Related
I googled how to reset my phone back to factory settings and they gave me this link
"[STOCK ROM] Odin3 One-Click Downloader"
(cant link links)
i misread that it was for the captivate, and i went through with all the directions.
now my phone keeps flashing an AT&T bootscreen and i cant get it in recovery mode..
help?
same here... that odin thing isn't working. Im just stuck at the vibrant boot screen. I know how to get into download mode but my pc or ODin doesnt recognize that i have my phone in. it's suppose to light up yellow or something. the tar files and all of that stuff is so confusing.
nevermind, i found the Odin program for the samsung vibrant and re did it.. but i still have BOTH at&t boot screen at the tmobile vibrant boot screen.. anyone know how to get rid of that? it would be much appreciated thanks!
http://forum.xda-developers.com/showthread.php?t=741027
where did u find it.. please share..
Edit: NVM..
stepinmyworld said:
same here... that odin thing isn't working. Im just stuck at the vibrant boot screen. I know how to get into download mode but my pc or ODin doesnt recognize that i have my phone in. it's suppose to light up yellow or something. the tar files and all of that stuff is so confusing.
Click to expand...
Click to collapse
You may have tried this but these are the steps that eventually worked for me.
1. Put your phone in download mode by plugging it in and then holding Vol Up+Down and Power. As SOON as the screen goes black release power but NOT Vol Up+Down.
2. Launch Odin
3. Unplug your phone.
4. Load the pit and pda files into odin.
5. Plug your phone back in. You should now see one of the small blocks turn yellow and show you the com port. If not, something is wrong with your drivers.
6. Click start. If it flashes, great. If it hangs at File analasys then repeat 1-5.
6a. If Odin hangs at cache.rfs then move on to 6b.
6b. Unplug your phone (Odin will say it was removed) and remove the battery. DO NOT SHUT DOWN ODIN!!!!!!
6c. Put the battery back in and plug it back into your computer and put it back into download mode using step 1.
6d. Press start on Odin and it should now flash.
Again, this worked for me, it may have been a fluke and I'm not willing to try it again. Good luck!!!
Does not boot!
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
setzer715 said:
You may have tried this but these are the steps that eventually worked for me.
1. Put your phone in download mode by plugging it in and then holding Vol Up+Down and Power. As SOON as the screen goes black release power but NOT Vol Up+Down.
2. Launch Odin
3. Unplug your phone.
4. Load the pit and pda files into odin.
5. Plug your phone back in. You should now see one of the small blocks turn yellow and show you the com port. If not, something is wrong with your drivers.
6. Click start. If it flashes, great. If it hangs at File analasys then repeat 1-5.
6a. If Odin hangs at cache.rfs then move on to 6b.
6b. Unplug your phone (Odin will say it was removed) and remove the battery. DO NOT SHUT DOWN ODIN!!!!!!
6c. Put the battery back in and plug it back into your computer and put it back into download mode using step 1.
6d. Press start on Odin and it should now flash.
Again, this worked for me, it may have been a fluke and I'm not willing to try it again. Good luck!!!
Click to expand...
Click to collapse
i am completely lost when it comes to ODIN. I need to know the exact program to use. I have Odin Multi Downloader v4.03.. but it keeps giving me file path error and stuff. I have the right drivers i think because it does recognize my phone. im just so confused with this rar tar stuff. I would pay someone 20 dollars through paypal if they can walk me through this.
stepinmyworld said:
i am completely lost when it comes to ODIN. I need to know the exact program to use. I have Odin Multi Downloader v4.03.. but it keeps giving me file path error and stuff. I have the right drivers i think because it does recognize my phone. im just so confused with this rar tar stuff. I would pay someone 20 dollars through paypal if they can walk me through this.
Click to expand...
Click to collapse
I don't want your money, but if you PM me I will try to type up a detailed how to.
mffu said:
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
Click to expand...
Click to collapse
What have you done to put it in download mode? You should power off your phone, plug it into your computer. It should then enter the charge mode where you see a picture of your battery being charged (or if you were like me and screwed up somewhere you may see a little picture of a phone, computer and yellow triangle in between them). If you get either of those then press and hold all three VOL up, VOL down and power. AS SOON AS the screen goes black release ONLY Power and it should go into download mode.
If you plug your phone into your computer (powered off) and nothing happens then you just be bricked. Call TMO and play dumb and hopefully get a replacement.
Ok,
The_Chrome_Coyote really helped me!!!! Thank you so much and im back up and running. There was something missing from the original tutorial, not that we should be spoon fed but I didn't have the WinRAR program on my pc and didn't know I needed to extract anything. I was looking for exe. for it to be a program and just open it. It's a little more complicated than that. I added my additions in BOLD
The_Chrome_Coyote's Original post to me:
Odin isnt that hard, its just REALLY picky about working.
Firstly you need to download the Samsung drivers for your OS which can be found:
http://forum.xda-developers.com/showthread.php?t=728929
added:
Second you need to make sure you download WinRAR x86 (32 bit) 3.93 (google it and you should be able to get it) otherwise if your pc doesn't have a program to recognize rar and tar files, you are out of luck.
then read this thread from JAC:
http://forum.xda-developers.com/showthread.php?t=734475
1. Now, Extract ODIN from its .rar and place the .exe on your desktop
2. Extract the .pit file from its.rar and place that on your desktop
3. Place the JFD .tar file on your desktop but DO NOT EXTRACT
Now you can use ODIN
4. Start ODIN Odin3. [Android + SLP], through ODIN select the .pit file
5. Hit "PDA" button, and through ODIN select the .tar file
6. Plug your TURNED OFF PHONE into the USB cable
7. Wait for the Battery/ charging indicator to start
8. HOLD VOL UP+ VOL DOWN+ POWER, as soon as the screen goes black RELEASE POWER, and continue to HOLD VOL UP+ VOL DOWN Until it enters download mode. Which should happen quickly and looks like a men at work highway sign.
9. If a COM port has turned Yellow in ODIN, then the device has been recognized. If it hasnt, unplug and plug your phone back in.
10. Dont select any options other than whats set at default.
11. Hit Start and be patient, takes me maybe 5 minutes to get back up and running.
NOTE: If you do not see a blue progress bar on the phone's screen after a minute;
11a. Turn your phone off by pulling the battery.
11b. CLOSE ODIN
11c. Start at step 4 again.
ODIN needs to be open and ready to flash before the phone is plugged in, in my experience. Its very picking about this, and not everyone has this issue, but I did and following all these steps helped me flash my phone more times than I can count the other day haha.
Hope this helped! and your $20, donate it to Wes, JAC, or Eugene to keep them making great stuff for our phone.
Reply With Quote
Thank you thank you thank you
mffu said:
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
Click to expand...
Click to collapse
Same thing happened to mine when i tried odin. Now all i get sometime when it come on. are 7 rows of text that seems to be a code on screen in amber. Ishipped back 2 samsung. Since t-mobile won't take it after 14 days.
ok I screwed up guys.
I installed ROM manager from the market, flashed clockwork, it asked me if I wanted to partition and I said yes.
Now I just get a black screen at boot. I've managed to run odin and it says success. But I still just get a black screen after boot.
Little help?
I do have to say that if YOU DO NOT KNOW HOW TO EXTRACT A COMPRESSED FILE (RAR, ZIP,ETC) YOU HAVE NO BUSINESS FLASHING YOU'RE PHONE!! Odin or otherwise.
I am not being mean but at least stick to update.zip files flashed through recovery and make sure you read reviews of other users first, and understand the instructions completely.
Sent from my SGH-T959 using Tapatalk
daddysays said:
I do have to say that if YOU DO NOT KNOW HOW TO EXTRACT A COMPRESSED FILE (RAR, ZIP,ETC) YOU HAVE NO BUSINESS FLASHING YOU'RE PHONE!! Odin or otherwise.
I am not being mean but at least stick to update.zip files flashed through recovery and make sure you read reviews of other users first, and understand the instructions completely.
Sent from my SGH-T959 using Tapatalk
Click to expand...
Click to collapse
First: everyone was a noob at one time, so simmer down.
Second: Pleast post an update.zip that will make my phone work.
Cannot get past Galaxy S boot screen
I was using clockwork recovery installed through an update.zip file on my sd card. everything was working fine for about a day and then when i powered my phone off the next day and powered it back on it would not boot up past the Galaxy S screen. it goes to the Galaxy S screen and then goes blank but my hard keys stay lit up while my lcd is completely blank. I tried using the Odin method described in this thread and it seemed like it was going to work but i still cannot get past the boot screen. please help. willing to donate if needed
jmoney1017 said:
I was using clockwork recovery installed through an update.zip file on my sd card. everything was working fine for about a day and then when i powered my phone off the next day and powered it back on it would not boot up past the Galaxy S screen. it goes to the Galaxy S screen and then goes blank but my hard keys stay lit up while my lcd is completely blank. I tried using the Odin method described in this thread and it seemed like it was going to work but i still cannot get past the boot screen. please help. willing to donate if needed
Click to expand...
Click to collapse
If you can see the samsung logo you are fine. Load up recovery and try a full wipe first. If that fails then you can odin back to stock and root again.
Sent from my SGH-T959 using XDA App
1. If you have questions, there is a q and a forum for this device!!!!!!
2. THIS IS THE DEV PART OF THE FORUM. IE FOR DEVS POSTING STUFF FOR THE PHONE!!!!!
3. Learn how to Google. Not that hard. Example, you don't know what the *.rar extension is. GOOGLE IT!! Google knows everything.
4. If you don't have basic android or computer skills, don't try anything stupid. You do have a chance to brick your phone, even the pros like cyanogen have bricked their phones.
5. Don't offer cash for someone to fix your phone. Keep it in qna and some one will help you. Save your cash for the development that work hard on making these things work.
6. Can a mod please move this thread to qna.
7. THE MOST IMPORTANT THING. USE THE SEARCH FINCTION BUILT ONTO THE FORUMS. IT WILL SAVE YOU TIME AND THEN YOU WILL NOT LOOK LIKE NOOBS THAT JUST GOT THIS PHONE BECAUSE IT HAD AVITAR IN THE BOX!!!!!
Sent from my SGH-T959 using XDA App
cache.fs problem in odin
setzer715 said:
What have you done to put it in download mode? You should power off your phone, plug it into your computer. It should then enter the charge mode where you see a picture of your battery being charged (or if you were like me and screwed up somewhere you may see a little picture of a phone, computer and yellow triangle in between them). If you get either of those then press and hold all three VOL up, VOL down and power. AS SOON AS the screen goes black release ONLY Power and it should go into download mode.
If you plug your phone into your computer (powered off) and nothing happens then you just be bricked. Call TMO and play dumb and hopefully get a replacement.
Click to expand...
Click to collapse
I FOUND A SOLUTION TO THE CACHE.RFS PROBLEM!!
http://www.fractionalphones.com/?p=121
I flashed clock mod recovery into my phone
When I reboot to recovery from the app or by rebooting
It goes to android recovery mode and it also has
Yellow words saying that theres been a checksum error
What does this mean?
And how can I fix this?
Thanks in advance
I think it has something to do with partition sdcard with clockwork mod. I had that exact same error message on mine too. But since than I got a new vibrant, flashed multiple roms using clockwork mod and my recovery boot is still normal.It no longer shows checksum error.
Sent from my SGH-T959 using XDA App
Odin
T959 (US T-Mobile version of the Galaxy S) Firmware that can be flashed through ODIN to restore all partitions to the way your phone was shipped to you.
WARNING!!! THIS WILL WIPE ANY DATA ON YOUR DEVICE, IT WILL REPLACE YOUR BASEBAND, KERNEL, RECOVERY AND OS.
DOWNLOADS:
ODIN application – Download
512 PIT file -Download
T-Mobile Vibrant JFD Image – Download
USB Drivers from the Samsung Galaxy S – 32 Bit Windows Download \ 64 Bit Windows Download
INSTRUCTIONS:
1.Your Device must be in DOWNLOAD mode to use ODIN.
2.Get your phone into DOWNLOAD mode by turning off your phone and plugging it in. Wait for the green charging screen. Hold Volume Up, Volume down, and Power. Let go of power as soon as the screen goes black. A yellow digging Android should be on the screen. This may take a few tries to get it right. (Alternate Method if you have ADB access : use the command ‘adb reboot download’). ALso Another way is Vibrant plugged into usb on the computer hold Vol/UP/Down together and the Home key @ the bottom ,so when u pwr up let go of the pwr button and have the other down u cant miss it it goes everytime....
3. Launch ODIN, then disconnect/reconnect your phone via USB. It should then say a COM port right under top-right box. (Issues detecting your device on a COM port? Try connecting your phone before starting ODIN, and don’t do the disconnect\reconnect. It’s a finicky application.)
4.In ODIN, load each file with its corresponding field..PIT,PDA,CSC etc. (In this case we just use the PDA and PIT).
5.Don’t check anything else, the other two boxes should be checked by default (Auto Reboot and Reset Time)
6.Hit “start.” Be patient!
NOTE: COM3 worked fine for me. COM should not matter as long as you are using the correct drivers.
Finally we get some U.S love from Samsung firmwares.
For those looking for the Nandroid method, it is in the post below but only recovers system, data, and cache.Not your kernel/recovery or BASEBAND/RADIO (Modem.bin)
Thx to all helping work on the Vibrant. Especially Youneek, Scepterr, MS_Guru, Wes Garner, rhcp0112345, and anyone else I may have forgotten.
Yeah that what happened to me too I was tring
To partition my sd card and that started happening
Thanks montana free ima try it when I get home! One last
Question so do we always wipe before every flashing?
Just asking because on bionix rom they say it does it on its own
Just wondering we ll thanks again for your help!
Yeah on Sombonix Roms I think he has that all incorporated in every rom...
I do mines once in while blue moon, I Never have a issue,when I flash so just be careful all these Vibrants phone do different things.... Side note it odd how sum Vibrants cant handle voodoooo lagfix as a example.... let me how it goes man....
Yeah For sure
But man sucks that I have to stay in late
MontanaFree said:
Yeah on Sombonix Roms I think he has that all incorporated in every rom...
I do mines once in while blue moon, I Never have a issue,when I flash so just be careful all these Vibrants phone do different things.... Side note it odd how sum Vibrants cant handle voodoooo lagfix as a example.... let me how it goes man....
Click to expand...
Click to collapse
One More question will it be the stock j16 or the the one before?
I tryed flashing a rom without disabling voodoo and know my phone wont even turn on. Any help please!!!!
ireiricky said:
I tryed flashing a rom without disabling voodoo and know my phone wont even turn on. Any help please!!!!
Click to expand...
Click to collapse
If you look couple threads down, you'll see my thread, and I am having the same problem. Slightly different cause, but of the same nature, and the exact same problem. I have not had any real help yet, but I have been scouring the forums here. And I think the only option, if none of the button combinations work, as they don't seem to for me, and you're getting a complete brick, is perhaps the usb jig resistor method... but even that I don't think is 100% because some of the people who created the guides on how to make the jig resistor said it only worked for softbrick, not total brick like our cases. Unless someone can verify otherwise...
Thanks for the reply man i don't know what to do man i spent $400 0n this phone there must be a way but no luck on google either
ireiricky said:
I tryed flashing a rom without disabling voodoo and know my phone wont even turn on. Any help please!!!!
Click to expand...
Click to collapse
Try this. Take your sim card, microsd and battery out. Leave battery out for a few minutes.
Open odin and load with the 512 pit and Jfd tar.
Plug one end of usb cable into computer only
take your vibrant with everything still out of it
hold down both vol buttons (vol up and down) and never let go
do not touch power
while holding down both volume buttons plug in your usb cable into the phone with the other end previously in the computer...do all this while holding down volume buttons and dont let go
now grab your battery with your free hand and while still holding down the vol buttons now plug in your battery
if all goes well your.phone should go into download mode at which pt you can let go of volume buttons.
If this doesnt work you can maybe try the jig if your bootloader is intact
also since you were messing with voodoo you might need to first flash eugenes froyo tbat doesnt brick...im not too sure on this so ask around and look it up.
You need this first of all (Froyo that does not brick)
http://eb-productions.proboards.com/index.cgi?board=samsungsgs&action=display&thread=8
jordanjf86 said:
1. Download Eugenes 'Froyo that does not brick' file.
2. Extract the files.
3. Open Odin, plug in your phone, then put it into download mode.
4. load the PIT file in appropriate area.
5. load the .tar file in the PDA area.
6. DO NOT check 're-partition'.
7. Click start, let it finish. Your phone will load and reboot into stock recovery. It will error out again. DONT panic! This is what's supposed to happen.
8. Now, pull your battery.
9. Download the 'True stock 2.1 firmware for the vibrant'.
10. Extract the files.
11. Once again, open Odin, plug in your phone, put into download mode.
12. Load the PIT file into the appropriate area and the .tar in the PDA area.
13. THIS TIME you want to check the 're-partition' box.
14. Now click start, let it finish, and this time your phone will load up just fine! BAM!
Click to expand...
Click to collapse
Don't forget to thank :]
iv'e tryied that i read somewhere that it's a hard brick
Then try accessing download mode by first, removing the sd card, sim, and battery, second, plugging in the usb cable, third, holding down the two buttons on the side of the phone, and finally, while holding down those two buttons, inserting the battery.
I havee tried that mothod many times no luck just a blank screen
Then commit a fraud and send it back to T-Mobile saying it suddenly stopped working.
Or if you prefer a wild card you can use a JIG
http://forum.xda-developers.com/showthread.php?t=819551
Edit: Never mind it will not work for you. Sorry :/
Edit 2: The phone does not even turn the buttons on??
no nothing turns on at all no power but when i put it to charge it heats up but no battery screen
Yea, take it to T-Mobile and get it replaced. I got mine switched at T-Mobile once, and it would only boot to the custom Nexus animation....the lady still swapped it out. It all depends on the rep, if they won't switch it, go to a different location. Eventually you'll find someone.
i don't think thats possible seeing as im in Canada bought it off ebay
take it to a phone expert. he will flash a bootloader to your phone.
Sent from my SGH-T959 using XDA App
Today was I was watching the video on how to flash darky's resurrection.zip rom,
then zi tried flashing it to my wifes Vibrant , I folloeed the video step by step. I used odin I get the green light saying the phone passed then when it reboots it get stuck on the galaxyi900 screen and it doesnt boot up. Ive flashed the thing with odin at least 10 -15 times after and still no luck, it keeps getting stuck at the opening. My wife says if I dont fix it I have to buy her a new phone. Someone save me please!!!!!!
LMAO........... yeah my wife said the same thing...... sounds like you may have not disabled the voodoo lagfix before the flash.
you will probably need to flash back to stock. I am not sure what is stock on this phone I am going to assume it is the same Vibrant.
If you can get into recovery and you did have voodoo installed disable it. If not you can disable it on your phone and copy the folder and then load it into the internal sd card messed up phone and replace the old folder.
Then you may need to use Eugenes froyo that does not brick as a intermediary flash. if you can Odin that (use Odin 1.7) then when it you flash it do not check the repartition box. When it is beginning to reboot, do not let it fully reboot, pull the battery. Then Redo the Odin as described below:
Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Leave all check boxes the way they are. Check the repartition box.
Click the PIT button and select the 512.pit file
Click the PDA button and select T959JFD.tar and then click Start
When it is done you will be back at stock. Then Root the phone and go from there.
still getting the loop! this phone is jacked up. I can enter download without pressing the power button, cause it turns on and off itself
My phone just keeps flashing the opening Samsung galaxy s gt-i9000
Oh good I don't know the pit or .tar files sorry
Sent from my SGH-T959 using XDA App
Omar50 said:
still getting the loop! this phone is jacked up. I can enter download without pressing the power button, cause it turns on and off itself
Click to expand...
Click to collapse
take the battery out, wait 30 seconds, plug the usb cable in, and then hold both the volume buttons and slide the battery in. Presto! Download mode.
This has saved me numerous times lol. Then just flash JDF like oka said
i dont have problem entering download mode. When I flash with odin I get a pass on it. but when the phone reboots it stays on the opening screen go on and off
i download the heimdall suite 1.1.1 and the necessary windows program to run it. when i plug my phone into download mode heimdall start button isn't accessable. am i missing something?
figured out hoew to get access to start button, dont use partition. now it gets error on recognizing the device. Im so frustrated right now I need a smoke!!!!!!!
Omar50 said:
figured out hoew to get access to start button, dont use partition. now it gets error on recognizing the device. Im so frustrated right now I need a smoke!!!!!!!
Click to expand...
Click to collapse
Depends on what you smoke........
You may need the pit 513 file instead of the pit 512 file, these mapping files are a bit different and it may be a cause. Hard to know without seeing the phone
Also you could do a full wipe if you can get into recovery, wipe cache, phone reset and dalvik wipe (in advanced) then try That may work better for you.
It is recoverable.......... and also the best way to get your wife to calm down......... a romantic restaurant with candle light........ you go on Tuesday and she goes on Thursday........
Hope you get it fixed..........
thanks for the support but no luck I tried 513 pit nothing my phone still wont boot up I still get the opening screen then it shuts off and starts again.
im really having a bad day now i tried flashing the stock rom 2.2 with odin now the phone wont even power on! i guess its really a brick. i bought myself a paper weight
Hello All,
First, let me say how much I've enjoyed reading this Forum and how much I LOVED my TMobile Samsung Vibrant 3G. While it worked for a long time running Froyo 2.2 with a Bionix Next-Gen V2 ROM, it was fantastic, but lately the microphone had been dying (I sounded more and more muffled no matter what I did). So I flashed up to ICS and installed Chimera to see if that might help. While the phone ran beautifully except for several apps that were rather wonky, I was getting more and more muffled.
So the other day I decided to restore my Nandroid backup, however when I flashed back I got stuck on the Vibrant boot screen. No matter what I do, I can't seem to get to Recovery.
How do I get back to Recovery from this? I have never used Odin, the only time I've ever hooked the phone up to the computer was when I originally flashed from Eclair to Froyo many moons ago. So please let me know if I'm missing something.
Any assistance would be greatly appreciated!
You made a mistake when you tried to restore a 2.2 based backup from ICS base ROM. Now you must Odin to stock, its not that hard. First you will need to download the Odin program. I'm assuming you have device drivers on your PC but double check. Next you need 2 files, the 512 pit and jfd firmware file. Once you have those files you need to get in download mode.
I will link a thread with files and directions. http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
samsgun357 short and sweet as always
samsgun357 said:
You made a mistake when you tried to restore a 2.2 based backup from ICS base ROM. Now you must Odin to stock, its not that hard. First you will need to download the Odin program. I'm assuming you have device drivers on your PC but double check. Next you need 2 files, the 512 pit and jfd firmware file. Once you have those files you need to get in download mode.
I will link a thread with files and directions. http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
Click to expand...
Click to collapse
OK I installed Odin and the necessary files and drivers, I plugged in the phone, but when I try to turn it on into Download Mode the Vibrant doesn't respond. There's just the little spinning light in the center of the screen. Odin doesn't recognize the phone either.
Anything else I can do?
Odin won't recognize unless you are in DL mode. I linked a video, I know it says captivate. Don't worry about the mod etc just follow it to get in download mode.
https://www.youtube.com/watch?v=qXMqLpnTPh0&feature=youtube_gdata_player
I approve this message.
If this won't play just search download mode vibrant on YouTube.
samsgun357 said:
Odin won't recognize unless you are in DL mode. I linked a video, I know it says captivate. Don't worry about the mod etc just follow it to get in download mode.
https://www.youtube.com/watch?v=qXMqLpnTPh0&feature=youtube_gdata_player
I approve this message.
If this won't play just search download mode vibrant on YouTube.
Click to expand...
Click to collapse
OK watched the video, but 2 things:
-when I try to boot into Recovery it gets stuck on the Vibrant Samsung initial splash screen and never moves, even when holding down the 3 buttons;
-this video assumes I can access the phone to install the fix or anything else. I can't, it just stays stuck in the splash screen;
-I tried holding down the 3 buttons and simultaneously plugging in the USB cable, and still nothing but the splash screen;
-is there any way to turn on the device while hooked into the computer so Odin or something else can use the necessary files to turn it on and make it accessible?
Thanks all for your patience and advice, it's much appreciated. I LOVE this little phone and really want to heal her!
Hi,
I think you have tried to go to recovery mode using 3 button combo. But in order to use ODIN device has to be in DOWNLOAD MODE which can be done using following steps
1)start off with phone turned off
2)press down volume up, and volume down at same time, and never let go until you get into download mode. DON'T touch the power button
3) while holding down both volume buttons get your usb cable which is connected to your computer
4)plug in the usb cable into your phone, while you still hold down both up/down volume buttons at same time. Don't touch the power button.
5)As soon as you plug your usb cable into your phone, the phone will instantly go into Download mode.
6)You may now release the volume buttons
Click to expand...
Click to collapse
hope this will help you to go on
tc
NOTE: here is a link I found. Just take a look http://www.ithinkdiff.com/how-to-access-download-and-recovery-mode-in-samsung-vibrant/
OK we are trying to get download mode not recovery. Your phone must be off for download mode. If it flashes vibrant screen you have gone to far and something is wrong. I specifically said pay no attention to the mod in video. Regardless I think you might need a jig to get in download mode.
I approve this message.
OK, noob error (smacks head), I kept saying Recovery Mode when what I needed was DL Mode, my sincerest apologies.
I got into DL Mode finally by holding down the Volume buttons (not the Power button), then plugging in the USB cable. The Vibrant promptly went into DL mode. Odin recognized the phone and off we went. It's now back to Stock Eclair (yuck).
So next question: am I rooted or do I have to do that all over again? And if so, what's the fastest way to do it so I can flash to the ROMs I knew and loved?
Lastly, a great big THANK YOU to samsgun357 & haarsh for all your assistance, you guys ROCK! :good:
No you are not rooted after using Odin to go back to stock. Glad you got it buddy! Now use this guide to get root and cwm recovery. Option b is probably what you want
http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
Glad you are successfully ODINed and you are in perfect position to make things BETTER
Still the device is not rooted as samsgun357 said. but no worries it is a simple process to get rooted and go ahead. I will post an video and hope it will also ease up your task
tc and its a pleasure to help you
Happy Flashing :good:
Yep, got it rooted and flashed Cyanogen7, then flashed up to an ICS ROM (started with Chimera but it's a tad wonky so flashed over to Euphoria, we'll see how that goes).
That said, the microphone is still sounding very muffled, so I think it's a hardware issue. I was due for an upgrade anyway so I picked up the Samsung 4G Blaze (nice since the Vibrant I had was the 3G). So right now I'm just having fun exploring Android on the Vibrant while I read up on how to root and improve the Blaze.
I will miss this little phone though, it was light and super fast and agile, perfectly sized, especially compared to the mini-tablets coming out lately like the Samsung SIII and LG L9 or HTC One. I prefer smaller phones, so the Blaze fits the bill right now even though it's heavier than my old Vibrant.
Thanks again for everyone's assistance, VERY much appreciated! :good:
Hey guys,
I'm having the same problem w/ my phone (see img).
I can't get out of the little loading pinwheel.
I've tried all the prescribed methods in this thread.
Thoughts?
Sorry, also, I can't get to DL or the splash page. When I turn the phone on, it goes directly to the spinning pinwheel.
check this thread : http://forum.xda-developers.com/showthread.php?t=848737
Gingerbread Bootloaders
Key Maps
For Recovery - Lower Volume Key + Power Button
For Download - Upper Volume Key + Power Button
Froyo Bootloader
Key Maps
For Recovery - Both Volume Keys + Power Button
For Download - Both Volume Keys and Connect USB Cable
Click to expand...
Click to collapse
tc
hoss9009 said:
Sorry, also, I can't get to DL or the splash page. When I turn the phone on, it goes directly to the spinning pinwheel.
Click to expand...
Click to collapse
Download mode IS what you need to use Odin a get back to stock.
The above post shows the button combo for DL mode and recovery based on which bootloaders you're running (thanks haarsh). If you haven't flashed GB boots, you have froyo boots.
Now make sure you have the correct Odin files and drivers on your PC.
The goal here is to get power to the phone, while holding button combo, from the PC.
Do a battery pull/replace. Plug USB into computer
While holding your button combo (see above) plug the phone in.
Hopefully you see DL mode
Also try pulling battery, plug USB in PC and phone
While holding button combo, pop the battery back in.
This can be tricky sometimes so don't give up.
OK. Let me backup and give you more info.
So sorry...
I rooted, but was unable to download ROM manager from the Store (im assuming bc it was running Froyo).
I was able to get CMW to install via update.zip. Once installed the phone was going directly into recovery when asked (3 button method). It would go into the Anroid recovery, first and then from continually installing CMW, go into CMW.
From there i installed a CM10 nightly.
Install went fine, but no mobile data connection. I went back to CMW and restored the original ROM, rebooted and am stuck w/ the pinwheel.
I can't get into to download mode AT ALL. I've tried the various button methods with no luck.
From what I did, I can assume that 2.1 IS installed on the phone.
Thoughts?
Thank you so much for the help.
Well the issue you have was caused by going back to a 2.1 or 2.2 build from cm10 through cwm. You should have used Odin to get back to stock.
If you can't get in DL mode manually you will need to buy a DL jig. You can get them from www.mobiletechvideos.com also from amazon I think. You can also make one yourself, just search USB download jig, you should find it.
Sent from my SGH-T959 using xda premium
samsgun357 said:
Well the issue you have was caused by going back to a 2.1 or 2.2 build from cm10 through cwm. You should have used Odin to get back to stock.
If you can't get in DL mode manually you will need to buy a DL jig. You can get them from www.mobiletechvideos.com also from amazon I think. You can also make one yourself, just search USB download jig, you should find it.
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
Ok.. nothing at against your advice, but do they really work?
Yes they do. Look them up, I'm sure there are testimonials.
Sent from my SGH-T959 using xda premium