When I try to mount my Archos 70 to my PC via USB, the Archos displays the little green robot with the 'mount/cancel' options but won't accept a touch on either of the buttons.
If I repeatedly go to home and then pull down that same screen from the notification bar it will eventually accept the 'mount' command but it can take 5 or 6 tries.
This is relatively recent and happens with a variety of cables. Any solutions out there?
Related
I have a problem with my Galaxy Tab 10.1, yet can't seem to figure out where to start troubleshooting.
Having the Tab since it was released, until now, I had yet to experience any problems whatsoever. But upon turning (or trying) to turn my Tab on, all that welcomed me was a black screen. I know the various button combinations, screen rub trick, and holding the power button long enough to help boot the Tab up but none of this worked. I thought maybe my battery was dead (even though I has seen it at about 60% before the problem) and decided to plug it in.
Once plugged in, the battery charging indicator came on and looked like it was about to show the battery filling up. Instead, the screen turned off immediately one second later and then popped up again with the battery icon. It would then just go on and off. Holding the power button would result in the "Samsung Galaxy Tab 10.1" welcome screen, but this would transition back to the battery icon, and turn off as usual.
I was able to access the two icons (box with an arrow and android; and android with download underneath) by holding power and vol. down. Clicking on the first icon with the box would just turn off the Tab and restart the battery icon. But clicking on the android that has the word download underneath takes me to a screen that I don't know what to do with.
This all happens while plugged in to the charger, and goes away immediately (turns off) if I take out the cord. I have tried to use the NVflash method but am basically stumbling in the dark because my computer doesn't recognize the Tab when I plug it in. It does say installing device when plugged in, but I cannot find it under devices.
Any help would greatly be appreciated!
P.S. My Tab (32 GB) has an unlocked bootloader, but the unlocked sign does not show up when I plug it in and and the Samsung welcome screen breifly pops up.
I am not a developer, so ultimately someone else will help you more than I, however the fact that you can get to ODIN means you will be able to save your tablet. There are some posts in the development section about using ODIN (that’s where you go after selecting the icon on the right), but you will be able to flash everything you need to in order to get back on your feet from within ODIN.
3 weeks ago I finally spent the $20.00 and replaced the defected battery in my Sanei N78 tablet. During the week that followed I had no trouble that is till a week later.
After using my Tablet till the battery ran down and shut it self off I plugged it in to recharge. This time however, instead of getting the Android opening screen, I got nothing. So I pressed the power button till the Sanei's logo spinning color wheel page appeared. But, instead of continuing booting on in to the Android opening screen, it just stayed stuck on that spinning color wheel.
Since this has happen to me before I proceeded to use what I call the reset command (pressing the power and up volume buttons simultaneously).
Yet, instead of giving me a choice to reset or not, all I got the Android logo laying on its back with its access panel open and an exclamation point in a red triangle. Which after a few minutes returns to the spinning color wheel page?
I keep trying difference combinations of the power/volume up/volume down buttons; however, all I get is the "dead" Android logo or the spinning color wheel.
I have also tried disconnected the battery and let the Tablet sit unpowered for the next 48 hours - It didn't work:crying:
What has gone wrong?
Has the “drive” containing the Android operation system failed? Has Android itself become corrupted? Is there a fix?
When I asked this question to a site that sell only Sanei tablets I was told to hold the power button for 5 to 10 seconds. Well, I have and nothing changes. I was also informed that another answer is to reinstall the firmware.
As for the latter, I would like to try, but, the only way I could is to download it to a thumb drive from the computer I am using to post this message and either run it off that or use my home Win98 OS computer (BTW: I have connected the tablet to my home computer and while 2 drive icons do appear in My Computer any attemp to open them give me a "drive not ready" message. This because this public computer that I am using will not premit under any cirsumstances a tablet to be connected to it
Is this possible?
If not, then I have another paperweight for my desk
Hi, I've literally searched anywhere and cannot find any answers but i have a HP chromebook 14 and wish to enter developer mode. It used to before but i had to powerwash with a failed linux install and when i hold escape + refresh + tap power it does nothing. if i hold power with the other 2 it logs out then another attempt shuts the system down. The escape key and refresh keys function alone.
is it possible there is a hardware problem where it wont accept all 3 combined? Bearing in mind i have tried an external keyboard and got the exact same result.
I've tried:
external keyboard
powerwash
all different channels of chrome (stable, beta and developer)
trying the key presses in every different combination from opening the lid etc
also refresh + power dosnt hard reset it just does the same as with escape being held down.
Could there be a software problem linked with the key presses? I really want some help because i find where i live now and the lack of wifi out and about unbearable to use this machine without some way to work offline and install to SSD
Thanks in advance if you can help
Turn on your chromebook and hold down ESC+refresh+power until it turns back on to a screen says "chrome os is missing or damaged" at this screen press Ctrl+D and press enter at the next screen it should turn on developer mode. This will take about 10 minutes or more depending on how much stuff you have on the Chromebook. After it finishes reboot and at the screen that says " is verification is off" press Ctrl+d and then you should be able to log into google.
can i do it with an hp 14 chromebook? the model is ak-039wm
Hope you guys can help me out, to cut the long story short, I've an old tablet, of which I've forgotten the pattern on and best of all, I've forgotten the email too!
I tried connecting it with my laptop (running Windows 8.1). It only detects as charging cable and from what I've read, I think USB debugging is set to "off" and I can't go to settings and enable it.
I've tried the volume up + power button boot option, it opens the said menu, I select" Recovery mood" the little android bot comes that it's initializing system, etc, and then after few seconds, another animation comes with green android dead with red triangle exclamation mark, written "Error" below only. I tried doing "volume + power" didn't worked.
I've exhausted almost all my options here, any help would be much appreciated.
It's an ASUS tablet.
Thanks
Moto X Style not rooted
I have show touches on so I can see that the screen recognises the input but the phone won't correspond with what I'm telling it to do. Even when using a mouse via USB debugging.
Every time upon restart, it works properly for a minute or so, then the navbar & statusbar dissapear, screen fades to black and locks. When I press the power button, it shows the lock screen but won't let me press anything. Apart from the Power Off pop up when it appears. I also can still interact with the always on display.
If I boot it in safe mode, the issue doesn't occur and I can interact the screen indefinitely.
I've not installed any new apps recently but this just started happening about a day ago.
Any ideas of what's wrong/how to fix it?