As question =) i would like to flash my phone back to stock until ics arrive but i dont know how to do it. Can someone give me a full tutorial?
I m using asia gsm razr xt910, thx
Maybe use this file and flash like you would any Rom?
Well if you find out your ROM region, then you can go download the appropriate ROM in the official ROM thread in the development section and use RSD lite to flash it back to factory ROM. That should work and your phone will be good as new.
http://forum.xda-developers.com/showthread.php?t=1416058
http://forum.xda-developers.com/showthread.php?t=1362956
What is rsd lite and how do i use it? I m noob in this ..
N how do i check my rom region? I m in the arctic now, n when i check my system info, i shows thst my system version is 651.167.20.xt910.retail.en.EU
So what should i do?million thanks to anyone who help me
Ive never done it myself but Im assuming region is the country your living in as some are gsm and some cdma.
On using rsd lite there are several how to with search.
http://www.blogotechblog.com/2011/12/restore-motorola-droid-razr-to-stock-configuration/
Got this from here.
INSTRUCTIONS:
1. If you haven't already done so in the past, download and install the motorola usb drivers.
2. Download and install RSD Lite 5.6.
NOTE: In order for RSD Lite to recognize your phone, it has to be in AP Fastboot mode or it can just be booted up like normal. If your phone will not boot up, then power it off and put it into AP Fastboot mode by holding the volume up + down + power. Then select the AP Fastboot option.
3. Connect your phone to the computer with a usb cable and open RSD Lite. Make sure RSD Lite recognizes your phone before proceeding.
WARNING: Be careful not to move your phone around or mess with the usb cable while doing the following steps. You don't want to accidentally disconnect it. That might end up bad.
4. In RSD Lite, select the fastboot zip file you downloaded then press the "Uncompress and Start Flashing" button. RSD Lite will unzip the file and begin flashing.
5. Once the flashing is done and your phone is booted up, perform a factory reset to complete the process
http://www.razrforums.com/forum/droid-razr-development/775-rsd-lite-fastboot-not-working.html
http://forum.xda-developers.com/showthread.php?t=1486718&highlight=droid+razr+utility
Thanks! Will try that once i free
Do i need to factory reset b4 do this?
omnia1994 said:
Thanks! Will try that once i free
Do i need to factory reset b4 do this?
Click to expand...
Click to collapse
Dont think so because as with my other phones when I restored it automatically wiped the phone.
Ok. Will report once i tried! Many thx for everyone!
Back to stock successfully . Thx!
I followed the steps shown by blueis300
After connecting the device in APFastoot mode I started RSD lite it recognized my device.
Then I selected the zip file and selected the Uncompress and flash option
After Uncompressing the flashing process starts and when it reaches 6/18 it fails.
Please Help!!
any infomation about y it failed?
As soon as it enters step 6 it fails. I have no idea why its failing.
Please Help otherwise i'll be stuck with this stupid ROM
I live in India so is there any problem with the region or something??
r u sure u downloaded the correct rom?
I Got it!!!
Related
was going from gingerblur 2.5 on 1.56 then sbf to 1.83 and now it just says that after flashing.
tried to sbf 1.23 and 56 and same thing
am i doing something wrong?
in the rsdlite it sees the phone but says n/a for everything
Please HELP
Updated: I tried again fresh start on different computer and it worked!
must have been error in download, unzip, or there is something conflicting on my pc
hi i have same problem , went i flash OLYFR_U4_1.8.3_SIGNED_OLPSATTSPE_P013_HWolympus_1g_Service1FF.sbf ,
always after finish and rebooting then failed to boot 4 error raise,
i have use other computer to flash and the result is same failed to boot 4
i have install
- RSD Lite and 5.0
- Handset_USB_Driver_32_v4.9.0
plz can anyone help me ?
Sbf 4.1.26 or 4.1.57, then OTA to 4.1.83, root, sideload enable, flash CWM, flash GingerBlur.
bullghost said:
hi i have same problem , went i flash OLYFR_U4_1.8.3_SIGNED_OLPSATTSPE_P013_HWolympus_1g_Service1FF.sbf ,
always after finish and rebooting then failed to boot 4 error raise,
i have use other computer to flash and the result is same failed to boot 4
i have install
- RSD Lite and 5.0
- Handset_USB_Driver_32_v4.9.0
plz can anyone help me ?
Click to expand...
Click to collapse
i have the same problem
aaurnab said:
i have the same problem
Click to expand...
Click to collapse
please help
CaelanT said:
Sbf 4.1.26 or 4.1.57, then OTA to 4.1.83, root, sideload enable, flash CWM, flash GingerBlur.
Click to expand...
Click to collapse
thanks bro, i thinks that's the best way to update till 4.1.83,
here a little experience i have done
first time i try flash sbf 4.1.83 failed with that error booting,
and pull battery and back again to turn off the phone, and i flash the 1.26
then success with sim card inside,
iam not happy with failing on flash 4.1.83, then i thought the 4.1.83 sbf file is corrupt then i redownload again , after finish download,
i do the second time flashing with new 4.1.83 sbf
this second time is so frustrated, couz it fail again with same error.
until i have success full recover my atrix i do over 10 time flashing
and changing between computer and my notebook
and changing from windows 7 and windows XP
flashing random sbf from 1.83 and 1.26
the lasting i lost my hope , then suddenly the flash was success, WTF ,
lasting i remember is i pull the battery and pull out the sim card , then put back the battery, and do the flash,
the last time i flash 1.26 sbf
i thing
there is something no right with driver or RSD Lite not sync or missing something
until now iam still don't know how to solve it ,
pls anyone can find out what the problem and how to solve it
After about 4-5 hours and 7-8 tries using sfb method to upgrade to 1.83, I finally have a working phone again.
As to how I got stuck on the:
boot fail 4
starting RSD
and in RSD Lite, the phone's device name showing up as "SE Flash Olympus"
I decided to do a few things.
1. Go download the newest USB drivers. the 2.00.52 is what you should be on. If you can't find them, go to Motorola website and get MotoHelper 5.0 or whatever..install and then update your drivers. Restart your pc and keep trying to update your drivers until you get to USB 2.00.52 drivers.
2. USE THE ORIGINAL DATA CABLE THAT CAME WITH THE PHONE.
3. Make sure the connections are not loose at all (could've been why mine was messing up)
4. If you already have motohelper installed...go to the 'driverinstaller.exe' change operation mode to clean and reinstall, make sure the phone is unplugged. and click on start. (note, this part will be anywhere from 2 - 5 minutes depending on speed of your computer)
5. Restart RSD Lite, make sure you're using the latest one, and 'Run as administrator'.
**Go to config>Flash/Flex options... > only "check" Restart after Flexing..**
6. Now, I learned this the hard way...and many forums have it up there... GET YOUR BATTERY TO ABOVE 80% or IT WILL FAIL. (I had to go to a friend's at midnight to charge my battery from his atrix...hahaha)
7. Now turn your phone on again and it'll go to the "failed to boot 4 starting RSD" ...
8. Next, plug it in to your USB cable and click "Show Device" and then click once under the "USB 1 line" to view the device information at the top left. (Everything should be N/A except for your bootloader and you will also read "NS Flash Olympus now, instead of the SE Flash Olympus)
9. Put that '1.83_pudding.sfb' file in the "C:\ " directory to avoid any further complications.
10. Select the "...." browse to the '1.83_pudding.sfb' file and click start. It should work.... Now if it doesn't work... try and try again...
What I did was switched back and forth from 1.23 to 1.83... when I got mine to work, the device was registering as "SE Flash Olympus".
And for the longest time under bootloader, it would register as N/A...I finally decided to switch cables and it worked... once again, make sure to follow these:
* Full battery/80% above
* Stock Atrix USB cable
* 2.00.52 USB drivers
* RSD Lite 5.3.1
EDIT: GOOD LUCK! PM me if you need more assistance as those forward to XDA app
vash8806 said:
After about 4-5 hours and 7-8 tries using sfb method to upgrade to 1.83, I finally have a working phone again.
As to how I got stuck on the:
boot fail 4
starting RSD
and in RSD Lite, the phone's device name showing up as "SE Flash Olympus"
I decided to do a few things.
1. Go download the newest USB drivers. the 2.00.52 is what you should be on. If you can't find them, go to Motorola website and get MotoHelper 5.0 or whatever..install and then update your drivers. Restart your pc and keep trying to update your drivers until you get to USB 2.00.52 drivers.
2. USE THE ORIGINAL DATA CABLE THAT CAME WITH THE PHONE.
3. Make sure the connections are not loose at all (could've been why mine was messing up)
4. If you already have motohelper installed...go to the 'driverinstaller.exe' change operation mode to clean and reinstall, make sure the phone is unplugged. and click on start. (note, this part will be anywhere from 2 - 5 minutes depending on speed of your computer)
5. Restart RSD Lite, make sure you're using the latest one, and 'Run as administrator'.
**Go to config>Flash/Flex options... > only "check" Restart after Flexing..**
6. Now, I learned this the hard way...and many forums have it up there... GET YOUR BATTERY TO ABOVE 80% or IT WILL FAIL. (I had to go to a friend's at midnight to charge my battery from his atrix...hahaha)
7. Now turn your phone on again and it'll go to the "failed to boot 4 starting RSD" ...
8. Next, plug it in to your USB cable and click "Show Device" and then click once under the "USB 1 line" to view the device information at the top left. (Everything should be N/A except for your bootloader and you will also read "NS Flash Olympus now, instead of the SE Flash Olympus)
9. Put that '1.83_pudding.sfb' file in the "C:\ " directory to avoid any further complications.
10. Select the "...." browse to the '1.83_pudding.sfb' file and click start. It should work.... Now if it doesn't work... try and try again...
What I did was switched back and forth from 1.23 to 1.83... when I got mine to work, the device was registering as "SE Flash Olympus".
And for the longest time under bootloader, it would register as N/A...I finally decided to switch cables and it worked... once again, make sure to follow these:
* Full battery/80% above
* Stock Atrix USB cable
* 2.00.52 USB drivers
* RSD Lite 5.3.1
EDIT: GOOD LUCK! PM me if you need more assistance as those forward to XDA app
Click to expand...
Click to collapse
People 51_OLL iron-4.5.2A-lite 5.6 rsd 49_SIGNED_STABLE45LAOLYMPGBPERAR_P011_A026_M001_HWpd_Service1FF with ... and my error:
"Failde to boot 4"
rsd starting mode
I am reading is the battery problem that has to be for 80 %+...
If I turn on the power but the volume key + I fastboot protocol enters
If it lights only the error:
"Failde to boot 4" starting mode rsd
I can do twice the iron sbf with 2.3.6 official stock continues to give me the same error.
Lei may be because the battery is not 100% so fails.
How do I charge if the wall charger no load and light me alone with the legend:
"Failde to boot 4" rsd starting mode.
It can be for this, because this is not a 100% Bateias??
Another query may be that by command fastboot mode can be fixed??
So playing around with a modified Atrix rom... I am now locked. Trying to get the phone back up and running using the SBF and RSDLite but having problems getting the software to recognize the phone.
As the phone sits, it now reads at the initial boot.
Code:
Failed to boot 2
Starting RSD mode
I've tried to take it into recovery mode (created a nandroid backup already to the external microSD) without any luck.
I installed the atrix clockwork recovery (I thought I read somewhere that the atrix CWR worked on the X2) FAILED
Mine now reads same as the OP. Im having to redownload the SBF as Im on Vacation away from my PC that has everything on it.. SO, Ill post if I have additional issues
Hi, I am sorry you are having so much trouble. Hopefully I can provide the steps and help to guide you into successfully recovering your phone from this boot error.
From what I understand you're receiving the following error: "failed to boot 2. starting rsd mode"
I have encountered this error a few times while developing MinimalX. Fortunately, you should be able to recover this using the proper method.
First, turn off your device and plug it in. You will need a certain amount of battery life to perform an SBF without error, so, take advantage of these download times to increase your charge using a wall charger.
Next, you will need to download and install DX2 Drivers and RSD Lite.
You will also need the SBF file, which can be downloaded here:
SBF File
(note: be sure to unzip the file)
Once everything has downloaded and installed successfully, unplug your device from the USB. Plug your USB into your computer only. Then, run RSD Lite with administrator permissions. Browse to and select your SBF file (VRZ_MB870_DTN-14.8_1FF_01.sbf). Then turn on your device, and when you get the "starting RSD mode" prompt, plug in the usb cord from computer to phone. RSD Lite should then recognize your phone, and from there, simply, press start and leave the device and your computer alone until completion (not necessary, but extra precaution). Once this finishes and the phone boots, I highly recommend also doing a factory reset in settings > privacy.
I hope you the best and that this is able to restore function toyour phone. If you need any additional help, feel free to PM me or post in this thread.
Happy DROID-ing!
Sent from my DROID X2 using Tapatalk
Ran into this problem yesterday. Had issues with RSD Lite. Make sure you have the latest version or it will fail. Has to be version 5.3.1 and NOT 5.0 or whatever.
then it should work without a hitch.
Just a reminder, you will have your apps and stuff still installed including SuperUser. You will have to run Gingerbreak again to reroot to add the files back into the proper location, SuperUser doesn't work even with the .apk installed by itself. Just fyi.
Follow instructions here and download files from links provided...
http://forum.xda-developers.com/showthread.php?t=1175300
Yeah Don't Try And Flash The Atrix In Rom Manager, It Will Give You That Error Too.
Apparently there's a link floating around pointing to RSDLite 5.0 renamed and hacked to show 5.3.1. While the download says 5.3.1, the install says 5.3.1, it's still only 5.0.
Thanks again to those working to make the X2 a better phone. Perhaps we can get GB up and running on this thing before the OTA is released. Wouldn't that be egg-on-the-face.
just format the system from recovery, and does not start need help urgent!
someone know I can do?
what the phone do if you push these boutons :
Volume UP + Volume Down + Power . hold 5 sec ?
he boot or do nothing ?
Assuming you have an X912 (VZW CDMA RAZR)?
Download the fastboot files here
Download and install RSD Lite Here
Download and install Moto Drivers here
If you hold all 3 buttons on the side of the phone it should force a reboot and it'll kick you into the moto recovery bootloader. Select AP Fastboot.
For instructions on using RSD use the interwebz. Too much for me to type out.
Flash the recovery file via RSD.
That will return it back to factory (ver .744). You should get an update notification but if you want to pull it you can do that too.
when I try to flash with rds device settings are clean, and gives me error, any help?
cygnus56 said:
when I try to flash with rds device settings are clean, and gives me error, any help?
Click to expand...
Click to collapse
I told you. I'm lazy. Google knows.
http://www.droidforums.net/forum/dr...-using-rsd-lite-flash-sbf-file-correctly.html
thank you very much
cygnus56 said:
when I try to flash with rds device settings are clean, and gives me error, any help?
Click to expand...
Click to collapse
Which mode are you selecting when you boot the phone? Fastboot or something else?
fastboot and show me this https://motorola-global-eng.custhelp.com/rnt/rnw/img/enduser/spdrmain22.png
then start flashing and I get an error because I do not show any value as the imei
http://imageshack.us/photo/my-images/812/rsdlite3.png
in device properties only show me N/A... please i need help, this mobile is new!!!
It's not seeing a USB connection
Sent from my DROID RAZR using xda premium
Do not post questions in development forums
So I have been trying a bunch of different roms for the RAZR today and I was having problems with the keyboard not working. I decided to try to load CM9, so I read I need to use "safestrap" and not "bootstrap" that I had been using. I downloaded it, installed then tried to boot into recovery and load CM9.
Now the safestrap boot screen appears and says "safe system disabled" "hit search to continue / hit the menu button to boot into recovery" if I hit the menu button it just reboots, if I hit search the screen just goes blank and I have to do a reset to get it to start the process again.
I have RSD but I have never used it before. I have my phone plugged into my computer but my computer doesnt see it.
Help!
dreamsti said:
So I have been trying a bunch of different roms for the RAZR today and I was having problems with the keyboard not working. I decided to try to load CM9, so I read I need to use "safestrap" and not "bootstrap" that I had been using. I downloaded it, installed then tried to boot into recovery and load CM9.
Now the safestrap boot screen appears and says "safe system disabled" "hit search to continue / hit the menu button to boot into recovery" if I hit the menu button it just reboots, if I hit search the screen just goes blank and I have to do a reset to get it to start the process again.
I have RSD but I have never used it before. I have my phone plugged into my computer but my computer doesnt see it.
Help!
Click to expand...
Click to collapse
Whats your razr. Its verizon? If not you should use bootstrap.
Safestrap is for verizon razr. But some uses bootstrap on it.
You have to put ur razr in ap fastboot mode: power+vol up+vol down in order to flash with rsd lite
Choose a stock rom to your razr and flash it. Make sure flash correct rom
Cheers
Sent from my XT910 using Tapatalk 2
I have the Verizon RAZR.
So my computer does not recognize the phone when in AP Fastboot, but it does recognize it when its in BP SDF flash. What am I doing wrong?
dreamsti said:
I have the Verizon RAZR.
So my computer does not recognize the phone when in AP Fastboot, but it does recognize it when its in BP SDF flash. What am I doing wrong?
Click to expand...
Click to collapse
Uninstall all motorola software, reinstall motocast 1.29 or newer then connect ur razr.
Use rsd lite 5.7 and make sure you got correct sbf file
You may have corrupted drivers.
Cheers
Cheers
Enviado de meu XT910 usando o Tapatalk 2
Do I need to install anything else other than those 2 things? It still doesnt work.
Would having Samsung drivers effect anything? I have a Galaxy Nexus too.
dreamsti said:
Would having Samsung drivers effect anything? I have a Galaxy Nexus too.
Click to expand...
Click to collapse
Sometimes it brokes motorola drivers. Doing what I said should work.
Edit:
BTW what's the version you were and what's the version you're trying to flash?
Some versions cannot downgrade when the one you're trying to flash have a lower security.
I was running Gummy when everything went wrong. Loading safestrap is when I started having the current problems.
I uninstalled the Samsung drivers, and loaded both RSDLite 5.7 and the Moto driver you suggested and RSD will not see my phone in AP Fastboot, but it will when in BP SDF flash. Very confusing.
I will load the latest version of GB when I can get my computer to see my phone in AP Fastboot.
Now my computer is trying to install the flash MZ600 driver and error's out. I googled MZ600 and it says its a Xoom driver???
dreamsti said:
Now my computer is trying to install the flash MZ600 driver and error's out. I googled MZ600 and it says its a Xoom driver???
Click to expand...
Click to collapse
Yup. You've a driver problem, better unistall others devices you may have.
Or, do it in other pc, like a notebook.
So I finally got the drivers working and now RSD see's my phone when in AP Fastboot, but I get an error when flashing the file. This is the error I get.
"Failed flashing process. 22/23 flash "radio.img" -> Phone returned FAIL."
It was flashing for about 5 minutes before I got this error.
Edit: I'm using the file from this thread.
http://rootzwiki.com/topic/13566-droid-razr-fastboot-file/
Blur_Version.6.12.173.XT912.Verizon.en.US
I think the battery went dead, ugh. Ill recharge and report back.
This is kind of different from random reboots, because no matter what I am doing on the device or if its ideal, it does reboot around every 3 minutes.
Current version is 4.0.4 and the model of the device is Verizon xt912
System version: 6.16.211.xt912.Verizon.en.US
Kernel version: wt-3.0.0
Build no.: 6.7.2-180 ....
Build date: Jun 14, .... 2012
Another thing is, under the settings, the device is showing Baseband and IMEI - Unknown. Don't know what may have caused this. BTW, currently I am out of country (US) and I have no SIM inserted in the slot (for international GSM), I don't suppose inserting no SIM can lead to base band and IMEI = unknown?
I am no idea if this Unknow Baseband and IMEI is causing the reboot or vice-versa or if there's dependence.
What I have tried:
Wiping Cache through recovery
Reset to factory settings
Option 1 of Matt's Razr Utility 1.82
If anyone can tell me how can I make this phone usable, I would be thankful.
Did you try flashing official FXZ using RSD lite ?!
Sent from my DROID RAZR using Tapatalk 2
ryan8r said:
Did you try flashing official FXZ using RSD lite ?!
Sent from my DROID RAZR using Tapatalk 2
Click to expand...
Click to collapse
Not really, but would it be any different than restoring to ICS .211 using Matt's Razr Utility?
Can you tell me where I can find the official FXZ for Razr to flash?
It will be different cause stock fxz includes every part of the firmware while matts utility can only install certain parts of it like the system, boot etc.
The RSD simply doesn't detect the device. USB drivers are installed and gets detected fine with Matt's Razr Utility.
Tried different RSD versions. I also tried replacing all the radio, system, boot img and all other files in the Matt's Razr Utility with the FXZ which I was trying to restore back to. It said it did successfully flashed to 211 but the problem is still there.
I think if there's any way to change the base band from Unknown to the original, this problem can be corrected. Any ideas for this?
I cant say why RSD wont detect your device but "Baseband unknown" could be a Bad ESN or a blocked device and a corrupt PDS partition in the worst case..
That said if you do have any of the above your CDMA.XX.XXX baseband is most probably useless what you could try is to get your device to switch to a GSM baseband N.01.XXX and make use of the device with any operational GSM service in your country.
In order to do that root your device install Safestrap and flash any of the GSM roms available.
Try that and tell me the results.
Sent from my DROID RAZR using Tapatalk 2
^
I'll try that and let you know.
While trying to get it to work, I cannot find the EFS folder. I am using Android Commander on PC to browse the files and folders of the device. Its right at the very root, i.e at the location " / " right? Where there are folders like Sys, System, Root, preinstall, preoc etc
You've installed motorola usb drivers,
When the phone is powered off, hold both VOLUME UP + DOWN buttons and press POWER button. You'll get into bootmenu. Release the buttons and navigate with VOLUME DOWN to AP FASTBOOT mode, press VOLUME UP to get into AP FASTBOOT MODE. Connect the phone to pc, launch RSD Lite ( newest version 6.1.4 )
If it detects the phone, flash stock xt912 ics rom.
Semseddin said:
You've installed motorola usb drivers,
When the phone is powered off, hold both VOLUME UP + DOWN buttons and press POWER button. You'll get into bootmenu. Release the buttons and navigate with VOLUME DOWN to AP FASTBOOT mode, press VOLUME UP to get into AP FASTBOOT MODE. Connect the phone to pc, launch RSD Lite ( newest version 6.1.4 )
If it detects the phone, flash stock xt912 ics rom.
Click to expand...
Click to collapse
I don't know why but the RSD lite does not detect the phone. USB drivers are installed and working fine because matt's razr utility detects the phone (before it wasn't).
You may need to run RSD Lite as Administrator for it to work on Win 7/8.
You need to get it to successfully complete flashing the radios in recovery after it finishes the other partitions.
It should reboot into recovery by itself and flash the BP.img and LTE.img and then reboot again normally after it has completed.
That should fix the Baseband unknown and blank IMEI issue.
cellzealot said:
You may need to run RSD Lite as Administrator for it to work on Win 7/8.
You need to get it to successfully complete flashing the radios in recovery after it finishes the other partitions.
It should reboot into recovery by itself and flash the BP.img and LTE.img and then reboot again normally after it has completed.
That should fix the Baseband unknown and blank IMEI issue.
Click to expand...
Click to collapse
I am on Win 7 64 bit.
Running as Admin, but still RSD Lite does not show the device. Is there anything else that I can try?
I'll also try running on a different PC.
http://db.tt/EMFh9jos
That is RSD Lite 6.1.4 the latest available version. Try it and see if you have any better results.
Can you use ADB ?!
And Did you try any of the GSM roms ?!
Accidentally Sent from my iPhone using Tapatalk
cellzealot said:
http://db.tt/EMFh9jos
That is RSD Lite 6.1.4 the latest available version. Try it and see if you have any better results.
Click to expand...
Click to collapse
I am using 6.1.4 and have also tried 5.9. Anything else that I can try?
ryan8r said:
Can you use ADB ?!
And Did you try any of the GSM roms ?!
Accidentally Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
No. I think I'll try that.
I am uploading a zip file that is just the radio_update_211_RAZR.zip in the radio.img from the 211 FXZ.
You will need to put the file on the root of your sdcard. Since the phone isn't booting, the easiest way is to take out the sdcard and put it in a card reader on your PC to transfer the file. Then reinsert the sdcard in your phone and reboot the phone holding Vol up and down + PWR to get to the boot menu and select recovery.
The phone will boot to M logo and then blank screen briefly and then show the stock recovery with Android and red Exclamation !. Press both Vol up and down at the same time to enter recovery and chose Apply Update from External Storage option and browse to the update_radio_211_RAZR.zip and select it.
It should load lte.img and bp.img and then reboot automatically.
This should allow the phone to boot normally and display the baseband and IMEI again if everything works as described.
https://dl.dropbox.com/u/7632904/update_radio_211_RAZR.zip
This will avoid the need for RSD Lite if it works. If not, then you can try using fastboot to manually flash the images from the FXZ.
press all three bttn,on black and white menu scroll down and select "BP HW Diag & Boot AP" boot will boot up ,see if phone restarts on its on or not and lemme know ...
cellzealot said:
I am uploading a zip file that is just the radio_update_211_RAZR.zip in the radio.img from the 211 FXZ.
You will need to put the file on the root of your sdcard. Since the phone isn't booting, the easiest way is to take out the sdcard and put it in a card reader on your PC to transfer the file. Then reinsert the sdcard in your phone and reboot the phone holding Vol up and down + PWR to get to the boot menu and select recovery.
The phone will boot to M logo and then blank screen briefly and then show the stock recovery with Android and red Exclamation !. Press both Vol up and down at the same time to enter recovery and chose Apply Update from External Storage option and browse to the update_radio_211_RAZR.zip and select it.
It should load lte.img and bp.img and then reboot automatically.
This should allow the phone to boot normally and display the baseband and IMEI again if everything works as described.
https://dl.dropbox.com/u/7632904/update_radio_211_RAZR.zip
This will avoid the need for RSD Lite if it works. If not, then you can try using fastboot to manually flash the images from the FXZ.
Click to expand...
Click to collapse
ii m having exact same problem as listed by op , i tired flashing this zip file following error came up on screen
assert failed: motorola.motoflash(" /tmp/bp.img")
E:error in /tmp/sideload/package.zip
(status 7)
Installation aborted.
cellzealot said:
I am uploading a zip file that is just the radio_update_211_RAZR.zip in the radio.img from the 211 FXZ.
You will need to put the file on the root of your sdcard. Since the phone isn't booting, the easiest way is to take out the sdcard and put it in a card reader on your PC to transfer the file. Then reinsert the sdcard in your phone and reboot the phone holding Vol up and down + PWR to get to the boot menu and select recovery.
The phone will boot to M logo and then blank screen briefly and then show the stock recovery with Android and red Exclamation !. Press both Vol up and down at the same time to enter recovery and chose Apply Update from External Storage option and browse to the update_radio_211_RAZR.zip and select it.
It should load lte.img and bp.img and then reboot automatically.
This should allow the phone to boot normally and display the baseband and IMEI again if everything works as described.
https://dl.dropbox.com/u/7632904/update_radio_211_RAZR.zip
This will avoid the need for RSD Lite if it works. If not, then you can try using fastboot to manually flash the images from the FXZ.
Click to expand...
Click to collapse
It says, Finding, Opening, Verifying, Installing update....
assert failed: motorola.motoflash("/tmp/bp.img")
E:Error in /tmp/sideload/package.zip
(Status 7)
Installation aborted.
BTW, I tried this when being on 215.
Should I go to 211 and then try again?
karansawhney said:
press all three bttn,on black and white menu scroll down and select "BP HW Diag & Boot AP" boot will boot up ,see if phone restarts on its on or not and lemme know ...
Click to expand...
Click to collapse
In BP HW Diag & Boot AP, it does not reboot on its own.
lamborg said:
It says, Finding, Opening, Verifying, Installing update....
assert failed: motorola.motoflash("/tmp/bp.img")
E:Error in /tmp/sideload/package.zip
(Status 7)
Installation aborted.
BTW, I tried this when being on 215.
Should I go to 211 and then try again?
In BP HW Diag & Boot AP, it does not reboot on its own.
Click to expand...
Click to collapse
so both of us are in a same boat my phone acts the same and if i use matts utility i file gets created everytime in my phones internal storage named "update_radio.zip.failure"
If you're using BMM or SAFESTRAP 3.10 with stock ROM flashing enabled I can make you a flashable patch that will allow GSM services to work on the stock ROM itself !?
I'm only trying to help cause I've owned 2 RAZR's previously with the same condition. As I stated earlier if a radio flash or FXZ doesn't fix it then it is a corrupt PDS partition and it cannot be fixed to work on the CDMA baseband.
Sent from my DROID RAZR using Tapatalk 2