Related
Since I haven't seen many people here mentioning it, I thought it'd be useful to talk about my experience with Brando anti glare protector for Touch HD.
Few months ago, when I stockpiled on the protectors, I ordered one, just for the testing purposes. They were cheap, so I figured why not.
Now that my previously used ultra-clear protector got badly scratched and even deformed after a situation in which my Touch HD fell face down directly onto a neck of a beer bottle (don't ask) I realized I had to change it. The screen magically survived without any trace of contact, and I was very lucky for having the protector on - without it, I'm sure the screen would've had to be replaced.
Applying the protector
So, I pulled out the anti glare protector and applied it. First of all, the application procedure was slightly easier then with ultra-clear. The anti glare protector seems to be a bit stiffer and requires only one side of the protector to be peeled off before application, whereas the ultra needs 2 protective layers removed. It could also be simply the fact that I got some practice with these things now... But it felt easier in any case.
Fit
As with other Brando protectors, this one is also a bit too short on the bottom. If you start directly at the top of the device screen, leaving absolutely no space between the protector and the screen edge, at the bottom side you'll end up about 1.2 mm too short. For me it's not a big problem, and I certainly don't notice this, since the bottom part is usually covered by hand or fingers, but people who insist on perfection may find this annoying. The cut out for the speaker seems to sit well in it's place, and also be aware that there is a U-shaped cut out for the front camera. The ultra clear covers the camera, but obviously because of the grain-effect I'll get to in a moment, this was not possible here.
Brightness
After applying it I was very happy with the overall look. The screen brightness was the same - I did not notice any reduction in this regard, so I can say that this is very good in terms of transparency.
Sharpness and visibility
As for the sharpness / visibility, I'm hesitant to even say it, but there is a small difference when compared to ultra clear, or no protector of course. But it's a small difference. The effect is sort of like a very, very fine grain pattern across the screen, but I can't stress this enough - it's really no big deal. I'm a photographer and I work with graphic editing software, so my eyes are trained to notice every damn detail. For most people, I would assume that they would hardly notice any difference. So, to cut the long story short - the sharpness stays the same, but you get a gentle grain effect which is usually noticeable only on white background.
To sort of get a feeling of what you can expect, I can recommend you open up a bitmap in Photoshop and add 1 percent uniform noise filter. This is about the same amount of grain you'll see on the screen when using this protector.
Resistance to smudging
One very cool thing I noticed is that anti glare protector also seems to be MUCH, MUCH better when it comes to smudges. With ultra clear, I would usually feel a need to wipe the phone after each conversation or a typed SMS. Basically, any contact with skin would cause a mess on the screen. With anti glare, this is still present, but to much lesser extent. I feel that this is a big advantage when compared to ultra clear protector.
Touch sensation and sensitivity
Well, first of all, it does feel slightly different under your finger. Right after applying it, the finger movement across the screen felt rather stiff. There was definitively more friction going on then with ultra clear, but after one or two days of usage, this effect seems to wear off, or you simply get used to it and don't notice it anymore. I can say I have come to actually like this. Oh, and there is no degradation of screen sensitivity that I noticed. I did not feel that I had to push the screen any harder then before, so this is another strong point.
Anti-glare feature
And finally, what would be an anti glare protector review, without comment on the anti glaring From my non scientific tests, the feature works very well. The glaring is indeed much reduced. I would say about 50-60% less, if not even more. Also, when you do get some glare, for example from the direct light above your head, it's much less obtrusive then with ultra-clear or without protector. The effect is subtle, and will not interrupt you from reading things on the device.
Conclusion
All in all, if you can accept the slight grain effect, this is a great thing for people who use Touch HD in bright light or simply feel annoyed with the fact that the default screen protector is so polished you can sometimes see more of your face on it than the screen itself.
So, by sacrificing 5% of visual quality, you can get about 50% more on the usability. I don't regret buy it at all - in fact I only regret not ordering more on my last purchase.
p.s. I have absolutely no connection with Brando, nor I will get anything out of writing this review. I also have to say I have been ordering stuff from them for a while now, and have been very satisfied with their services so far.
That's a very in depth review which I am sure many will find useful.
I have a Brando Ultra Clear and have recently been using my HD in the garden as the weather in the UK has been so hot and sunny recently. I thought it would never work outside because of the bright light but with screen brightness setting on full I could not believe how good it was. No strain on the eye at all with the sun behind or in front. Not sure if this is because of the HTC screen or the Brando Ultra Clear protector - I've not tried it without.
Sounds like Anti Glare is even better from your review but I would say that Ultra Clear is still very useable in bright light.
Hi, been looking for a proper screen protector but haven't really gotten to it yet..
After reading this I'm convinced, I'm gonna get myself one!
...just can seem to locate one in the Netherlands...all shops sell the ultra clear (with anti glare in the descriptive text), but not just an anti glare one.
Anyone?
Thanks
*ordered through shop.brando etc..*
are you going to post some images?
Psygnosis84 said:
are you going to post some images?
Click to expand...
Click to collapse
Not gonna make any promises, but being a photographer, I guess I should
great review...I hate glare! So, I'm ordering one of these Brando anti-glare screen protectors.
Has anyone compared this Brando anti-glare to the Boxwave anti-glare?
As you say above "The effect is sort of like a very, very fine grain pattern across the screen".
The Boxwave has this and it is almost unacceptable (to me) and was wondering if this Brando was any better (clearer) in this department.
Thanks.
zozz said:
Has anyone compared this Brando anti-glare to the Boxwave anti-glare?
As you say above "The effect is sort of like a very, very fine grain pattern across the screen".
The Boxwave has this and it is almost unacceptable (to me) and was wondering if this Brando was any better (clearer) in this department.
Thanks.
Click to expand...
Click to collapse
Hi, I haven't used any Boxwave protectors, so I can't really say, but I am interested to hear from users that tried them.
Personally, I really got used to Brando anti-glare, and I find the device much more comfortable to use in everyday situations. And I really like the fact that the smudging is MUCH less of a problem.
Anyone know where these can be got in the UK?
**EDIT** Nevermind, I got it here - http://shop.brando.com
$3 shipping worldwide, $12 in total = just under £8...
AndyCr15 said:
Anyone know where these can be got in the UK?
**EDIT** Nevermind, I got it here - http://shop.brando.com
$3 shipping worldwide, $12 in total = just under £8...
Click to expand...
Click to collapse
http://www.inkino.co.uk/zen/index.php?main_page=index&cPath=69&zenid=ebdc7d2530edpgsgpjp2v0qbb1 in Tottenham Court Road fit them for you in case you've got a shaky hand
Not sure if they will have anti glare though.
zozz said:
Has anyone compared this Brando anti-glare to the Boxwave anti-glare?
As you say above "The effect is sort of like a very, very fine grain pattern across the screen".
The Boxwave has this and it is almost unacceptable (to me) and was wondering if this Brando was any better (clearer) in this department.
Thanks.
Click to expand...
Click to collapse
Hmm, I actually prefer Boxwave's grain pattern because it gives "texture" to the screen. Yeah it does lower the screen's image quality but overall it's quite nice I reckon
I got mine today, I really like it. It has a matt finish rather than a gloss finish which I prefer the feel of.
Unfortunately it took about 8 attempts to get it on without the edges slightly overlapping and causing the long bubble along the edge and now I think I have some dust under it
Still, it's a great fit, feels great but I have yet to see how well it's anti-glare properties hold up.
Brando, not so good
I have to disagree. At first I was very excited it about it but then... I find it horrible! I was not able to use it. Could not get rid of the bubbles. I think its cut too big! Wash it and nothing but dust gets caught on the backing that sticks to the screen which has some kind of glue like surface. After washing it gets marks all over and dust. I wasted my money. Expensive, not worth it, needs work. I have installed many screen protectors on my touch hd.
Nope, nope, nope... had none of those problems here...
I've had good luck with Brando compared to other protectors.
c6638746 said:
I have to disagree. At first I was very excited it about it but then... I find it horrible! I was not able to use it. Could not get rid of the bubbles. I think its cut too big! Wash it and nothing but dust gets caught on the backing that sticks to the screen which has some kind of glue like surface. After washing it gets marks all over and dust. I wasted my money. Expensive, not worth it, needs work. I have installed many screen protectors on my touch hd.
Click to expand...
Click to collapse
All you need is a steamy bathroom.
I just got the Bodyguarz screenguardz HD. This is there version that has the anti-glare. I have to say that I really like it a lot [recommended!]. More so than ordinary screen protectors. It cuts down on the glare, it is smooth and easy to slide your finger across. Some protectors have that slight tacky/grippy feel [I believe the original bodyguarz screen protectors are like that]. IMO those are not ideal for touchscreens.
Careful though. This is my second set, which Bodyguardz sent me for free. The first set was manufacturered differently and caused a 'halo' effect. This is where the very edges of the protector are not sticking to the black borders of the screen. I notified Bodyguardz about the defect and they sent me a replacement that was manufactured differently, for free!
Here's a link to their website: http://www.bodyguardz.com/screenguardz-htc-evo-3d-cases-screen-protectors-covers-shields-skins-films.html
I will post pics soon, hopefully you'll be able to notice the anti-glare.
I have the equivalent from Zagg (smudge proff, anti-glare), and it took a bit of getting acclimated to it. It makes colors a little more vibrant in my opinion, and sharpens up the screen.
I mainly got it because I wasn't impressed with PhantomSkinz, and I had some gift cards to use up at Best Buy.
Wish I would've seen this before hand, the static cling/ minor adhesive is a little appealing.
Does it really help to have a screen protector on STR? My nook is always inside a case, and always have some finger smudges on the screen, which does not interfere with reading the screen content.
Would it make the screen harder to use, such as in a resistive screen? I know it has IR technology, not resistive lcd, but it is good to know...
I have a screen protector, because I have cats and dogs who're lurking around my nook, and I'd hate to see them scratch the screen. I'm not using any case for it. The film does not affect the touch sensitivity in any way...
thanks for the info, emarusceac.
I can see dogs and cats and stuff being a problem. I just have an old NC sleeve laying around that works. If you can stand the wait, ebay is cheap Turns out the NC and NST width is the same...
emarusceac,
what sort of screen protector are you using?
Hi mh127,
I'm using a basic anti-glare screen film from ebay.
The nst is the first touch screen I have not used one on.
It is perfect now, the matte should hide small scratches, it gets used more lightly than phones/tablets, it is light (less damage if dropped), and it is cheap!
I am going to buy one.
I must warn you that it's VERY hard to apply it smoothly. I mean you'll get some air pouches caused by small particles, those bubbles won't go away no matter what you do. I prefer bubbles to permanent scratches though....
emarusceac said:
I must warn you that it's VERY hard to apply it smoothly. I mean you'll get some air pouches caused by small particles, those bubbles won't go away no matter what you do. I prefer bubbles to permanent scratches though....
Click to expand...
Click to collapse
I ordered one. Was concerned that it would be tough to apply because of the high frame around the screen. Any tips how to apply well? You use a credit card to smooth the film down over the screen?
Oh one more thing. Has anyone tried removing one? Does it change or damage the screen in any way?
I have had several different screen protectors on my NST and none of them caused any damage when I removed them. I would note though that I have read that you must not apply a screen protector to the Glowlight, something about the built in screen protector and its light guide properties. I would also point out the one reason my NST has had multiple screen protectors is because they are so hard to apply without getting bubbles/lint between the screen and the film. The film I have on now I finally got applied without any bubbles/lint in the reading area, so it will hopefully be on there for a while. Make sure you are working in a CLEAN area and take great pains to get it lined up straight before actually applying it to the screen.
The NST doesn't need a screen protector, it really wont do much for the device, but if you really feel like spending the money for it go ahead.
The NSTG already has a protector built in, putting an extra one on would be like putting on an extra pair of latex gloves. It'll offer a little more protection, but it can get to be quite frustrating in terms of lost control. It's advised not to bother with a protector for the NSTG.
Personally unless you know you're going to have your NST in reach of creatures with claws, or lose objects with sharp edges the protective screen will do little for you. Even in those cases it's possible the screen would merely lessen the damage done rather than prevent it out right.
In regards to the NSTG and it's pre-installed screen protector, has anyone actually removed it? I've read lots of reports of people complaining about minor scratches and finger pressure marks causing the light to become very strong on those parts, wondering if removing the screen protector would fix that or whether it's instead a problem with the screen.
Xadious said:
In regards to the NSTG and it's pre-installed screen protector, has anyone actually removed it? I've read lots of reports of people complaining about minor scratches and finger pressure marks causing the light to become very strong on those parts, wondering if removing the screen protector would fix that or whether it's instead a problem with the screen.
Click to expand...
Click to collapse
They claim there is one, I claim they lie as there is no visible edge of one. If there was you wouldn't get the light flares from minor scratches. Adding one may protect the screen but no idea what it would do to the light guide properties of the screen. If you ever have to remove it I'd worry what would happen to the light guide layer.
Because gadgets capabilities/sppecs increase rapidly & prices drop fast too, unless it's expensive I forget about screen protectors if the device is cheapish (got mine cheap) & if it will be outdated in a couple of years. Specially if it's not an outdoor device like my phone. Or if the protector hampers speed / functionality to some degree. Also personally I rarely scratch tab screens unless it's a phone, my phones/tabs all have protectors put on from day one, but not doing my NTSG. YMMV.
So as many of you may have noticed during your uses with the nook in either bright lighting, in the car, or straight up outside (to cold for that here), the glare on the screen can get quite bad. So i was looking online for a decent antiglare for the NT or NC and i stumbled across this:
http://www.amazon.com/gp/product/B004MC4KF8/ref=fb_lfb_prodpg_0
A cheap, 2 pack with stylus, antiglare screen protectors. Now im not going to claim its the best one on the market, but if your looking for a cheap one, then go with this. It has been working very good on my NT, and it makes the screen feel silky smooth, not to mention severely reduces the nasty grease lines from my fingers.
Also, the stylus was actually surprisingly good. I've used numerous ones (cheap ones, for sure, but still multiple) styluses and this is easily the best one I've found. Nice and solid with a reactive tip that doesn't grip the screen or seem like it will fall off.
I can second this I actually purchased the same thing like a week ago. I love my protector its real nice and the stylus is pretty good. A little too sensitive with the app drawer (it likes to open apps when trying to turn the app pages) but other than that its perfect!
Just received this today and I must concur...a quality screen protector and stylus! I purchased my wife the Caseen case also and we've been really happy with it as well.
I purchased the official B&N anti-glare screen protector for $20 (eek!). I got it mainly because my daughter somehow manages to get food and who-knows-what-else on the screen. B&N says not to use moisture when cleaning the screen, but that's the only way to get the crud off. So, I got the B&N protector.
Anyway, despite comments online about people destroying both sheets in the process of installing them, I installed mine without any problems. First I made sure the screen was completely clean with absolutely no dust on it. Then I peeled back just an inch or so of the removable film, pushed the top edge of the sheet to where the case meets the screen, then slowly peeled back more as I pushed the sheet onto the screen, by bending the sheet as I worked my way down the screen. No air bubbles. No dust. No dirt. It's perfect and it looks like it will last forever.
I've got the glareshatter screen protector, its fantastic. That metal stylus is fantastic too. Do yourself a favor and hit up your local auto parts store and pick up a microfiber cloth, keep it on hand for cleaning. Also a little white vinegar on the microfiber does the job nicely.
Sent from my BNTV250 using xda premium
Hey Guys,, i am thinking of getting the above,,, i read in the forum some of the screen protector is causing harm to the screen....
is this case with this screen protector also???
Can somebody show some light on it.
Cheers!!!!!!!!!!
I bought the Import version of the Caseen Glareshatter for under $10 on ebay. Never owned the Caseen's standard protector, so I can't compare.
This is what I like:
Easy to install - it's about 2mm narrower than the screen
The feel is about perfect
Glare is definitely reduced though you still have to compensate when it's extreme
The fingerprints are there but only vivilbe from an angle with the screen off. They don't affect the visibility with the screen on.
Thing I don't like:
Makes the screen darker which is especially noticeable on the white background. I had to increase the brightness about 10% to compensate for it.
Only had for a couple of days but I am very happy so far.
Any idea where to get those in Europe? I could only find shops in the US carrying them (on ****ingly high shipping rates).
I trusted you guys and got the Glareshatter screen protectors. They really make a huge difference. Installation is really easy, just be sure to clean the screen first.
so is this glareshatter version truly the best then?
Just alittle weary on how it effects the clarity. Since some of those amazon reviews mention it.
Citizen Toxie, I was a little worried about that, too. But honestly, it's really hard to tell there's even a screen protector installed. I haven't tried any other brands, because I've really been satisfied with the import Glareshatters.
So you haven't seen it make the screen darker then? I usually keep my screen at 50%, so I'm hoping it looks the same.
If so, I will probably just grab that one.
I had my system brightness set to 30% before installing the screen protector, and I haven't changed it since.
gotcha. thanks.
guessing you grabbed the import one off ebay then?
http://www.ebay.com/itm/caseen-Nook...?pt=US_Tablet_Accessories&hash=item4cfc1c766b
nevermind. all good now.
I actually got mine off Amazon in a packaged deal with a stylus. They're also available on Caseen's official website I think, so see where you're able to get the best deal after shipping and everything.
Only 11 bux for 2 of the Glareshatters and a stylus on amazon. Pretty sweet deal.. ordering one now!
I asked someone who had used an antiglare screen protector if he recommended it and he said no because it significantly darkened the screen.
I went into B&N because my tablet was dead in the water, would not turn on at all and had to be swapped out. I asked to get an anti-glare screen protector there and he pulled one out and said they are normally $20, but because they came with a cloth inside that apparently damaged the screen or the screen protector confused that they were giving them away... Not sure if this is true or still available if so, but just thought I'd share. Made me happy!
Interesting. Wondering if that's worth a trip.
Decided I'm just going with the B&N one, since I don't really need the anti-glare.
Has anyone came across a good privacy screen protector, or something that cuts down the viewing angle quite a bit?
The Product:
http://www.amazon.com/gp/product/B006QG47YW/ref=oh_o00_s00_i00_details
The Review:
Well, like many TF201 owners, I suffer from disappointment with the glossy finish on the Prime's screen. It's hard to show off your tablet/laptop hybrid when you open it up and it's covered in oil from our fingers. Luckily, Acase has a solution.
This screen protector does exactly what it is described to do:
1-Protects the screen (yes, it's "gorilla glass" but that doesn't mean it's beyond extra protection)
2- applies a matte finish to the screen
3- drastically decreases the presence of fingerprints
I can officially say that this product was applied by ME (and I have no professional training in applying screen protectors) and the application process went well with no dirt/dust/bubbles.
They ship the screen protectors in a box which is nice because it helps protect from any bending that could occur en route.
The only con I can think of at this point is the same con you'll get on any matte screen protector, the screen does lose a little clarity. In my opinion, however, the loss in clarity is not enough to even care about.
In conclusion, if you want a solution to the glossy screen and the presence of fingerprints, I highly recommend this product. I am pleased with my purchase and the product is working the way it should.
The Pictures:
http://dl.dropbox.com/u/31210960/Pictures/20120308_093925.jpg
http://dl.dropbox.com/u/31210960/Pictures/20120308_093957.jpg
http://dl.dropbox.com/u/31210960/Pictures/20120308_094029.jpg
Looks great. Sounds good too. I'm curious how the screen feels, same as without the protector? Just curious if it hinders sliding the fingers much.
Sent from my Transformer Prime TF201 using Tapatalk
I wonder what the longevity is of this anti-glare screen protector.
In my experience after a few months the texture gets worn smooth in spots from repeated finger rubbing. Also after a few weeks they get "gummy" and lose some of their fingerprint resistance while at the same time becoming a bit more difficult to clean.
Also, how does this skin work with styli?
I am currently switching between the Griffin GC16040 and the Jot Classic. Does a skin like this one reduce the sensitivity of a stylus significantly? The Jot in particular is very much affected even by smooth screen protectors.
almightywhacko said:
Also, how does this skin work with styli?
I am currently switching between the Griffin GC16040 and the Jot Classic. Does a skin like this one reduce the sensitivity of a stylus significantly? The Jot in particular is very much affected even by smooth screen protectors.
Click to expand...
Click to collapse
I'm writing this with the Acase stylus and anti-glare protector. The stylus seems to be just as responsive now just like before applying the screen protector. The protector does take away some brightness; however, I'm not having to clean the screen every 5 minutes. I highly recommend it.
SirFenwick said:
Looks great. Sounds good too. I'm curious how the screen feels, same as without the protector? Just curious if it hinders sliding the fingers much.
Sent from my Transformer Prime TF201 using Tapatalk
Click to expand...
Click to collapse
In my opinion, I like how my finger slides better with this screen protector than without it.
My hypothesis is this:
Since the screen protector repels oils, I'm assuming that there isn't a layer of accumulated oil between the finger and the screen, thus allowing for better movement upon the screen.
Also, my Minisuit stylus works quite well with it. I would say it works just as well as without a screen protector.
I'm pleased with this purchase.
bscotth said:
In my opinion, I like how my finger slides better with this screen protector than without it.
My hypothesis is this:
Since the screen protector repels oils, I'm assuming that there isn't a layer of accumulated oil between the finger and the screen, thus allowing for better movement upon the screen.
Also, my Minisuit stylus works quite well with it. I would say it works just as well as without a screen protector.
I'm pleased with this purchase.
Click to expand...
Click to collapse
This type of screen protector doesn't repel oil at all. In fact over time most of them will absorb oils from your hand.
The reason that your finger slides easy is that the surface is textured which reduces the surface area that you finger actually makes contact with, which in turn reduces friction.
Incidentally the texture is the same reason why fingerprints show up less easily, since some of the oils from your fingers will slip below the highest surfaces of the screen protector so that you don't see it.
However like I said in my other post, textured screen protectors tend to get worn smooth after a few months of regular use, which makes me wonder how long this one will last.
Keep us posted!
Thanks for the review.. though about a week too late!
I ordered the minisuit anti-glare / anti-fingerprint.. guess we'll see if it's much different than the Acase stuff when it comes in in a few days.