Related
So I bought this cheap tablet off of ebay and after about a week I connected it into the charger and forgot to unplug it.. Only next morning I saw and when I disconnected it it had turned off. So I turned it on and it was stuck in the newsmy logo and wasn't booting up.
There was nothing on the internet, but somehow I got it working again and for everybody's sake I'm posting what I did here.
First off, even though there are some references that this has allwinner A10 inside, ITS NOT. you will brick this if you flash an allwinner variant kernal.
If you are one of those brave souls who flashed on a allwinner kernals and bricked the thing, you would not be able to go to download mode even. Here is the steps to flash a fresh rom that would resolve most of issues:
1. Download driver pack from the attachment of this post
2. Download RKBatchTool here: http://www.x-drivers.com/catalog/fl...s_electronics/models/rk_batch_tool/27576.html..
3. Now turn off your tablet. If it doesn't turn off press a needle head into the reset pinhole and hold it for 5 seconds
4. Open device manager from your computer
5. Then hold the power on button and volume up(that is the one closer to power button) until it turns on. It'll boot your tab in download mode. After the green robot icon appears connect it to the computer by carefully monitoring device manager of computer
*** If you have flashed an allwinner or other rockchip kernal based ROM earlier and do not go in to download mode or no new device installation in your PC there's a real possibility your download mode combination may have changed. Turn it off by pressing needle to reset pinhole. Then turn off and connect it to PC. Then turn it on and then while in boot screen hold volume up. if not try similar procedure by holding volume down or back buttons. If you see driver installation in the PC and nothing in the tablets screen, thats fine. You can continue with the flasing
6. The driver installation probably will fail. Identify which device that is newly added to the device manager.
7. Right click on the device -> Update Driver. Then manually select -> Have disk then give rockusb file from drivers you just downloaded(if your system is 64-bits use files in amd-64 folder)
8. Then select RK29 as the device and update the driver
9. Now extract and run RKBatchTool and you must see under connected devices button #1 highlighted in green
10. Download official ROM here: http://220.168.57.227:1949/cunchu/20120312T3youhuaruanj.rar
There are other ROMs for T3 here as well. But this is the only thing that works
11. Extract it and give its update.img file path to RKBatchTool FW Path
12. Hit Restore
13. Wait few minutes for flash to complete
14. Then the tab will restart once or twice and will start booting up. This process should take maybe 5 minutes or more. Be patient
15. Then it'll finally boot.
I will post a Jelly Bean ROM for this tab here as soon as I cook one
Comments are much appreciated
Thank you! Thank you! Thank you!
Was searching for a guide to get my brothers Newsmy Newpad T3 up and running.
Thank you for this guide. will definitely try it out and leave a feedback.
P.S. Jellybean sounds interesting.
OK. After spending two days I finally got it to detect the Newsmy Newpad T3.
I had to install Android SDK for the USB drivers. (Don't know if it detected from that.)
Then downloaded super one click root. Found the android drivers in it, and when it asked which driver you want to install I gave "Android Composite" not sure but something in those lines.
Successfully rooted it.
Then off the tab and connect the USB cable, press power and volume up (one that is near the power) and when the tab boots
If it asked for drivers please do same as above
Now run the firmware installer provided inside the update.img folder that you downloaded from the original post by suki300me step 10. It is in Chinese and the first option is to change it to English found on the bottom screen.
If everything is set your tab will be in a black screen only thing you know is that it is on is the sound windows 7 makes when the phone is connected to it. Choose the udate .img file and press upgrade.
It will run up to 3-4 stages and will say data copy error. Remove the cable and press power, it will star installing ICS give it few minutes and you are done.
It took me many attempts so don't give up if it didn't work on your first try. Hope this helps someone.
Boot
Hi
I get one newsmy t3 tablet from my friend. The only problem the system is never loaded (stuck at the boot). I try the power+volume up but just the black screen appaers. Btw only turns on when its plugged. Please give me some tips.
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
[UPDATE] 2/22/2013 11:00pm gmt
I'm able to boot it only if I have it plugged in. I can only use Power + Volume controllers + Reset buttons. I can enter Recovery Mode but I cannot confirm/click on any selection.
Tablet does not get recognized by the computer in "Flashing Mode".
I forced to install the driver for the "Flashing mode" when the tablet is in recovery mode but programs like MSIFlashtool, RKBatchTool, RKAdnroid. (not sure if i correcly used the last 2... but whatever)
spilot said:
I've got an MSI Windpad Enjoy 10" Plus (http://www.msi.com/product/windpad/Enjoy-10-Plus.html) and I tried to flash it this ROM (http://forum.xda-developers.com/showthread.php?t=1540616).
The rom is for MSI Windpad Enjoy 10", while mine is called Enjoy 10" Plus. So GG, I think I got owned. So retarded you don't even have to tell me.
Now whenever I try to turn on the tablet, it would simply vibrate, show the logo and then turns off. PC doesn't detect it.
However, I tried holding Power button + Reset button together, the PC detects it, but it's unknown and it can't identify it (even though I have MSI's drivers installed and all).
...Any ideas on how to overcome it?
I'm going to sleep now, and will check tomorrow. Thanks in advance.
Click to expand...
Click to collapse
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Jack Jake said:
i dont think that that is called brick
anyways go download Odin and the stock image for your phone (in tar format)(just search on XDA)
put phone into download mode nd open odin
select PDA and select the tar file u downloaded
click start and it should take u back to stock
forgot if this unroots ur phone or not so u might have to root again.
Click to expand...
Click to collapse
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Sent from my ARCHOS 80G9 using Tapatalk HD
Quinny899 said:
This is not Samsung or a phone. Read what you are told
If you have a splash screen, you are not bricked. Does adb recognise your tablet? Can you access any recovery/download mode?
Click to expand...
Click to collapse
ADB doesn't recognize it. I tried holding Power + Reset button and did 'adb devices' on Ubuntu and it didn't show anything. On Windows, if I held these 2 buttons, it would show an unknown device in Device Manager. (Mind you, I don't have the Android SDK on Windows, just Linux.)
I can't access any recovery/download mode. Any combination of buttons (Power+VolDown, Power+VolUp/VolDown, Power+VolUP, Power+Home, Power+Back, Power+Settings) would do nothing.
-----------------------------------------------------------------------------------------------------
This what it does when I press Power + Reset Button with a needle. It boots up, splash screen, and stays on black screen (Btw, in this stage, it's Unknown Device in Windows Manager).Once I let go of Reset or Power button, it shuts down.
Turning it on without holding Reset, it would show splash screen, black screen and turns off in about 2 seconds.
Bump.
I've tried playing with it for some time. I can't get it to stay working without pressing power+reset buttons, it always shuts off...
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Sent from my Enjoy 10 Plus using xda app-developers app
mramzi said:
Go to the device website, and download section, get the latest firmware and forget to download the flash driver.
Follow the steps that in firmware folder after unzip it, and you'll get your tablet on
Click to expand...
Click to collapse
... I was trying all the time to get it work on the PC without plugging the charger. Anyways~
(Tablet's turned off), I plugged charger, I plugged USB, I turned on the tablet and viola it actually worked and booted into OS. However, no buttons work AT ALL, and touch input doesn't work as well.
I tried to get into Recovery Mode and it worked, but I can go up/down using VolUp/VolDow buttons but I cannot click on any thing because the home button don't work nor any other.
Only Power + VolUp + VolDown + Reset buttons work... What to do now?
TL;DR I want to click on 'Update from SD Card' from the Android Recovery but I couldn't get the 'home' button to click enter on the selection. So what's the solution?
bump.
updates:
I tried to place the firmware from the official website as update.img on an SD Card and placed it in the tablet and went into the recovery mode and selected the 'update from sd card' but i couldn't click it. I tried to tap power, home, search, settings and back and nothing worked.
what I've got up until now:
I can boot into the ROM / RecoveryMod as long as I have the charger plugged in the tablet.
For Ubuntu, when I use the command $ tail -f /var/log/syslog and plug in my tablet, it shows this log http://pastebin.com/pBpBUA2Q (it identifies the tablet) [note, the tablet is booted into the ROM]
Also, if I'm in the recovery mode and I plug in the tablet, it would enumerate the USB... ~,~
Bump
bump
spilot said:
bump
Click to expand...
Click to collapse
Please don't bump your thread more than once in 24 hours, it's against the rules
Sent from my Galaxy Nexus using Tapatalk HD
bump
Hello,
I know it has been long since this thread stopped.
I'm currently in his shoes and for the life of me cannot find anything on the web to help me solve my problem.
My MSI Enjoy 10" Plus was flashed with the wrong MSI Enjoy 10" update. Now the tablet only turns on when in "Recovery Mode", but selecting in that mode is not possible using 10" Plus' buttons. Is there anyone from you good people that can help? Please? Thanks.
Uhm...bump?
Bump? Need help from the experts here. Please. I'm desperate.
Thank you very much in advance.
Hello, i've been trying to find anything related to this tablet, a Hipstreet Equinox 10.1 HS-10 DTB1-4GB, from what i can tell its supposed to be based on android 2.3 gingerbread.
The tablet basically trefuses to boot up and i've been trying to find a way to get into recovery to do a factory reset or a firmware to force flash to factory reset but i have been unable to find out how to do either, or even any information/firmwares for this tablet. if anyone can help me it would be greatly apreciated.
dragonfly14 said:
Hello, i've been trying to find anything related to this tablet, a Hipstreet Equinox 10.1 HS-10 DTB1-4GB, from what i can tell its supposed to be based on android 2.3 gingerbread.
The tablet basically trefuses to boot up and i've been trying to find a way to get into recovery to do a factory reset or a firmware to force flash to factory reset but i have been unable to find out how to do either, or even any information/firmwares for this tablet. if anyone can help me it would be greatly apreciated.
Click to expand...
Click to collapse
Your tablet may not have CWM or TWRP recoveries..Some combinations you can try are:
When tablet is booting up press VOLUP or VOLDOWN or both.
When tablet is booting up press VOLUM + Power or VOLDOWN + Power or both.
UltraWelfare said:
Your tablet may not have CWM or TWRP recoveries..Some combinations you can try are:
When tablet is booting up press VOLUP or VOLDOWN or both.
When tablet is booting up press VOLUM + Power or VOLDOWN + Power or both.
Click to expand...
Click to collapse
its most definitely on stock recovery for GB 2.3, but i have not managed to get into it. i have Vol + vol - Menu, home and back buttons, so far i've tried volume +/- both + power and ive tried menu + power as well as back and the home individually. i have not managed to get anything different other than on home + power, when i do that, i ttakes 5x longer on the "hipstreet splash logo" once it gets past that though it says android then infiniblackscreen. - i dont get anything on a host computer via the USB either when trying any of these combos - hoping to get ADB to do a factory reset via ADB.
i used to have a ployer momo 9 and i remember that tablet had a special recovery mode with a special flasher and was wondering if something like that existed for this cheap tablet which is based on just about the same thing, allwinner dual core 1.0 ghz + 512mb ram + 4 gb rom.
dragonfly14 said:
its most definitely on stock recovery for GB 2.3, but i have not managed to get into it. i have Vol + vol - Menu, home and back buttons, so far i've tried volume +/- both + power and ive tried menu + power as well as back and the home individually. i have not managed to get anything different other than on home + power, when i do that, i ttakes 5x longer on the "hipstreet splash logo" once it gets past that though it says android then infiniblackscreen. - i dont get anything on a host computer via the USB either when trying any of these combos - hoping to get ADB to do a factory reset via ADB.
i used to have a ployer momo 9 and i remember that tablet had a special recovery mode with a special flasher and was wondering if something like that existed for this cheap tablet which is based on just about the same thing, allwinner dual core 1.0 ghz + 512mb ram + 4 gb rom.
Click to expand...
Click to collapse
Using ADB is a good idea .I didn't think of that though :silly:...
UltraWelfare said:
Using ADB is a good idea .I didn't think of that though :silly:...
Click to expand...
Click to collapse
thanks, but yeah, i cant get anything out of it so far and was hoping someone had the magical way to revive it :/ i believe on my ployer it was something ridiculous like vol - + home + back + power for 5 seconds and i had to get it flashing within 5 seconds of that or it would switch modes.... x_x
dragonfly14 said:
thanks, but yeah, i cant get anything out of it so far and was hoping someone had the magical way to revive it :/ i believe on my ployer it was something ridiculous like vol - + home + back + power for 5 seconds and i had to get it flashing within 5 seconds of that or it would switch modes.... x_x
Click to expand...
Click to collapse
Wait I found something for you
There is a few tricks to get your Tablet back , You require a few things
-A usb cable to connect to computer
-Internet connectivity
Now Lets start by putting the tablet in Android recover mode .
1. Connect the tablet to the USB port on the Computer .
2. Press and hold the power button and the Big button on the tablet , Keep pressing it until the logo of the android gut with his gut open shows up .
3. It is possible to perform a reset using the ADB (Android Debug Bridge)
I did mine on Windows XP , (Does your tablet install correctly in the Device manager? )
If so That is great news , You may goto step 5
If not Goto step 4 :
Step 4: Getting the Chinese driver equivalent for your tablet .
Get the drivers for the Ainol 7" Auror tablet (or equivalent )
Now Before the driver will work with your device (you can try to install it but it will give you an INF error)
You must edit the file (.INF) to match your USB id of the tablet
(At the bottom of the file change the STRINGS section to the device codes of your tablet ) (found by right clicking the Unknown device in the device manager . the (VID_1f3a_PID_efe8) is the HARDWARE ID and the
[Strings]
USBDRV="USB Devices"
USB\VID_1f3a&PID_efe8.DeviceDesc="USBDevice(VID_1f3a_PID_efe8)"
YOUR STRINGS:
USBDRV="USB Devices"
USB\<YOURDEVICEID>.DeviceDesc=USBDevice(<YOURDEVICEID>)"
Step 5:
Get the Recovery tool from here
https://spideroak.com/share/KNQW243.../CWM_Recovery_Manta_MID08_windows_install.zip
This will give you a suite of tools to restore your device to factory reset
Use it to install the recovery partition , and then reboot your device in recovery mode , Then use the Vol + and - buttons to navigate and power button to Enter .
(Source : click here)
Hello there, i have a Hipstreet too, but my android have crashed and dont turn on anymore.
I cant find the stock rom or custom rom anywhere.
Can you find some of these?
If you dont, you can make a backup and send a link to me?
Thanks and sorry for the english.
Hi,
my Pipo M6 per wifi hangs itself while starting, i.e. he gets stuck with the loading picture. Indeed, with the Reset he restarts, however, gets stuck also again. After he gets stuck, he can be also switched off no more, except by Reset.
And I also do not come to the Recovery mode, I thought, maybe helps a new firmware. However, sometimes he registers if I hold the keys while starting low-spirited, that Android little manes with open belly and warning sign. see below.
If I hang him by USB on my Win7 pc, a wrong driver's file is installed constantly, either Samsung or HTC, so that the Flashtools register that no suitable device is connected. With the USB driver of Pipo the pc says that that is no suitable driver's file.
What can I do?
And over again for stupid ones: I come to the Recovery fashion, nevertheless, dur volume press ESC and power at the same time, or?
Please, can anybody help me?
Nobody can help?
Is the tablet an fall for garantie?
Anybody any idea?
Please help.
Try one of the 2 methodes
gnom68 said:
Is the tablet an fall for garantie?
Anybody any idea?
Please help.
Click to expand...
Click to collapse
A This is the easiest way: Do a HARDRESET
Recovery Mode (for Factory Reset):
-----------------------------------------------------------
1. [Reset] (on the backside)
2. [Power] + [Vol-]
3. green Android shows up
4. press [Vol-] + [Vol+] + [ESC] together till Menu shows up (if it's not showing up try to press it a few once more)
OR
B For advanced users: Flash the original Firmware (download from here it is a very slow download )
and use the howto which is delivered within the downoad.
Maybe you can find some usefull information here
Hope i could help u. For me it was working fine.....
{Solved}I have an Azpen A727 i bought from MicroCenter that I bricked.
I found out the solution to unbrick the tablet. First you need the firmware for the version of Android your A727 came with (Jelly Bean or KitKat) which i will provide the links for or you can request from Azpen (which i did and got a response for in 30min), 2nd you need a flashing tool called PheonixUSBPro and a "key" to flash your firmware on the bricked tablet.
1. Follow the instructions on this page for flashing firmware and downloading PhoenixUSBPro here http://www.azpenpc.com/download/detail.php/id-2.html or use the Backup here https://drive.google.com/folderview...JrLUZEYTFjOVF2ajJISy1pdkVCSTgzVlk&usp=sharing
2. a. Firmware and "Key" for A727 Jelly Bean https://drive.google.com/folderview?id=0B53yZ1fbVqxJVnNFSkY2cjFoRjQ&usp=sharing
b. Firmware and "Key" for A727 KitKat (For some reason we have two different versions. If one doesn't work try the other)https://drive.google.com/folderview?id=0B53yZ1fbVqxJZGx2SDVPcWhsWmM&usp=sharing
Note: If anyone is having trouble with PhoenixUSBPro detecting your tablet try holding down the power button and plugging in your tablet from the micro-USB side then press the power button 10 times. Then Windows should be installing the driver so PhoenixUSBPro should detect it now. It worked for me in Windows 7.
If anyone has any problems let me know . Thank you @viper2110 for providing the community with the KitKat firmware.
bricked as well
Were you able to get the device working again?
I bricked mine messing with it today and am trying to fix it.
Have the stock recovery so far if you still need it let me know. xda wont let me attach for some reason
buellonsholes said:
Were you able to get the device working again?
I bricked mine messing with it today and am trying to fix it.
Have the stock recovery so far if you still need it let me know. xda wont let me attach for some reason
Click to expand...
Click to collapse
Yep i fixed it. I edited the first post with the solution
thank you
treecheetahdolo said:
Yep i fixed it. I edited the first post with the solution
Click to expand...
Click to collapse
still trying to figure out adb, livesuit, and eclipse all at once but here we go.
nothing like jumping in and just figuring out whats what lol
no luck
treecheetahdolo said:
{Solved}I have an Azpen A727 i bought from MicroCenter that the camera wasnt working so i decided to install a custom ROM on it instead of bringing back to the store. I was able to root it. But once I flashed a custom ClockWorldMod from http://forum.xda-developers.com/showthread.php?t=2532464 i was bricked.
I found out the solution to unbrick the tablet. First you need the firmware which i will provide the link for or you can request from Azpen (which i did and got a response for in 30min), 2nd you need a flashing tool called PheonixUSBPro and a "key" to flash your firmware on the bricked tablet.
1. Follow the instructions on this page for flashing firmware and downloading PhoenixUSBPro http://www.azpenpc.com/download/detail.php/id-2.html
2. Firmware and "Key" https://drive.google.com/folderview?id=0B53yZ1fbVqxJVnNFSkY2cjFoRjQ&usp=sharing
If anyone has any problems let me know
.
Click to expand...
Click to collapse
Can 't figure out why but after trying many times phoenixpro fails me (trying to use key but red button and green button both arent there)
livesuit wont run either unsure why
only thing i have up and running is sdk manager and im working on learning the steps with it
anyone who can help it would be appreciated. using a windows 8
Very important:
Originally Posted by dsulliii View Post
1) Make sure your A700 is turned off. (Do NOT have the micro-USB end plugged into your A700 at this time, that is for later.)
2) Start LiveSuit on your computer. (The COMPUTER end of your USB cable should be plugged into ONLY your computer at this stage.)
3) Select the ROM that you want to flash to your A700.
4) Hold down the Vol button on your device (I usually hold it down Vol-, not Vol+, but I believe that this device does not matter which.)
5) While holding down Vol, plug the micro-USB end of the cable into your A700. Keep holding down the Vol button.
6) While still holding down the Vol button, WITH the USB cable now connected between your computer and your A700, press and release the A700's Power button 10 times, and wait for a second to a few.
7) The LiveSuit program will detect your A700 going into download mode and begin prompting you for what to do.
8) Follow LiveSuit's recommendations, including formatting. It will take less than 5 minutes.
This wasn't clear to me from the original post.
However I followed the original link and figured it out.
Hope that clears it up for anyone else.
.....
WarezAppz said:
Very important:
Originally Posted by dsulliii View Post
1) Make sure your A700 is turned off. (Do NOT have the micro-USB end plugged into your A700 at this time, that is for later.)
2) Start LiveSuit on your computer. (The COMPUTER end of your USB cable should be plugged into ONLY your computer at this stage.)
3) Select the ROM that you want to flash to your A700.
4) Hold down the Vol button on your device (I usually hold it down Vol-, not Vol+, but I believe that this device does not matter which.)
5) While holding down Vol, plug the micro-USB end of the cable into your A700. Keep holding down the Vol button.
6) While still holding down the Vol button, WITH the USB cable now connected between your computer and your A700, press and release the A700's Power button 10 times, and wait for a second to a few.
7) The LiveSuit program will detect your A700 going into download mode and begin prompting you for what to do.
8) Follow LiveSuit's recommendations, including formatting. It will take less than 5 minutes.
This wasn't clear to me from the original post.
However I followed the original link and figured it out.
Hope that clears it up for anyone else.
Click to expand...
Click to collapse
i'm feeling really dumb here i read that too and am pretty sure i have gotten it into this mode. but its the livesuit software thats the problem i cant get that or the other ones i mentioned to even run. anything i do get to run (phoenix and sdk) dont seem to run correctly. windows 8 is annoying me this week. im trying to get one of my old windows 7 computers up and running and ill try again i guess
WarezAppz said:
Very important:
Originally Posted by dsulliii View Post
1) Make sure your A700 is turned off. (Do NOT have the micro-USB end plugged into your A700 at this time, that is for later.)
2) Start LiveSuit on your computer. (The COMPUTER end of your USB cable should be plugged into ONLY your computer at this stage.)
3) Select the ROM that you want to flash to your A700.
4) Hold down the Vol button on your device (I usually hold it down Vol-, not Vol+, but I believe that this device does not matter which.)
5) While holding down Vol, plug the micro-USB end of the cable into your A700. Keep holding down the Vol button.
6) While still holding down the Vol button, WITH the USB cable now connected between your computer and your A700, press and release the A700's Power button 10 times, and wait for a second to a few.
7) The LiveSuit program will detect your A700 going into download mode and begin prompting you for what to do.
8) Follow LiveSuit's recommendations, including formatting. It will take less than 5 minutes.
This wasn't clear to me from the original post.
However I followed the original link and figured it out.
Hope that clears it up for anyone else.
Click to expand...
Click to collapse
Im pretty sure LiveSuit wont work on the A727 because the CPU is different. The A727 uses an Allwinner thats why we have to use PhoenixUSBPro. Sorry for my late response I dont have internet anymore so I got lucky today getting online, lol.
treecheetahdolo said:
Im pretty sure LiveSuit wont work on the A727 because the CPU is different. The A727 uses an Allwinner thats why we have to use PhoenixUSBPro. Sorry for my late response I dont have internet anymore so I got lucky today getting online, lol.
Click to expand...
Click to collapse
Yeah, sorry I was using PhoenixUSBPro, guilty of not mentioning that.
Anyone else have any luck unbricking the A727 with this method?
Look what I ran across
SDK for Allwinner CPUs?
Now will this aid in someone creating a Android 4.4 image for an Azpen a1023 or at least a custom CWM or TWRP? for one?
answer soon back.
WarezAppz said:
SDK for Allwinner CPUs?
Now will this aid in someone creating a Android 4.4 image for an Azpen a1023 or at least a custom CWM or TWRP? for one?
answer soon back.
Click to expand...
Click to collapse
I dont know but BLuFeNiX started this thread where he did a CWM for an A700 http://forum.xda-developers.com/showthread.php?t=2532464
treecheetahdolo said:
I dont know but BLuFeNiX started this thread where he did a CWM for an A700 http://forum.xda-developers.com/showthread.php?t=2532464
Click to expand...
Click to collapse
Yeah I was aware of that, but that's for an A700
and I am actually interested in A1023, not sure the A700 will work for the A1023
Question. Frozen after reimage.
Hi all! I was able to reimage my A727 with PhoenixUSBPro and the firmware and key linked in the OP, but when it reboots and comes up to the initial screen, it's frozen. Won't take any input. The only thing I can do is force a shutdown with the power button. Am I doing something wrong? Thanks.
TMBackstrom said:
Hi all! I was able to reimage my A727 with PhoenixUSBPro and the firmware and key linked in the OP, but when it reboots and comes up to the initial screen, it's frozen. Won't take any input. The only thing I can do is force a shutdown with the power button. Am I doing something wrong? Thanks.
Click to expand...
Click to collapse
I dont know. Have you tried pressing the reset button?
treecheetahdolo said:
I dont know. Have you tried pressing the reset button?
Click to expand...
Click to collapse
Yup, tried the reset button and resetting back to factory. Still frozen.
I just redownloaded everything from the OP onto a Win 7 Pro x86, instead of on my Win 7 Ultimate x64 system, ran the upload, and it is working fine now. Thanks for all the help. :good:
TMBackstrom said:
I just redownloaded everything from the OP onto a Win 7 Pro x86, instead of on my Win 7 Ultimate x64 system, ran the upload, and it is working fine now. Thanks for all the help. :good:
Click to expand...
Click to collapse
Wow interesting. Im surprised it made a difference. Im glad you have everything up and running now
treecheetahdolo said:
{Solved}I have an Azpen A727 i bought from MicroCenter that I bricked.
I found out the solution to unbrick the tablet. First you need the firmware which i will provide the link for or you can request from Azpen (which i did and got a response for in 30min), 2nd you need a flashing tool called PheonixUSBPro and a "key" to flash your firmware on the bricked tablet.
1. Follow the instructions on this page for flashing firmware and downloading PhoenixUSBPro
2. Firmware and "Key"
If anyone has any problems let me know
Click to expand...
Click to collapse
I also have an azpen tablet that comes up with the azpen logo when switching it on and it just stays there.
I did try your solution above but does not work. The device does not seem to be picked up in PhoenixUSBPro.
In windows device manager it did pick up the device as "USB Developer". I instlled the Google drives and now it shows as "Android Composite ADB Interface". But PhoenixUSBPro still does nit pick it up.
Any ideas what else I can try.
viper2110 said:
I also have an azpen tablet that comes up with the azpen logo when switching it on and it just stays there.
I did try your solution above but does not work. The device does not seem to be picked up in PhoenixUSBPro.
In windows device manager it did pick up the device as "USB Developer". I instlled the Google drives and now it shows as "Android Composite ADB Interface". But PhoenixUSBPro still does nit pick it up.
Any ideas what else I can try.
Click to expand...
Click to collapse
Are you holding down the power button and volume down button while plugging in your tablet like Azpen said?