Yes I made a mistake (**** happens) and now when I boot my phone i get "Failed to boot 2"
and it goes into SBF mode. prior to this I was on gingerbread 2.3.4, on bell in canada.
I've seen guides offering a 2.1.1 SBF that can be used to fix a phone, but I'm worried using this will brick my phone since I'm on 2.3.4
I've seen plenty of warnings not to use an ATT SBF, but nothing about using an older bell version.
derkinit said:
Yes I made a mistake (**** happens) and now when I boot my phone i get "Failed to boot 2"
and it goes into SBF mode. prior to this I was on gingerbread 2.3.4, on bell in canada.
I've seen guides offering a 2.1.1 SBF that can be used to fix a phone, but I'm worried using this will brick my phone since I'm on 2.3.4
I've seen plenty of warnings not to use an ATT SBF, but nothing about using an older bell version.
Click to expand...
Click to collapse
why don't you just reflash a 2.3.4 sbf? i wouldn't risk hard bricking your phone; as long as you can get into RSD mode and can flash a sbf with RSD Lite, then you're fixable.
or better yet, reflashing the pudding .sbf (if you're unlocked)
btw, what was the mistake you made? this can help me solve your problem.
there is no 2.3.4 sbf available for bell, and i didnt unlock
my mistake was trying to install CM without unlocking the bootloader, i misread some things, and I'm kicking it myself now.
I did see one thread during my searching of a guy who successfully used an AT&T 2.3.4 SBF on his bell atrix, so I'm contemplating trying that
other than that I can try sending it in and getting the phone repaired (which will most lilely be denied based on me voiding the warranty) and past that, I drop 500 bucks on a new phone, and being a teenager saving for univeristy, thats annoying.
So I loaded up the AT&T sbf in RSD lite, and it wouldnt even let me try to flash it
as a shot in the dark i tried using pudding (IHOP), and it tried, and failed.
pretty much out of ideas at this point, only bell has the sbf my phone truly needs so I'm gonna take it in tomorrow and hope for the best.
Related
Is it possible to flash a Bell Atrix with an AT&T sbf in order to make it compatible with Gingerblur. I understand that it has been next to impossible to find a Bell sbf, so it would be nice if this could be an alternative method.
IrshaadH said:
Is it possible to flash a Bell Atrix with an AT&T sbf in order to make it compatible with Gingerblur. I understand that it has been next to impossible to find a Bell sbf, so it would be nice if this could be an alternative method.
Click to expand...
Click to collapse
it's next to impossible to find a Bell sbf simply because it's not out there. moto canada has it, and i expect bell probably has it too, but they sure as hell aren't sharing.
also, it is impossible to flash AT&T sbf's to Bell phones. If you download RSD Lite, and an AT&T sbf, then try to flash the sbf, it simply won't start. RSD will recognize that your phone is connected, and will also recognize that you have selected a valid SBF file, but won't let you hit the "start" button to start the flash.
Hi, there are probably numerous questions similar to mine, but I couldn't find the right thread for me.
I recently unlocked my atrix's bootloader, and tried to update to the gingerbread update. Ultimately, I wanted to flash the Alien rom, but the gingerbread update (not the OTA one), caused my phone to be stuck on the Moto logo, so I flashed the 1.2.6 sbf on my phone.
Now, I'm not sure what I should do to update my phone to gingerbread since I read that if I update directly from 1.2.6, I will hard break my phone. What should I do?
By the way, I have been having troubles with an update to 1.8.3 via sbf. It keeps saying that the phone did not enumerate.
Thanks for all the help!!
phillyf8n said:
Hi, there are probably numerous questions similar to mine, but I couldn't find the right thread for me.
I recently unlocked my atrix's bootloader, and tried to update to the gingerbread update. Ultimately, I wanted to flash the Alien rom, but the gingerbread update (not the OTA one), caused my phone to be stuck on the Moto logo, so I flashed the 1.2.6 sbf on my phone.
Now, I'm not sure what I should do to update my phone to gingerbread since I read that if I update directly from 1.2.6, I will hard break my phone. What should I do?
By the way, I have been having troubles with an update to 1.8.3 via sbf. It keeps saying that the phone did not enumerate.
Thanks for all the help!!
Click to expand...
Click to collapse
I'm surprised you aren't already hardbricked.. Use the OTA updates until 1.8.3 (RSD shouldn't be used at all really) and then re-root and unlock whatever using: http://forum.xda-developers.com/showthread.php?t=1182871.
If it did not reenumerate, then all you should do is boot back into RSD and see whether that fixes it.
http://forum.xda-developers.com/showthread.php?t=1163342
this gives stock 2.3.4 without touching bootloader
My Atrix went from stock to rooted, unlocked BL, and then installed Kenneth's beta 4.5, then installed the wipe version of Alien (2nd release, I think).
My touchscreen has stopped responding, so I can't maneuver in the phone and need to try to get it in a state where AT&T will switch it out for me without having a hissy fit.
I've been reading snippets that I'm ok to SBF to 2.2.2, or that I should use fruitcake. Which should I do? Or is there another method?
I apologize if this is already covered, I searched for hours, and either its not there, or I don't know the right keywords to search by.
Any help is greatly appreciated!
First did fruitcake, then did the RSD lite route. Both worked, but the RSD lite route got me what I wanted.
Thanks
rileyh1278 said:
First did fruitcake, then did the RSD lite route. Both worked, but the RSD lite route got me what I wanted.
Thanks
Click to expand...
Click to collapse
Did you get hit on the warranty exchange for having an unlocked bl? I know it doesn't say UNLOCKED if you flash the stock 4.5.91 but it's still unlocked.
I'm sure people want to know just in case they get in the same situation.
At that point would it be in the users benefit to brick the phone intentionally by flashing an older sbf?
I know it's fraud but just curious.
I was trying to apply the OTA 4.5.141, on my rooted AT&T Motorola Atrix stock rom 2.3.4 and after the first reboot, following the instructions from the update, I am getting the message “failed to boot 2 starting rds mode” and just sit there. After removing the battery and booting up again, the phone seems to booting up normally and then when the phone finishes loading most of the widgets, I get a message saying “turning off” and the same cycle keeps repeating.
This is my primary phone and I am really desperate right now and I do not know what to do.
Please I need some help,
You could try to use RSDlite to flash the official 4.5.91 SBF, info in the 2.3.6 OTA thread and then apply the 141 OTA. There's still a chance that the update will fail though . Worst case you will have to use fruitcake 2.3.4/2.3.6. Info on that is also in the same thread. If you just want your phone to work with no hassle use fruitcake and don't apply the official OTA update.
Thank you for the information it was very helpful.
I am pretty new on android and my experience has been on windows mobile phones mainly (flashing, unlocking and installing roms) and I can see know that my problem it’s that I tried to update my phone without removing the root access.
Now I have RDS lite 5.6 and I am trying to find the official 2.3.6 stock rom and because this is my first time flashing an Android phone, I am very nervous to tell you the truth and I don’t want to brick my phone. It’s there any tips you have to not screw up the whole thing.
I am following a guide found on atrix forums to use RDS lite to flahs my phone. [HOW TO] Use RSD Lite to Flash a SBF File - Motorola Atrix.
Thank you again,
I got it working again following the suggestions from Atrixforums.com. What I did was to flash my phone with RDS lite v5.6 using the file 1FF-olympus-user-2.3.4-4.5.91-110625-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P011 and that fixed my phone and it’s been working normally.
Notes:
My phone was using the stock rom version 2.3.4
Rooted (I did not remove the root access before applying OTA 4.5.141 and this is reason why I got in this problem)
Locked bootloader (I am not sure if this method will work with an unlocked bootloader)
Unlocked sim card
Thank you,
I recently rooted my Photon 4G and even more recently updated it to the new 2.3.5, but would now like to unroot it. I tried using the RSDlite and sbf method as seen by qbking of ACS, but I get stuck at the "re-enumerating" error, as I have seen many others have. Is there any way I can fix this and continue on?
smartsoldier said:
I recently rooted my Photon 4G and even more recently updated it to the new 2.3.5, but would now like to unroot it. I tried using the RSDlite and sbf method as seen by qbking of ACS, but I get stuck at the "re-enumerating" error, as I have seen many others have. Is there any way I can fix this and continue on?
Click to expand...
Click to collapse
Do not flash any SBF onto a updated 2.3.5. theses are designed for a 2.3.4. system. You can do serious damage up to and including bricking the phone. QBKing had a good idea but most of his videos are now out of date.