it would enumerate the USB... ~,~
Bump
bump
spilot said:
bump
Click to expand...
Click to collapse
Please don't bump your thread more than once in 24 hours, it's against the rules
Sent from my Galaxy Nexus using Tapatalk HD
bump
Hello,
I know it has been long since this thread stopped.
I'm currently in his shoes and for the life of me cannot find anything on the web to help me solve my problem.
My MSI Enjoy 10" Plus was flashed with the wrong MSI Enjoy 10" update. Now the tablet only turns on when in "Recovery Mode", but selecting in that mode is not possible using 10" Plus' buttons. Is there anyone from you good people that can help? Please? Thanks.
Uhm...bump?
Bump? Need help from the experts here. Please. I'm desperate.
Thank you very much in advance.

[Q] Freelander PX2 Bricked?

Hi all
Today I received my freelander px2. I tried to follow the instructions posted here http://www.pandawillforum.com/showt...-PX2-MTK8389-Quad-Core-(update-Sep-6th-2013)/ to flash the device to the latest clean ROM. I got to the "Download" stage. I clicked the "Download" button and connected my Freelander PX2 with the USB cable.
I was having some issues making Windows 7 actually pick up the "MTK" device and load the correct driver. So I was playing around with the drivers and disconnecting and reconnecting the Freelander PX2 (Whilst leaving the Flash tool on DOWNLOAD mode, which was waiting for me to connect the Freelander PX2)
I must have reconnected it several times in the process of trying to make Windows 7 recognise the device. When I looked at the flash tool I noticed it had got to around 57% with the progress bar and stopped. I can only assume I managed to get the MTK drivers installed correctly at some point but tablet didn't really tell me new software was being uploaded to it. So basically I didn't know the flash tool was sending the new software to the tablet when I must have disconnected it during the process.
I can only assume I've interrupted the NAND flash process? When I try to reconnect the tablet now, it says "USB Device Not Recognized". There doesn't seem to be much support anywhere on the internet for this specific device or issue.
I've tried holding the power button for 30 seconds.. nothing happens
I've tried holding the power button plus volume up button for 30 seconds.. nothing happens
There's also no USB disconnect sound when I hold the power button down? Surely a hard reset should trigger a USB disconnect sound in Windows.
What are my options at this stage? Is it completely dead?
EDIT: Ok, this was a bit strange. I left it yesterday morning and declared it dead. Today I woke up, switched my computer on and plugged it in using a different USB cable and the driver was automatically installed as "MTK preloader". I didn't try to switch the device on yet though, as I wasn't sure if it being recognized was by chance. I didn't ask questions. I just immediately started up the flash tool, hit "download" and re-plugged the USB cable. This time the software finished upload with 100% and a green circle. Then it automatically disconnected from the computer. I hit the power button and it needed some time to charge again (maybe it drained itself last time). A few minutes later the OS booted completely fine. I don't know which one of those things made it worked, the new USB cable or leaving it to discharge for a day.. I just don't know. I'm not taking any chances though, the USB cable is being binned.
Have you flashed the CWM recovery for the px2 yet?
What do you think about the new firmware? I think its alot snappier than the old one. The CWM recovery works a treat (but you have no usb cable lol ) so you cant flash it. If you do want to put the recovery on it, let me know i can help. Cheers
PX2 Bricked
Hi,
Glad you got yours working :good:
I have exactly the same problem and now mine is not reconised :crying:
How long does the flashing actually take ?
When I connected it again this morning it it reconised it and the flash toll started to work.
The green bar and red bars both went to 100% then nothing after 5 mons so I unplugged it.
Now its bricked again :crying:
Any advice guys please ?
Reset
Hi mate sorry to here of your problems. Try pressing the little button between the sim slots, if that doesnt work, press volume + and then power button and keep pressed until it starts. When you flashed it did you get the green circle at the end?
If you get it recognized again do this: ENSURE YOU HAVE FULL BATTERY AND DO NOT INTERUPT THE FLASHING
1/ Start tablet and connect usb data cable, ensure it is connected as Media device (MTP).
2/ Unpack PX2_PC_24-10-13 update to a folder of your choice.
3/ Start Flash tool and click scatter loading on the right, and go to your unpacked folder you made earlier and select MT6589_Android_scatter_emmc check ALL boxes at the bottom are selected.
4/ Now click on downlod button, then switch off tablet. It will either ask to load drivers or start the flashing process.Wait until you see the green circle.
5/ Restart tablet. ENJOY
If you want to put clockwork recovery on it do the following:
1/ Download Freelander_PX2_130717_CWM_recovery.img in post #162 at pandawill put it in a folder and copy MT6589_Android_scatter_emmc from the folder above to the same folder.
2/ Start tablet and connect usb data cable, ensure it is connected as Media device (MTP).
3/ Start Flash tool and click scatter loading on the right, and go to your Freelander_PX2_130717_CWM_recovery.img folder you made earlier and select MT6589_Android_scatter_emmc only recovery option should be checked. Dont worry about the red writing.
4/ Click download and switch off tablet, dont worry about the warning just go ahead anyway, it will only take a couple of seconds and you should see the green circle again.
5/ To check it worked press vol+ and power button to get to recovery ( should be blue text ) if it is congrats you have clockwork recovery.
6/ Enjoy your tablet
Hi,
Thanks for your help but I fear it may be terminal,as when I plug the usb in now I get nothing.
gonna try on a different computor later.
If that fails I fear my PX2 will be leaving via the upstairs window
---------- Post added at 04:43 PM ---------- Previous post was at 03:57 PM ----------
Well it wont even charge now !
I wonder if this could mean a hardware problem or a software not sure ?
Any Ideas guys ?
:crying::crying::crying::crying::crying:
PX2 revival
Hi bazza500, try pressing the reset button between the sim slots it has saved me a couple of times when i thought i had bricked mine.
If you go to the pandawill forum under MTK tablets you will find a thread there dealing with an updated by users flashable firmware with cwm recovery.
Then later if you get it up and running there is a solution to extend the internal memory from 1Gb to 2Gb which reduces the storage by 1Gb. Hope you get it running buddy. Cheers
A few tips
Windows 7 has a glitch where by if the path has Chinese characters in it the flash tool with crash/error. Extract everything to your desktop and delete the chinese characters in the folder names.
Also there's a driver error in Windows 7. Make sure you use the driver install tool to install the MTK drivers. Also make sure the driver is installed and the tablet is recognised before you run the flash tool. That's the error I made, I tried to get the drivers installed whilst running the flash tool and the firmware started flashing when I hadn't realized.
Unlike Samsung and Apple, most Chinese devices don't give you a fancy progress bar on the device. There's almost no feedback the tablet or phone being flashed in most cases.
Thanks for the help guys................
Got my replacement today but have hooked it up to updrade and there was about 3 x colours went to 100% on progress bar now nothing for 15 mins !
Is this normal ?
Well a massive fail again.
Gonna send thos one back and get my money back.
Always a bad idea to by cheap o suppose u het what u pay for.
Sent from my GT-N7000 using xda app-developers app
Ok been awhile but I now have a new one and managed to upgrade the rom.
Only one problem I keep losing phone signal ?
Any ideas?

Pipo M6 pro don´t start anymore

Hi,
my Pipo M6 per wifi hangs itself while starting, i.e. he gets stuck with the loading picture. Indeed, with the Reset he restarts, however, gets stuck also again. After he gets stuck, he can be also switched off no more, except by Reset.
And I also do not come to the Recovery mode, I thought, maybe helps a new firmware. However, sometimes he registers if I hold the keys while starting low-spirited, that Android little manes with open belly and warning sign. see below.
If I hang him by USB on my Win7 pc, a wrong driver's file is installed constantly, either Samsung or HTC, so that the Flashtools register that no suitable device is connected. With the USB driver of Pipo the pc says that that is no suitable driver's file.
What can I do?
And over again for stupid ones: I come to the Recovery fashion, nevertheless, dur volume press ESC and power at the same time, or?
Please, can anybody help me?
Nobody can help?
Is the tablet an fall for garantie?
Anybody any idea?
Please help.
Try one of the 2 methodes
gnom68 said:
Is the tablet an fall for garantie?
Anybody any idea?
Please help.
Click to expand...
Click to collapse
A This is the easiest way: Do a HARDRESET
Recovery Mode (for Factory Reset):
-----------------------------------------------------------
1. [Reset] (on the backside)
2. [Power] + [Vol-]
3. green Android shows up
4. press [Vol-] + [Vol+] + [ESC] together till Menu shows up (if it's not showing up try to press it a few once more)
OR
B For advanced users: Flash the original Firmware (download from here it is a very slow download )
and use the howto which is delivered within the downoad.
Maybe you can find some usefull information here
Hope i could help u. For me it was working fine.....

Azpen A727 Tablet - UnBrick (How to)

{Solved}I have an Azpen A727 i bought from MicroCenter that I bricked.
I found out the solution to unbrick the tablet. First you need the firmware for the version of Android your A727 came with (Jelly Bean or KitKat) which i will provide the links for or you can request from Azpen (which i did and got a response for in 30min), 2nd you need a flashing tool called PheonixUSBPro and a "key" to flash your firmware on the bricked tablet.
1. Follow the instructions on this page for flashing firmware and downloading PhoenixUSBPro here http://www.azpenpc.com/download/detail.php/id-2.html or use the Backup here https://drive.google.com/folderview...JrLUZEYTFjOVF2ajJISy1pdkVCSTgzVlk&usp=sharing
2. a. Firmware and "Key" for A727 Jelly Bean https://drive.google.com/folderview?id=0B53yZ1fbVqxJVnNFSkY2cjFoRjQ&usp=sharing
b. Firmware and "Key" for A727 KitKat (For some reason we have two different versions. If one doesn't work try the other)https://drive.google.com/folderview?id=0B53yZ1fbVqxJZGx2SDVPcWhsWmM&usp=sharing
Note: If anyone is having trouble with PhoenixUSBPro detecting your tablet try holding down the power button and plugging in your tablet from the micro-USB side then press the power button 10 times. Then Windows should be installing the driver so PhoenixUSBPro should detect it now. It worked for me in Windows 7.
If anyone has any problems let me know . Thank you @viper2110 for providing the community with the KitKat firmware.
bricked as well
Were you able to get the device working again?
I bricked mine messing with it today and am trying to fix it.
Have the stock recovery so far if you still need it let me know. xda wont let me attach for some reason
buellonsholes said:
Were you able to get the device working again?
I bricked mine messing with it today and am trying to fix it.
Have the stock recovery so far if you still need it let me know. xda wont let me attach for some reason
Click to expand...
Click to collapse
Yep i fixed it. I edited the first post with the solution
thank you
treecheetahdolo said:
Yep i fixed it. I edited the first post with the solution
Click to expand...
Click to collapse
still trying to figure out adb, livesuit, and eclipse all at once but here we go.
nothing like jumping in and just figuring out whats what lol
no luck
treecheetahdolo said:
{Solved}I have an Azpen A727 i bought from MicroCenter that the camera wasnt working so i decided to install a custom ROM on it instead of bringing back to the store. I was able to root it. But once I flashed a custom ClockWorldMod from http://forum.xda-developers.com/showthread.php?t=2532464 i was bricked.
I found out the solution to unbrick the tablet. First you need the firmware which i will provide the link for or you can request from Azpen (which i did and got a response for in 30min), 2nd you need a flashing tool called PheonixUSBPro and a "key" to flash your firmware on the bricked tablet.
1. Follow the instructions on this page for flashing firmware and downloading PhoenixUSBPro http://www.azpenpc.com/download/detail.php/id-2.html
2. Firmware and "Key" https://drive.google.com/folderview?id=0B53yZ1fbVqxJVnNFSkY2cjFoRjQ&usp=sharing
If anyone has any problems let me know
.
Click to expand...
Click to collapse
Can 't figure out why but after trying many times phoenixpro fails me (trying to use key but red button and green button both arent there)
livesuit wont run either unsure why
only thing i have up and running is sdk manager and im working on learning the steps with it
anyone who can help it would be appreciated. using a windows 8
Very important:
Originally Posted by dsulliii View Post
1) Make sure your A700 is turned off. (Do NOT have the micro-USB end plugged into your A700 at this time, that is for later.)
2) Start LiveSuit on your computer. (The COMPUTER end of your USB cable should be plugged into ONLY your computer at this stage.)
3) Select the ROM that you want to flash to your A700.
4) Hold down the Vol button on your device (I usually hold it down Vol-, not Vol+, but I believe that this device does not matter which.)
5) While holding down Vol, plug the micro-USB end of the cable into your A700. Keep holding down the Vol button.
6) While still holding down the Vol button, WITH the USB cable now connected between your computer and your A700, press and release the A700's Power button 10 times, and wait for a second to a few.
7) The LiveSuit program will detect your A700 going into download mode and begin prompting you for what to do.
8) Follow LiveSuit's recommendations, including formatting. It will take less than 5 minutes.
This wasn't clear to me from the original post.
However I followed the original link and figured it out.
Hope that clears it up for anyone else.
.....
WarezAppz said:
Very important:
Originally Posted by dsulliii View Post
1) Make sure your A700 is turned off. (Do NOT have the micro-USB end plugged into your A700 at this time, that is for later.)
2) Start LiveSuit on your computer. (The COMPUTER end of your USB cable should be plugged into ONLY your computer at this stage.)
3) Select the ROM that you want to flash to your A700.
4) Hold down the Vol button on your device (I usually hold it down Vol-, not Vol+, but I believe that this device does not matter which.)
5) While holding down Vol, plug the micro-USB end of the cable into your A700. Keep holding down the Vol button.
6) While still holding down the Vol button, WITH the USB cable now connected between your computer and your A700, press and release the A700's Power button 10 times, and wait for a second to a few.
7) The LiveSuit program will detect your A700 going into download mode and begin prompting you for what to do.
8) Follow LiveSuit's recommendations, including formatting. It will take less than 5 minutes.
This wasn't clear to me from the original post.
However I followed the original link and figured it out.
Hope that clears it up for anyone else.
Click to expand...
Click to collapse
i'm feeling really dumb here i read that too and am pretty sure i have gotten it into this mode. but its the livesuit software thats the problem i cant get that or the other ones i mentioned to even run. anything i do get to run (phoenix and sdk) dont seem to run correctly. windows 8 is annoying me this week. im trying to get one of my old windows 7 computers up and running and ill try again i guess
WarezAppz said:
Very important:
Originally Posted by dsulliii View Post
1) Make sure your A700 is turned off. (Do NOT have the micro-USB end plugged into your A700 at this time, that is for later.)
2) Start LiveSuit on your computer. (The COMPUTER end of your USB cable should be plugged into ONLY your computer at this stage.)
3) Select the ROM that you want to flash to your A700.
4) Hold down the Vol button on your device (I usually hold it down Vol-, not Vol+, but I believe that this device does not matter which.)
5) While holding down Vol, plug the micro-USB end of the cable into your A700. Keep holding down the Vol button.
6) While still holding down the Vol button, WITH the USB cable now connected between your computer and your A700, press and release the A700's Power button 10 times, and wait for a second to a few.
7) The LiveSuit program will detect your A700 going into download mode and begin prompting you for what to do.
8) Follow LiveSuit's recommendations, including formatting. It will take less than 5 minutes.
This wasn't clear to me from the original post.
However I followed the original link and figured it out.
Hope that clears it up for anyone else.
Click to expand...
Click to collapse
Im pretty sure LiveSuit wont work on the A727 because the CPU is different. The A727 uses an Allwinner thats why we have to use PhoenixUSBPro. Sorry for my late response I dont have internet anymore so I got lucky today getting online, lol.
treecheetahdolo said:
Im pretty sure LiveSuit wont work on the A727 because the CPU is different. The A727 uses an Allwinner thats why we have to use PhoenixUSBPro. Sorry for my late response I dont have internet anymore so I got lucky today getting online, lol.
Click to expand...
Click to collapse
Yeah, sorry I was using PhoenixUSBPro, guilty of not mentioning that.
Anyone else have any luck unbricking the A727 with this method?
Look what I ran across
SDK for Allwinner CPUs?
Now will this aid in someone creating a Android 4.4 image for an Azpen a1023 or at least a custom CWM or TWRP? for one?
answer soon back.
WarezAppz said:
SDK for Allwinner CPUs?
Now will this aid in someone creating a Android 4.4 image for an Azpen a1023 or at least a custom CWM or TWRP? for one?
answer soon back.
Click to expand...
Click to collapse
I dont know but BLuFeNiX started this thread where he did a CWM for an A700 http://forum.xda-developers.com/showthread.php?t=2532464
treecheetahdolo said:
I dont know but BLuFeNiX started this thread where he did a CWM for an A700 http://forum.xda-developers.com/showthread.php?t=2532464
Click to expand...
Click to collapse
Yeah I was aware of that, but that's for an A700
and I am actually interested in A1023, not sure the A700 will work for the A1023
Question. Frozen after reimage.
Hi all! I was able to reimage my A727 with PhoenixUSBPro and the firmware and key linked in the OP, but when it reboots and comes up to the initial screen, it's frozen. Won't take any input. The only thing I can do is force a shutdown with the power button. Am I doing something wrong? Thanks.
TMBackstrom said:
Hi all! I was able to reimage my A727 with PhoenixUSBPro and the firmware and key linked in the OP, but when it reboots and comes up to the initial screen, it's frozen. Won't take any input. The only thing I can do is force a shutdown with the power button. Am I doing something wrong? Thanks.
Click to expand...
Click to collapse
I dont know. Have you tried pressing the reset button?
treecheetahdolo said:
I dont know. Have you tried pressing the reset button?
Click to expand...
Click to collapse
Yup, tried the reset button and resetting back to factory. Still frozen.
I just redownloaded everything from the OP onto a Win 7 Pro x86, instead of on my Win 7 Ultimate x64 system, ran the upload, and it is working fine now. Thanks for all the help. :good:
TMBackstrom said:
I just redownloaded everything from the OP onto a Win 7 Pro x86, instead of on my Win 7 Ultimate x64 system, ran the upload, and it is working fine now. Thanks for all the help. :good:
Click to expand...
Click to collapse
Wow interesting. Im surprised it made a difference. Im glad you have everything up and running now
treecheetahdolo said:
{Solved}I have an Azpen A727 i bought from MicroCenter that I bricked.
I found out the solution to unbrick the tablet. First you need the firmware which i will provide the link for or you can request from Azpen (which i did and got a response for in 30min), 2nd you need a flashing tool called PheonixUSBPro and a "key" to flash your firmware on the bricked tablet.
1. Follow the instructions on this page for flashing firmware and downloading PhoenixUSBPro
2. Firmware and "Key"
If anyone has any problems let me know
Click to expand...
Click to collapse
I also have an azpen tablet that comes up with the azpen logo when switching it on and it just stays there.
I did try your solution above but does not work. The device does not seem to be picked up in PhoenixUSBPro.
In windows device manager it did pick up the device as "USB Developer". I instlled the Google drives and now it shows as "Android Composite ADB Interface". But PhoenixUSBPro still does nit pick it up.
Any ideas what else I can try.
viper2110 said:
I also have an azpen tablet that comes up with the azpen logo when switching it on and it just stays there.
I did try your solution above but does not work. The device does not seem to be picked up in PhoenixUSBPro.
In windows device manager it did pick up the device as "USB Developer". I instlled the Google drives and now it shows as "Android Composite ADB Interface". But PhoenixUSBPro still does nit pick it up.
Any ideas what else I can try.
Click to expand...
Click to collapse
Are you holding down the power button and volume down button while plugging in your tablet like Azpen said?

Categories

Resources