Has anybody found a link to any custom or stock firmware for this tablet?
I have a small annoying issue that I am sure could be fixed with a flash, the back button randomly stops working until I reboot.
The baby Einstein on their 800 number thought a factory reset would fix it, then that using the software button was a good enough solution and had no clue about tablets in general. Through Support e-mail they were heading towards wanting me to ship the tablet back rather than supply a link to firmware. I explained to them it doesn't appear to be hardware related as it is random, and reboot fixes it.
im looking for the same firmware man, i have mine bricked :S
How to Flash Zeki TB782B, TB1082B Rom with Livesuit (UnBrick)
gmrastaman said:
im looking for the same firmware man, i have mine bricked :S
Click to expand...
Click to collapse
There is already a different thread on here with the information, but here is how I have personally done it......
Zeki TB782B/TB1082B is using the Allwinner Chip A10.
I search in the web and found the Rom flash steps
Flash Tool LivesuitPack
http://hotfile.com/dl/136803097/cffe...ivers.rar.html
The flash ROM Demo video
http://www.youtube.com/watch?v=238RR-WvhrQ
You can get the Rom at below link
http://depositfiles.com/files/u7ew46yzm
FID HN TB1082B ROM
http://depositfiles.com/files/ay9hhvpyf
FID CF TB782B ROM
http://depositfiles.com/files/0wopipacg
FID BN TB1082B ROM
http://depositfiles.com/files/4uoxkwjc4
FIB BN TB782B ROM
1.Required files: Upgrade tool (Livesuit.exe)
2. Make sure your tablet is fully charged
3. Backup your data, device will be formatted during upgrade
4. The driver and upgrade software work for both Windows XP and Windows 7.
Upgrade Steps:
1. Unzip the upgrade tool and USB drive to your hard drive (recommend to put it in C:\ ).
Double-click the LiveSuitPack_v1.07.exe file, it will automatically install the driver files. Click “OK” to complete the driver installation.
2. Open Livesuit.exe
Double-click to open the upgrade tool LiveSuit.exe
3. Select the firmware
Click “No” to not choose the user upgrade wizard, and click the “Select Firmware” button (the first button from the left) to select the firmware .img file.
4. Turn off your tablet
Make sure the tablet is powered off (Turn it on, press the power button for more than 8 seconds to force power off)
5. Press the key combination to start it in the upgrade mode
a. Press and hold down the “Vol +”, button on TB782B,TB892B or “Home” button on TB1082B
b. Connect the USB cable to tablet and computer
c. After connecting the USB cable, press the power button 6 times quickly (you should get a popup window if done correctly, if not repeat step 5 from beginning)
d. DON’T release the “Vol+” button till the LiveSuit window pops up
e. You can now release the “Vol+” button
(Note: If you install the driver at this time the pop-up dialog box, the path to point to installation directory UsbDriver Livesuit folder, click Next to complete the driver installation prompts).
You should see Livesuit window pops up; otherwise, you didn’t do it correctly, you have to repeat step 4 and 5.
6. Select the format to force upgrade
Livesuit prompt “force format”, click “Yes” (Y). All of the original apps installed will be removed.
We highly recommend mandatory format! ! ! Otherwise the update is not complete and may brick! ! !
7. Upgrade begins
Pop-up “OK to force format” dialog box, select “Yes”, the upgrade begins:
8. The upgrade is complete
Firmware download process lasted about three and a half minutes or so, please wait until the prompt “upgrade successful.”
9. Automatic restart
After the upgrade is complete, your tablet will automatically restart, then you can unplug the USB cable.
Slow start-up time machine for the first time, please be patient.
If the machine does not restart automatically, press and hold the Power button for 8-10 seconds or more to ensure the power switch off, then press the Power button 3 seconds or more to turn on your tablet.
10. Congratulations! You have flashed the firmware.
you can get the Google Play at below link
http://forum.xda-developers.com/show....php?t=1621831
ROM for Zeki TB753b
Do you happen to have the Rom for the TB753b (JB 4.1.1)? I have soft bricked my mom's tablet, and need the rom so I can flash it, and hopefully get her tablet back in working order.
Zeki TBD753B stock rom
I am generally good at finding stuff, but I too can not find the stock rom for the tbd753b 7" zeki tab. Any help would be much appreciated. Thank You
need build.prop
i need the original build.prop to flash to my messed up TB753B. does anyone got it??!!??
dragonfriend0013 said:
i need the original build.prop to flash to my messed up TB753B. does anyone got it??!!??
Click to expand...
Click to collapse
Do you still need the build.prop.original?
Sent from my TBD753B using Tapatalk 4
Got it working
vindicato said:
Do you still need the build.prop.original?
Sent from my TBD753B using Tapatalk 4
Click to expand...
Click to collapse
I was finally able to get access to it through ADB and reset the permissions on the file. all is good now. I do still have problems with the screen "double tapping" though and have not figured out how to fix it. Does yours do the same thing.
The only problem I seem to have is that top left hand corner. Sometimes you have to tap that location a couple of times if that's what you mean
Sent from my TBD753B using Tapatalk 4
---------- Post added at 06:42 PM ---------- Previous post was at 06:37 PM ----------
That and updating my Super su binary...
Sent from my TBD753B using Tapatalk 4
please give the firmware for tb753b
please give the firmware for tb753b. for Livesuit.exe
ROM for TAB ZEKI tbdc1093b
any have de rom for this tab? ZEKI tbdc1093b
fallen links , FID: BN TB782B
Can someone help me? I need this rom , my tablet is brick
Zeki TB782B/TB1082B is using the Allwinner Chip A10.
I search in the web and found the Rom flash steps
Flash Tool LivesuitPack
http://hotfile.com/dl/136803097/cffe...ivers.rar.html
The flash ROM Demo video
http://www.youtube.com/watch?v=238RR-WvhrQ
You can get the Rom at below link
http://depositfiles.com/files/u7ew46yzm
FID HN TB1082B ROM
http://depositfiles.com/files/ay9hhvpyf
FID CF TB782B ROM
http://depositfiles.com/files/0wopipacg
FID BN TB1082B ROM
http://depositfiles.com/files/4uoxkwjc4
FIB BN TB782B ROM
1.Required files: Upgrade tool (Livesuit.exe)
2. Make sure your tablet is fully charged
3. Backup your data, device will be formatted during upgrade
4. The driver and upgrade software work for both Windows XP and Windows 7.
Upgrade Steps:
1. Unzip the upgrade tool and USB drive to your hard drive (recommend to put it in C:\ ).
Double-click the LiveSuitPack_v1.07.exe file, it will automatically install the driver files. Click “OK” to complete the driver installation.
2. Open Livesuit.exe
Double-click to open the upgrade tool LiveSuit.exe
3. Select the firmware
Click “No” to not choose the user upgrade wizard, and click the “Select Firmware” button (the first button from the left) to select the firmware .img file.
4. Turn off your tablet
Make sure the tablet is powered off (Turn it on, press the power button for more than 8 seconds to force power off)
5. Press the key combination to start it in the upgrade mode
a. Press and hold down the “Vol +”, button on TB782B,TB892B or “Home” button on TB1082B
b. Connect the USB cable to tablet and computer
c. After connecting the USB cable, press the power button 6 times quickly (you should get a popup window if done correctly, if not repeat step 5 from beginning)
d. DON’T release the “Vol+” button till the LiveSuit window pops up
e. You can now release the “Vol+” button
(Note: If you install the driver at this time the pop-up dialog box, the path to point to installation directory UsbDriver Livesuit folder, click Next to complete the driver installation prompts).
You should see Livesuit window pops up; otherwise, you didn’t do it correctly, you have to repeat step 4 and 5.
6. Select the format to force upgrade
Livesuit prompt “force format”, click “Yes” (Y). All of the original apps installed will be removed.
We highly recommend mandatory format! ! ! Otherwise the update is not complete and may brick! ! !
7. Upgrade begins
Pop-up “OK to force format” dialog box, select “Yes”, the upgrade begins:
8. The upgrade is complete
Firmware download process lasted about three and a half minutes or so, please wait until the prompt “upgrade successful.”
9. Automatic restart
After the upgrade is complete, your tablet will automatically restart, then you can unplug the USB cable.
Slow start-up time machine for the first time, please be patient.
If the machine does not restart automatically, press and hold the Power button for 8-10 seconds or more to ensure the power switch off, then press the Power button 3 seconds or more to turn on your tablet.
10. Congratulations! You have flashed the firmware.
you can get the Google Play at below link
http://forum.xda-developers.com/show....php?t=1621831[/QUOTE]
Related
Can someone help me recover from a from a full format, i was trying to root and [email protected] up and did full format, it still boots archos recovery but i can get nowhere, help please!
Thanks
do this ----
Shano56 said:
Note: You WILL need a PC connected to the internet, and the USB cable that came with your device. Before you being, please download Archos 80/101 G9 OS v 4.0.4 (190733Kb, for 80/101 G9 devices only) to your PC, copy to your desktop or wherever you will remember, then do the following:
Step 1: Power off your device
Step 2: Hold the volume rocker down and press the power button simultaneously
Step 3: Once in recovery, select "Format System", then "Reformat Device..." (use the volume up/down to change selection, power button to select)
you already did this
Step 4: Once formatted, return to recovery using the same method above, this time select "Update Firmware"
Step 5: Plug your device into your computer using the USB cable that came with your device
Step 6: A new drive should appear in "My Computer", copy firmware_archos_it4.aos to this device
Step 7: Ensure the transfer is completed, then press the power button on your device, keep it plugged in while it is updating
Step 8: Your device should boot, and be updated to the latest firmware 4.0.4
Click to expand...
Click to collapse
Worked perfectly! U the man! Thank you very much!
Sent from my SCH-I500 using xda premium
If i help you, feel free to click the thanks button! glad u got everything working
I download this stock rom from this thread http://forum.xda-developers.com/showthread.php?t=1651794&page=2
Plz guide me how i flash this rom on my Galaxy Tab 10.1 Wifi P7510
There is only one file in the zip file with this name (P7510XEUKL2_P7510XXKL2_HOME.tar.md5) I select the PDA and push the start button, but very little progress bar shown on my tab then stopped, and not increase the progress for 1 hour. and the last message in the odin message box is "image.cache" then i reboot the tab and error comes "error occurred during boot" then i again start the tab by pressing the volume down + power button then it comes on the selection page for downloading mode and recovery mode. then i go to recovery and recover my backup.
now tell me which option I select, I mean, PDA, Bootloader, Phone or CSC.
yasirshafiq said:
I download this stock rom from this thread http://forum.xda-developers.com/showthread.php?t=1651794&page=2
Plz guide me how i flash this rom on my Galaxy Tab 10.1 Wifi P7510
There is only one file in the zip file with this name (P7510XEUKL2_P7510XXKL2_HOME.tar.md5) I select the PDA and push the start button, but very little progress bar shown on my tab then stopped, and not increase the progress for 1 hour. and the last message in the odin message box is "image.cache" then i reboot the tab and error comes "error occurred during boot" then i again start the tab by pressing the volume down + power button then it comes on the selection page for downloading mode and recovery mode. then i go to recovery and recover my backup.
now tell me which option I select, I mean, PDA, Bootloader, Phone or CSC.
Click to expand...
Click to collapse
Installation Guide
1) Make sure you have the drivers installed
2) Extract ur firmware it to get its content which would be a .tar
3) Download Odin3 v1.85. Then, extract it to get these two required files – Odin3 v1.85.exe and Odin3.ini. Do NOT delete the .ini file since it’s required too. When asked in step 6 below, open Odin by double clicking on the Odin3 v1.85.exe file.
4) Disconnect your tablet if it’s connected to PC. Power it off. Wait 5-6 seconds for vibration to confirm complete switch off.
5) Now, put the Galaxy Tab 10.1 tablet in Download Mode (also called Odin mode) — press and hold, until Samsung Galaxy logo appears — these keys together: Volume_DOWN + Power.
6) Wait till you a screen with options to boot into recovery or download (odin) mode.
7) Press Volume Up key to boot into download mode.
8) Open Odin (from step 3) — Odin3 v1.85.exe. Admin privileges would be required!
9) Connect your Galaxy tab 10.1 tablet to PC now. You should get the message “Added! !” under the Odin’s message box in the bottom left. And you should also see COM port with a number in Yellow. If you don’t get this message, then probably there is a problem with drivers. Make sure you’ve the right drivers installed!
10) Select these files in Odin at respective tabs.
11) Click the PDA Tab, and select the big .tar file “P7510XEUKL2_P7510XXKL2_HOME.tar.md5″
Important! Make sure these 2 check-boxes are selected: Auto Reboot and F. Reset Time. Also, leave the Re-Partition check-box clear (blank), as we are only using a .tar file or PDA file to flash.
12) Double check everything said in step 11.
13) Now, hit the START button to begin the flashing process. When it finishes, your tablet will automatically reboot — and you can unplug the cable when Galaxy logo appears. Plus, you’ll get a PASS (with green background) message in the left-most box at the very top of the Odin. If it’s red and with FAIL written over it, the process flashing process wasn’t successful, Try again, and take care to complete the whole process without any break whatsoever.
Hit Like If it helps..
How do you get the drivers that work when the Tab is booted to ODIN? I've tried everything I can find and have been unable to get the correct drivers installed.
akhil17kr said:
Installation Guide
1) Make sure you have the drivers installed
2) Extract ur firmware it to get its content which would be a .tar
3) Download Odin3 v1.85. Then, extract it to get these two required files – Odin3 v1.85.exe and Odin3.ini. Do NOT delete the .ini file since it’s required too. When asked in step 6 below, open Odin by double clicking on the Odin3 v1.85.exe file.
4) Disconnect your tablet if it’s connected to PC. Power it off. Wait 5-6 seconds for vibration to confirm complete switch off.
5) Now, put the Galaxy Tab 10.1 tablet in Download Mode (also called Odin mode) — press and hold, until Samsung Galaxy logo appears — these keys together: Volume_DOWN + Power.
6) Wait till you a screen with options to boot into recovery or download (odin) mode.
7) Press Volume Up key to boot into download mode.
8) Open Odin (from step 3) — Odin3 v1.85.exe. Admin privileges would be required!
9) Connect your Galaxy tab 10.1 tablet to PC now. You should get the message “Added! !” under the Odin’s message box in the bottom left. And you should also see COM port with a number in Yellow. If you don’t get this message, then probably there is a problem with drivers. Make sure you’ve the right drivers installed!
10) Select these files in Odin at respective tabs.
11) Click the PDA Tab, and select the big .tar file “P7510XEUKL2_P7510XXKL2_HOME.tar.md5″
Important! Make sure these 2 check-boxes are selected: Auto Reboot and F. Reset Time. Also, leave the Re-Partition check-box clear (blank), as we are only using a .tar file or PDA file to flash.
12) Double check everything said in step 11.
13) Now, hit the START button to begin the flashing process. When it finishes, your tablet will automatically reboot — and you can unplug the cable when Galaxy logo appears. Plus, you’ll get a PASS (with green background) message in the left-most box at the very top of the Odin. If it’s red and with FAIL written over it, the process flashing process wasn’t successful, Try again, and take care to complete the whole process without any break whatsoever.
Hit Like If it helps..
Click to expand...
Click to collapse
Thanks
@akhil17kr thanks for your help.
caseym said:
How do you get the drivers that work when the Tab is booted to ODIN? I've tried everything I can find and have been unable to get the correct drivers installed.
Click to expand...
Click to collapse
Install Kies and it should install the drivers. I'm pretty sure you can download them from samsung.com too. But when you use odin make sure that Kies is completely closed (even check in processes in task manager) or odin won't work
Sent from my GT-I9100 using xda premium
I am trying to install ics. I do what the link is telling me. It goes to the android icon and it installs 10-15 % then it reboots back to 2.3.5 what am I doing wrong
Which method were you using? Trying to install US version?
Here's a detailed thread if trying US version.
Hello All,
This is the tale of my personal journey to updating my RAZR to the .211 OTA. Please note that all of this is from my memory. If anyone happens to notice an error, please let me know asap! I’ll be sure to edit the post.
Hopefully my time yesterday will help other n00bs like me 
Backstory:
I was rooted on .181. I thought that I was 100% stock other than the root, but apparently that wasn’t the case. My first attempt was done via this method here: http://www.droidrzr.com/index.php/topic/2871-upgrade-from-181-to-211-sideload/
I tried this method because it seemed the easiest, but it did not work for me. It just simply booted me back into GB.
So… after reading, thinking, reading, thinking, wavering, thinking, and drinking for hours on end yesterday, I finally give this method a shot. This is my overly specific story of my success.
Numerous caveats before I proceed (seriously... read these):
1) In no way, shape, or form, is this information novel. I give all credit to Matt (his utility), andlaw, and RDA990 over at droidrzr.com and droidforums.com. THANK YOU ALL!
2) What follows is only the step-by-step of how I accomplished it. I am in no way, shape, or form responsible for what happens should you try this at home.
3) This is from where I compiled the information:
a. http://www.droidrzr.com/index.php/t...y-17-for-ics-and-those-who-want-to-go-to-ics/
b. http://www.droidforums.net/forum/dr...-installation-guide-droid-razr-razr-maxx.html
c. http://www.droidrzr.com/index.php/topic/2871-upgrade-from-181-to-211-sideload/
4) The process is actually simpler than it appears.
5) Make sure that you have a charge of at least 70% (I charged to 100% to be safe).
6) If for some reason you brick, see here to fix: http://www.droidforums.net/forum/dr...-installation-guide-droid-razr-razr-maxx.html
7) This method will wipe your phone (i.e, factory reset).
8) To my knowledge, this method only works if you are on .181. (but see the link in A for other versions).
9) My understanding from my extensive reading yesterday indicates that the reason some people were failing on the OTA update from the link above at droidforums is that the first attempt at the ICS installation replaces your stock Recovery but then fails to actually install. Some were getting errors the second time around as well.
10) This method worked flawlessly for me first attempt.
What you’ll need:
a) A Droid Razr (duh)
b) A Windows PC
c) Latest Motorola Drivers
d) Matt’s Utility 1.7
e) The OTA .zip file (Blur_Version.6.12.181.XT912.Verizon.en.US.zip)
f) Your USB cord
g) Download C,D,E here: http://www.droidrzr.com/index.php/t...y-17-for-ics-and-those-who-want-to-go-to-ics/
Steps:
1) Download Matt’s Utility 1.7.
2) Unzip it
3) Download the OTA .zip update file. DO NOT UNZIP IT
4) Make sure you turn on USB Debugging on your phone
5) Connect your phone to your computer via USB
6) Place the zipped OTA file on the EXTERNAL SD CARD of your phone. Please note that you can verify it’s in the right place by using ES File Explorer (available for free on the market). It should be located at “/mnt/sdcard-ext/”. You can also verify the md5 via ES File Explorer to make sure it matches that listed on Matt’s download page.
7) Change USB back to Charge Only
8) Turn your phone OFF
9) Hold Power, Volume UP, and Volume DOWN (all three at the same time). A menu will appear.
10) Press Volume DOWN until you get to AP Fastboot
11) Press Volume UP to enter AP Fastboot
12) Open the folder to which you extracted Matt’s 1.7 utility on your PC
13) Open the .bat file in Matt's Utility folder
14) Select Option 1. Let it do its thing. It replaces the stock recovery (along with some other stuff I don’t understand) so that you can then actually apply the update. This process actually takes a few minutes (probably something like 5-10 minutes).
15) When complete, turn your phone OFF using the on-screen (phone) instructions.
16) At this point, I powered back on, and the phone booted back into stock GB. I then setup Google account.
17) Turn phone OFF
18) Hold Power, Volume UP, and Volume DOWN (all three at the same time). A menu will appear.
19) Press Volume DOWN until you get to “Recovery”
20) Press Volume UP to enter “Recovery”
21) At this point an android will be on his side with an exclamation mark. Don’t freak out, this is supposed to happen.
22) Press Volume UP and Volume DOWN (both at the same time). This should enter recovery.
23) With the Volume DOWN button go down to "Wipe CACHE partition" and press the Power button to select it. DO THIS TWICE
24) With the Volume DOWN button go to "Apply Update from SDCard" and press the Power button to select it.
25) Press Volume DOWN until you get to “Blur_Version.6.12.181.XT912.Verizon.en.US.zip” and select it with the Power button. (This is the one we put in the External SD in Step 6.)
26) It will take a good bit of time to update. Mine took about 15-20 minutes.
27) Once the update is complete select "Reboot system now."
28) Grab a beer and pat yourself on the back.
29) Feel free to Root ICS 4.0.4. using Matt’s 1.7 utility (if you do, I believe you need to make sure to check allow installation of non-market apps – at least I did, and it worked for me).
30) Did I mention to have a beer?
31) See pics for verification (screen shots are built into ICS by holding Power and Volume DOWN!)
Sent from my DROID RAZR using xda app-developers app
method to unroot or upgrade from 173 update
Hi
i use droid razr xt912 with verizon
i am stuck with 173 update with eclipse rom. used the method from droidrazrroot.com to root my device
what is the ethod to upgrade from 173? please help
now i m unable to unroot my phone to get any new ics updates :-(
any help is much appreciated!!!
hi guys
i have Crony cn98 MID tablet (Chinese)
i deleted file bin from system folder by wrong
when i power up the tablet, restarting itself
what should i do to fix that problem
i have 2 tablets of this type
it means i can bring file bin
but how to put bin folder in the tablet?
i need help
no way to fix it ?
how to reinstall android os?
or install custom rom 4.0.3 from pc ?
for crony cn98
os : 4.0.3
kernel : 3.0.8+
no reply :crying:
I did some reading on your behalf, let's try to sort this out. Good news is you can't really brick A10 allwinner devices.
Ideally you would need the original firmware from the manufacturer (.img file) and flash it through livesuit. However, this firmware is no where to be found on their website, I would try to email the device maker to send you the firmware. The email is: [email protected]
1 . Acqure the firmware file from manufacturer
2. Download livesuit (http://www.mediafire.com/download.php?lawkcbqhbictar4).
Follow these Instructions to flash .img file through livesuite (I found them elsewhere):
3. Open LiveSuit.exe
Double-click to open the upgrade tool LiveSuit.exe
4.Select the firmware
Click the cube to the far left to select the firmware .img file.
5. Turn off your tablet
6. Press the key combination to start it in the upgrade mode
a. Press the "Vol -" key, then press the "Power" button, hold two buttons at the same time
b. Connect the USB cable to tablet and computer
c. After connecting the USB cable, press the power button 6 times quickly or hold the "Vol -" keys and the "Power" button for more than 6 seconds (you should get a pop up window if done correctly , if not repeat step 5 from beginning)
d. DON'T release the "Vol -" button till the LiveSuit window pops up
e. You can now release the "Vol -" button
(Note: If you install the driver at this time the pop-up dialog box, the path to point to installation directory UsbDriver LiveSuit folder, click Next to complete the driver installation prompts).
You should see LiveSuit window pops up; otherwise, you didn't do it correctly, you have to repeat step 4 and 5.
7. Select the format to force upgrade
Livesuit prompt "force format", click "Yes" (Y). All of the original apps installed will be removed.We highly recommend mandatory format! ! ! Otherwise the update is not complete and may brick! ! !
8. Upgrade begins
Pop-up "OK to force format" dialog box, select "Yes", the upgrade begins.
9. The upgrade is complete
Firmware download process last about three and a half minutes or so, please wait until the prompt "upgrade successful."
10. Automatic restart
After the upgrade is complete, your tablet will automatically restart, then you can unplug the USB cable.
Slow start-up for the first time, please be patient.
If the machine does not restart automatically, press and hold the Power button for 8-10 seconds or more to ensure the power switch off, then press the Power button 3 seconds or more to turn on your tablet.
11. Congratulations! You have flashed the firmware.
If you are not able to acquire the original firmware from manufacturer, you can try to flash this one:
http://www.yarvik.com/userfiles/yarvikfirmware/TAB461EUK_A404.img (funbook pro m500, similar specs and running same processor)
thank u very very much
i do that all but this frimware is not compatible (it show me all thing black)
i still need frimware
i send email for [email protected] but no reply yet
So I bought this cheap tablet off of ebay and after about a week I connected it into the charger and forgot to unplug it.. Only next morning I saw and when I disconnected it it had turned off. So I turned it on and it was stuck in the newsmy logo and wasn't booting up.
There was nothing on the internet, but somehow I got it working again and for everybody's sake I'm posting what I did here.
First off, even though there are some references that this has allwinner A10 inside, ITS NOT. you will brick this if you flash an allwinner variant kernal.
If you are one of those brave souls who flashed on a allwinner kernals and bricked the thing, you would not be able to go to download mode even. Here is the steps to flash a fresh rom that would resolve most of issues:
1. Download driver pack from the attachment of this post
2. Download RKBatchTool here: http://www.x-drivers.com/catalog/fl...s_electronics/models/rk_batch_tool/27576.html..
3. Now turn off your tablet. If it doesn't turn off press a needle head into the reset pinhole and hold it for 5 seconds
4. Open device manager from your computer
5. Then hold the power on button and volume up(that is the one closer to power button) until it turns on. It'll boot your tab in download mode. After the green robot icon appears connect it to the computer by carefully monitoring device manager of computer
*** If you have flashed an allwinner or other rockchip kernal based ROM earlier and do not go in to download mode or no new device installation in your PC there's a real possibility your download mode combination may have changed. Turn it off by pressing needle to reset pinhole. Then turn off and connect it to PC. Then turn it on and then while in boot screen hold volume up. if not try similar procedure by holding volume down or back buttons. If you see driver installation in the PC and nothing in the tablets screen, thats fine. You can continue with the flasing
6. The driver installation probably will fail. Identify which device that is newly added to the device manager.
7. Right click on the device -> Update Driver. Then manually select -> Have disk then give rockusb file from drivers you just downloaded(if your system is 64-bits use files in amd-64 folder)
8. Then select RK29 as the device and update the driver
9. Now extract and run RKBatchTool and you must see under connected devices button #1 highlighted in green
10. Download official ROM here: http://220.168.57.227:1949/cunchu/20120312T3youhuaruanj.rar
There are other ROMs for T3 here as well. But this is the only thing that works
11. Extract it and give its update.img file path to RKBatchTool FW Path
12. Hit Restore
13. Wait few minutes for flash to complete
14. Then the tab will restart once or twice and will start booting up. This process should take maybe 5 minutes or more. Be patient
15. Then it'll finally boot.
I will post a Jelly Bean ROM for this tab here as soon as I cook one
Comments are much appreciated
Thank you! Thank you! Thank you!
Was searching for a guide to get my brothers Newsmy Newpad T3 up and running.
Thank you for this guide. will definitely try it out and leave a feedback.
P.S. Jellybean sounds interesting.
OK. After spending two days I finally got it to detect the Newsmy Newpad T3.
I had to install Android SDK for the USB drivers. (Don't know if it detected from that.)
Then downloaded super one click root. Found the android drivers in it, and when it asked which driver you want to install I gave "Android Composite" not sure but something in those lines.
Successfully rooted it.
Then off the tab and connect the USB cable, press power and volume up (one that is near the power) and when the tab boots
If it asked for drivers please do same as above
Now run the firmware installer provided inside the update.img folder that you downloaded from the original post by suki300me step 10. It is in Chinese and the first option is to change it to English found on the bottom screen.
If everything is set your tab will be in a black screen only thing you know is that it is on is the sound windows 7 makes when the phone is connected to it. Choose the udate .img file and press upgrade.
It will run up to 3-4 stages and will say data copy error. Remove the cable and press power, it will star installing ICS give it few minutes and you are done.
It took me many attempts so don't give up if it didn't work on your first try. Hope this helps someone.
Boot
Hi
I get one newsmy t3 tablet from my friend. The only problem the system is never loaded (stuck at the boot). I try the power+volume up but just the black screen appaers. Btw only turns on when its plugged. Please give me some tips.