Please guys tell me,what should i do....i installed a Miri ROM long time ago and he starts to crash to freeze ...i decided to return to stock and when i installed the 1.66 WWE rom it works for 2 days and yesterday my phone refuse to start,remains in the white screen.
I tried with the hard reset but still remains at the white screen,i tried to install a new ROM but every time says that the files are corupt...
I also tried with the FAT32 method but after 25% stops and gives me a fail...
Please,what should i do???
Budan Andrei said:
Please guys tell me,what should i do....i installed a Miri ROM long time ago and he starts to crash to freeze ...i decided to return to stock and when i installed the 1.66 WWE rom it works for 2 days and yesterday my phone refuse to start,remains in the white screen.
I tried with the hard reset but still remains at the white screen,i tried to install a new ROM but every time says that the files are corupt...
I also tried with the FAT32 method but after 25% stops and gives me a fail...
Please,what should i do???
Click to expand...
Click to collapse
Will the phone reboot into the bootloader screen?
Also PLEASE in future post questions in the correct forum. Thanks.
Mark.
If i restart the phone,the same will happen.Stucks on the white screen.......
Budan Andrei said:
If i restart the phone,the same will happen.Stucks on the white screen.......
Click to expand...
Click to collapse
You enter the Bootloader screen by holding down the 'volume down' button while rebooting or powering up the phone.
Mark.
Yes,the phone enters in the bootloader mode.
Budan Andrei said:
Yes,the phone enters in the bootloader mode.
Click to expand...
Click to collapse
What version of SPL does the bootloader screen give you?
Mark.
Spl-2.08.hspl
Budan Andrei said:
Spl-2.08.hspl
Click to expand...
Click to collapse
Usually if the phone gets stuck in the white screen then it means the Radio is incompatable with the installed Rom so you have 3 options that I can think of.
Download the latest Radio (2.15.50.14 as far as I know) and flash it via the bootloader screen in activesync mode.
The second option you have is to download a different rom than the one you chose last time and install it via the same bootloader activesync method.
Lastly could also download the latest stock rom from your provider and flash it via the sd card method which should reset all parts to stock version.
Mark.
Related
All,
So I wanted to switch to TMobile from AT&T. I backed up my rom with the XDAtools to my SD card. Then I loaded the special edition rom... Everything was working and the phone was unlocked.
Then I reloaded my backed up ROM... That was when I got really really mad. The restore went fine, but upon restart.... NOTHING. Now I cannot turn on my device and the LED just blinks red once.
Please help. Any ideas are appreciated. I've had the phone over a year and I believe the warranty has expired.
HELP ME SEYMOUR!!!
Brynomon
Can you get to the boot loader screen with "GSM Ok" message ?
What boot loader version ?
I get nothing. Screen doesn't even come on. The send key just turns green and the alert light blinks red quickly one time.
Biso007 said:
Can you get to the boot loader screen with "GSM Ok" message ?
What boot loader version ?
Click to expand...
Click to collapse
Sure you did, but i will ask for it...
Have you tried another hard reset of the device?
STefan
Yup I sure did.
LumpiStefan said:
Sure you did, but i will ask for it...
Have you tried another hard reset of the device?
STefan
Click to expand...
Click to collapse
I was going to AT&t to try to get a replacement because the keyboard was very loose so I was flashing everything back after flashing the rom back I was flashing the stock hard spl but instead of replacing the nbh file I just put the file on my storage card and flashed it (VERY STUPID)
When I turn my phone on I get the tricolor screen and a message that says: Upgrade ROM code error Please try agian =
and nothing happens I tried hard reseting it but nothing happens, I can't get past that screen, I also tried flashing a new rom through the storage card method since I can't connect with Active Sync
Please help me , I just got my phone in November and I don't want to loose it, I would like to see what help I can get before going thought ATT customer service and telling them I didn't do anything and that it just happened by itself
Thanks to any people who respond
i think to flash a rom from pc u don't need to be connected to active sync try conecting while in tri clour screen and flash the rom
or could u say what exactly happened where u trying to flash a rom or what?
i tried now with my touch pro i entered boot mood then tried connected to pc to flash a rom and it worked it started.......
Thegreat1 said:
i think to flash a rom from pc u don't need to be connected to active sync try conecting while in tri clour screen and flash the rom
or could u say what exactly happened where u trying to flash a rom or what?
Click to expand...
Click to collapse
I was trying to restore the stock hard spl, don't
Thegreat1 said:
i tried now with my touch pro i entered boot mood then tried connected to pc to flash a rom and it worked it started.......
Click to expand...
Click to collapse
did u connect to Active Sync or through the storage card
no active sync
just entered boot mode then put the usb cable then started the flashing process
Thegreat1 said:
no active sync
just entered boot mode then put the usb cable then started the flashing process
Click to expand...
Click to collapse
I get an error during the flashing process, i was flashing the hard spl
read the first paragraph on the first post, I added exactly what I did wrong
u were trying to flash hard-spl when it hanged in the tri-clour screeen?
did u revert back to stock rom before trying to revert to stock spl?
Thegreat1 said:
did u revert back to stock rom before trying to revert to stock spl?
Click to expand...
Click to collapse
ya, read the my first post again, I added some stuff
Thegreat1 said:
u were trying to flash hard-spl when it hanged in the tri-clour screeen?
Click to expand...
Click to collapse
yes, after I messed it up the first time
if you can get to the boot loader screen you can probably flash any rom. simply rename the rom file to RAPHIMG.nbh and place it on your memory card, hold volume down + reset with stylus. you should be set. good luck.
does the bootloader still show the olinex 1.90
warren2781 said:
if you can get to the boot loader screen you can probably flash any rom. simply rename the rom file to RAPHIMG.nbh and place it on your memory card, hold volume down + reset with stylus. you should be set. good luck.
Click to expand...
Click to collapse
tried it, it doesn't work
Thegreat1 said:
does the bootloader still show the olinex 1.90
Click to expand...
Click to collapse
No, I am trying to flash it back to the olinex 1.90 but I keep getting an error in ruu
Have you tried this http://forum.xda-developers.com/member.php?u=467141
try flashing hard-spl once again. if it works your saved. as far as i know the people over at att only check for water mark at least in my place the y do. good luck
I found that it was not possible to flash the HardSPL from tri-colour screen.
It only worked for me when windows mobile was fully booted. When you start the HardSPL RUU the phone's screen will just go black, and will return when the update is completed.
I would try connecting the phone while in tri-colour mode, then running the original rom RUU on the PC and seeing if it works. If it gets to the stage where the loading bar shows up on the phone you should be ok.
Once the rom is loaded, start your windows mobile, connect to the PC, and run the RUU for HardSPL.
Best of luck to you!
Thanks for your guys responses I have successfully recovered my phone, I just flashed the original ATT rom from ruu
Very glad that you found solution to fix that problem, because it could happend to any one. Especially after I was thinking to flash everything back to att stock because of my usb exit is getting loose.
mr.denis said:
Very glad that you found solution to fix that problem, because it could happend to any one. Especially after I was thinking to flash everything back to att stock because of my usb exit is getting loose.
Click to expand...
Click to collapse
Thanks, ya, you just have to be careful and read directions if present and read them carefully
hello evrey body
i installed miri "Miri & Steve0007 Elegancia V4.0 | Sep 13" rom on my mobile and evrey thing worked well then i made soft reset but Unfortunately while it was reseting it stopped on the white screen where it written htc in green font, then i thought maybe it take long to reset so i waited for about 30 min but nth happened. Then i made hard reset and nth worked.
After that i decide its better to make format but i faced the same problem while i was formating cuz its also stopped on the color screen where the color is red blue green white, I tried several times but it keeped stoping, I also tried to install new rom but its imposible, cuz the mobile doesn't boot to windows so the windows mobile center cant find it.
Can anyone help me please??????
Sir, you are looking fore help, but you don't give much information.
Oky you inform us witch rom you are traying to install, and that you have some problems with it. (it's obvious following your thread title)
but if you would some help there needed some more information.
HSPL version?
Radio version?
Device? Europa/usa model?
Did you tray to reinstall stock rom?
Did you read/follow the instructions on the threads where you got your cooked rom?
rafatgt said:
Unfortunately while it was reseting it stopped on the white screen where it written htc in green font, then i thought maybe it take long to reset so i waited for about 30 min but nth happened. Then i made hard reset and nth worked.
Click to expand...
Click to collapse
you did flash a matching radio, right?
You MUST use radio:
2.07.50.27 or 2.08.50.08_2 or 2.10.50.19_2 or 2.10. 50.08_2 or 2.09.50.29_2 or 2.10.50.26 -(Latest 2.13 T-MOU Radio)
Or 2.11.50.20 or 2.12.50.02
Click to expand...
Click to collapse
thats from elegancia post 1
rafatgt said:
I also tried to install new rom but its imposible, cuz the mobile doesn't boot to windows so the windows mobile center cant find it.
Can anyone help me please??????
Click to expand...
Click to collapse
dont need to have running phone to flash. Go into bootloader, connect usb, wait for 'serial' to become 'usb' and flash your rom or radio, , , for you you should now flash a radio and i bet the phone boots.
Hello guys i have a problem with my HTC HD2.
I have searched a lot on this site before posting my problem.
This is what happens and what i did:
The phone doesn't pass the white HTC screen with the RGD letters below.
What i have tried:
HSPL 2.08.HSPL, 1.66, 1.42, 2.08.000
Radio: Leo_RADIO_2.08.50.05, Leo_RADIO_2.15.50.14
Roms: Stock Vodafone (Dutch) rom, Energy rom
Hard reset (vol up +down on startup).
Tried task 29 and started everything all over again
I went to the a phone store, they couldnt help me. Afterwards i went to the official store but i don't have my receipt anymore so i don't have a warranty..
So i think i have tried everything i could find on this forum. Tried most of the HSPL versions with diferent roms. But all of them stay on the startup screen (white htc start screen)
If someone can help me please, this is really my last chance
Thanks,
Issam
ps. i hope this is the good section to post this problem.
Well the phone starts up now (it actually works for a few minutes!). I haven't changed anything, the only thing i did is leave the battery out for like 1 hour. But everytime i start up the phone it freezes and / or turns of after 1 min or something. Sometimes it doesn't even boot up like the usual problem, but then i remove the battery for 10 minutes and it boots normal again.
So i really don't have a clue
i was experimenting all day again with my htc.
What i found out was, the longer i keep my battery out of the phone the longer i can use it.
For example: I had the battery out of the phone for about 2 hours, when I put it back in i could use it for like 10 minutes.
But when i keep the battery out for 10 minutes it freezes within 1 minute.
Maybe this will help me get the solution to this problem.
I would format the sd card just in case, also make sure you have the correct versions of what you need, rom raido ect, because theres two types of HD2s, hope this helps!!
Thanks for the reply, i tried formatting the SD card and i succeeded doing it 5 times i think. I think i have the correct version of rom and radio, how do i know?
IssamRazza said:
Thanks for the reply, i tried formatting the SD card and i succeeded doing it 5 times i think. I think i have the correct version of rom and radio, how do i know?
Click to expand...
Click to collapse
You should remove hspl , and after that install the latest rom available on htc site for your device (download the rom from htc site, with your serial number ) . Official roms have included radio inside of them. If HSPL is removed and you have again problems with your device with an official rom installed, then you have a hardware problem. You could try to boot up without sd card installed, to see if the card is the problem.
Thank you,
I will try removing HSPL and install the original ROM from the HTC site. I'll let you guys know.
IssamRazza said:
Thank you,
I will try removing HSPL and install the original ROM from the HTC site. I'll let you guys know.
Click to expand...
Click to collapse
I see that you are on t-mobile network , so you should download your rom from here: http://www.t-mobile.com/wmupgrade/ . Just enter your imei and download the update. Remove HSPL and then install the official rom. Perform a hard reset after that , and see if is all ok . Keep us informed pls.
Hi, yes i have a T-mobile contract, but my phone is Vodafone branden so i'll have to download the Vodafone version I think.
But what i just did is this:
I had HSPL 2.08.HSPL and a Custom ROM on it. So I was planning on maybe sending it back. Thats why I performed a task 29 to delete all the previous (parts of the) Roms. After that i changed my HSPL to 1.66.000, the original spl I had on it.
But now the phone does vibrate when i hold the power butten (with vol down), but there is no picture, so i cant get into the phone or the Red green blue screen. So i think the phone will not boot because I deleted the Rom on the phone and also returned the spl to original.
Is there a solution for this problem? omg this phone just doesn't seem to be working for me (maybe it's me that is not working for the phone).
It is normal since you did a task29. Verify if you did it correctly here http://forum.xda-developers.com/showthread.php?t=644781
Yes i have read that thread thank you, but the question is:
How can i get the phone to connect with my PC, so I can install original ROM. Because the Boatloader screen won't start up, to make connection with my Computer. I press the power button and vol down butten at the same time. Tried it at least 20 times
Thanks you all. But i sent this phone back to HTC. The board was replaced and they sent it back, so it works again! finally my phone back
Hello, I have a problem with my HTC HD2, it doesn't want to start. When I press the power button I feel only a tiny vibration, but only when the device is connected to a power source. Without power source it won't do anything.
Things that I've done : The phone was stuck in bootloader with the error "Upgrade ROM Code Error , Please try again", it had SPL 2.08.0000 so I've flashed HSPL 2.08. After that my device wouldn't start.
Things that I've tried : Take the battery away from the device , connect the device to a power supply,wait 5 minutes then put the battery back on.
Hard-Reset.
Tried to enter bootloader.
Also tried to flash the stock rom, before flashing HSPL 2.08. My device was stuck at 0% with no progress what so ever.
Please help !
hello
I just both a new HD2 from Amazon and the thing don't want to start.
I started first time and it crashed at the training for keyboard. I removed the battery and it didn't want to start again. I did the reset, hard reset but it stay with a white screen and htc logo on. Is not doing anything.
I tried also to start it without SD-card and phone card but no change.
What to do should I send it back????
thank you.
NeXuSqtek said:
Hello, I have a problem with my HTC HD2, it doesn't want to start. When I press the power button I feel only a tiny vibration, but only when the device is connected to a power source. Without power source it won't do anything.
Things that I've done : The phone was stuck in bootloader with the error "Upgrade ROM Code Error , Please try again", it had SPL SPL 2.08.0000 so I've flashed HSPL 2.08. After that my device wouldn't start.
Things that I've tried : Take the battery away from the device , connect the device to a power supply,wait 5 minutes then put the battery back on.
Hard-Reset.
Tried to enter bootloader.
Also tried to flash the stock rom, before flashing HSPL 2.08. My device was stuck at 0% with no progress what so ever.
Please help !
Click to expand...
Click to collapse
battery out, connect to wall charger and turn charger on, insert battery, dont touch it for a good half hour. dont worry if charging light doesnt come on straight away.
It sounds like the battery is possibly over discharged. doing as i listed 'should' let the phone start charging without trying to turn itself on.
ktod_16 said:
hello
I just both a new HD2 from Amazon and the thing don't want to start.
I started first time and it crashed at the training for keyboard. I removed the battery and it didn't want to start again. I did the reset, hard reset but it stay with a white screen and htc logo on. Is not doing anything.
I tried also to start it without SD-card and phone card but no change.
What to do should I send it back????
thank you.
Click to expand...
Click to collapse
yes send it back, silly to try and fix an error with a brand new phone. (Also, hijacking threads is considered bad manners. )
Thank you very much samsamuel,by the way I have one more question to ask : Is it possible to brick the device by simply flashing HSPL 2.08 ? (SPL 2.08.0000 was installed)
I will try your method and I will keep you informed on my progress.
Thanks a million.
Hi!Unfortunately i have a big problem with my hd2.I have hacked it with hspl3.I have it 4 months now and i have flash to it about 10 roms.After i flashed the last rom suddenly my hd2 closed and when i opened it showed a white screen.I tried
to do reset to last official greek rom of htc(HD2_RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship)changing the name of RUU_signed.nbh to LEOIMG.nbh and put it in to sd card.And in 5% shows me "update terminate,update fail,radio v2 fail" and then when it starts shows white screen again.I can get only in bootable mode (that mens in the screen with the colors ni wich you can see wich spl you have)How can i fix my hd2 pls?
NeXuSqtek said:
Thank you very much samsamuel,by the way I have one more question to ask : Is it possible to brick the device by simply flashing HSPL 2.08 ? (SPL 2.08.0000 was installed)
I will try your method and I will keep you informed on my progress.
Thanks a million.
Click to expand...
Click to collapse
it's highly unlikely, but as with anything of this nature nothing is foolproof
elgeor said:
Hi!Unfortunately i have a big problem with my hd2.I have hacked it with hspl3.I have it 4 months now and i have flash to it about 10 roms.After i flashed the last rom suddenly my hd2 closed and when i opened it showed a white screen.I tried
to do reset to last official greek rom of htc(HD2_RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship)changing the name of RUU_signed.nbh to LEOIMG.nbh and put it in to sd card.And in 5% shows me "update terminate,update fail,radio v2 fail" and then when it starts shows white screen again.I can get only in bootable mode (that mens in the screen with the colors ni wich you can see wich spl you have)How can i fix my hd2 pls?
Click to expand...
Click to collapse
bad news for you i'm afraid. i'm not aware of any successful fixing of radio update error.
Ok,thanks, I hope that the battery is the source of this problem,not the device .
I went today at a local service,they've told me that the battery is 100% charged. Unfortunately the problem is with my HD2. I left it in service and I will pick it up tomorrow repaired I hope. Thank you for helping me.
NeXuSqtek said:
Thank you very much samsamuel,by the way I have one more question to ask : Is it possible to brick the device by simply flashing HSPL 2.08 ? (SPL 2.08.0000 was installed)
I will try your method and I will keep you informed on my progress.
Thanks a million.
Click to expand...
Click to collapse
YOU GOT WRONG HSPL you should have 2.08. 6666 etc not 0000... I hope this helps
Nice thread
netvpn7 said:
YOU GOT WRONG HSPL you should have 2.08. 6666 etc not 0000... I hope this helps
Click to expand...
Click to collapse
I knew I made a mistake, my question now is can it be fixed ?
Hi, I tried to instal Android 2.3 Gingerbread on my htc hd2 but when I installed MAGLDR it stopped working. I realized I had installed the wrong HSPL, but now it won't start or respond to a USB connection. I can't turn it on or off and it only shows a white image with HTC on it....Does someone know how to help?
Greetzz
pull battery, restart into bootloader, apply 2.08.hspl,restart.
My HD2, won't start up.
My plan was to remove an ICS rom, but during my reinstallation of an other rom everything got deleted..
Now my problem, it won't load into MAGLDR, I do have HSPL 2.08 etc.
Does someone have an idea?
---------- Post added at 05:58 PM ---------- Previous post was at 05:57 PM ----------
Mark-- said:
My HD2, won't start up.
My plan was to remove an ICS rom, but during my reinstallation of an other rom everything got deleted..
Now my problem, it won't load into MAGLDR, I do have HSPL 2.08 etc.
Does someone have an idea?
Click to expand...
Click to collapse
Finally I was able to load my HD2 into MAGLDR so problem solved..