I have a modded aria with the stock 2.2.2 rom on it.
recently I've been using skullcandy earbuds for my phone with the microphone built in and peoplei talk too have been saying that they can't hear me or have been having difficulty hearing me.
I don't believe it's the headphones but I'm sure that it is most likely is the hardware or software in the phone is there any remedy to this?
Have you tried cleaning out the headphone jack? Lint can get stuck in there and prevent a good connection with headsets because headset plugs are longer than regular headphone plugs. A toothpick seems to work well for me.
drumist said:
Have you tried cleaning out the headphone jack? Lint can get stuck in there and prevent a good connection with headsets because headset plugs are longer than regular headphone plugs. A toothpick seems to work well for me.
Click to expand...
Click to collapse
I did and it still isn't working (saw a similar post but wasn't the same)
Wasn't sure if maybe software maybe the problem or if its just the hard ware
I tried another pair of headphones and same thing
Only thing I could try was rebooting and leaving it off for a little bit but it didn't work
Any ideas would be nice
I don't really know what might cause that in software. If I was having that issue I'd probably make a nandroid backup, then do a factory reset to see if the problem goes away or not.
Related
I'm not sure if this has to do with the x2 or just cm7 but I can't seem to figure it out. The audio without headphones is perfectly fine, but with them only the instrumental parts can be heard occasionally you can hear kind of a digital chirp of the vocals.tried figuring it out in dsp and music settings but nothing. Any advice on this is very much appreciated.
Sent from my DX2 w/Cm7 using XDA App
No problems with or without my headphones under CM7. Maybe your headphone port is bad?
Have you tried hooking up a different pair of headphones to see if it might be the headphones or the connector?
Have you tried it under a different ROM to see if you're getting the same problem?
Is this something that you only experience when listening to music with your headphones? Try checking the audio port to see if its got any lint in it. You can clear it out with a paperclip and you might be surprised to see how much has built up. It'd also be a good idea to test your phone with other headphones.
If this is happening with/without headphones, I'm not sure what would cause this. Maybe try a different music player?
It's happening to me, only on CM7
Skelente said:
Is this something that you only experience when listening to music with your headphones? Try checking the audio port to see if its got any lint in it. You can clear it out with a paperclip and you might be surprised to see how much has built up. It'd also be a good idea to test your phone with other headphones.
If this is happening with/without headphones, I'm not sure what would cause this. Maybe try a different music player?
Click to expand...
Click to collapse
This happened to my Inspire 4G with CM7.1. The problem dissappeared upon installing ICS with aospX and kept working fine with IceColdSandwich, but several other problems forced me to return to Gingebrear. Now with CM 7.2 the problem is again.
It is not a total attenuation. It is a DSP setting that seems to be optimized for karaoke, because it selectively suppresses voice frequencies. However, all settings in DSP manager are turned off. Turning on Stage Virtual Room barely improves it. I can hear some voices, but really bad.
I think it's probably your headphones wearing out. I had a similar problem and a new pair of headphones immediately fixed the issue.
you got a case on that phone? I stopped using my otterbox 'cause every time i plugged in headphones, they'd act very stupid (sometimes giving the "no vocals" thing, sometimes cutting in and out)
I've also noticed that some headphone jacks don't do a good job of locating themselves and you can actually push them too far in.
I use a set of samsung headphones that have four contacts on the 3.5mm jack instead of the typical Tip-ring-sleeve three contact design. these are the ONLY headphones I have used that give me zero problems (unless I use the otterbox case along with them)
between the stupid angle on the hole for the 3.5mm jack on the phone, and a plethora of minute differences between jack designs, generally the X2 and headphones are a marriage made in hell...
stereo bluetooth works perfectly however
I seem to have a weird problem with my headphone jack. I have a pair of Philips O'Neil headphones that up until the plug broke worked great with the TF101. I got a new cord and now the TF101 will not recognize the headphones when plugged in??? The new cord works in all other mp3 tabs I have tried it in so the cord is good. I have also tried different brands of cords and still no luck. It will work with ear buds that have a mic i.e. iPhone headphones or the ear buds from my Galaxy tab but not any other regular headphones. Any idea why this is? I tried a hard reboot and am contemplating a factory reset.
TIA
JC
Hmm, did you do a firmware update recently? That might have randomly broken the functionality.
Thing O Doom said:
Hmm, did you do a firmware update recently? That might have randomly broken the functionality.
Click to expand...
Click to collapse
I may have. I know when I went to do a TB so I could wipe it, TB said it could not obtain root. It was rooted before. I'll look into that.
Sent from my HTC Sensation 4G using xda premium
tu3712 said:
I seem to have a weird problem with my headphone jack. I have a pair of Philips O'Neil headphones that up until the plug broke worked great with the TF101. I got a new cord and now the TF101 will not recognize the headphones when plugged in??? The new cord works in all other mp3 tabs I have tried it in so the cord is good. I have also tried different brands of cords and still no luck. It will work with ear buds that have a mic i.e. iPhone headphones or the ear buds from my Galaxy tab but not any other regular headphones. Any idea why this is? I tried a hard reboot and am contemplating a factory reset.
TIA
JC
Click to expand...
Click to collapse
I found a solution, although not the one I want, it will work. There is an app called toggleheadset2 that forces the sound to go to the headphone jack. I get sound through the head phones again. Weird i have to do this but like the post above it could have been a firmware update.
Thanks
So I installed Neutrino on my Atrix yesterday (I'm not sure if that's relevant or not, but I figure it's good to know), and everything was working perfectly fine. However, earlier today the audio from my headphone jack started to sound completely distorted.
It's not the earbuds, because they work on other devices I have. And the audio from my speakers and from HDMI works perfectly fine.
Has anyone had this problem, and if so, is there any way I can fix it? Or is my phone screwed?
Did you play with equalizer settings any (DSPmanager or similar)?
I didn't. At least, not at first.
DSP Manager actually started to crash on startup about the same time that the audio from my headphones would be a problem. I thought reinstalling it would fix the problem, but it hasn't. Though, the louder I make it, the more "clearly" I can hear what I'm playing (it still sounds like satan farts, though).
I also tried cleaning the headphone jack, but that only helped a slight bit.
Would it be worth reinstalling Neutrino or is my phone died?
I'd say it's worth a shot. Make a nandroid, do a full wipe, and then flash your ROM. If that doesn't help, then at least you can be fairly sure it's not the software.
So I'm bumping this, with a little bit more information of what I've tried and what my problem is.
I've tried uninstalling and reinstalling DSPManager. Didn't work.
I made a Nandroid backup, did a full wipe, and tried to play music again. Didn't work.
I actually tried to install Beats Audio Drivers to see if they would help. They didn't.
This is what my phone's audio jack currently sounds like, without the high-pitched humming so pardon me if your ears hurt.
http://soundcloud.com/user587656353/i-want-you-back-almost-kinda
I actually tried cleaning the inside of my headphone jack and it seemed to help ever so slightly.
Would this mean my headphone jack is toast or does anyone else have any ideas what the problem could be?
hellothar said:
So I'm bumping this, with a little bit more information of what I've tried and what my problem is.
I've tried uninstalling and reinstalling DSPManager. Didn't work.
I made a Nandroid backup, did a full wipe, and tried to play music again. Didn't work.
I actually tried to install Beats Audio Drivers to see if they would help. They didn't.
This is what my phone's audio jack currently sounds like, without the high-pitched humming so pardon me if your ears hurt.
http://soundcloud.com/user587656353/i-want-you-back-almost-kinda
I actually tried cleaning the inside of my headphone jack and it seemed to help ever so slightly.
Would this mean my headphone jack is toast or does anyone else have any ideas what the problem could be?
Click to expand...
Click to collapse
I'm not sure, but it sounds like what you're hearing is the difference between the 2 channels, rather than the channels themselves. This would happen if the common ground connection is broken somewhere in the audio out. It's an easy theory to test really. All you need is an audio file that plays on either the left or right channel only. If you have sound out of both channels, then there's your problem, if not, then it's something else.
Actually, this sounds like a poor connection that is overcompensated by extreme loudness so that some of the electric current is strong enough to pass through. I've heard what the "no common ground" sounds like many times, I don't think this is it.
The headphone connector is not actually soldered to the PCB but instead sits on it on springy contacts (makes for very easy repairs and replacements at service centers). I'm almost willing to bet there lies your problem.
ravilov said:
Actually, this sounds like a poor connection that is overcompensated by extreme loudness so that some of the electric current is strong enough to pass through. I've heard what the "no common ground" sounds like many times, I don't think this is it.
The headphone connector is not actually soldered to the PCB but instead sits on it on springy contacts (makes for very easy repairs and replacements at service centers). I'm almost willing to bet there lies your problem.
Click to expand...
Click to collapse
Maybe. But if that is the case, wiggling the plug may give some indication of that without disassembling the device, just as would playing a single channel file. In both cases, the jack would likely be the culprit, but given how fragile the device is internally, taking it apart should be done with extreme caution.
lehjr said:
Maybe. But if that is the case, wiggling the plug may give some indication of that without disassembling the device, just as would playing a single channel file.
Click to expand...
Click to collapse
True. I wouldn't recommend digging into disassembling the phone right away, not before exploring other possibilities. Because...
lehjr said:
given how fragile the device is internally, taking it apart should be done with extreme caution.
Click to expand...
Click to collapse
...this.
I tried playing a mono sound file, and sound files that play through only the left speaker and only the right speaker. They all sound like they have the same problem, so we can rule that out.
Though, I will mention that the sound that is heard is on maximum volume, and that's the only time I can hear anything at all. If I go down just two notches, then I start to hear nothing.
hellothar said:
I tried playing a mono sound file, and sound files that play through only the left speaker and only the right speaker. They all sound like they have the same problem, so we can rule that out.
Though, I will mention that the sound that is heard is on maximum volume, and that's the only time I can hear anything at all. If I go down just two notches, then I start to hear nothing.
Click to expand...
Click to collapse
Just a thought, but have you tried another pair of headphones?
Edit: if the headphones are good, then the only other thing I can think of is a bad section in the audio chip. The schematic shows the headphone output is separate from any of the other sound outputs, so it is possible that the chip is bad. Unfortunately, if that is the case, the cheapest solution would be to replace the main board, but it's a delicate procedure.
Edit 2:
Before giving up, this thread might help.
lehjr said:
Just a thought, but have you tried another pair of headphones?
Edit: if the headphones are good, then the only other thing I can think of is a bad section in the audio chip. The schematic shows the headphone output is separate from any of the other sound outputs, so it is possible that the chip is bad. Unfortunately, if that is the case, the cheapest solution would be to replace the main board, but it's a delicate procedure.
Edit 2:
Before giving up, this thread might help.
Click to expand...
Click to collapse
Yeah, I'm sure it's not the headphones. I've got two; a set of headphones and a set of ear buds. Both of them are functional in other devices but do not work in the phone. Also, the audio clip was direct feed with a different chord, so the problem is surely with the phone.
I'm at the point where I'm willing to open up the phone to see if there is a problem with the jack itself. If it is corrosion or another problem with the jack then I can try some repairs. If I do have to replace the main board then I'll probably wait on that and ultimately purchase a new phone.
One thing to note is that the audio quality does not improve if I move the jacks around inside of it. However, I do hear a sort of rubbing sound from the headphones if I am moving it around.
hellothar said:
Yeah, I'm sure it's not the headphones. I've got two; a set of headphones and a set of ear buds. Both of them are functional in other devices but do not work in the phone. Also, the audio clip was direct feed with a different chord, so the problem is surely with the phone.
I'm at the point where I'm willing to open up the phone to see if there is a problem with the jack itself. If it is corrosion or another problem with the jack then I can try some repairs. If I do have to replace the main board then I'll probably wait on that and ultimately purchase a new phone.
One thing to note is that the audio quality does not improve if I move the jacks around inside of it. However, I do hear a sort of rubbing sound from the headphones if I am moving it around.
Click to expand...
Click to collapse
If the jack is the issue then it shouldn't be too bad to replace. I was looking at different websites earlier and they look to be really cheap. The thing I have to stress though is just be careful, and don't take apart the phone unless you can replace the phone itself just in case something should go horribly wrong. I know that should be pretty obvious, and generally people tend to underestimate their own skill level, but I have encountered a few people in my time who have what I consider to be the opposite of the Midas touch, and their attempts at repairing anything end up as more of a hate crime against the very thing they are trying to fix.
Hello there.
Today I've noticed that the left speaker of my headphones doesn't work when I plug them to my Mini Pro. I moved from CM10.2 to SJB 8.0 and found this out while testing stuff out. It's been some time since I've used my phone as a music player last time, but I never had any problems like this. Reverting to CM didn't help either.
I can't really find out whether this is a hardware or software issue. I think connector isn't dirty, wiggling the plug doesnt make any difference. Is there anything more I can try, besides flashing stock firmware? Did anybody have a similar problem?
EDIT: I've connected my PC to the phone as a BT headset, both channels work fine there.
What headphone do you own? Most new headphones with mic won't work correctly on 2011 xperia. Those new headphones use CTIA, our phone uses OMTP. Long story short, you can only use stock headset or the ones without mic. You could buy OMTP to CTIA converter though. Look up on eBay.
fundre said:
What headphone do you own? Most new headphones with mic won't work correctly on 2011 xperia. Those new headphones use CTIA, our phone uses OMTP. Long story short, you can only use stock headset or the ones without mic. You could buy OMTP to CTIA converter though. Look up on eBay.
Click to expand...
Click to collapse
I use only standard stereo headsets, namely Creative Aurvana Live and Creative EP630.
They looked compatible to me. Maybe cleaning phone jack with alcohol would help, I don't know. Sorry
fundre said:
They looked compatible to me. Maybe cleaning phone jack with alcohol would help, I don't know. Sorry
Click to expand...
Click to collapse
Thanks for your input either way. I have tried cleaning the jack with isopropyl alcohol, and also just in case left the phone without battery for some time (because why not).
The strange thing about this is I'm getting absolutely no sound whatsoever on the left channel, while the right one works like a charm. If i'd get any noise while moving the jack around, it would be pretty obvious sign of bad soldering, and therefore a HW problem.
I still struggle with this problem. I have tried downgrading software to stock GB, didn't help. I've took it to some service centre, the folks there have replaced the jack, but it didn't help either. I wonder if i should pump any more money into this.
I just bought this phone 2 months ago. It's running well until now. But I have a problem, my phone can't connect to several audio jack. I mean, it can't be connected to Samsung's earphone and my car entertainment audio jack. Can someone solve this problem?
Thankyou
Try to clean the headphone jack port (e.g. with a needle). It may have some dust in it preventing a proper connection.
AlvinWahracha said:
I just bought this phone 2 months ago. It's running well until now. But I have a problem, my phone can't connect to several audio jack. I mean, it can't be connected to Samsung's earphone and my car entertainment audio jack. Can someone solve this problem?
Thankyou
Click to expand...
Click to collapse
have you ruled out the audio cables? Id suggest taking a bit of cotton of an ear swab and cleaning in there.
civicsr2cool said:
have you ruled out the audio cables? Id suggest taking a bit of cotton of an ear swab and cleaning in there.
Click to expand...
Click to collapse
Yes I have, do you mean that I should clean my phone audio port?
This happens, where one product accessory conflicts with another product. Looks the same, feels the same, not the same. I had an Xperia X10 since it came out till (well still have it) I bought this last month and so far so great. To your question/s, try another cable/connection. Like I said X10 had a separate accessory for different headsets, which had a male tip on the one end and a button +mic female tip for the other which made it easier for me to choose between earbuds or headsets. It worked on the iPhone and and The Compact Z3 but does not work on the Z5C. I did happen to have an extension from another blah blah blah but no button/mic part which doesn't bother me since I still use my phone like it was still hanging from a wall, phone in hand next to ear lol. It also work on one kind Samsung but didn't on two other kinds of Samsungs. So yea try another connector.