Related
As question =) i would like to flash my phone back to stock until ics arrive but i dont know how to do it. Can someone give me a full tutorial?
I m using asia gsm razr xt910, thx
Maybe use this file and flash like you would any Rom?
Well if you find out your ROM region, then you can go download the appropriate ROM in the official ROM thread in the development section and use RSD lite to flash it back to factory ROM. That should work and your phone will be good as new.
http://forum.xda-developers.com/showthread.php?t=1416058
http://forum.xda-developers.com/showthread.php?t=1362956
What is rsd lite and how do i use it? I m noob in this ..
N how do i check my rom region? I m in the arctic now, n when i check my system info, i shows thst my system version is 651.167.20.xt910.retail.en.EU
So what should i do?million thanks to anyone who help me
Ive never done it myself but Im assuming region is the country your living in as some are gsm and some cdma.
On using rsd lite there are several how to with search.
http://www.blogotechblog.com/2011/12/restore-motorola-droid-razr-to-stock-configuration/
Got this from here.
INSTRUCTIONS:
1. If you haven't already done so in the past, download and install the motorola usb drivers.
2. Download and install RSD Lite 5.6.
NOTE: In order for RSD Lite to recognize your phone, it has to be in AP Fastboot mode or it can just be booted up like normal. If your phone will not boot up, then power it off and put it into AP Fastboot mode by holding the volume up + down + power. Then select the AP Fastboot option.
3. Connect your phone to the computer with a usb cable and open RSD Lite. Make sure RSD Lite recognizes your phone before proceeding.
WARNING: Be careful not to move your phone around or mess with the usb cable while doing the following steps. You don't want to accidentally disconnect it. That might end up bad.
4. In RSD Lite, select the fastboot zip file you downloaded then press the "Uncompress and Start Flashing" button. RSD Lite will unzip the file and begin flashing.
5. Once the flashing is done and your phone is booted up, perform a factory reset to complete the process
http://www.razrforums.com/forum/droid-razr-development/775-rsd-lite-fastboot-not-working.html
http://forum.xda-developers.com/showthread.php?t=1486718&highlight=droid+razr+utility
Thanks! Will try that once i free
Do i need to factory reset b4 do this?
omnia1994 said:
Thanks! Will try that once i free
Do i need to factory reset b4 do this?
Click to expand...
Click to collapse
Dont think so because as with my other phones when I restored it automatically wiped the phone.
Ok. Will report once i tried! Many thx for everyone!
Back to stock successfully . Thx!
I followed the steps shown by blueis300
After connecting the device in APFastoot mode I started RSD lite it recognized my device.
Then I selected the zip file and selected the Uncompress and flash option
After Uncompressing the flashing process starts and when it reaches 6/18 it fails.
Please Help!!
any infomation about y it failed?
As soon as it enters step 6 it fails. I have no idea why its failing.
Please Help otherwise i'll be stuck with this stupid ROM
I live in India so is there any problem with the region or something??
r u sure u downloaded the correct rom?
I Got it!!!
This is kind of different from random reboots, because no matter what I am doing on the device or if its ideal, it does reboot around every 3 minutes.
Current version is 4.0.4 and the model of the device is Verizon xt912
System version: 6.16.211.xt912.Verizon.en.US
Kernel version: wt-3.0.0
Build no.: 6.7.2-180 ....
Build date: Jun 14, .... 2012
Another thing is, under the settings, the device is showing Baseband and IMEI - Unknown. Don't know what may have caused this. BTW, currently I am out of country (US) and I have no SIM inserted in the slot (for international GSM), I don't suppose inserting no SIM can lead to base band and IMEI = unknown?
I am no idea if this Unknow Baseband and IMEI is causing the reboot or vice-versa or if there's dependence.
What I have tried:
Wiping Cache through recovery
Reset to factory settings
Option 1 of Matt's Razr Utility 1.82
If anyone can tell me how can I make this phone usable, I would be thankful.
Did you try flashing official FXZ using RSD lite ?!
Sent from my DROID RAZR using Tapatalk 2
ryan8r said:
Did you try flashing official FXZ using RSD lite ?!
Sent from my DROID RAZR using Tapatalk 2
Click to expand...
Click to collapse
Not really, but would it be any different than restoring to ICS .211 using Matt's Razr Utility?
Can you tell me where I can find the official FXZ for Razr to flash?
It will be different cause stock fxz includes every part of the firmware while matts utility can only install certain parts of it like the system, boot etc.
The RSD simply doesn't detect the device. USB drivers are installed and gets detected fine with Matt's Razr Utility.
Tried different RSD versions. I also tried replacing all the radio, system, boot img and all other files in the Matt's Razr Utility with the FXZ which I was trying to restore back to. It said it did successfully flashed to 211 but the problem is still there.
I think if there's any way to change the base band from Unknown to the original, this problem can be corrected. Any ideas for this?
I cant say why RSD wont detect your device but "Baseband unknown" could be a Bad ESN or a blocked device and a corrupt PDS partition in the worst case..
That said if you do have any of the above your CDMA.XX.XXX baseband is most probably useless what you could try is to get your device to switch to a GSM baseband N.01.XXX and make use of the device with any operational GSM service in your country.
In order to do that root your device install Safestrap and flash any of the GSM roms available.
Try that and tell me the results.
Sent from my DROID RAZR using Tapatalk 2
^
I'll try that and let you know.
While trying to get it to work, I cannot find the EFS folder. I am using Android Commander on PC to browse the files and folders of the device. Its right at the very root, i.e at the location " / " right? Where there are folders like Sys, System, Root, preinstall, preoc etc
You've installed motorola usb drivers,
When the phone is powered off, hold both VOLUME UP + DOWN buttons and press POWER button. You'll get into bootmenu. Release the buttons and navigate with VOLUME DOWN to AP FASTBOOT mode, press VOLUME UP to get into AP FASTBOOT MODE. Connect the phone to pc, launch RSD Lite ( newest version 6.1.4 )
If it detects the phone, flash stock xt912 ics rom.
Semseddin said:
You've installed motorola usb drivers,
When the phone is powered off, hold both VOLUME UP + DOWN buttons and press POWER button. You'll get into bootmenu. Release the buttons and navigate with VOLUME DOWN to AP FASTBOOT mode, press VOLUME UP to get into AP FASTBOOT MODE. Connect the phone to pc, launch RSD Lite ( newest version 6.1.4 )
If it detects the phone, flash stock xt912 ics rom.
Click to expand...
Click to collapse
I don't know why but the RSD lite does not detect the phone. USB drivers are installed and working fine because matt's razr utility detects the phone (before it wasn't).
You may need to run RSD Lite as Administrator for it to work on Win 7/8.
You need to get it to successfully complete flashing the radios in recovery after it finishes the other partitions.
It should reboot into recovery by itself and flash the BP.img and LTE.img and then reboot again normally after it has completed.
That should fix the Baseband unknown and blank IMEI issue.
cellzealot said:
You may need to run RSD Lite as Administrator for it to work on Win 7/8.
You need to get it to successfully complete flashing the radios in recovery after it finishes the other partitions.
It should reboot into recovery by itself and flash the BP.img and LTE.img and then reboot again normally after it has completed.
That should fix the Baseband unknown and blank IMEI issue.
Click to expand...
Click to collapse
I am on Win 7 64 bit.
Running as Admin, but still RSD Lite does not show the device. Is there anything else that I can try?
I'll also try running on a different PC.
http://db.tt/EMFh9jos
That is RSD Lite 6.1.4 the latest available version. Try it and see if you have any better results.
Can you use ADB ?!
And Did you try any of the GSM roms ?!
Accidentally Sent from my iPhone using Tapatalk
cellzealot said:
http://db.tt/EMFh9jos
That is RSD Lite 6.1.4 the latest available version. Try it and see if you have any better results.
Click to expand...
Click to collapse
I am using 6.1.4 and have also tried 5.9. Anything else that I can try?
ryan8r said:
Can you use ADB ?!
And Did you try any of the GSM roms ?!
Accidentally Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
No. I think I'll try that.
I am uploading a zip file that is just the radio_update_211_RAZR.zip in the radio.img from the 211 FXZ.
You will need to put the file on the root of your sdcard. Since the phone isn't booting, the easiest way is to take out the sdcard and put it in a card reader on your PC to transfer the file. Then reinsert the sdcard in your phone and reboot the phone holding Vol up and down + PWR to get to the boot menu and select recovery.
The phone will boot to M logo and then blank screen briefly and then show the stock recovery with Android and red Exclamation !. Press both Vol up and down at the same time to enter recovery and chose Apply Update from External Storage option and browse to the update_radio_211_RAZR.zip and select it.
It should load lte.img and bp.img and then reboot automatically.
This should allow the phone to boot normally and display the baseband and IMEI again if everything works as described.
https://dl.dropbox.com/u/7632904/update_radio_211_RAZR.zip
This will avoid the need for RSD Lite if it works. If not, then you can try using fastboot to manually flash the images from the FXZ.
press all three bttn,on black and white menu scroll down and select "BP HW Diag & Boot AP" boot will boot up ,see if phone restarts on its on or not and lemme know ...
cellzealot said:
I am uploading a zip file that is just the radio_update_211_RAZR.zip in the radio.img from the 211 FXZ.
You will need to put the file on the root of your sdcard. Since the phone isn't booting, the easiest way is to take out the sdcard and put it in a card reader on your PC to transfer the file. Then reinsert the sdcard in your phone and reboot the phone holding Vol up and down + PWR to get to the boot menu and select recovery.
The phone will boot to M logo and then blank screen briefly and then show the stock recovery with Android and red Exclamation !. Press both Vol up and down at the same time to enter recovery and chose Apply Update from External Storage option and browse to the update_radio_211_RAZR.zip and select it.
It should load lte.img and bp.img and then reboot automatically.
This should allow the phone to boot normally and display the baseband and IMEI again if everything works as described.
https://dl.dropbox.com/u/7632904/update_radio_211_RAZR.zip
This will avoid the need for RSD Lite if it works. If not, then you can try using fastboot to manually flash the images from the FXZ.
Click to expand...
Click to collapse
ii m having exact same problem as listed by op , i tired flashing this zip file following error came up on screen
assert failed: motorola.motoflash(" /tmp/bp.img")
E:error in /tmp/sideload/package.zip
(status 7)
Installation aborted.
cellzealot said:
I am uploading a zip file that is just the radio_update_211_RAZR.zip in the radio.img from the 211 FXZ.
You will need to put the file on the root of your sdcard. Since the phone isn't booting, the easiest way is to take out the sdcard and put it in a card reader on your PC to transfer the file. Then reinsert the sdcard in your phone and reboot the phone holding Vol up and down + PWR to get to the boot menu and select recovery.
The phone will boot to M logo and then blank screen briefly and then show the stock recovery with Android and red Exclamation !. Press both Vol up and down at the same time to enter recovery and chose Apply Update from External Storage option and browse to the update_radio_211_RAZR.zip and select it.
It should load lte.img and bp.img and then reboot automatically.
This should allow the phone to boot normally and display the baseband and IMEI again if everything works as described.
https://dl.dropbox.com/u/7632904/update_radio_211_RAZR.zip
This will avoid the need for RSD Lite if it works. If not, then you can try using fastboot to manually flash the images from the FXZ.
Click to expand...
Click to collapse
It says, Finding, Opening, Verifying, Installing update....
assert failed: motorola.motoflash("/tmp/bp.img")
E:Error in /tmp/sideload/package.zip
(Status 7)
Installation aborted.
BTW, I tried this when being on 215.
Should I go to 211 and then try again?
karansawhney said:
press all three bttn,on black and white menu scroll down and select "BP HW Diag & Boot AP" boot will boot up ,see if phone restarts on its on or not and lemme know ...
Click to expand...
Click to collapse
In BP HW Diag & Boot AP, it does not reboot on its own.
lamborg said:
It says, Finding, Opening, Verifying, Installing update....
assert failed: motorola.motoflash("/tmp/bp.img")
E:Error in /tmp/sideload/package.zip
(Status 7)
Installation aborted.
BTW, I tried this when being on 215.
Should I go to 211 and then try again?
In BP HW Diag & Boot AP, it does not reboot on its own.
Click to expand...
Click to collapse
so both of us are in a same boat my phone acts the same and if i use matts utility i file gets created everytime in my phones internal storage named "update_radio.zip.failure"
If you're using BMM or SAFESTRAP 3.10 with stock ROM flashing enabled I can make you a flashable patch that will allow GSM services to work on the stock ROM itself !?
I'm only trying to help cause I've owned 2 RAZR's previously with the same condition. As I stated earlier if a radio flash or FXZ doesn't fix it then it is a corrupt PDS partition and it cannot be fixed to work on the CDMA baseband.
Sent from my DROID RAZR using Tapatalk 2
I am having a problem. I was trying to upgrade to Jelly bean 4.1 on this Atrix 4g. I tried to go through the steps that it gave online with the CM10 n Cyro and all. Long story short it couldn't find the rom within the zip or something of that nature. In other words, it screwed me over. I can't get back into recovery. It's been giving me this error:
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Before it was giving me just:
Failed to boot 4
Starting RSD mode
I had tried reseting to factory through the moto-fastboot but of course it failed. I have been tryin like crazy to flash various SBF from 2.3.5 to 2.3.6. I was originally at 2.3.6 but for what ever reason when I try the RSD lite it gives me the error after it executes "Phone did no re-enumerate after RAM downloader was sent". (0x703e). I have been reading forums literally all day. Perhaps I am not understanding something therefore I am missing it but maybe one of you guys could help me out with this? Maybe there is a real simple fix or maybe I completely ruined it? Either way it would be nice to get some help on this. Basically when I was trying to upgrade to 4.1 I followed "How to upgrade the Atrix 4G to Android 4.1.1 Jelly Bean via CyanogenMod 10" off of the androidauthority website. I got to step 9 but it couldn't find the ROM, by then it was too late.
UPDATE: So I got just that and RSD was flashing it until it reached yet another error:
failed flashing process. Failed flashing process. Phone[0000]: error switching phone BP pass through mode (0x70BE); phone disconnected.
Help?
majorrazer said:
Help?
Click to expand...
Click to collapse
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
saldirai said:
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
Click to expand...
Click to collapse
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
majorrazer said:
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
Click to expand...
Click to collapse
Do you have an unlocked bootloader? Does the word "Unlocked" appear when you power the phone on? You must have an unlocked bootloader for sure. IF not, you must unlock it.
his is the guide you were following;
http://www.androidauthority.com/atrix-4g-mb860-android-4-1-1-jelly-bean-cyanogenmod-10-cm10-106639/
As said there, it requires unlocked, rooted Atrix with with ClockworkMod Recovery installed
I guess you can still unlock the bootloader and install cwm recovery. Just search and find instructions.
HEY
i have the same problem also.... and the same error...
is your phone fix already?
could you tell me how?
SVF: 108:failed to boot 3 starting RSD mode
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
salimdawar said:
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
Click to expand...
Click to collapse
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
salimdawar said:
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
Click to expand...
Click to collapse
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Yes already install this file from Net
"Motorola_End_User_Driver_Installation_5.1.0_64bit "
and not expect any thing else about flashing of my device.
Before Motorola Atrix 4G, i were used in passed Samsung S1, S2, S3, & T989 (T-Mobile S2 version). All these andriod sets were very easily hack or Root and can install Roms easily .
But Moto Atrix 4G can me upset and sad.
kindly help me to re-connect my self to the andriod world by this Motorola Atrix 4G, thanks
Hey guys I'm having trouble getting to RSS mode my phone comes on then it says entering nv flash recovery mode then the phone dies so I need help trying to get into my phone to flash the sbf file
Sent from my GT-N7105 using XDA Premium 4 mobile app
Need Help regarding Motorola Atrix Mb 861.
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
kamal.navigator said:
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
Click to expand...
Click to collapse
Were you bootloader unlocked before getting this message?
Hi,
I tried to root my phone using TWRP, ADB & Fastboot but my phone is stuck in boot. It restarts as soon as the Acer logo is displayed. I need stock ROM for my phone. Please help me in resetting the phone.
My phone details are below :
Model Number: T04
Android version: 5.1
Kernel version: 3.10.65
Image version: Acer_AV0L0_T04_RV01RC07_IND_GEN1
Build Number : Acer_AV0L0_T04_1 .007.00_IND_GEN1
Thanks.
Kumaranil_1918 said:
Hi,
I tried to root my phone using TWRP, ADB & Fastboot but my phone is stuck in boot. It restarts as soon as the Acer logo is displayed. I need stock ROM for my phone. Please help me in resetting the phone.
My phone details are below :
Model Number: T04
Android version: 5.1
Kernel version: 3.10.65
Image version: Acer_AV0L0_T04_RV01RC07_IND_GEN1
Build Number : Acer_AV0L0_T04_1 .007.00_IND_GEN1
Thanks.
Click to expand...
Click to collapse
Here you are:
https://drive.google.com/file/d/0B35guFajHaQfYUJrWnRON3FTbDg/view
Also here is some links that is veeery useful to you:
http://vache-android.com/?dir=hubicAcer/Z630S
MigoMujahid said:
Here you are:
https://drive.google.com/file/d/0B35guFajHaQfYUJrWnRON3FTbDg/view
Also here is some links that is veeery useful to you:
http://vache-android.com/?dir=hubicAcer/Z630S
Click to expand...
Click to collapse
Thank you but is it compatible with my phone? I tried rooting using 'TWRP_2860_Z630S-T04_Shreps.img' file. When I unlocked bootloader using the fastboot command, my phone was reset. Then, I flashed the above image using fastboot for custom recovery so that I can install SuperSu but phone stuck in boot as soon as I entered fastboot reboot. Since then, my phone is in bootloop. Manual reset using the phone button isn't working.
Kumaranil_1918 said:
Thank you but is it compatible with my phone? I tried rooting using 'TWRP_2860_Z630S-T04_Shreps.img' file. When I unlocked bootloader using the fastboot command, my phone was reset. Then, I flashed the above image using fastboot for custom recovery so that I can install SuperSu but phone stuck in boot as soon as I entered fastboot reboot. Since then, my phone is in bootloop. Manual reset using the phone button isn't working.
Click to expand...
Click to collapse
It's compatible with your phone, there is another image in the other link i gave you but an older firmware, you can try it too
There is also this lollipop rooted one :
https://drive.google.com/file/d/0BwF5fKdxM85SenRSSnU1c3JHczg/view?usp=sharing
And this one is thought to be marshmallow:
https://drive.google.com/file/d/0BwF5fKdxM85SQmVhQ0IzX3dwWEU/view?usp=sharing
MigoMujahid said:
It's compatible with your phone, there is another image in the other link i gave you but an older firmware, you can try it too
There is also this lollipop rooted one :
https://drive.google.com/file/d/0BwF5fKdxM85SenRSSnU1c3JHczg/view?usp=sharing
And this one is thought to be marshmallow:
https://drive.google.com/file/d/0BwF5fKdxM85SQmVhQ0IzX3dwWEU/view?usp=sharing
Click to expand...
Click to collapse
Thank you. WIll try and let you know. Can you please tell me how to flash the recovery since my phone is stuck in bootlloop?
Kumaranil_1918 said:
Thank you. WIll try and let you know. Can you please tell me how to flash the recovery since my phone is stuck in bootlloop?
Click to expand...
Click to collapse
Using adb you can flash the recovery but it requires the USB debugging yo be enabled on your phone, and your phone is bootloaped so we are almost in a dead end here, what do you get when you try to enter the recovery?
MigoMujahid said:
Using adb you can flash the recovery but it requires the USB debugging yo be enabled on your phone, and your phone is bootloaped so we are almost in a dead end here, what do you get when you try to enter the recovery?
Click to expand...
Click to collapse
I already enabled usb debugging mode and unlocked bootloader before flashing the TWRP image. I don't know how to enter into recovery mode. I tried every key combination but my phone restarts once Acer logo is displayed. A blank screen is displayed, then phone vibrates and acer logo is displayed. Again, the same thing happens.
Kumaranil_1918 said:
I already enabled usb debugging mode and unlocked bootloader before flashing the TWRP image. I don't know how to enter into recovery mode. I tried every key combination but my phone restarts once Acer logo is displayed. A blank screen is displayed, then phone vibrates and acer logo is displayed. Again, the same thing happens.
Click to expand...
Click to collapse
Have you tried power button with volume up or with volume down,?
If you succeed, do the following while in the bootloader menu
To flash TWRP with adb, you must have adb & fastboot installed, download the installation from here.
Now connect your device to your PC and go to the folder where your TWRP is and press and hold shift then right click on an empty place on the folder and choose "Open command window here"
Now type following commands at command prompt.
Code:
adb reboot bootloader
to boot your device into bootloader.
after booting into bootloader type
Code:
fastboot flash recovery xxxx.img
"xxxx" refers to the recovery file name.
After the process finishes, try booting into the Recovery using Power+Volume up.
MigoMujahid said:
Have you tried power button with volume up or with volume down,?
If you succeed, do the following while in the bootloader menu
To flash TWRP with adb, you must have adb & fastboot installed, download the installation from here.
Now connect your device to your PC and go to the folder where your TWRP is and press and hold shift then right click on an empty place on the folder and choose "Open command window here"
Now type following commands at command prompt.
Code:
adb reboot bootloader
to boot your device into bootloader.
after booting into bootloader type
Code:
fastboot flash recovery xxxx.img
"xxxx" refers to the recovery file name.
After the process finishes, try booting into the Recovery using Power+Volume up.
Click to expand...
Click to collapse
Thanks. I tried the combination but nothing happens. I also tried removing the battery and connecting the phone to pc. Once I connect without battery, a blue charging light appears on the top left hand side. Then, I tried the key combinations again. The phone vibrates but blank screen is being displayed. Is there any way I can recover using SP flash tool using the scatter file in the link provided above?
Kumaranil_1918 said:
Thanks. I tried the combination but nothing happens. I also tried removing the battery and connecting the phone to pc. Once I connect without battery, a blue charging light appears on the top left hand side. Then, I tried the key combinations again. The phone vibrates but blank screen is being displayed. Is there any way I can recover using SP flash tool using the scatter file in the link provided above?
Click to expand...
Click to collapse
I tried flashing the file "Acer_AV0L0_T04_1.001.00_EMEA_GEN2_(rooted)" using SP flash tool and I got the errors. I've attached screenshots of both the errors. Now my phone isn't booting when I press the power button. No vibrations, only blank screen. I searched in Google and "Error Message: S_DL_GET_DRAM_SETTING_FAIL (0x13BE), Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings". Please help.
Kumaranil_1918 said:
I tried flashing the file "Acer_AV0L0_T04_1.001.00_EMEA_GEN2_(rooted)" using SP flash tool and I got the errors. I've attached screenshots of both the errors. Now my phone isn't booting when I press the power button. No vibrations, only blank screen. I searched in Google and "Error Message: S_DL_GET_DRAM_SETTING_FAIL (0x13BE), Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings". Please help.
Click to expand...
Click to collapse
The firmware is compatible, try flashing with SP Flash tool v3 not v5.
MigoMujahid said:
The firmware is compatible, try flashing with SP Flash tool v3 not v5.
Click to expand...
Click to collapse
Which options do I choose now? I assume I have to select 'Format All + Download' option since my phone isn't booting when I press the power button. No vibrations, only blank screen. Also, I need to know if all the files provided in the ROM need to be checked in SP flash tool for flashing or just Recovery.img.
Kumaranil_1918 said:
Which options do I choose now? I assume I have to select 'Format All + Download' option since my phone isn't booting when I press the power button. No vibrations, only blank screen. Also, I need to know if all the files provided in the ROM need to be checked in SP flash tool for flashing or just Recovery.img.
Click to expand...
Click to collapse
Well, choosing the recovery only will flash the recovery only, keep it default and try "download"
MigoMujahid said:
Well, choosing the recovery only will flash the recovery only, keep it default and try "download"
Click to expand...
Click to collapse
Just to confirm, I just select 'Download only' option and keep the checked items as it is without changing and flash using SP Flash tool v3. Am I right?
Kumaranil_1918 said:
Just to confirm, I just select 'Download only' option and keep the checked items as it is without changing and flash using SP Flash tool v3. Am I right?
Click to expand...
Click to collapse
Yes that should absolutely work...
-----------------------------------------
If i Helped you, support me and press the "thanks" button
MigoMujahid said:
Yes that should absolutely work...
Click to expand...
Click to collapse
Thanks. I'll try now and let you know.
Kumaranil_1918 said:
Thanks. I'll try now and let you know.
Click to expand...
Click to collapse
I tried flashing using the below versions:
SP-Flash-Tool-v3.1224.0.100
SP-Flash-Tool-v3.1312.0.139
SP-Flash-Tool-v3.1316.0.150
SP-Flash-Tool-v3.1328.0.183
SP-Flash-Tool-v3.1332.0.187
SP-Flash-Tool-v3.1344.0.212
I got many error messages. I've attached them. I've also tried downloading and installing 'Mediatek_USB_Driver_Auto-Installer_5.1632.00'. The flashing still doesn't work.
Kumaranil_1918 said:
I tried flashing using the below versions:
SP-Flash-Tool-v3.1224.0.100
SP-Flash-Tool-v3.1312.0.139
SP-Flash-Tool-v3.1316.0.150
SP-Flash-Tool-v3.1328.0.183
SP-Flash-Tool-v3.1332.0.187
SP-Flash-Tool-v3.1344.0.212
I got many error messages. I've attached them. I've also tried downloading and installing 'Mediatek_USB_Driver_Auto-Installer_5.1632.00'. The flashing still doesn't work.
Click to expand...
Click to collapse
Can you please tell me how to proceed now?
Kumaranil_1918 said:
Can you please tell me how to proceed now?
Click to expand...
Click to collapse
Press download first, then plug the phone to usb
MigoMujahid said:
Press download first, then plug the phone to usb
Click to expand...
Click to collapse
Yes, I selected 'Download' option and then connected my phone with battery in it. I left the checked boxes as it is. You can see them in the screenshots. The tool didn't proceed from 0%. It showed the errors which I've attached previously.
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
EFAYSAL said:
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
Click to expand...
Click to collapse
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
SubwayChamp said:
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
Click to expand...
Click to collapse
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
EFAYSAL said:
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
Click to expand...
Click to collapse
Ok, I guess that your device is actually in bootloop and don´t booting.
Tutorial that you followed has many steps and don´t need to do all this to just root device and it contains some files like lk.bin that you can´t be sure that should be for your device.
Some users use this file (lk.bin) of an unlocked device and think that flashng in other device then get unlock it but no need, your device can be unlock it just follow some commands in fastboot mode.
Now you can do the next;
Try to flash again your rom stock (I guess that you don´t have a backup), if for some reason your official tool doesn´t work then use only some images like boot, system and userdata with the scatter.txt to flash them through SP Flash Tool.
Here a link to TWRP https://youtu.be/6vj_BY6xJdA, you can root it with supersu v2.78 0r v2.82 and here some files that can be usefull too https://drive.google.com/uc?id=0BwJgeCYTpnEHNlg2VUlieHFTYVU&export=download
Update steps that you are following to can assist. What extension has your rom and if it is recogniced for SP Flash Tool. I didn´t ask you if you can enter to fastboot mode and if you can then you can know if your bootloader is unlocked typing fastboot oem info
Most info that you give and some screenie will help to understand better
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
EFAYSAL said:
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
Click to expand...
Click to collapse
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
SubwayChamp said:
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
Click to expand...
Click to collapse
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
EFAYSAL said:
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
Click to expand...
Click to collapse
I´m not sure if you are connecting correctly your device at right time and form to can flash it properly. Every device has more or less a specific way to do it. My last alcatel it was connected just with device power off and after to tap on download, but in other device Blu Dash was connected pressing just vol_up and my last mt6757 Bluboo had to press both vol up and down at time to connect to pc and after to tap on download option. To have sure that is well done increase volume in your pc, you will hear a first sound that is cause pc is recognicing but then you have to hear a second sound that is when SPFlashTool is recognicing device and you will see a red line in down side of the tool window, release button inmediately and let tool to work.
This is a good rom for your device according the author is optimized https://droid1311.blogspot.com/2017/08/alcatel-fl02-aka-flash-plus-2-via.html and this is the link directly if you have troubles with pop-up-adds https://drive.google.com/file/d/0BwAGh1drb91SeDZwV1VXbXpjQWM/view
Also you can try with other versions of SP Flash Tool, most stable maybe should be v5,1628 https://androidmtk.com/smart-phone-flash-tool leth me know how you go
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
SPFlashTool 5.1628:
I try all the way with and without pressing any button but no luck . And when it work finishing with error.
SPFlashTool 5.1628:
I try all the way to get that mode but nothing works. So I try to click download button then conect the phone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
EFAYSAL said:
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
I try all the way to get that mode but nothing works. So I try to click download button then conect the pkone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
Click to expand...
Click to collapse
There is a part that is not variable in the way to use this tool, ever you have to tap on download before to connect device and is recommendable too connect cable usb to pc (not yet to device); from here is when the button that you have to press can vary but like I said you before in my last mt6757 (a very similar to yours) works pressing both vol at same time to connect terminal cable to device and now you will see a red line (could be violet-ish)
Try before just flashing only preloader file to recreate some partitions and then do other flash for the other files.
Of course you have to be sure that all drivers are installed correctly cause this tool needs to put your device in download mode (a special level) and also keep it in this state so find VCOM drivers for Alcatel and adb/fastboot installer and try to uninstalling some older drivers that you don´t use and many times we keep in our pcs and for a short data transmission can helo that all the rom move it in same folder where SPFlashTool is allocated.
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
EFAYSAL said:
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
Click to expand...
Click to collapse
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
- In what android version are you, 6.0?
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
- Did you try to flash just preloader, only this file?
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
SubwayChamp said:
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
Click to expand...
Click to collapse
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
SubwayChamp said:
- In what android version are you, 6.0?
Click to expand...
Click to collapse
Yes, last time it was 6.0 before the root
SubwayChamp said:
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
Click to expand...
Click to collapse
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
SubwayChamp said:
- Did you try to flash just preloader, only this file?
Click to expand...
Click to collapse
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
SubwayChamp said:
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
Click to expand...
Click to collapse
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
EFAYSAL said:
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
Yes, last time it was 6.0 before the root
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
Click to expand...
Click to collapse
You need to try two different ways to flash files and restore your device.
First method: fastboot mode
You need to get device enter to fastboot in order to flash some files like system, boot and userdata, then there are two main methods to do it:
- Pressing pwr + vol down
- And I mentioned that sometimes work pressing both volume button + pwr and a menu have to appear to can select an option to enter to (fastboot mode), in some devices this method is not working but you have to try several times attempting to.
Second method: SPFlashTool
You have to ever press first of all Download box and connect terminal cable to pc and the buttons thhat you need to press at time to connec cable usb to your device may vary, sometimes vol down, sometimes both vol but never pwr button; if pc recognice then you have to release all buttone an let it pc continue the flash process.
If SPFlashTool recognice device first flash only preloader file and select now lk.bin too. Flash only these two files and after do again a new flash with the rest of the files, Why you need to do this? your partitions are corrupted and you need to restore them with these files in order to can flash all another files.
Before all of this charge your battery, if you have a cover removable then extract it some minutes and put it again.
Also I read that for this model it´s used this tool instead of SPFlash Tool https://androidmtk.com/download-sugar-mtk-sp-flash-tool (inside the zip you will find a password to start the tool) but I´m not sure what kind of rom it needs, you have to connect your device to begin the process, you will find in product models section in the tool this variant for your device "FL02"
Try first the other tool and then this and let me know how you go, mtk devices are almost unbrickeable so it´s just to find the appropriate way to return it to the life.
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
EFAYSAL said:
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
Click to expand...
Click to collapse
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
I understand that you tried with Sugar tool with no lucky.
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Is there some custom development, recovery, roms for your device?
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
SubwayChamp said:
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
Click to expand...
Click to collapse
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
SubwayChamp said:
I understand that you tried with Sugar tool with no lucky.
Click to expand...
Click to collapse
Yes. After recognizing it keeps trying to download data but no luck.
SubwayChamp said:
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Click to expand...
Click to collapse
I know it is disappointing!. I try this but no luck.
SubwayChamp said:
Is there some custom development, recovery, roms for your device?
Click to expand...
Click to collapse
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
SubwayChamp said:
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
Click to expand...
Click to collapse
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
EFAYSAL said:
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
Yes. After recognizing it keeps trying to download data but no luck.
I know it is disappointing!. I try this but no luck.
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
Click to expand...
Click to collapse
I´ll tell you some ideas with no any specific order that you can try or see if works.
Really very strange that display stays in black, you told me that flashing files through fastboot is working but doesn´t appear not even bootlogo, connect to pc as it is and see how pc recognices in devices manager and my pc if appears like a determined drive d/e/f so it looks that some bad flashing burn your kernel and this case is similar to when a Samsung device need to use jtag method to revive, if in your country no-one knows about Alcatel devices this could be a similar case to what I´m saying then it could be a clue for a technician. I tell you this cause many time ago when I flashed by error a Samsung s4 and only this method revived my device.
Try this, flash your stock recovery only through SPFlash tool and flash after through Alcatel Download tool your stock rom cause some firmwares need to detect stock recovery first to can flash other partitions.
At this stage don´t you have stock recovery, no? so you can try to format data cause sometimes when bootloader is altered then avoid to boot and formatting data can solve this.
If this recovery twrp is for your device you can try flashing through SPFlash tool, you have to put recovery.img and scatter-txt in a same folder. then if succesfull format data, system, wipe cache and dalvik and maybe later try to port some custom rom would be a way to solve this.
To flash any partition through fastboot this is the syntax, just follow one by one any of the files that are in your rom folder so just follow these, if some of then can´t be flashed don´t worry then it´s not flashable:
fastboot flash boot bot.img
fastboot flash cache cache.img
fastboot flash lk lk.bin
and so on till the end
...But after try this if you didn´t get boot to recovery and obviously you can´t delete data nor system then delete first the next partitions trough fastboot typing:
fastboot erase system
fastboot erase cache
fastboot erase userdata
fastboot erase boot
Try all this and let us see how it goes
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
EFAYSAL said:
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
View attachment 4518365
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
Click to expand...
Click to collapse
I see that Sugar tool detects your device like rooted and refuses to flash anything, compare imei number which is in the box, I hope that it couldn´t be changed.
Don´t tell me simply no luck, what it says in SPFlash tool when you tried to flash TWRP and I guess that you put scatter-txt and twrp renamed recovery.img simply in the same folder. Just to be clear, to can flash with this tool your device it has to be off not needed fastboot for this. (provide some screenie)
Other combination of keys to enter to fastboot to flash some partitions when something is missing is, try these three ways:
- Pressing only vol down and at same time connecting to charger (connect first one terminal of cable to your device and then to the charger)
- Pressing the three buttons till a menu appears (you must to release inmediately all)
- Pressing vol up + pwr till a menu appears (you must to release pwr button inmediately) then choose fastboot
In the post 4 I provided a link from Google Drive, in this zip there are 8 items;
- From the item 2 use this version of SP Flash tool, put the four files in a folder and flash them
- In the item 3 you will find some scripts for fastboot, maybe they´re working better and also you have here a subfolder with twrp image.
- And if you get sucessfully install twrp in the item 7 there is a backup with some files to restore from this recovery.
Try one by one and update the info, I hope that your motherboard is not damaged.