Hi,
my Pipo M6 per wifi hangs itself while starting, i.e. he gets stuck with the loading picture. Indeed, with the Reset he restarts, however, gets stuck also again. After he gets stuck, he can be also switched off no more, except by Reset.
And I also do not come to the Recovery mode, I thought, maybe helps a new firmware. However, sometimes he registers if I hold the keys while starting low-spirited, that Android little manes with open belly and warning sign. see below.
If I hang him by USB on my Win7 pc, a wrong driver's file is installed constantly, either Samsung or HTC, so that the Flashtools register that no suitable device is connected. With the USB driver of Pipo the pc says that that is no suitable driver's file.
What can I do?
And over again for stupid ones: I come to the Recovery fashion, nevertheless, dur volume press ESC and power at the same time, or?
Please, can anybody help me?
Nobody can help?
Is the tablet an fall for garantie?
Anybody any idea?
Please help.
Try one of the 2 methodes
gnom68 said:
Is the tablet an fall for garantie?
Anybody any idea?
Please help.
Click to expand...
Click to collapse
A This is the easiest way: Do a HARDRESET
Recovery Mode (for Factory Reset):
-----------------------------------------------------------
1. [Reset] (on the backside)
2. [Power] + [Vol-]
3. green Android shows up
4. press [Vol-] + [Vol+] + [ESC] together till Menu shows up (if it's not showing up try to press it a few once more)
OR
B For advanced users: Flash the original Firmware (download from here it is a very slow download )
and use the howto which is delivered within the downoad.
Maybe you can find some usefull information here
Hope i could help u. For me it was working fine.....
Related
So I bought this cheap tablet off of ebay and after about a week I connected it into the charger and forgot to unplug it.. Only next morning I saw and when I disconnected it it had turned off. So I turned it on and it was stuck in the newsmy logo and wasn't booting up.
There was nothing on the internet, but somehow I got it working again and for everybody's sake I'm posting what I did here.
First off, even though there are some references that this has allwinner A10 inside, ITS NOT. you will brick this if you flash an allwinner variant kernal.
If you are one of those brave souls who flashed on a allwinner kernals and bricked the thing, you would not be able to go to download mode even. Here is the steps to flash a fresh rom that would resolve most of issues:
1. Download driver pack from the attachment of this post
2. Download RKBatchTool here: http://www.x-drivers.com/catalog/fl...s_electronics/models/rk_batch_tool/27576.html..
3. Now turn off your tablet. If it doesn't turn off press a needle head into the reset pinhole and hold it for 5 seconds
4. Open device manager from your computer
5. Then hold the power on button and volume up(that is the one closer to power button) until it turns on. It'll boot your tab in download mode. After the green robot icon appears connect it to the computer by carefully monitoring device manager of computer
*** If you have flashed an allwinner or other rockchip kernal based ROM earlier and do not go in to download mode or no new device installation in your PC there's a real possibility your download mode combination may have changed. Turn it off by pressing needle to reset pinhole. Then turn off and connect it to PC. Then turn it on and then while in boot screen hold volume up. if not try similar procedure by holding volume down or back buttons. If you see driver installation in the PC and nothing in the tablets screen, thats fine. You can continue with the flasing
6. The driver installation probably will fail. Identify which device that is newly added to the device manager.
7. Right click on the device -> Update Driver. Then manually select -> Have disk then give rockusb file from drivers you just downloaded(if your system is 64-bits use files in amd-64 folder)
8. Then select RK29 as the device and update the driver
9. Now extract and run RKBatchTool and you must see under connected devices button #1 highlighted in green
10. Download official ROM here: http://220.168.57.227:1949/cunchu/20120312T3youhuaruanj.rar
There are other ROMs for T3 here as well. But this is the only thing that works
11. Extract it and give its update.img file path to RKBatchTool FW Path
12. Hit Restore
13. Wait few minutes for flash to complete
14. Then the tab will restart once or twice and will start booting up. This process should take maybe 5 minutes or more. Be patient
15. Then it'll finally boot.
I will post a Jelly Bean ROM for this tab here as soon as I cook one
Comments are much appreciated
Thank you! Thank you! Thank you!
Was searching for a guide to get my brothers Newsmy Newpad T3 up and running.
Thank you for this guide. will definitely try it out and leave a feedback.
P.S. Jellybean sounds interesting.
OK. After spending two days I finally got it to detect the Newsmy Newpad T3.
I had to install Android SDK for the USB drivers. (Don't know if it detected from that.)
Then downloaded super one click root. Found the android drivers in it, and when it asked which driver you want to install I gave "Android Composite" not sure but something in those lines.
Successfully rooted it.
Then off the tab and connect the USB cable, press power and volume up (one that is near the power) and when the tab boots
If it asked for drivers please do same as above
Now run the firmware installer provided inside the update.img folder that you downloaded from the original post by suki300me step 10. It is in Chinese and the first option is to change it to English found on the bottom screen.
If everything is set your tab will be in a black screen only thing you know is that it is on is the sound windows 7 makes when the phone is connected to it. Choose the udate .img file and press upgrade.
It will run up to 3-4 stages and will say data copy error. Remove the cable and press power, it will star installing ICS give it few minutes and you are done.
It took me many attempts so don't give up if it didn't work on your first try. Hope this helps someone.
Boot
Hi
I get one newsmy t3 tablet from my friend. The only problem the system is never loaded (stuck at the boot). I try the power+volume up but just the black screen appaers. Btw only turns on when its plugged. Please give me some tips.
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
[UPDATE] 2/22/2013 11:00pm gmt
I'm able to boot it only if I have it plugged in. I can only use Power + Volume controllers + Reset buttons. I can enter Recovery Mode but I cannot confirm/click on any selection.
Tablet does not get recognized by the computer in "Flashing Mode".
I forced to install the driver for the "Flashing mode" when the tablet is in recovery mode but programs like MSIFlashtool, RKBatchTool, RKAdnroid. (not sure if i correcly used the last 2... but whatever)
spilot said:
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
Click to expand...
Click to collapse
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Jack Jake said:
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Click to expand...
Click to collapse
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Sent from my ARCHOS 80G9 using Tapatalk HD
Quinny899 said:
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Click to expand...
Click to collapse
ADB doesn't recognize it. I tried holding Power + Reset button and did 'adb devices' on Ubuntu and it didn't show anything. On Windows, if I held these 2 buttons, it would show an unknown device in Device Manager. (Mind you, I don't have the Android SDK on Windows, just Linux.)
I can't access any recovery/download mode. Any combination of buttons (Power+VolDown, Power+VolUp/VolDown, Power+VolUP, Power+Home, Power+Back, Power+Settings) would do nothing.
-----------------------------------------------------------------------------------------------------
This what it does when I press Power + Reset Button with a needle. It boots up, splash screen, and stays on black screen (Btw, in this stage, it's Unknown Device in Windows Manager).Once I let go of Reset or Power button, it shuts down.
Turning it on without holding Reset, it would show splash screen, black screen and turns off in about 2 seconds.
Bump.
I've tried playing with it for some time. I can't get it to stay working without pressing power+reset buttons, it always shuts off...
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Sent from my Enjoy 10 Plus using xda app-developers app
mramzi said:
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Click to expand...
Click to collapse
... I was trying all the time to get it work on the PC without plugging the charger. Anyways~
(Tablet's turned off), I plugged charger, I plugged USB, I turned on the tablet and viola it actually worked and booted into OS. However, no buttons work AT ALL, and touch input doesn't work as well.
I tried to get into Recovery Mode and it worked, but I can go up/down using VolUp/VolDow buttons but I cannot click on any thing because the home button don't work nor any other.
Only Power + VolUp + VolDown + Reset buttons work... What to do now?
TL;DR I want to click on 'Update from SD Card' from the Android Recovery but I couldn't get the 'home' button to click enter on the selection. So what's the solution?
bump.
updates:
I tried to place the firmware from the official website as update.img on an SD Card and placed it in the tablet and went into the recovery mode and selected the 'update from sd card' but i couldn't click it. I tried to tap power, home, search, settings and back and nothing worked.
what I've got up until now:
I can boot into the ROM / RecoveryMod as long as I have the charger plugged in the tablet.
For Ubuntu, when I use the command $ tail -f /var/log/syslog and plug in my tablet, it shows this log http://pastebin.com/pBpBUA2Q (it identifies the tablet) [note, the tablet is booted into the ROM]
Also, if I'm in the recovery mode and I plug in the tablet, it would enumerate the USB... ~,~
Bump
bump
spilot said:
bump
Click to expand...
Click to collapse
Please don't bump your thread more than once in 24 hours, it's against the rules
Sent from my Galaxy Nexus using Tapatalk HD
bump
Hello,
I know it has been long since this thread stopped.
I'm currently in his shoes and for the life of me cannot find anything on the web to help me solve my problem.
My MSI Enjoy 10" Plus was flashed with the wrong MSI Enjoy 10" update. Now the tablet only turns on when in "Recovery Mode", but selecting in that mode is not possible using 10" Plus' buttons. Is there anyone from you good people that can help? Please? Thanks.
Uhm...bump?
Bump? Need help from the experts here. Please. I'm desperate.
Thank you very much in advance.
Hopefully someone can help me, my child has a Pendo Pad 7 Model no.PNDPP44QC7 with Kitkat 4.4 and it ended up with lots of malware/viruses and barely usable. This tablet only has a power button and no other buttons so I did not know how to boot into recovery mode to do factory reset and after trying reset through settings which made no difference so I gave the device ROOT access so I could try and delete the malware etc but of course i did not do any sort of backup and did not add CWM or TWRP recovery. I ended up deleting something wrong and now the device just hangs on the Pendo logo screen. I have since worked out how to boot into Recovery Mode and also Fastboot mode now but a bit too late I tried to do a wipe data/factory reset and this made no difference still hangs on Pendo logo.
I can't seem to find a CWM or TWRP image file to suit the tablet and possibly try putting tablet into fastboot mode and using ADB on computer and flash the recovery to tablet. ???
in recovery mode options i get are
apply update from ADB
apply update from sdcard
apply update from cache
wipe data/factory reset
wipe cache partition
backup user data
restore user data
but i can not seem to find any correct files to work with this tablet any help to get this tablet working again would be much appreciated Thanks
Good day! how did you manage to boot into Recovery Mode or Fast Mode?
After pressing the power button and seeing the display turn on. Keep spamming the power button and a menu will pop-up on screen with boot options. Short press of the power button cycles through the options, long press selects the option.
Mine was also stuck on a boot loop, even though I had not played around with any settings or tried to root etc. I was able to revive it by going into recovery mode and doing a factory reset.
Hey OP I've got hold of the same tablet I'm working on getting a rom dump atm. Bare with me I'll try and send a link for the img. If u can get into recovery mode where u can update zip. That's good if not try and via pc. Once u have a link to the tablets boatloader, rest is history.
Hi,
Wondering if I can follow up on this.
Mine is stuck on the PENDO boot screen, and I have tried the reset button, as well as the se commands PENDO suggested....
1. Press On/Off Switch (Power), wait for the Pendo Logo start up screen, and then press On/Off Switch (Power) twice right away.
2. Factory mode menu comes out after 10 seconds, two fingers touches panel together to move to select the one like the following picture shows (no need to understand the Chinese words, just follow through as what the picture shows)
3. Press On/Off Switch (Power) and the following picture below will show, press On/Off Switch (Power) again to proceed on Recovery Mode, and wait for system to restart.
Unfortunately, nothing still happens.
ADB will not reveal what device it is, nor will Win 10 recognise the device for it to show in Device Manager or connected devices.
Windows responds with a ding ding, but nothing shows up.
I am stuck, and any info gladly accepted.
Thanks
bump please
ozviewer said:
Hi,
Wondering if I can follow up on this.
Mine is stuck on the PENDO boot screen, and I have tried the reset button, as well as the se commands PENDO suggested....
1. Press On/Off Switch (Power), wait for the Pendo Logo start up screen, and then press On/Off Switch (Power) twice right away.
2. Factory mode menu comes out after 10 seconds, two fingers touches panel together to move to select the one like the following picture shows (no need to understand the Chinese words, just follow through as what the picture shows)
3. Press On/Off Switch (Power) and the following picture below will show, press On/Off Switch (Power) again to proceed on Recovery Mode, and wait for system to restart.
Unfortunately, nothing still happens.
ADB will not reveal what device it is, nor will Win 10 recognise the device for it to show in Device Manager or connected devices.
Windows responds with a ding ding, but nothing shows up.
I am stuck, and any info gladly accepted.
Thanks
Click to expand...
Click to collapse
not working in my pendotab window 8
Hi,
I could get no further with mine, the same as you.
I contacted Pendo Support, and explained it would work but not boot, I even asked for the image file so I could reload it in recovery mode, however, they did not have access to it, the Chinese manufacturer had not made it available to them.
As I described it was not damaged, but simply not working, they agreed to send me a replacement, even though it was out of warranty, as really, as I said to them, it was not fit for purpose.
I had to send the old one back, but they sent me a satchel in which to do so, at no cost to me.
They sent me the new one very promptly.
Hope is not lost,
Someone has finally manage to extract the factory ROM for the pendo PNDPP44QC7. Just search the model number on needrom.
phoenixemer.blogspot.com.au/2017/04/pendo-pad7-pndpp44qc7.html
password : emerlitspendotab7
TWRP custom recovery
drive.google.com/open?id=0B3k_2dFOmDBGRmljV3JuSUZiUkU
I tried to upgrade a similar device to 5.x, some changes, but some options now not working I have a clone Q88H device, A33 quadcore processor 7" clone. Kernel 3.4.39, firm ware 2.1 Need to go back to 4.4.2 w latest update. Hopefully Play store will work again, as I need it. That, or change to windows version. advice pls?
drusid said:
Hope is not lost,
Someone has finally manage to extract the factory ROM for the pendo PNDPP44QC7. Just search the model number on needrom.
phoenixemer.blogspot.com.au/2017/04/pendo-pad7-pndpp44qc7.html
password : emerlitspendotab7
TWRP custom recovery
drive.google.com/open?id=0B3k_2dFOmDBGRmljV3JuSUZiUkU
Click to expand...
Click to collapse
Please i dont have a needrom account i cant download plz who Can send me the direct link to m'y account
Hello and thank you for anyone bothering to read this.
I got a CAT S50 and was experiencing a bit of instability lately.
I've run LTE_S0201121.0_S50_0.023.00 without a hitch for a while, then it decided to crash several applications, from google play to any other app open.
That's when I decided to do a factory reset and see if it would help. Performed the rest without a hitch, but the errors kept coming back. At one point, the screen went black. I knew the phone was on because the backlit was working. I hard-reseted it (hold the power button for 30 seconds or more) and rebooted. The phone froze on the CAT splash logo screen and that's when I hard-reset it again. But when I tried to turn it on, the phone simply refused to work. No vibrate, sounds or anything. It's dead.
When I plug it on the computer's USB, the PC makes a sound as if it detected the device, but when I go to the device manager, I get this QHSUSB_BULK with the yellow exclamation mark
I want to know if it is possible to unbrick this phone and if so, if there is a tutorial or if someone can direct me to the correct procedure. I looked everywhere for the ftf file for this phone to attempt this with flashtool, but I simply can't find it.
ANY help of any form is greatly appreciated.
Sadly I had the same thing happen to me, just a black screen. It decided to delete recovery mode or I just cant get to it.
Power Off the Phone,
While pressing Press Vol Down + Cam Button insert a Powersource -- hold down Vol Down + Cam
Recoverymenu should start
Then flash the original rom via ADB Sideload or SD Card.
btw. i have flashed the LTE_S0201121.0_S50_0.023.00 but i want test older ROMs!
can anyone link or upload an older ROM ?
Guy i have the same issue, can you please help me
I got the same problem I search lots place but still nothing then normal update rom anyone can help?
Hi ,
So I got a pendopad 7 from dodo car insurance promotion and while I was trying to remove kingroot and replace with supersu , I think something went wrong and now tablet is in a weird state. It boots up to show nothing but if press and hold power button I can see option to turn off the tablet. I am assuming its something to do with systemui.apk , I was wondering if there is a way to fix it without rom install as I dont have any backup or the image to restore this tablet.
Its A-33 Quadcore Pendopad 7 PNDP51M7BLK
Ram 1 gb
Android 5.1.1
1024 x 600 px
http://www.pendo.com.au/pendopad-7-q...k-pndp51m7blk/
If anyone has this tablet or rom or any method to bring it back to life. Any help is appreciated.
I can acces the normal recovery on the tablet and have tried resetting it but doesnt help .I cant find the factory image for this device
Thanks
any help please ????????????
max414 said:
any help please ????????????
Click to expand...
Click to collapse
You may need more knowledge about this but here is what you can do
DON'T PLUG IN THE DEVICE INTO THE PC YET
Install Phoenix Suit and click the firmware button
Find a firmware image for your tablet. (most likely at chinagadgetsreviews.blogspot.com )
Hold down the power button for 10 seconds and let the tablet sit for 10-20 seconds to insure it is completely off.
ON THE DEVICE:
1: Hold ANY button that is not the power button
2: while still holding the other button, plug in the device to the computer
KEEP HOLDING IT DOWN
3: RIGHT after you plugged the microusb press the power button really quickly around 4 or 8 times and on the computer Phoenix Suite will ask you this:
Tip: Does Mandatory Format?
Click Yes
Click Yes again
It will install the new firmware, if it shows no progress for more than 6 minutes you don't have the right firmware image.
HOPE THIS HELPS
Oh yeah, you will need to re-root the device with KingoRoot PC, and Wifi, or Bluetooth may not work anymore. Sorry about that.