Related
Hello everyone. I have a question about the current state of my Vibrant. Coming from a G1, I just upgraded to the Vibrant and have been loving since. I rooted my device, installed Clockwork Recovery, and flashed a new Rom. I decided to switch back to the stock rom but now when I turn on my Vibrant, it just sits at the Vibrant Samsung boot screen... Here are the steps I did up until this point:
1. Starting from the Stock T-Mobile rom, I applied Root update zip but booting into Recovery Mode (Holding down the volume Up/Down buttons and then pressing the Power button).
2. Installed Clockwork Recovery, and then did a Nandroid Backup.
3. Using Clockwork, I installed Eugene's Vibrant7 rom (I left create ROM Backup and Wipe Data options checked)
4. Vibrant7 rom flashed successfully but decided to switch back. So I used Clockwork to boot into manual recovery mode, selected Nandroid and then Restore
After it finished the Restore, it now sits at the Vibrant Samsung boot screen everytime I power it up... I'm thinking I should have not have used the Nandroid Restore to revert back to the stock ROM (unless I'm totally mistaken, I never used Clockwork Recovery before and have flash roms before with my G1).
At this point, could I just reflash back to the stock firmwire using ODIN (Directions from this thread [ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working) in the Vibrant/Android Development section). Would that take care of my problem or is my phone currently 'bricked' or SOL?
Thanks in advance for any help or clarification
yeah just odin back to stock... Read the directions carefully
this exact same thing is happening to me. I have tried to follow the instructions to odin. but when I hold volume down and power it just keeps rebooting to the vibrant page. but if I hold volume up and down and power I can get into recovery but non of the options fix my problem. Am I screwed or am I doing something wrong.
i'm having the same problem...stuck on boot screen
i'm on the bell network, are there instructions on how to use odin to fix my phone?
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
flashed a sgh t959 with a galaxy s i9ooo kernel oops
hi im stuck in manual mode and when i try to boot the screen shows two different galaxys s screens then goes back to manual mode and i cant get into down load mode it just goes back two manual mode was trying to root used wrong file i think im screwed i flash with oden and used i9000xxxhph tar file
Same with me, I think I soft bricked my vibrant, so I tried to restore to stock rom using odin. Odin detects it and runs stock rom just fine, but once it was restarting, the phone would not still boot up and would stay stuck at the vibrant samsung screen. I tried other roms such as froyo no brick, and i9000 stock rom also, would not boot also, just stuck at the samsung screen. What do I do? Odin works through the process fine though......why isnt it fixed?
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
yes yes yes! your mistake was using the power button! Lol.
FUTURE NOTE: if you upgrade to any gingerbread roms.... new bootloaders are required. If your JIG didnt get you into download mode before...... then it isn't working right. Once your into the the new Bootloaders for gingerbread, the sequence is........ HOLD VOL UP and POWER until you trigger DL mode. No USB required.... DO NOT FLASH NEW BOOTLOADERS WITHOUT A WORKING JIG IN YOUR POSSESION. TEST IT BEFORE YOU FLASH. I had...... an experiance.... lol
Not working
ParaMount33 said:
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
Click to expand...
Click to collapse
I tried all the instruction still stuck on Vibrant logo if i connect cable the Loader pix cums but doesnt load or show me battery image what to do now? also Odin doesnt recognize neither i can go to download mode!!!!!
If you can get in DL mode you are halfway there, next make sure you have correct drivers. Uninstall current drivers and reinstall correct drivers. Odin can be funny sometimes, you might need a new USB cable, try every USB port as well.
You can also use the All In One (AIO) program to get drivers and back to stock. If you are having issues with Odin try this
http://forum.xda-developers.com/showthread.php?p=11358713
sent from the depths of helly bean
hi,
Once i gt a prob restoring. But then I re-flashed the ROM which the nandroid backup was taken and then in CWM selected advance and gave restore data option(as i remember).. (it was not full restore with system..b/c I flashed system separately)
You can go back to stock using ODIN .. as mentioned by Daddy_617 previously.
tc
Also if Odin doesn't work for you try Heimdall. I've seen post where this has worked for others.
Vibrant stuck on "Vibrant Samsung"
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
I tried this but the say thing keeps happening ... really need help
so i was wanting to load the bionix rom, so i did a nandroid on my last rom. bionix was "okay" so i decided i wanted to go back to my eugene rom.
so i use rom manager to load the old image, and while doing so it gives me some error that i should report to rom manager. i cant exactly say what it was. so i told it to reboot, but now im back on bionix, and all my apps are crashing. i cant get into the launcher or anything. so getting to rom manager was out of the question.
so i call my friend who says i probably need to load a stock image, which thats fine whatever. so i do some googlin' and i come across this method forum.xda-developers.com/showthread.php?t=734475 (new user..cant post links)
i try to follow the directions best i could. ive never used odin before. so for the "pit" i select the "samsung galaxy s firmware flasher" (which was the only file my computer let me pick) and for the pda part i selected t959uvjd.tar file they also had listed. also the instructions said i didnt need to select the other boxes (phone, csc, etc)
so i put it in recovery, hit start, after a few minutes my screen just shows the little android guy and a caution sign. odin still says "file analysis" and its been like this for about 20 minutes...
so....where do i go now? please be as descriptive as possible..apparently im still a lil green at all this
How did you get into recovery mode? Are you sure it wasn't download mode? Did you use the hardware way with vol up +dwn and power or did you use adb
http://lmgtfy.com/?q=did+i+brick+my+vibrant
splayer7 said:
How did you get into recovery mode? Are you sure it wasn't download mode? Did you use the hardware way with vol up +dwn and power or did you use adb
Click to expand...
Click to collapse
i used adb to get into recovery. i figured out its not bricked. i restarted it and its doing the same thing. by that i mean it boots up, but all my apps are crashing still..so i guess i gotta figure out how to actually use odin to mount the stock image.
before you use odin, make sure you are hardware unlocked. I bricked one that was hardware locked using odin. Read, read, read.
The android guy and the caution sign is download mode, what you need to flash odin. Odin can be finicky. Once your in dl mode on your phone, unplug it from the usb cable, then launch odin and load the files. Reconnect your pc and you should see a com port light up in odin. If it doesn't light up, disconnect and reconnect again, or relaunch odin, reload the files and then reconnect the usb. Sometimes it takes some playing with it to find the right combo to make it work. After that its happy flashing time, you should see the progress under the selected com port in odin, kick back and wait for the reboot.
Be sure you have the GalaxyS drivers loaded on your pc too, your comp will never see your phone in dl mode without the drivers
Sent from my SGH-T959 + bionix 1.3 (= sexiness) using XDA App
BossDj said:
The android guy and the caution sign is download mode, what you need to flash odin. Odin can be finicky. Once your in dl mode on your phone, unplug it from the usb cable, then launch odin and load the files. Reconnect your pc and you should see a com port light up in odin. If it doesn't light up, disconnect and reconnect again, or relaunch odin, reload the files and then reconnect the usb. Sometimes it takes some playing with it to find the right combo to make it work. After that its happy flashing time, you should see the progress under the selected com port in odin, kick back and wait for the reboot.
Be sure you have the GalaxyS drivers loaded on your pc too, your comp will never see your phone in dl mode without the drivers
Sent from my SGH-T959 + bionix 1.3 (= sexiness) using XDA App
Click to expand...
Click to collapse
Download mode for me is an android guy is IN a triangular caution sign & says "downloading..."
Stock recovery with the MENU button pressed shows me an android standing next to a caution sign. Think the op should clarify.
All~G1 said:
Download mode for me is an android guy is IN a triangular caution sign & says "downloading..."
Stock recovery with the MENU button pressed shows me an android standing next to a caution sign. Think the op should clarify.
Click to expand...
Click to collapse
I do remember the little andriod guy and the caution sign from the one and only time i got stuck in stock recovery. I can't boot to it with any button combo, but the first time I tried to make an update.zip myself, well, yeah i got rebooted to stock recovery. My mind went to dl mode when I read the op, as thats what I have the most experience using, and luckily can boot to that way easily on my phone. I think you are correct G1, op may be booting to recovery mode and attempting to flash, when dl mode is whats necessary.
Sent from my SGH-T959 (+ bionix 1.3 + kingklicks kernel = sexiness) using XDA App
BossDj said:
The android guy and the caution sign is download mode, what you need to flash odin. Odin can be finicky. Once your in dl mode on your phone, unplug it from the usb cable, then launch odin and load the files. Reconnect your pc and you should see a com port light up in odin. If it doesn't light up, disconnect and reconnect again, or relaunch odin, reload the files and then reconnect the usb. Sometimes it takes some playing with it to find the right combo to make it work. After that its happy flashing time, you should see the progress under the selected com port in odin, kick back and wait for the reboot.
Be sure you have the GalaxyS drivers loaded on your pc too, your comp will never see your phone in dl mode without the drivers
Sent from my SGH-T959 + bionix 1.3 (= sexiness) using XDA App
Click to expand...
Click to collapse
well origionally i was not in download mode, i only saw the screen i was talking about once, but i ended up actually getting it into download mode and using odin tried flashing the stock roms. it would hang everytime. the only rom i was able to get working was eugenes froyo port. its incredibly buggy and a whole lot of things dont work correctly on my phone. i tried the unlocking method to see if that helps, but my phone is really fighting everything i do right now.
but i do have a replacement coming, so im just gonna deal with a phone that wigs out whenever i try to do stuff for a few days.
After flashing Macnut R12 and Eugene's a13 kernel, my Vibrant will only boot to the "Galaxy S I9000" screen, but nothing further. The screen doesn't go black and no buttons flash, the phone just doesn't boot past that screen. I can enter recovery and download mode, and can use clockwork mod recovery, but I'm not sure what my next steps should be. Should I attempt to use Odin (Bricked my first Vibrant with that, though that one was HW-Locked), or is there some other way to fix this?
Scratch that, now my Vibrant boot-loops (Boots to galaxy S I9000 screen then restarts), and I can't enter recovery. Starting to freak out a bit, hoping download mode works... Any help would be appreciated.
Generic112 said:
Scratch that, now my Vibrant boot-loops (Boots to galaxy S I9000 screen then restarts), and I can't enter recovery. Starting to freak out a bit, hoping download mode works... Any help would be appreciated.
Click to expand...
Click to collapse
Gmail me [email protected]
Sent from my SGH-T959 using XDA App
Here is a couple of methods to get into download mode. Once you get to download mode, follow the directions later in my post...
First Method
1) Pull the battery, sim card, and sd card.
2) Reinsert battery but do not press any buttons.
3) Plug into usb that is connected to your computer. If something shows up on the screen (charging logo) then you should be golden.
4) Hold the vol up, vol down, and power until the screen comes on, immediately release the power button but not the other two. You should be in dl mode.
Second Method
1) Another method that seems to work for some people is to pull the battery, sim, sd card.
2) Reinsert battery and hold both volume buttons but do not press power button.
3) Then plug in usb. The phone should boot into download.
Third Method
1) You will need the samsung ADB drivers installed for your phone and ADB.
Samsung Drivers for 32 bit Windows: http://files.androidspin.com/downlo...=SAMSUNG_USB_Driver_for_Mobile_Phones_x86.exe
Samsung Drivers for 64 bit Windows: http://files.androidspin.com/downlo...ung/vibrant/&file=usb_drivers_GalaxyS_x64.zip
2) Remove sim card and sd-card. Remove the battery.
3) Hold buttons vol up, vol down, and power.
4) While holding down those 3 buttons put the battery back in and keep holding all 3 buttons until the vibrant disappears and reappears. Once it reappears, release all 3 buttons.
5) Now connect your phone to your pc via USB cable.
6) Open a cmd prompt and navigate to the folder with ADB and type "ADB REBOOT DOWNLOAD" caps are not necessary.
7) Your phone will reboot into the download mode.
Once in download mode
Download the files in the linked thread and follow the directions there or the ones below.
Odin and Files Needed Available Here: http://forum.xda-developers.com/showthread.php?t=734475
1) Open Odin and verify that one of the Com ports shows a device connected. If it doesn't try using a different usb port.
2) Load the .pit and pda files. It should be pretty obvious how to do that once you are in Odin.
3) Make sure that the option to partition is unchecked. The other two options should be checked.
4) Hit start and wait.
5) Your phone will restart when Odin is done and you will be good to go.
Also, you might have to build the usb jig. It is guaranteed to get you into download mode. Here is a link to that thread:
http://forum.xda-developers.com/showthread.php?t=819551
Also, if you would like I can use remote log in to your computer and do it for you. Send me a pm or email: [email protected]
Ok, Download mode (Via Volume + and - and plugging in usb) works flawlessly, but I'm still unsure of how to go about using Odin to fix this problem. Should I go the "Froyo that doesn't brick" downgrading route, or should I just flash JFD? And to the above poster, I won't have access to the internet for a couple hours after this post, so I can't email you right away. If I can't fix the problem later today, I will certainly contact you for some assistance.
Thanks for the guide, I'm just worried about what to flash. I've seen people praise Eugene's downgrading method for fixing most any problem (Froyo that doesn't brick to JFD), but I'm very much an Odin novice, and I'd hate to let it tear the life out of yet another phone (Though thankfully this one isn't HW-Locked). Also, does flashing JFD through Odin touch the SBL or anything that could affect my phone's ability to access recovery/download mode through hardware methods? I've heard that the JI6 OTA update fixes the 3-Button mode, but I'm unsure of whether or not JFD breaks that (Though I assume it doesn't). Anyway, thanks for the help, sorry if I don't post back soon, have to leave the house for a few hours, and I'm stuck with my old phone until I can fix my Vibrant.
One last question, should I use the Odin in the link, or an updated version (If one exists, I believe Odin3 1.70 is the latest and I don't know used in that thread)? Last time I used Odin it froze and killed my HW-Locked Vibrant.
Generic112 said:
Thanks for the guide, I'm just worried about what to flash. I've seen people praise Eugene's downgrading method for fixing most any problem (Froyo that doesn't brick to JFD), but I'm very much an Odin novice, and I'd hate to let it tear the life out of yet another phone (Though thankfully this one isn't HW-Locked). Also, does flashing JFD through Odin touch the SBL or anything that could affect my phone's ability to access recovery/download mode through hardware methods? I've heard that the JI6 OTA update fixes the 3-Button mode, but I'm unsure of whether or not JFD breaks that (Though I assume it doesn't). Anyway, thanks for the help, sorry if I don't post back soon, have to leave the house for a few hours, and I'm stuck with my old phone until I can fix my Vibrant.
One last question, should I use the Odin in the link, or an updated version (If one exists, I believe Odin3 1.70 is the latest and I don't know used in that thread)? Last time I used Odin it froze and killed my HW-Locked Vibrant.
Click to expand...
Click to collapse
Thank you for pointing out that the linked thread has the old Odin. I attached the new Odin 1.7 in this post. The other files (pit and pda) in that thread will work fine. Once you get booted into that ROM (Stock JFD) just re-root, install CWM recovery and reflash with a ROM of your choice.
Just wanted to say that Odin ran successfully for me, and I now have my Vibrant back in working order. Thanks for the help (and that nifty little guide).
Generic112 said:
Just wanted to say that Odin ran successfully for me, and I now have my Vibrant back in working order. Thanks for the help (and that nifty little guide).
Click to expand...
Click to collapse
You are welcome. Glad you got it working again...
Hello,
Please read the WHOLE post, as I've already done hours of XDA research and could not come across a similar situation.
I'm afraid that after months of flashing away, I've finally bricked my phone (for good).
I was ODINing back to stock from CM7, but something went wrong and ODIN froze. Not thinking it was a big deal, I took out the USB cable out.
This prompted my phone to not respond at all (no power, no recovery combo). However, searching around XDA, I found the way to enter download mode (through the plug in USB then plug in battery while holding volume buttons trick). I flashed the Froyo bootloaders, thinking that my bootloader was corrupted. This made the phone turn on to the "VIBRANT" screen, but nothing else. I still could not get into recovery mode through the 3 button combo.
I then proceeded to ODIN a JFD image, along with the 512 pit file. This put my phone into a non-responsive (read: no buttons work) state again, and so I flashed the Froyo bootloaders again. Once again, I was stuck at the "VIBRANT" screen.
Then I ODINed a JFD image without repartitioning with the 512 pit file. This continued to put my phone at the "VIBRANT" screen.
What went wrong?
I read up something about JTAG service; is this what I need? (From what I read, if you can access download mode, you're good to go, so I'm not sure if I "hard-bricked" my phone)
THANKS so much...
if you were on cm7 it was 2 button
3 button is for recovery
battery out\ reinsert battery
press volumeup\down insert usb cable.... downlod should appear
odin to stock
Sugartibbs said:
if you were on cm7 it was 2 button
3 button is for recovery
battery out\ reinsert battery
press volumeup\down insert usb cable.... downlod should appear
odin to stock
Click to expand...
Click to collapse
I can get into recovery, and I can ODIN to stock, but my phone is continually bricked--in fact, if I ODIN to stock, my phone doesn't turn on. (I know I'm doing it correctly because I've done it successfully before)
R you ona 3g samsung vibrant?
Sugartibbs said:
R you ona 3g samsung vibrant?
Click to expand...
Click to collapse
Yes, I have the original 3G Samsung Vibrant.
Sorry, but i had to ask, when you come out of odin and have green pass you should come out in recovery and either reboot or have an error message, yet you have the vibrant logo, is reboot checked? If all ese fails Aio toolbox, then you know pit, pda and if necessary drivers are correct. and not corrupted.
This is gonna take a bit more searching but your gonna have to find Eugene's froyo that doesn't brick. Odin that and then Odin back to stock maybe you can pm him for the files.
Sent from my SGH-T959 using XDA App
Sugartibbs said:
Sorry, but i had to ask, when you come out of odin and have green pass you should come out in recovery and either reboot or have an error message, yet you have the vibrant logo, is reboot checked? If all ese fails Aio toolbox, then you know pit, pda and if necessary drivers are correct. and not corrupted.
Click to expand...
Click to collapse
Thanks for all your help!
I figured out the problem--apparently the PDA file was corrupted. Internet here is spotty, so I guess it corrupted while downloading. I flashed the re-downloaded PDA file, and was able to un-brick my phone.
Hello All,
First, let me say how much I've enjoyed reading this Forum and how much I LOVED my TMobile Samsung Vibrant 3G. While it worked for a long time running Froyo 2.2 with a Bionix Next-Gen V2 ROM, it was fantastic, but lately the microphone had been dying (I sounded more and more muffled no matter what I did). So I flashed up to ICS and installed Chimera to see if that might help. While the phone ran beautifully except for several apps that were rather wonky, I was getting more and more muffled.
So the other day I decided to restore my Nandroid backup, however when I flashed back I got stuck on the Vibrant boot screen. No matter what I do, I can't seem to get to Recovery.
How do I get back to Recovery from this? I have never used Odin, the only time I've ever hooked the phone up to the computer was when I originally flashed from Eclair to Froyo many moons ago. So please let me know if I'm missing something.
Any assistance would be greatly appreciated!
You made a mistake when you tried to restore a 2.2 based backup from ICS base ROM. Now you must Odin to stock, its not that hard. First you will need to download the Odin program. I'm assuming you have device drivers on your PC but double check. Next you need 2 files, the 512 pit and jfd firmware file. Once you have those files you need to get in download mode.
I will link a thread with files and directions. http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
samsgun357 short and sweet as always
samsgun357 said:
You made a mistake when you tried to restore a 2.2 based backup from ICS base ROM. Now you must Odin to stock, its not that hard. First you will need to download the Odin program. I'm assuming you have device drivers on your PC but double check. Next you need 2 files, the 512 pit and jfd firmware file. Once you have those files you need to get in download mode.
I will link a thread with files and directions. http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
Click to expand...
Click to collapse
OK I installed Odin and the necessary files and drivers, I plugged in the phone, but when I try to turn it on into Download Mode the Vibrant doesn't respond. There's just the little spinning light in the center of the screen. Odin doesn't recognize the phone either.
Anything else I can do?
Odin won't recognize unless you are in DL mode. I linked a video, I know it says captivate. Don't worry about the mod etc just follow it to get in download mode.
https://www.youtube.com/watch?v=qXMqLpnTPh0&feature=youtube_gdata_player
I approve this message.
If this won't play just search download mode vibrant on YouTube.
samsgun357 said:
Odin won't recognize unless you are in DL mode. I linked a video, I know it says captivate. Don't worry about the mod etc just follow it to get in download mode.
https://www.youtube.com/watch?v=qXMqLpnTPh0&feature=youtube_gdata_player
I approve this message.
If this won't play just search download mode vibrant on YouTube.
Click to expand...
Click to collapse
OK watched the video, but 2 things:
-when I try to boot into Recovery it gets stuck on the Vibrant Samsung initial splash screen and never moves, even when holding down the 3 buttons;
-this video assumes I can access the phone to install the fix or anything else. I can't, it just stays stuck in the splash screen;
-I tried holding down the 3 buttons and simultaneously plugging in the USB cable, and still nothing but the splash screen;
-is there any way to turn on the device while hooked into the computer so Odin or something else can use the necessary files to turn it on and make it accessible?
Thanks all for your patience and advice, it's much appreciated. I LOVE this little phone and really want to heal her!
Hi,
I think you have tried to go to recovery mode using 3 button combo. But in order to use ODIN device has to be in DOWNLOAD MODE which can be done using following steps
1)start off with phone turned off
2)press down volume up, and volume down at same time, and never let go until you get into download mode. DON'T touch the power button
3) while holding down both volume buttons get your usb cable which is connected to your computer
4)plug in the usb cable into your phone, while you still hold down both up/down volume buttons at same time. Don't touch the power button.
5)As soon as you plug your usb cable into your phone, the phone will instantly go into Download mode.
6)You may now release the volume buttons
Click to expand...
Click to collapse
hope this will help you to go on
tc
NOTE: here is a link I found. Just take a look http://www.ithinkdiff.com/how-to-access-download-and-recovery-mode-in-samsung-vibrant/
OK we are trying to get download mode not recovery. Your phone must be off for download mode. If it flashes vibrant screen you have gone to far and something is wrong. I specifically said pay no attention to the mod in video. Regardless I think you might need a jig to get in download mode.
I approve this message.
OK, noob error (smacks head), I kept saying Recovery Mode when what I needed was DL Mode, my sincerest apologies.
I got into DL Mode finally by holding down the Volume buttons (not the Power button), then plugging in the USB cable. The Vibrant promptly went into DL mode. Odin recognized the phone and off we went. It's now back to Stock Eclair (yuck).
So next question: am I rooted or do I have to do that all over again? And if so, what's the fastest way to do it so I can flash to the ROMs I knew and loved?
Lastly, a great big THANK YOU to samsgun357 & haarsh for all your assistance, you guys ROCK! :good:
No you are not rooted after using Odin to go back to stock. Glad you got it buddy! Now use this guide to get root and cwm recovery. Option b is probably what you want
http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
Glad you are successfully ODINed and you are in perfect position to make things BETTER
Still the device is not rooted as samsgun357 said. but no worries it is a simple process to get rooted and go ahead. I will post an video and hope it will also ease up your task
tc and its a pleasure to help you
Happy Flashing :good:
Yep, got it rooted and flashed Cyanogen7, then flashed up to an ICS ROM (started with Chimera but it's a tad wonky so flashed over to Euphoria, we'll see how that goes).
That said, the microphone is still sounding very muffled, so I think it's a hardware issue. I was due for an upgrade anyway so I picked up the Samsung 4G Blaze (nice since the Vibrant I had was the 3G). So right now I'm just having fun exploring Android on the Vibrant while I read up on how to root and improve the Blaze.
I will miss this little phone though, it was light and super fast and agile, perfectly sized, especially compared to the mini-tablets coming out lately like the Samsung SIII and LG L9 or HTC One. I prefer smaller phones, so the Blaze fits the bill right now even though it's heavier than my old Vibrant.
Thanks again for everyone's assistance, VERY much appreciated! :good:
Hey guys,
I'm having the same problem w/ my phone (see img).
I can't get out of the little loading pinwheel.
I've tried all the prescribed methods in this thread.
Thoughts?
Sorry, also, I can't get to DL or the splash page. When I turn the phone on, it goes directly to the spinning pinwheel.
check this thread : http://forum.xda-developers.com/showthread.php?t=848737
Gingerbread Bootloaders
Key Maps
For Recovery - Lower Volume Key + Power Button
For Download - Upper Volume Key + Power Button
Froyo Bootloader
Key Maps
For Recovery - Both Volume Keys + Power Button
For Download - Both Volume Keys and Connect USB Cable
Click to expand...
Click to collapse
tc
hoss9009 said:
Sorry, also, I can't get to DL or the splash page. When I turn the phone on, it goes directly to the spinning pinwheel.
Click to expand...
Click to collapse
Download mode IS what you need to use Odin a get back to stock.
The above post shows the button combo for DL mode and recovery based on which bootloaders you're running (thanks haarsh). If you haven't flashed GB boots, you have froyo boots.
Now make sure you have the correct Odin files and drivers on your PC.
The goal here is to get power to the phone, while holding button combo, from the PC.
Do a battery pull/replace. Plug USB into computer
While holding your button combo (see above) plug the phone in.
Hopefully you see DL mode
Also try pulling battery, plug USB in PC and phone
While holding button combo, pop the battery back in.
This can be tricky sometimes so don't give up.
OK. Let me backup and give you more info.
So sorry...
I rooted, but was unable to download ROM manager from the Store (im assuming bc it was running Froyo).
I was able to get CMW to install via update.zip. Once installed the phone was going directly into recovery when asked (3 button method). It would go into the Anroid recovery, first and then from continually installing CMW, go into CMW.
From there i installed a CM10 nightly.
Install went fine, but no mobile data connection. I went back to CMW and restored the original ROM, rebooted and am stuck w/ the pinwheel.
I can't get into to download mode AT ALL. I've tried the various button methods with no luck.
From what I did, I can assume that 2.1 IS installed on the phone.
Thoughts?
Thank you so much for the help.
Well the issue you have was caused by going back to a 2.1 or 2.2 build from cm10 through cwm. You should have used Odin to get back to stock.
If you can't get in DL mode manually you will need to buy a DL jig. You can get them from www.mobiletechvideos.com also from amazon I think. You can also make one yourself, just search USB download jig, you should find it.
Sent from my SGH-T959 using xda premium
samsgun357 said:
Well the issue you have was caused by going back to a 2.1 or 2.2 build from cm10 through cwm. You should have used Odin to get back to stock.
If you can't get in DL mode manually you will need to buy a DL jig. You can get them from www.mobiletechvideos.com also from amazon I think. You can also make one yourself, just search USB download jig, you should find it.
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
Ok.. nothing at against your advice, but do they really work?
Yes they do. Look them up, I'm sure there are testimonials.
Sent from my SGH-T959 using xda premium