[Review with Photos] HHI TF201 Anti-Fingerprint, Anti-Glare Screen Protector - Asus Eee Pad Transformer Prime

I'm updating the original post because I have now received and applied this screen protector. You can see the photos and my comments here:
https://plus.google.com/photos/105537586944716449433/albums/5696831693307582225
Overall, it's pretty darn good. The fingerprint problem is practically non-existent now and the Prime's screen brightness more than makes up for the slight reduction in sharpness the anti-glare screen causes - even on Auto-Adjust Brightness. I can attest to the fact, that with some care and warm soapy water, the screen are removable and reusable. And they're pretty cheap to buy on Amazon.
Some small complaints:
* The punchouts for the camera and light sensor are completely punched out and more that one person will mess up their install trying to remove them. Even after installation they are a bit unsightly.
* The was no cardboard applicator despite what the instructions say but I didn't use one anyway. And the included lint free cloth frays at the edges with some use and leaves particles behind. Try a coffee filter instead.
* It's likely you will have one side that doesn't quite adhere to the screen along the edge if you handle it from that edge. This can cause you to inadvertantly unpeel the screen from time to time. But I've had that with every screen protector I've had what isn't part of a cover.
If you have any questions ask away and I will try to help.

denverbuckeye said:
Ordered the three pack of this one:
HHI Asus Transformer Prime TF201 Anti-Fingerprint, Anti-Glare, Matte Finished Screen Protector
Anyone have any experiences with this brand?
Click to expand...
Click to collapse
I dont but one of the biggest gripes i have right now (and mirrored by others) is the insatiable appetite this screen has for finger prints. And the glossiness.
I want a matte finish so i can see it clearly outside and not worry about blinding myself or anyone ....Can anyone who has put on matte screen protectors chime in on how happy they were...if the colors were muted too much (yes, glossy = gorgeous) and if the tacileness changed when sliding fingers?

While I have never personally used a matte screen protector, the general consensus is that they do dull the screen a bit and the texture a bit.
Sent from my Droid using Tapatalk

denverbuckeye said:
Ordered the three pack of this one:
HHI Asus Transformer Prime TF201 Anti-Fingerprint, Anti-Glare, Matte Finished Screen Protector
Anyone have any experiences with this brand?
Click to expand...
Click to collapse
Thanks added to my:
Ultimate Transformer PRIME TF201 Accessory Guide
http://forum.xda-developers.com/showthread.php?p=20013463#post20013463

Denver: Could you PM me when you get them or post an edit? i HATE how glossy this screen is...while trying to watch/play games while the wife is after christmas shopping is painful even with super IPS+ turned on. matte although not perfect would lessen how often i see my double chin

joepic said:
Thanks added to my:
Ultimate Transformer PRIME TF201 Accessory Guide
http://forum.xda-developers.com/showthread.php?p=20013463#post20013463
Click to expand...
Click to collapse
we get it, you have a
Ultimate Transformer PRIME TF201 Accessory Guide
http://forum.xda-developers.com/show...3#post20013463

My boyfriend bought this same protector for his TF101 (although it was a 1-pack, not a 3-pack) and he's still happy with it. I personally think that the antiglare protectors make the screen look cheap and plasticky and would rather wipe off prints than have my screen look less clear, so I buy the crystal-clear ones (I have an order from the same company on Amazon for the crystal 3-pack).
Like a lot of you, though, he wanted to reduce glare and prints so it has worked well for him. He had a very problematic application but in a three-pack you get more tries, and all of the bubbles except for one or two settled out over time. The included stylus is a piece of junk.

biggem001 said:
we get it, you have a
Ultimate Transformer PRIME TF201 Accessory Guide
http://forum.xda-developers.com/show...3#post20013463
Click to expand...
Click to collapse
Thanks for this, this has been popping up all over the place. While I appreciate the time and effort that went into this guide, half the stuff needs to be removed as its for the original transformer and could easily confuse someone.

for people who have it, how is the texture? my biggest gripe with screen protectors (next to the fact that i can never get them on clean with no bubbles) is that they have a more sticky texture compared to bare glass.
the coating on the prime's screen makes fingerprint cleaning super easy though for what it's worth.

adiliyo said:
for people who have it, how is the texture? my biggest gripe with screen protectors (next to the fact that i can never get them on clean with no bubbles) is that they have a more sticky texture compared to bare glass.
the coating on the prime's screen makes fingerprint cleaning super easy though for what it's worth.
Click to expand...
Click to collapse
To me, the TF101 one (the matte one) feels like the LCD screen of my laptop, the several-generations-ago Macbook Pro. Non-glossy, a little plasticky but not grippy/a problem for swiping a finger.

watsaname said:
While I have never personally used a matte screen protector, the general consensus is that they do dull the screen a bit and the texture a bit.
Sent from my Droid using Tapatalk
Click to expand...
Click to collapse
While that is true, I'll gladly trade some brightness for the matte smooth non-sticky texture and anti-glare.

codyco83 said:
While I appreciate the time and effort that went into this guide, half the stuff needs to be removed as its for the original transformer and could easily confuse someone.
Click to expand...
Click to collapse
I guess you didn't read the first couple of lines of the guide...
DISCLAIMER: Some of the items listed below (case, screen protector, etc.) are for the Eee Pad Transformer TF101. They are here to give you an idea for something you may not have know about. The manufactures have NOT made a PRIME TF201 version yet. I will update the list with TF201 product when it becomes available.

joepic said:
I guess you didn't read the first couple of lines of the guide...
DISCLAIMER: Some of the items listed below (case, screen protector, etc.) are for the Eee Pad Transformer TF101. They are here to give you an idea for something you may not have know about. The manufactures have NOT made a PRIME TF201 version yet. I will update the list with TF201 product when it becomes available.
Click to expand...
Click to collapse
That doesn't mean it isn't still misleading.... because it is.
Did anyone actually receive this screen protector yet?? Hows the fit?

Wannagotopopeyes said:
That doesn't mean it isn't still misleading.... because it is.
Did anyone actually receive this screen protector yet?? Hows the fit?
Click to expand...
Click to collapse
Doesn't release til the 6th. I ordered one too, I'll update as to how well also. P.S. Skinomi's dry install screen protector is effin garbage...

I've used both on other devices. The matte skin does dull things up a bit, but if you want anti-glare that is the only solution you have. It also helps with finger prints a little. The clear, is just a screen protector which you will still get the glare and some finger prints. It just boils down to preference. I happen to HATE glare, so I usually stick with the matte. I'll just increase brightness by one notch and I'll be fine.

This screen protector seems to be in stock now on Amazon, anyone receive theirs yet??
I'm still hesitant to order one but I want to get rid of these damn fingerprints

biggem001 said:
we get it, you have a
Ultimate Transformer PRIME TF201 Accessory Guide
http://forum.xda-developers.com/show...3#post20013463
Click to expand...
Click to collapse
Wait did I miss something, you mean we have an
Ultimate Transformer PRIME TF201 Accessory Guide
http://forum.xda-developers.com/show...3#post20013463[/QUOTE]

**** I had no idea! One common place to get ALL my Tf201 accessories? Thanks!!!!!!!!!!

joepic said:
I guess you didn't read the first couple of lines of the guide...
DISCLAIMER: Some of the items listed below (case, screen protector, etc.) are for the Eee Pad Transformer TF101. They are here to give you an idea for something you may not have know about. The manufactures have NOT made a PRIME TF201 version yet. I will update the list with TF201 product when it becomes available.
Click to expand...
Click to collapse
In Codyco's defense... You do get really annoying with that. If you're going to be that repetitive about it, make sure it's a damnedly good formatted post, and right now it's not.

As for the OP. I had a Steinheill (SGP) antiglare/matte screen protector on my Samsung GT10.1 and I LOVED it.
I read my text books on my tablet so I am reading on it more than I am consuming video, and I could absolutely not stand at the glare on the screen. The screen protector even let me read the tablet outside without staring at the trees and their leaves behind me.
That being said, there was a slight degradation in screen quality but the antiglare tradeoff made it *much* more than worth it. Plus it makes swiping across the screen buttery smooth. However, that was a top quality screen protector. Ymmv with a cheaper brand.
I utterly cannot get the people who lambast them, as they have to deal with ridiculous amounts of reflections.

Related

Skinomi, clearfreak or wait for a better screen protector?

Hi, i am getting my transformer soon (i hope) and i would like to know your opinion on those screen protectors, i seen a lot of skinomi and clear freak thread but i am also wondering about the price, those 2 turn around 20 bucks each and im used to (12$ for 2 realooks protectors (for a phone though)) and i seen a couple of threads of people scratching the skinomi when trying to install it.. so i were wondering:
Is the +/- 20$ price is the price for those screen protector or are they gonna go down? (early adopter fee?)
I am really scared of a wet application method, is there dry screen protector out there?
Does any of you actually know if zagg or realook intend to release screen protectors for the transformer?
And finally, is there another tablet out there with the EXACT dimension for a screen protector (seen a couple for the iconia here and there but none for the transformer....)
Thanks a lot!
Funny you should ask, I just posted this in the other skinomi thread
If you're looking for anti-glare I'd go with ViewGuard. It's a hard plastic and thicker than the wet application options. I have one on my laptop and it dramatically reduces the reflectiveness and it hasn't reduced the touch sensitivity on it at all. It's what I plan on getting for mine when it gets here. Yes, I have a mutli-touch capacitive screen on my laptop.
Ok,does the dimension fit the transformer ?(or a little bigger?)
just get my eeepad, I know the case/sleeve is required, do I really need a screen protector?
tks
benmyers2941 said:
Funny you should ask, I just posted this in the other skinomi thread
If you're looking for anti-glare I'd go with ViewGuard. It's a hard plastic and thicker than the wet application options. I have one on my laptop and it dramatically reduces the reflectiveness and it hasn't reduced the touch sensitivity on it at all. It's what I plan on getting for mine when it gets here. Yes, I have a mutli-touch capacitive screen on my laptop.
Click to expand...
Click to collapse
Exactly what I was looking for. Thanks for the post
~DC
benmyers2941 said:
Funny you should ask, I just posted this in the other skinomi thread
If you're looking for anti-glare I'd go with ViewGuard. It's a hard plastic and thicker than the wet application options. I have one on my laptop and it dramatically reduces the reflectiveness and it hasn't reduced the touch sensitivity on it at all. It's what I plan on getting for mine when it gets here. Yes, I have a mutli-touch capacitive screen on my laptop.
Click to expand...
Click to collapse
Now we have to find the size that will fit th TF, even though the screen is 8.5 X 5.5 the glass is 10X7. The closest size they list is for 12.1 4X3 aspect @ 9.72 X 7.28 which would have to be trimmed. I contacted them about custom sizes.
~DC
roy2004 said:
just get my eeepad, I know the case/sleeve is required, do I really need a screen protector?
tks
Click to expand...
Click to collapse
Yes. A good screen guard not only protects your glass from getting scratched but also reduces glare and even provide better tactile touch. I love how my BSE skins feel. Very smooth and soft and not slippery (not everybody likes it though). Oh, and you can use your hand or sleeves to wipe the screen without fear
BSE offers DIY sizes, 12x14" is about $15 + shipping (buy 3 and shipping is free I think). I've already emailed them to see if they will have Transformer kits soon.
Itaintrite said:
Yes. A good screen guard not only protects your glass from getting scratched but also reduces glare and even provide better tactile touch. I love how my BSE skins feel. Very smooth and soft and not slippery (not everybody likes it though). Oh, and you can use your hand or sleeves to wipe the screen without fear
BSE offers DIY sizes, 12x14" is about $15 + shipping (buy 3 and shipping is free I think). I've already emailed them to see if they will have Transformer kits soon.
Click to expand...
Click to collapse
How does your BSE handle the glare and fingerprints? How did you trim it?
~DC
DevCake said:
How does your BSE handle the glare and fingerprints? How did you trim it?
~DC
Click to expand...
Click to collapse
I just measured the dimensions of the screen and used a razor to cut the BSE piece. I haven't used it outside yet so not sure about glare, but fingerprints are a-ok, as in they don't show up at all
I got the skinomi silver carbon fiber full protector today
and simply loving the design.
I am not sure how the screen is yet since I am waiting for it to dry
but i'll play with it when it does and see how it is and let you know what I think.
I'll also try to get some pictures up.
just want to interject a quick fact here, you guys know that the TF uses Gorilla glass right? it doesn't need a screen protector (at least for protection anyway) ... anything that can scratch gorilla glass would not be prevented by any screen protector you can get.
Sent from my Transformer TF101 using Tapatalk
Gorilla Glass is only scratch resistant, not scratch proof. It can still scratch.
finalhit said:
just want to interject a quick fact here, you guys know that the TF uses Gorilla glass right? it doesn't need a screen protector (at least for protection anyway) ... anything that can scratch gorilla glass would not be prevented by any screen protector you can get.
Sent from my Transformer TF101 using Tapatalk
Click to expand...
Click to collapse
gorilla glass does scratch. my dell streak has gorilla glass and i've got a small scrath on it. it's just harder to scratch than normal glass.
also screen protectors are good to stop fingerprints and some decrease the friction; so easier swiping across the screen which is good for playing games. btw zagg invisible shields increase friction.
Sent from my Transformer TF101 using XDA Premium App
Hey all...does the transformer dock to the keyboard correctly with the skins / screen protectors?
When I put the skinomi skin on my Galaxy Tab I experienced problems docking it to the HDMI stand/dock...
Anyone with input please advise...
Just a heads up for those planning on using the dock keyboard...
Thanks
recondo1202 said:
Hey all...does the transformer dock to the keyboard correctly with the skins / screen protectors?
When I put the skinomi skin on my Galaxy Tab I experienced problems docking it to the HDMI stand/dock...
Anyone with input please advise...
Just a heads up for those planning on using the dock keyboard...
Thanks
Click to expand...
Click to collapse
NO problems with the dock. It's tighter but still slips in.
I don't understand people's argument that Gorilla glass does not require a screen protector... there are numerous reasons to get a screen protector despite scratches. It feels differently, it reduces glare and fingerprints etc. I am happy I got one!
Found one on xoskins.com ......anybody have any experience with their products ?
I've been waiting forever because I love SteinHeil (sgpstore) screen protectors so much and I want something like that, instead of the wet application screen protectors. Help me find one pleease!
I have Skinomi & you can barely tell its on there. Plus, since it is a wet apply, I wasn't punished when I messed up the first time.
I have a clear B&E for sale if anyone is interested. Brand new, never used. PM me.
I just found a screen protector from lexard (think I spelled that wrong). Does anybody have experience with this company or know if this protector is any good?
Sent from my Transformer TF101 using XDA Premium App
I'm really starting to hate the texture of the Skinomi screen protector. It's slightly tacky and makes tracing kind of annoying. It's also not very durable on it's own and while acting as a buffer, it's prone to it's own nicks far more than thinker matte protectors I've used.
sent from a device using an app

ZAGG invisibleSHIELD Asus EEE Pad Transformer Prime Screen Protector?

My transformer prime hasn't arrived yet, but it should any day now. I'd like to have a screen protector ready to apply when I unbox the tablet.
Has anyone here used this ZAGG invisibleSHIELD with their Transformer Prime? Does it actually fit right on the front and back? Are there any issues with clarity? Does it still allow your finger to slide smoothly across the screen like it's supposed to?
zagg.com/invisibleshield/asus-eee-pad-transformer-prime-cases-screen-protectors-covers-skins-shields.php (bad link due to low post count)
Please post your own review, or link any other reviews you find in this thread.
----
Update: I went ahead and ordered it, since it has a lot of good reviews with other devices. If you order the full body version from zagg.com you automatically get free shipping. Using the coupon code "fbfans25" will also remove $10 from the price.
Looks the same as Extreme Guard for twice the price.
I got the Extreme Guard one and even though the back skin looks and works great, I wasn't too thrilled with the screen protector due to it being slightly (very) off and I couldn't get it lined perfectly and ended up throwing it away.
I ordered the full protector and it's on it's way. I have really liked the Zagg products in the past on other devices. I will post an update when I get mine and have it installed.
footar said:
I ordered the full protector and it's on it's way. I have really liked the Zagg products in the past on other devices. I will post an update when I get mine and have it installed.
Click to expand...
Click to collapse
Let us know if it fits in the dock if you have one. I know the skinomi skins have trouble with it when fully covered. Thanks
Yes let us know what you think of it once you get it. I have one on my iPhone and I'm considering it for my Prime but I have the same concerns you do regarding look and feel. I'm also curious about the fit at the back. Does it stretch over the raised ASUS lettering or is it cut out?
spiraleyes00 said:
My transformer prime hasn't arrived yet, but it should any day now. I'd like to have a screen protector ready to apply when I unbox the tablet.
Has anyone here used this ZAGG invisibleSHIELD with their Transformer Prime? Does it actually fit right on the front and back? Are there any issues with clarity? Does it still allow your finger to slide smoothly across the screen like it's supposed to?
zagg.com/invisibleshield/asus-eee-pad-transformer-prime-cases-screen-protectors-covers-skins-shields.php (bad link due to low post count)
Please post your own review, or link any other reviews you find in this thread.
Click to expand...
Click to collapse
where did you find one for the prime I have only seen it for og transformer?
My Zagg arrived today. It works great. Just make sure the bottom of the screen is securely on if you have the dock. It is a tight fit, but it certainly works wells.
I have it for just the screen btw....
Sent from my Transformer Prime TF201 using xda premium
Getting my Prime covered with GhostArmor tomorrow. They have kiosks at nearly every mall. If they do a bad job then you can request a refund. Costs 35 for full shield, and only 10 for following visits to entirely replace the skin.
I don't trust myself with clear shields.
i use the ZAGG TF101 only cause its cheaper...$14.99 and its only a bit smaller then the TFP201,with the case on, the screen is completely protected anyway so the TF101 ZAGG is probably the way to go!!! I love ZAGG products
colbyb25 said:
My Zagg arrived today. It works great. Just make sure the bottom of the screen is securely on if you have the dock. It is a tight fit, but it certainly works wells.
I have it for just the screen btw....
Click to expand...
Click to collapse
Have you noticed any line forming on the screen protector where it touches the dock? Someone was saying that happened with the full body skinomi protector in another thread.
BUYMECAR said:
Getting my Prime covered with GhostArmor tomorrow. They have kiosks at nearly every mall. If they do a bad job then you can request a refund. Costs 35 for full shield, and only 10 for following visits to entirely replace the skin.
I don't trust myself with clear shields.
Click to expand...
Click to collapse
Have u gotten the protector yet? I was thinking about doing this too. Is it too thick to fit in the dock?
I updated the original post with a coupon code(fbfans25) I found for 25% off. Hopefully when both the protector and the tablet come in I can post a short review.
i hate zaggs because they tend to stick to my fingers, i prefer bodyguardz. i get better grip with the zagg, but when playing games like fruit ninja, it gets really hard when my fingers are sticking the the protector. i have had about 4 zaggs, and 2 bodyguards. bodygurads are still my favorite
It didn't fit the screen correctly due to size differential? I'm considering getting the extreme guard caz of its price - do you know if it works with the dock?
ajamils said:
Looks the same as Extreme Guard for twice the price.
I got the Extreme Guard one and even though the back skin looks and works great, I wasn't too thrilled with the screen protector due to it being slightly (very) off and I couldn't get it lined perfectly and ended up throwing it away.
Click to expand...
Click to collapse
Ordered back and front. Got free shipping and $10 off so i paid $29.99 for back and front protection. Will update with pics and a review.
Sent from my Transformer Prime TF201 using xda premium
Ghost Armor just applied
I just put GA on my prime tonight so its still drying, etc.
Initial thoughts;
Unlike Zagg, there is less of the "orange Peel" effect, I didn't mind that in fact i have Zagg on all my phones and like the grippiness. The GA has a very slight orange peel but i think that is just the nature of a vinyl or poly protector.
It's very shiny, make the back look like it was shellacked, again not bad but the texture on Aluminum is lost.
I will say i was a disappointed with the cut of the front and back pieces, I don't know if the material shrinks after cutting but the front piece is a good 1/8 to short on one side. The back is about 1/16 all around. It doesn't look bad but i know its there.
There are cutouts for everything, the speaker, headphone jack, light sensors and cameras. the kit did come with thin pieces for the beveled edge. that was nice, those pieces are sized almost perfectly.
Question
For those you got the Zagg full body kit, how does it fit with the dock?
well i have them installed right now and they are leaving marks on the screens where the dock connects. not really impressed. i will probably remove the shields.
Sent from my Transformer Prime TF201 using xda premium
gsk3rd said:
well i have them installed right now and they are leaving marks on the screens where the dock connects. not really impressed. i will probably remove the shields.
Click to expand...
Click to collapse
That sucks! I have my full body shield waiting for the prime, which comes on Monday. Hopefully I can figure out some way to use it, even if it's the screen part only. I'd hate to have to send it back. Of course this all depends on whether or not I need to send the actual prime back due to dead pixels or some other issue.
Well i took the the screen one off but left the back on. You could cut the protector or notch out where the dock touches the screen.
Sent from my Transformer Prime TF201 using xda premium

Acase Screen Protector

Hi just wanted to get info from the people who have this specific screen protector on their prime, please. How is the touch responsiveness with the protector on & was it a perfect fit & does it reduce any kind of glare since it's not a matte finish? Thank you!!
http://www.amazon.com/Transformer-T...-Acase/dp/B006QFZ2QA/ref=cm_cr_pr_product_top
I got it, it does the job for me. If u want less glare and less fingerprints get the matted one
Sent from my Transformer Prime TF201 using Tapatalk
I put on a zagg. Went on pretty easy and touch response is great cant complain.
Sent from my Transformer Prime TF201 using Tapatalk
I just placed an order for the 3 pack, since it seems Steinheil won't be making a screen protector for the Prime. Or at least that was the response someone got when they asked. They haven't even returned my email from a couple weeks ago about it. I was hoping with enough people asking maybe they'd make one, but whatever..
I have the ZAGG on there now and HATE the feel of it. I'm glad I had a gift card so it only cost me $5 otherwise I'd be pretty unhappy for the price they're asking.
Sent from my cellular telephone using magic
sd_flip said:
Hi just wanted to get info from the people who have this specific screen protector on their prime, please. How is the touch responsiveness with the protector on & was it a perfect fit & does it reduce any kind of glare since it's not a matte finish? Thank you!!
http://www.amazon.com/Transformer-T...-Acase/dp/B006QFZ2QA/ref=cm_cr_pr_product_top
Click to expand...
Click to collapse
I bought the matte and clear versions of this screen protector. Decided to try the matte one first and I like it. It does dull the screen a little which I expected but it sure kills the glare and doesnt collect finger prints like the screen does with nothing on it, it also fit perfect on mine.
For now im going to leave the matte one on but I may try the clear in the future.
The clear non-matte ones have a really bad glare problem but colors shine. I wish I got the matte ones. It's personal choice. High quality film protectors.
Sent from my Xoom using xda premium

Best Skins Ever for Prime!

Just got an email this morning. BSE finaly made some skins for the prime. I already got the skinomi, but I will probably order a set of these. Great skin, had a couple sets for my iPad 1 and 2. And it still looks great after a year of use. email below with link
Hello,
Thank you for your interest in Best Skins Ever. We are proud to announce that we are now accepting orders for the Asus Eee Pad Transformer Prime TF201 Skins with shipments beginning immediately! This is no wussy screen protector. It is the ultimate in undetectable scratch defense covering your new device without changing its size, or more importantly, its look.
The Asus Eee Pad Transformer Prime TF201 Skins will be available for a special low introductory price for a short time.
You can find the new Asus Eee Pad Transformer Prime TF201 Skins at the following link: http://www.bestskinsever.com/asus-eee-pad-transformer-prime-tf201-skin
Be sure to pass this on to your friends on your favorite message boards and blogs. Thank you for your interest and continued support. We look forward to protecting your stuff well into the future.
Best regards,
Tracy M
Support Team
www.bestskinsever.com
Find us on Facebook and Twitter
www.facebook.com/bestskinsever
www.twitter.com/bestskinsever
Click to expand...
Click to collapse
Does anyone have any experience with these skins?
How do they feel and how durable are they?
I like that the back is all one piece (unlike the Skinomi) and that it fully surrounds the speaker which seems like an area where my Skinomi will eventually peel up (sharp corners = no no) but I don't want a screen protector that I can detect. If their screen protectors are similar to the SGP Ultra Crystal series though I might be convinced to pick one up.
From past experience, I believe its an invisible shield kind of feel to their screen protector too.
Anyone have more recent experience please correct me if I am wrong
I would buy one to replace my skinomi in a heartbeat as I had a lot of troubles with skinomi's separate side/edge pieces. But alas, it does not have a cut out for the dock, and this is a necessity for me.
Were they to make one with a cutout though...
Sent from my Transformer Prime TF201 using Tapatalk
BSE is the BEST SKINS EVER. Don't hesitate to buy from them, ever! Half the price of Zagg and twice the quality.
irishtexmex said:
I would buy one to replace my skinomi in a heartbeat as I had a lot of troubles with skinomi's separate side/edge pieces. But alas, it does not have a cut out for the dock, and this is a necessity for me.
Were they to make one with a cutout though...
Sent from my Transformer Prime TF201 using Tapatalk
Click to expand...
Click to collapse
Do you really need a cutout for the Dock? I have a clear Skinomi skin on the back of my TF Prime and I use it with the keyboard dock all the time with no problems? The only slight issue is that the foam pad inside the dock leaves an imprint on the skin, however it fades a few minutes after taking the tablet out of the dock.
I would recommend Best Skins Ever also. I kept checking their site for Prime versions...but up until a few days ago, there was no application available.
Got the Xtreme skin protector from eBay which is not great. Once applied, the Xtreme version is somewhat sticky (even though I tried invisishield spray...might try some wax next...front screen protector has dark cuts from being squeegeed out from applying - ordered dry application screen protectors).
Would definitely go with Best Skins. No problems so far on my HTC Sensation (since 9/2011) and wifey's ipad 2 (back only since it came out last year).
almightywhacko said:
Do you really need a cutout for the Dock? I have a clear Skinomi skin on the back of my TF Prime and I use it with the keyboard dock all the time with no problems? The only slight issue is that the foam pad inside the dock leaves an imprint on the skin, however it fades a few minutes after taking the tablet out of the dock.
Click to expand...
Click to collapse
Yes, because I use a matte screen protector on the front and it is distinguishably thicker than a regular, glossy screen protector. :-\ Otherwise it'd be no problem.
Sent from my Transformer Prime TF201 using Tapatalk
used it in the past, its the same quality as InvisibleShield. just a lot cheaper. i wonder if they are going to make a skin for the keyboard dock also
How hard is it to apply? I've driven myself crazy trying to apply some screen protectors. The main problem is soon as I get done clearing out all the dust/particles then seconds later more dust/particles plop right back on to the screen. I REFUSE to lay down the screen protector on any dust and I just can't find how to do this without ANY dust anywhere. It's just all over. Seems like I need operating room environment.
opentoe said:
How hard is it to apply? I've driven myself crazy trying to apply some screen protectors. The main problem is soon as I get done clearing out all the dust/particles then seconds later more dust/particles plop right back on to the screen. I REFUSE to lay down the screen protector on any dust and I just can't find how to do this without ANY dust anywhere. It's just all over. Seems like I need operating room environment.
Click to expand...
Click to collapse
do it in the bathroom, but steam up the room with running hot water from your sink and tub for maybe a good 20-30 minutes, then start applying it.
kwazytazz said:
do it in the bathroom, but steam up the room with running hot water from your sink and tub for maybe a good 20-30 minutes, then start applying it.
Click to expand...
Click to collapse
Wow, i never thought of this. That would take care of the dust and probably make it easier to install anyway. Nice......I'll give it a try!
opentoe said:
Wow, i never thought of this. That would take care of the dust and probably make it easier to install anyway. Nice......I'll give it a try!
Click to expand...
Click to collapse
NP! good luck and post back with results!
Quick question, if I just get the "body skin", that means I'm getting the back protector right? I'm only interested in back protection, as I prefer the traditional stiff glossy protectors for my screens.
I already have the Xtreme protector, but it doesn't protect the back bezel, which is a no no for me.
Thanks in advance
brennanyama said:
Quick question, if I just get the "body skin", that means I'm getting the back protector right? I'm only interested in back protection, as I prefer the traditional stiff glossy protectors for my screens.
I already have the Xtreme protector, but it doesn't protect the back bezel, which is a no no for me.
Thanks in advance
Click to expand...
Click to collapse
yeah, the body skin is just the back of the tablet. but pay 2 bux more and u can get both ;p. also they have a 20% off now
Anyone try out the body skin with the keyboard dock yet? Already have some small scratches on the back of my tablet.
I'm running with a skinomi full skin until after I RMA. (no issues with the dock^)
I ordered the full body version from BSE though. I must say there are a few things I like better about the cutouts.
On the screen, the skinomi has a cutout for the camera, and the light sensor. The BSE only has a cutout for the camera. In my opinion this is better as the other one isnt necessary.
Also, instead of two holes for the camera and flash on the back its one figure 8 shaped hole.
The skinomi also has a cutout for the Asus logo. The BSE is one solid piece. No cutout for the logo.
And finally, the skinomi has little side pieces. The BSE the back and sides are all one piece. The back curls around to the sides.
Thats all I've got... I think this one is a better design over the zagg and skinomi skins.
UPDATE
Best skins ever just released dock compatible versions of everything and a total body skin which includes a skin for the dock. They have it on special since its just released.
Ordered the total body kit for $23.16 + shipping
Just bought the full skin for my Prime and Maxx.

Best screen protector?

Hi, this is my first post here.
Im looking to buy a screen protector to protect my screen
Im currently looking at these two:
a) ZAGG invisibleSHIELD - Asus EEE Transformer Prime - SCREEN Protector
b) 2Pack S-Shieldz Asus EEE Pad Transformer Prime TF201 LCD Screen Protector Shield
I use the dock a lot which means that it should not get ripped out by the dock.
What im looking for is solid protection from my scratches my nails inflict on the screen.
It should also be nice to touch, i prefer something over which my hand glides even if the whole screen is filled with sweat from my hands.
Also i would prefer something which is easy to apply. I did a shoddy job with the screen protector on my iPhone 4 and now its full with air bubbles.
And last but not the least, Image quality should not take a hit.
Thanks.
I would post a link but it turns out i cant do that unless i post 10 messages
I don't have experience with either of them on the Prime, but I do have a Zagg screen protector on my phone, and it does the job well enough, but there is a bit of orange peel texture that comes through in certain lights. It feels nice to the touch, also.
Personally, when I finally break down and get a screen protector, I'm probably going to go with Skinomi. I had one on my last tablet, and I liked it better than the Zagg.
I use BodyGuardz for my Phone and Tablet http://www.bodyguardz.com/
I bought this, Ultra-thin Transparency & Super Clear protection screen protector
Two options.
First is go cheap, get the clear hard plastic ones from ebay. should be maybe a couple dollars? Like the cheap phone ones, they put on easy, but scratch easy. throw the used one away and buy another one.
Second option, get a high quality "military grade" protector. They are all very similar, essentially thicker, more of a rubbery feel to them, last a lot longer.
If you go for option two know that most of the brands are selling the same material in different packaging. Some are thinner than others (zag is one of the thickest) and thin usually means less rubbery / less texture to annoy you. After years of using a Zagg on my phone it recently got too dirty to use and im back to the plastic protectors, damn i forgot how clear my screen used to be! Will likely not go back to zagg. Good product for protection, bad for clarity.
There are kiosks in the malls around there that will do a custom protector for your device for around $50, much thinner material than zagg or others, and roughly the same price for front and back protection, only problem is lifetime guarentee is useless if the kiosks dissapear.
When all else fails, check out what friends are using, if you like a protector on their device, go for it. Often the online less expensive options can be just as good as zagg with half the cost, zagg is a ripoff because of huge markups.
SKINOMI.COM FOR THE WORLD! By far best of the military grade options in my opinion, and the greatest customer service I've ever experienced for easy replacements.
Sent from my SPH-D710 using Tapatalk 2
collinsac24 said:
SKINOMI.COM FOR THE WORLD! By far best of the military grade options in my opinion, and the greatest customer service I've ever experienced for easy replacements.
Sent from my SPH-D710 using Tapatalk 2
Click to expand...
Click to collapse
I have an Xrtreme Guard on my Prime right now. Got it for less than $5 on the website. It's similar to an Invisible Shield or Ghost Armor but has less of an orange peel feel and look.
ByzLat said:
Hi, this is my first post here.
Im looking to buy a screen protector to protect my screen
Im currently looking at these two:
a) ZAGG invisibleSHIELD - Asus EEE Transformer Prime - SCREEN Protector
b) 2Pack S-Shieldz Asus EEE Pad Transformer Prime TF201 LCD Screen Protector Shield
I use the dock a lot which means that it should not get ripped out by the dock.
What im looking for is solid protection from my scratches my nails inflict on the screen.
It should also be nice to touch, i prefer something over which my hand glides even if the whole screen is filled with sweat from my hands.
Also i would prefer something which is easy to apply. I did a shoddy job with the screen protector on my iPhone 4 and now its full with air bubbles.
And last but not the least, Image quality should not take a hit.
Thanks.
I would post a link but it turns out i cant do that unless i post 10 messages
Click to expand...
Click to collapse
I love the Skinomi. It's cut perfectly for my dock and it's fairly smooth.

Categories

Resources