I Downloaded and installed the ICS update last night and have been living in hell since. It doesn't have the soft buttons it is supposed to, so navigating through everything is an absolute nightmare! I want to go back to my standard rooted phone. But I have followed MANY, MANY guides, and it will not work. I have downloaded 10 different ROMS and FIRMWARES today and Flashed OVER AND OVER. I am completely stuck and NEED help please.
I have used Recovery to try and install new Roms, Used Odin as well, and I get problems EVERY time. It will reboot, load, and as soon as the "Touch the Android to Begin" logo comes up, It starts having process failures popping up over and over, preventing me from being able to do anything. Forcing me to reflash to ICS again.
Can someone please explain the process to take it back to stock so I can re-root it?
Did you wipe everything when you installed the roms? Data, cache, Dalvik?
Find stock roms here for odin:
http://forum.xda-developers.com/showthread.php?t=1075278
Just make sure to download and install the correct rom depending on which SGSII you have.
xfile102 said:
I Downloaded and installed the ICS update last night and have been living in hell since. It doesn't have the soft buttons it is supposed to, so navigating through everything is an absolute nightmare! I want to go back to my standard rooted phone. But I have followed MANY, MANY guides, and it will not work. I have downloaded 10 different ROMS and FIRMWARES today and Flashed OVER AND OVER. I am completely stuck and NEED help please.
I have used Recovery to try and install new Roms, Used Odin as well, and I get problems EVERY time. It will reboot, load, and as soon as the "Touch the Android to Begin" logo comes up, It starts having process failures popping up over and over, preventing me from being able to do anything. Forcing me to reflash to ICS again.
Can someone please explain the process to take it back to stock so I can re-root it?
Click to expand...
Click to collapse
first install stock rom from this link
http://forum.xda-developers.com/showthread.php?t=1075278
then download this rom (i think this is best ICS Rom) and install it with CMW(you should copy the rom inside your internal SD) then full wipe your phone and install rom .
http://forum.xda-developers.com/showthread.php?t=1451346
it isn't hard to push thanks button
All you need to do, if having FCs is perform a factory reset (via recovery)...
Sent from my GT-I9100 using Tapatalk
xfile102 said:
I Downloaded and installed the ICS update last night and have been living in hell since. It doesn't have the soft buttons it is supposed to, so navigating through everything is an absolute nightmare! I want to go back to my standard rooted phone. But I have followed MANY, MANY guides, and it will not work. I have downloaded 10 different ROMS and FIRMWARES today and Flashed OVER AND OVER. I am completely stuck and NEED help please.
I have used Recovery to try and install new Roms, Used Odin as well, and I get problems EVERY time. It will reboot, load, and as soon as the "Touch the Android to Begin" logo comes up, It starts having process failures popping up over and over, preventing me from being able to do anything. Forcing me to reflash to ICS again.
Can someone please explain the process to take it back to stock so I can re-root it?
Click to expand...
Click to collapse
Why don't people search...?
http://forum.xda-developers.com/showthread.php?t=1449771
Kaze105 said:
Did you wipe everything when you installed the roms? Data, cache, Dalvik?
Find stock roms here for odin:
http://forum.xda-developers.com/showthread.php?t=1075278
Just make sure to download and install the correct rom depending on which SGSII you have.
Click to expand...
Click to collapse
@Kaze & @Medhi, I went to the Link you provide above, which is INCREDIBLY well laid out and helppful, If I lived anywhere in the world except The US. There arent any Firmwares provided for North America there. Any other suggestions? That was a great resource if they only had some North America Help
xfile102 said:
@Kaze & @Medhi, I went to the Link you provide above, which is INCREDIBLY well laid out and helppful, If I lived anywhere in the world except The US. There arent any Firmwares provided for North America there. Any other suggestions? That was a great resource if they only had some North America Help
Click to expand...
Click to collapse
Use any version... It is universal! Stop complaining and use search MORE OFTEN!
Sent from my GT-I9100 using xda premium
Phistachio said:
Why don't people search...?
http://forum.xda-developers.com/showthread.php?t=1449771
Click to expand...
Click to collapse
Phistachio!!! Thank You. And to reply, I most certainly DID search, MANY, MANY topics. I thought my phone was bricked but came across SOOOO many threads saying if your phone would load into a ROM it is most certainly NOT BRICKED, leading a n00b such as myself to believe I needed to search for a different issue. Always helps to know what you are looking FOR when searching. This looks awesome. I will try it right away and get back to you with an update as to whether this fixes it.
Phistachio said:
Why don't people search...?
http://forum.xda-developers.com/showthread.php?t=1449771
Click to expand...
Click to collapse
Phistachio - I followed your link, but when you get to the following step:
4) Download the necessary files : the Kernel, the Recovery Package and the Bootloader (it's the old one, which you can easily use a USB JIG to reset the counter and remove the yellow triangle when having a custom kernel or OS),
The link provided for the Recover Package is a Hotfile.com link, and the Archive that it downloads is PASSWORD PROTECTED, and there is no mention of a password anywhere on the page you provided, nor on the hotfile.com page.
Any Ideas?
zylor said:
Use any version... It is universal! Stop complaining and use search MORE OFTEN!
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Zylor, Thanks for the overt Negativity in your post. I was making sure we were clear, not complaining. I wasn't aware that telling someone that they have provided a great resource was "complaining". And when the OP AND the page he sends you to VERY CLEARLY say ONLY USE THE CORRECT VERSION, far be it for me to magically know that I can grab any random version from CHINA or wherever and have it work on my US ATT GS2. Sorry for trying to follow instructions and avoid a potential brick. But thanks for being a hateful Troll.
xfile102 said:
Phistachio - I followed your link, but when you get to the following step:
4) Download the necessary files : the Kernel, the Recovery Package and the Bootloader (it's the old one, which you can easily use a USB JIG to reset the counter and remove the yellow triangle when having a custom kernel or OS),
The link provided for the Recover Package is a Hotfile.com link, and the Archive that it downloads is PASSWORD PROTECTED, and there is no mention of a password anywhere on the page you provided, nor on the hotfile.com page.
Any Ideas?
Click to expand...
Click to collapse
Password is probably samfirmware.com or [email protected]
Are you sure you've got an I9100 and not an I9100G or whatever?
Sent from my Samsung Galaxy S II using Tapatalk.
mbutandola said:
Are you sure you've got an I9100 and not an I9100G or whatever?
Click to expand...
Click to collapse
Actually, you may be able to help me there. Most site reference only the I9100 or the I9100G. My Phone Hardware has a sticker saying SGH-I777, but the boot screen has always said GT-I9100. So which would it be?
xfile102 said:
Actually, you may be able to help me there. Most site reference only the I9100 or the I9100G. My Phone Hardware has a sticker saying SGH-I777, but the boot screen has always said GT-I9100. So which would it be?
Click to expand...
Click to collapse
You have the AT&T device.
Your correct forum is at http://forum.xda-developers.com/forumdisplay.php?f=1301
Not sure from the details supplied, but have youtried AT&T specific Roms?
Over at this site http://galaxys2root.com/category/att-galaxy-s2-roms/ (Thanks to Max) they have quite a few to try. And make sure you do a complete wipe before you flash one of them ie, factory reset, clear cache then advanced delvik cache and battery stats and then install from zip.
Hope this helps.
I followed all the instructions, and my phone rebooted into the ROM. But it is not stock. My Back and Search buttons still do not work, and the Recovery is 3e, so I cant use the Recovery function because my model (US AT&T) doesn't have the OK button. Since I cant get it to take a screenshot, i'll list the info below:
Android Version: 2.3.5
Baseband Version: I9100XXKI3
Kernel Version: 2.6.35.7-I9100XXKI3-CL577579 [email protected] #2
Build Number: GINGERBREAD.XXKI3
I just want to get it back to AT&T Stock, or a WORKING 2.3.6. But as it stands, It doesnt work properly, because my Back Button does not work, nor my Search button.
All Guidance is appreciated. I want to get back to the Stock Bootloader, not the ICS Bootloader
P.S. - I DID SEARCH FOR THIS INFO. When I did, I came up with threads like:
http://forum.xda-developers.com/showthread.php?t=1317372
- Turns out it only works on the CHINESE SGS2.
Bobgnarley said:
Not sure from the details supplied, but have youtried AT&T specific Roms?
Over at this site http://galaxys2root.com/category/att-galaxy-s2-roms/ (Thanks to Max) they have quite a few to try. And make sure you do a complete wipe before you flash one of them ie, factory reset, clear cache then advanced delvik cache and battery stats and then install from zip
Click to expand...
Click to collapse
Bob!! Thats exactly what I want to do. But I cant, because the Recovery installed on my phone wont let me do anything because I dont have the OK button on my phone. I tried the power button and everything else, I cannot make selections in Recovery 3e, so the only way to get out of it is to pull the battery.
Xfile if your sticker says at&t sgh-i777 theres a complete forum dedicated to that model here in xda. Better pop in there and find more help.
They also have model specific roms over there and surely they should work. Wannit to post the link but not sure how to from the xda app yet.
Good luck.
Sent from my GT-I9100 using xda premium
xfile102 said:
Phistachio - I followed your link, but when you get to the following step:
4) Download the necessary files : the Kernel, the Recovery Package and the Bootloader (it's the old one, which you can easily use a USB JIG to reset the counter and remove the yellow triangle when having a custom kernel or OS),
The link provided for the Recover Package is a Hotfile.com link, and the Archive that it downloads is PASSWORD PROTECTED, and there is no mention of a password anywhere on the page you provided, nor on the hotfile.com page.
Any Ideas?
Click to expand...
Click to collapse
No problem I'm glad I can help
The password is samfirmware.com
BTW, to replace the ICS bootloader flash the BL in the thread
Also, I would like to apologize for my first reply (the "Why didn't you search" one)... It was a bit rude...
Phistachio said:
No problem I'm glad I can help
The password is samfirmware.com
BTW, to replace the ICS bootloader flash the BL in the thread
Also, I would like to apologize for my first reply (the "Why didn't you search" one)... It was a bit rude...
Click to expand...
Click to collapse
No Sweat. I'm just trying to follow instructions and get this fixed ASAP. I did flash the bootloader mentioned, with no errors in Odin, but it still loads with the new galaxy S logo animation instead of the old GT-I9100 Logo with the Yellow Exclamation point. AND, I still have no use of the Back and Search buttons, functionality that is removed in the new ICS. What am I doing wrong? I cannot seem to get my phone back to Stock Android.
Related
I'm an admitted noob, but my hope is that somebody here will take pity and be able to shed some light on what I've done and how to fix it.
Here is a general high-level list of what I've done:
1. I attempted to root my phone with SuperOneClick (I think 2.3.3)
2. It hung one Step #7 (as I recall) for about 10 minutes.
3. I disconnected USB cable and reset the phone - it wouldn't boot
4. Started researching, discovered Recovery Mode, selected reset to factory.
5. Reset appeared successful, but then phone went into reboot loop.
6. Tried to access Recovery Mode again, but this time it came to different screen, saying "Deleting cryption meta data".
7. Tried flashing several times with odin and stock PDA's suggested in this forum.
8. Same behavior, so flashed CWM 4.0.0.2 (unfortunately it was for I9100)
9. Flashed new CWM 5.0.2.3
10. When I enter Recovery mode now and I select the wipe data/factory reset option, it just goes to a hat icon with a circular arrow and stays there.
Like I said, I'm new here and have already given up hope on recovering any useful data on my phone. I just want to get it working again so I don't have to buy a new one.
Thanks in advance!
In you item #10, that's a common mistake. The 5.0.2.3 version does not use the power button to select. Use the home softkey to select and the back softkey to go back.
Try to wipe data/factory reset again from this version of CWM Recovery, and then try flashing the one-click downloader return to stock in the "Return to the store or for warranty replacement" thread stickied in general.
Post your results back here and I'll try to keep an eye out to help, but I won't be on the computer every minute.
creepyncrawly said:
In you item #10, that's a common mistake. The 5.0.2.3 version does not use the power button to select. Use the home softkey to select and the back softkey to go back.
Click to expand...
Click to collapse
This guy is right. The power button is the menu/logo button in that version. The newer version changes that mapping though.
You'll likely need to flash the return to stock image. One of them is already prerooted, too!
Sent from my SAMSUNG-SGH-I777 using xda premium
creepyncrawly said:
In you item #10, that's a common mistake. The 5.0.2.3 version does not use the power button to select. Use the home softkey to select and the back softkey to go back.
Try to wipe data/factory reset again from this version of CWM Recovery, and then try flashing the one-click downloader return to stock in the "Return to the store or for warranty replacement" thread stickied in general.
Post your results back here and I'll try to keep an eye out to help, but I won't be on the computer every minute.
Click to expand...
Click to collapse
Thanks so much for your quick reply and help. I followed the instructions you outlined and all went as outlined. Upon final reboot I'm back at Stage 6 in my original post. The original Samsung logo is back (which is a relief), but so is the incessant rebooting and upon trying to enter Recover Mode, I get the Deleting cryption meta data message and then more reboot loop.
Looking forward to your next suggestion(s) and a little sleep.
Oh, by the way, the wipe data/factory reset within CWM appeared to run properly but made no apparent change.
digitalsdc said:
Thanks so much for your quick reply and help. I followed the instructions you outlined and all went as outlined. Upon final reboot I'm back at Stage 6 in my original post. The original Samsung logo is back (which is a relief), but so is the incessant rebooting and upon trying to enter Recover Mode, I get the Deleting cryption meta data message and then more reboot loop.
Looking forward to your next suggestion(s) and a little sleep.
Oh, by the way, the wipe data/factory reset within CWM appeared to run properly but made no apparent change.
Click to expand...
Click to collapse
Tried to answer you this morning, but didn't hit the submit button until a few minutes after 8:00. Let me see if I can do it again.
You did a factory reset and then installed the stock firmware. Now try a factory reset again to see if that will clear the bootloop.
If that does not do it, then you may need to replace another part of the system. We need to know exactly what you flashed for the I9100 while you were trying to fix the original problem (point 8 in your list.) So far, you have flashed everything in the stock UCKH7 firmware except the bootloaders and the param.lfs. You may need to flash param.lfs next to see if that will do it. Is there any chance that what you flashed for the I9100 contained bootloaders?
...........
By the way, having Super OneClick hang on step #6 is a known issue, and the solution is posted in the Super OneClick thread OP as well as in the Library sticky thread in the development section of the I777 forum. If you had been better informed, you could have avoided this problem.
creepyncrawly said:
Tried to answer you this morning, but didn't hit the submit button until a few minutes after 8:00. Let me see if I can do it again.
You did a factory reset and then installed the stock firmware. Now try a factory reset again to see if that will clear the bootloop.
If that does not do it, then you may need to replace another part of the system. We need to know exactly what you flashed for the I9100 while you were trying to fix the original problem (point 8 in your list.) So far, you have flashed everything in the stock UCKH7 firmware except the bootloaders and the param.lfs. You may need to flash param.lfs next to see if that will do it. Is there any chance that what you flashed for the I9100 contained bootloaders?
...........
By the way, having Super OneClick hang on step #6 is a known issue, and the solution is posted in the Super OneClick thread OP as well as in the Library sticky thread in the development section of the I777 forum. If you had been better informed, you could have avoided this problem.
Click to expand...
Click to collapse
First, you're a true gentleman (assuming 'creepyncrawly' to be male) for sticking with me on this issue - Thanks!
To address your first point, I could't do a factory reset after this most recent flash because that dialog doesn't exist any longer. All I get is the "Deleting cryption meta data" message when I try to enter recover mode.
As for the I9100 flash, I used CF-Root-SGS2_XW_XEU_KE7-v4.0-CWM4 first which took me to 4.0.0.2 and then realizing what I'd done, flashed with SGH-I777_ClockworkMod-Recovery_5.0.2.3 which took me to 5.0.2.3, though the I9100 logo still showed during boot.
Thanks again for your help. I will "flash at will" whatever you suggest as at least I feel I'm making progress now.
digitalsdc said:
First, you're a true gentleman (assuming 'creepyncrawly' to be male) for sticking with me on this issue - Thanks!
To address your first point, I could't do a factory reset after this most recent flash because that dialog doesn't exist any longer. All I get is the "Deleting cryption meta data" message when I try to enter recover mode.
As for the I9100 flash, I used CF-Root-SGS2_XW_XEU_KE7-v4.0-CWM4 first which took me to 4.0.0.2 and then realizing what I'd done, flashed with SGH-I777_ClockworkMod-Recovery_5.0.2.3 which took me to 5.0.2.3, though the I9100 logo still showed during boot.
Thanks again for your help. I will "flash at will" whatever you suggest as at least I feel I'm making progress now.
Click to expand...
Click to collapse
The CF-Root-SGS2_XW_XEU_KE7-v4.0-CWM4.tar contains only the kernel zImage, so it doesn't flash any of the wrong bootloaders or param.lfs, so no clue there.
However, the message "deleting cryption meta data" seems to be associated with the lfs, so I would suggest that you try flashing just the UCKH7 param.lfs file using Odin3. Go to the Download Repository where you will find the Odin3 flashable tar of the UCKH7 param.lfs.
creepyncrawly said:
The CF-Root-SGS2_XW_XEU_KE7-v4.0-CWM4.tar contains only the kernel zImage, so it doesn't flash any of the wrong bootloaders or param.lfs, so no clue there.
However, the message "deleting cryption meta data" seems to be associated with the lfs, so I would suggest that you try flashing just the UCKH7 param.lfs file using Odin3. Go to the Download Repository where you will find the Odin3 flashable tar of the UCKH7 param.lfs.
Click to expand...
Click to collapse
I successfully flashed the I777 param.lfs from your download repository. Unfortunately, with the same results. I still get the boot loop and when trying to access recover mode I get "Deleting Cryption Meta Data".
Would you suggest I try flashing the secondary boot loader or .pit files?
digitalsdc said:
I successfully flashed the I777 param.lfs from your download repository. Unfortunately, with the same results. I still get the boot loop and when trying to access recover mode I get "Deleting Cryption Meta Data".
Would you suggest I try flashing the secondary boot loader or .pit files?
Click to expand...
Click to collapse
Well, I had a little extra time tonight so I tried a couple more things after my last post. I went back to the Download Repository and got the secondary boot loader (i777 UCKH7 sbl), flashed with that. No change. Then I got the full set of binaries (I777UCKH7-CL503881-Full), flashed that, and still no change. I think I've tried everything except the .pit and that appears the most risky so I'll await further instruction before trying that.
Am I running out of options at this point?
I had a similiar problem with the deleting meta cache data. I couldn't get it back to working order although I didn't flash pit either. Luckily mine was within 30 days so I gave up and returned for a new one.
Hopefully this deleting meta cache thing can be figured out to see what the cause is. Mine happened from a working rom browsing the web, not from flashing. So I believe it was from aftermarket charger creating some hardware problems to my phone, but not sure what it could have messed up.
If ya can't exchange yours, I hope you figure it out.
Sent from my SAMSUNG-SGH-I777 using XDA App
digitalsdc said:
Well, I had a little extra time tonight so I tried a couple more things after my last post. I went back to the Download Repository and got the secondary boot loader (i777 UCKH7 sbl), flashed with that. No change. Then I got the full set of binaries (I777UCKH7-CL503881-Full), flashed that, and still no change. I think I've tried everything except the .pit and that appears the most risky so I'll await further instruction before trying that.
Am I running out of options at this point?
Click to expand...
Click to collapse
I have always understood that if a phone will boot in any way, or show any sign of life, then it can be recovered. Since you can still get into download mode, you should be able to recover your phone. However, since I am not an Android developer, and I don't really understand the low level workings of the phone, I can't offer any more suggestions myself.
You have flashed the complete I777UCKH7 software package including bootloaders and param.lfs, which also rebuilds the csc, so I don't know what is causing the bootloop.
You need to seek the help of someone more experienced. I have two people on xda in mind who specialize in recovering hard bricked phones, and both have a better understanding of the low level workings of the phone.
Adam Outler is a fantastic hardware level developer who published the unbrickable mod for the Galaxy S series of phones, and is currently moving into the Galaxy S II phones. I have heard that he wants an I777 to work on to try to make the unbrickable mod for our phone. He would probably not charge anything since he is using the phone to learn how to do it, but he might keep the phone for a while.
Connexion2005 of Mobile Tech Videos offers hard brick recovery on the Galaxy S and Galaxy S II series of phones. He also has a very good understanding of the low level functions of the phone.
If it was my phone, I would be contacting these two to see if I could get any guidance about how to recover the phone, probably Adam Outler first. I would try to pm them and I would try to get phone numbers and talk with them in person.
You are not hard bricked. And about the pit, that re-partitions the phone. But I don't have enough experience to know if partitioning could cause the problem you are experiencing.
Good luck moving forward.
Any chance flashing a ROM would do the trick...like Unnamed or SHOstock? Just thinking that maybe he's flashed so many things nothing is playing nice anymore. Just a thought, not necessarily a suggestion. ;-)
Also, how long are you letting it sit in boot loop now? It might be taking a while to rebuild everything...?
Sent from my SAMSUNG-SGH-I777 using XDA App
Nerz said:
I had a similiar problem with the deleting meta cache data. I couldn't get it back to working order although I didn't flash pit either. Luckily mine was within 30 days so I gave up and returned for a new one.
Hopefully this deleting meta cache thing can be figured out to see what the cause is. Mine happened from a working rom browsing the web, not from flashing. So I believe it was from aftermarket charger creating some hardware problems to my phone, but not sure what it could have messed up.
If ya can't exchange yours, I hope you figure it out.
Sent from my SAMSUNG-SGH-I777 using XDA App
Click to expand...
Click to collapse
So, had you rooted and put a custom rom on prior to yours going south, or was it completely stock? What made you think it was related to the aftermarket charger?
Jank4AU said:
Any chance flashing a ROM would do the trick...like Unnamed or SHOstock? Just thinking that maybe he's flashed so many things nothing is playing nice anymore. Just a thought, not necessarily a suggestion. ;-)
Also, how long are you letting it sit in boot loop now? It might be taking a while to rebuild everything...?
Sent from my SAMSUNG-SGH-I777 using XDA App
Click to expand...
Click to collapse
Thanks for your thoughts. I had a similar thought last night and so let it sit through the night rebooting. Sure enough, when I checked it (roughly 8 hours) this morning, it was nice and warm, but still rebooting away.
creepyncrawly said:
I have always understood that if a phone will boot in any way, or show any sign of life, then it can be recovered. Since you can still get into download mode, you should be able to recover your phone. However, since I am not an Android developer, and I don't really understand the low level workings of the phone, I can't offer any more suggestions myself.
You have flashed the complete I777UCKH7 software package including bootloaders and param.lfs, which also rebuilds the csc, so I don't know what is causing the bootloop.
You need to seek the help of someone more experienced. I have two people on xda in mind who specialize in recovering hard bricked phones, and both have a better understanding of the low level workings of the phone.
Adam Outler is a fantastic hardware level developer who published the unbrickable mod for the Galaxy S series of phones, and is currently moving into the Galaxy S II phones. I have heard that he wants an I777 to work on to try to make the unbrickable mod for our phone. He would probably not charge anything since he is using the phone to learn how to do it, but he might keep the phone for a while.
Connexion2005 of Mobile Tech Videos offers hard brick recovery on the Galaxy S and Galaxy S II series of phones. He also has a very good understanding of the low level functions of the phone.
If it was my phone, I would be contacting these two to see if I could get any guidance about how to recover the phone, probably Adam Outler first. I would try to pm them and I would try to get phone numbers and talk with them in person.
You are not hard bricked. And about the pit, that re-partitions the phone. But I don't have enough experience to know if partitioning could cause the problem you are experiencing.
Good luck moving forward.
Click to expand...
Click to collapse
Thanks very much for all your help! I'll try to reach out to these other gentlemen as well.
I've seen other people on these forums with the same problem, but unfortunately, every thread seems to end unresolved. I still hold out hope as I really don't want to eat the cost of the phone and start over.
digitalsdc said:
So, had you rooted and put a custom rom on prior to yours going south, or was it completely stock? What made you think it was related to the aftermarket charger?
Click to expand...
Click to collapse
I figured it was the charger because it was connected when it happened. Was driving home from a Christmas vacation, with maps navigation going, stopped at a rest stop surfing the web. Also on another thread that I read that had a similiar problem, they too thought it was the charger.
And no it was not stock, running unnamed at the time, (though I doubt that is the cause). Like yours I think, I could flash from cwm without success. Wasn't until I flashed stock with stock recovery that I got the deleting meta cache or whatever it is.
Sent from my SAMSUNG-SGH-I777 using XDA App
Any luck so far? I think I'm having the same issues. Although I can flash the stock rom, then a CWM .tar file and get into recovery. But no matter what I do, after boot, the phone starts boot looping.
You can see my thread in the Q&A section.
Shut Guys There is a solution for this !!!! Just make sure you flash back to stock on 2.3.4 (I777UCKH7) and flash the kernel on this post:
http://forum.xda-developers.com/showthread.php?t=1367800
it will take a bit to load but this should do it!!
hardgrid said:
Shut Guys There is a solution for this !!!! Just make sure you flash back to stock on 2.3.4 (I777UCKH7) and flash the kernel on this post:
http://forum.xda-developers.com/showthread.php?t=1367800
it will take a bit to load but this should do it!!
Click to expand...
Click to collapse
THX THX THX THX THX! It worked!
hardgrid said:
Shut Guys There is a solution for this !!!! Just make sure you flash back to stock on 2.3.4 (I777UCKH7) and flash the kernel on this post:
http://forum.xda-developers.com/showthread.php?t=1367800
it will take a bit to load but this should do it!!
Click to expand...
Click to collapse
Hi, did anybody tried this solution??? I'm having the same issue, even tried to contact JTAG unbrick service but these guys told me I'm having a emmc chip failure.
Got the Galaxy S3 on the 3 network in the UK, all was fine & dandy then found out about how the phone was updated & basically 3 sit twiddling their thumbs on it. Went looking for a solution, found a nice simple flash the phone with Odin, use proper Samsung firmware, thought that will do the trick for me.
Unfortunately I did exactly as I was told (didn't go down the root, well, route as there were too many options and I was lost as to wether I was using the right stuff) People swore by the flash to samsung firmware, did that last night, was perfect. Only thing left was the change csc thing, to select BTU but the option wasnt there...was told to download another firmware.......the phone returned with a "unfortunately, the process android.acore has stopped" message, was told to to a reset.......then got "unfortunately, messaging has stopped". Have flashed a few times now to no avail, I can no longer text, is my phone basically broken beyond repair?
Not ruined, but it sounds like you have clobbered some system files. Read up on rooting. Hopefully you can Root and then install a custom recovery like CWM then install a custom ROM.
It would have been better to have made a backup via recovery before you started flashing stuff.
Flash stock ROM and start again
Sent from my GT-I9300 using xda app-developers app
Or even factory reset .
But its a bad flash probably could be a corrupt download or wrong firmware .
jje
seems like u didnt follow the instructions and u could have even bricked your device all that i can say is factory reset or flash a new rom
SilvFlashProd said:
Not ruined, but it sounds like you have clobbered some system files. Read up on rooting. Hopefully you can Root and then install a custom recovery like CWM then install a custom ROM.
It would have been better to have made a backup via recovery before you started flashing stuff.
Click to expand...
Click to collapse
(s)he is having issues just fixing a stock rom misflash and you recommend a custom ROM? Even root was too complicated
I've flashed past phones to death and even still following instructions exactly, they don't always work as they should. Yeah they have cool features and yeah me or you can probably manage to fix any issues they throw up, but they are definitely not for everyone.
Sent from my GT-I9300 using xda app-developers app
bkr32 said:
seems like u didnt follow the instructions and u could have even bricked your device all that i can say is factory reset or flash a new rom
Click to expand...
Click to collapse
Bull****...his problems have nothing to do with a brick. Don't scare him.
i'd defo try a factory, cache and dalvik reset first before flashing again, you'l loose all your data but it may fix the problems you are experiencing.. Boot into recovery mode to do that.
Thanks for all the replies. I have flashed with Odin 3.04 & have found out 3.07 is out...could this be where it all went wrong? I tried following the rooting stuff but found so many variations & in my head (technology challenged when it comes to this) it was all going over my head. I did do the factory reset & reflash with a stock software (the latest I believe) but I don't know if it is a network thing which knackerec me, in CSC I have sales code saying H3G with no options to select BTU. If I post a screenshot of my settings (about device) would that help someone steer me in the right direction as a possible starting point.
My phone appears to be no longer 3 branded, but it should be locked to the 3 network in the uk.
I had the same issue with my Three branded phone. What i did was flash the rom with the PDA button ticked in Odin and then flashed it again with the same file but ticked the CSC icon instead of the PDA and it worked and then let me select BTU from the menu. Give it a try and report back, i'm 99% sure it'll work.
BTW you'll lose the HD voice by flashing it. I still havent found and easy way to get it back working.
bonzai1888 said:
Thanks for all the replies. I have flashed with Odin 3.04 & have found out 3.07 is out...could this be where it all went wrong?
No very unlikely i still use 1.30
I tried following the rooting stuff but found so many variations & in my head
One method works and is easy .
http://forum.xda-developers.com/showthread.php?t=1695238
Stock UK
http://forum.xda-developers.com/showthread.php?t=1646610
jje
Click to expand...
Click to collapse
JJEgan said:
bonzai1888 said:
Thanks for all the replies. I have flashed with Odin 3.04 & have found out 3.07 is out...could this be where it all went wrong?
No very unlikely i still use 1.30
I tried following the rooting stuff but found so many variations & in my head
One method works and is easy .
http://forum.xda-developers.com/showthread.php?t=1695238
Stock UK
http://forum.xda-developers.com/showthread.php?t=1646610
jje
Click to expand...
Click to collapse
The link for the stock you posted is what I used....didn't root as I said, but appeared to work perfectly. Then I lost access to kies & was told I needed to use csc to tick the BTU option & that would work, except I didnt & still don't have that option. Was given another link to apparently the same stock that had "multi csc options" & that when I got the Samsung acore error & I did a factory reset after about 30 minutes of trying to get into the options, then the messaging stopped working & I found out how to do te factory reset using te vol button home power thing. Is there a specific 3 firmware where I can get my phone branded again & take it from there?
Click to expand...
Click to collapse
djstevie said:
I had the same issue with my Three branded phone. What i did was flash the rom with the PDA button ticked in Odin and then flashed it again with the same file but ticked the CSC icon instead of the PDA and it worked and then let me select BTU from the menu. Give it a try and report back, i'm 99% sure it'll work.
BTW you'll lose the HD voice by flashing it. I still havent found and easy way to get it back working.
Click to expand...
Click to collapse
If I try this, what Rom did you use, was it the one in link after you?
What do you want .
Wait for updates via Kies and OTA or join XDA and flash Stock Samsung rom as released ???
Me no Kies and no OTA on my phone
Stock LG9 or leaked Jelly Bean .
jje
JJEgan said:
What do you want .
Wait for updates via Kies and OTA or join XDA and flash Stock Samsung rom as released ???
Me no Kies and no OTA on my phone
Stock LG9 or leaked Jelly Bean .
jje
Click to expand...
Click to collapse
I am happy flashing on release, please understand this is all new. If losing kies is not an issue coz I can just flash then cool. I thought kies was an essential part of the updating. I can use my phone fine just now (using go SMS Pro) but would like it back to fully working phone which would be sweet.
Nothing good is wrong with your phone. It's not even a brick yet. Flash a cwm recovery and then re trying using check rom.
Sent from my GT-I9300 using Tapatalk 2
None of these guys no what there talking about. You've bricked your phone and you won't be able to fix it. Best thing to do is cut your loss and sell it. I'll be generous and give you £50 pounds for it. That's right a fresh £50 note right now, hard cash delivered right to your door step, no questions asked!
Honestly though try flashing the original 3 firmware, it should be in the firmware thread I believe.
P.S You've not bricked your phone, no where near it so don't worry about it.
Sent from my GT-I9300 using xda premium
avocco said:
None of these guys no what there talking about. You've bricked your phone and you won't be able to fix it. Best thing to do is cut your loss and sell it. I'll be generous and give you £50 pounds for it. That's right a fresh £50 note right now, hard cash delivered right to your door step, no questions asked!
Honestly though try flashing the original 3 firmware, it should be in the firmware thread I believe.
P.S You've not bricked your phone, no where near it so don't worry about it.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Thanks...I was giving up again to be honest as once again I was left not knowing what to do. I thought this would be the easiest place to ask but it was ending up in riddles, which is why I gave up on rooting it in the first place.
bonzai1888 said:
Thanks...I was giving up again to be honest as once again I was left not knowing what to do. I thought this would be the easiest place to ask but it was ending up in riddles, which is why I gave up on rooting it in the first place.
Click to expand...
Click to collapse
I'm on 3 UK same happened to me when I unbranded. Don't panic your phone is fine. Turn off phone then hold power + home + volume up. Let go when you see the Android man. Wipe factory reset and dalvik cache you will lose everything. Then reboot. Don't bother letting it boot back up, just hold power + home + volume down. Then flash unbranded rom via odin. Once done and booted type *#272*yourimei# and you should now have option of btu.
Sent from my GT-I9300 using xda premium
bonzai1888 said:
If I try this, what Rom did you use, was it the one in link after you?
Click to expand...
Click to collapse
Was the latest UK unbranded rom in the first page.
So, today I updated my phone to ICS and rooted my phone and just like a little kid i started playing with things and long story short I'm pretty sure I bricked it. I think what happened just before I think it bricked is that I was downloading and installing a ROM from ROM Manager. It went through the whole start up process(asking for gmail for syncing and all that nonsense) and when i tried to download another app from the google store i got a "error with purchasing" or something like that so i restored all the info and stuff i had on ROM manager and titanium back up and tried it again. no luck. I tried going for factory reset but it didn't work(all three ways). So i panicked and went to superuser and clicked the unroot choice. Really stupid choice since now i can't use any of the apps to get into bootload. Now I can't get to recovery, bootload, or any other of those things even with hardware.
So in summary here are the symptoms:
1. can't get into any other modes (recovery, bootload, etc.)
2. Get the error "Error processing purchase.[DF-BPA-13]" when trying to download something off google play.
3. Charges extremely Slow.
4. Phone works normally. goes through normal boot. I can text, browse, do all standard functions.
5. When turning off the phone it gets hung up at goodbye.
6. Can't perform hard resets.
More information:
Model Number: SGH-T989
Android Version: 4.03
Please Help! I'm begging you! and if you need more information just let me know. and one thought I would have in fixing it is using a USB jig. But i wouldn't know what to do once I got back into the other modes.
you can search how to fix it here on xda, but maybe this will give you a lead http://forum.xda-developers.com/showthread.php?t=1805474
hope you get it fixed!
Right well there is 2 things you can do:
1) use a USB jig and get into download mode, and then flash a stock ROM
2) Do an adb restart into recovery using android SDK
Let me know if it work?
Sent from my GT-I9100 using xda premium
This is a forum for the international version, i9100. Your device T989 is a completely different device and has its own forum.
http://forum.xda-developers.com/forumdisplay.php?f=1329
Sent from my Galaxy S2 GT i9100
I don't think the phone is "hard bricked"
what version of ICS was you on?
UrbanDesigns said:
I don't think the phone is "hard bricked"
what version of ICS was you on?
Click to expand...
Click to collapse
I'm kind of a noob, sorry. But I think I'm on 4.0.3 . Or do you mean like t989uvle1
Try to reflash an stock firmware again ？
Infinite96 said:
Try to reflash an stock firmware again ？
Click to expand...
Click to collapse
Where would I get the stock firmware and how would I go about it . my Odin still works.
Infinite96 said:
Try to reflash an stock firmware again ？
Click to expand...
Click to collapse
i reflashed a stock recovery and it works just fine now. Thanks a lot!
Hi there i have a SGH-i717 with AT&T 2.3.4 Stock installed..I did have Cyanogen 10.1 and Avatar all installed in the last 72hrs..I have wiped all that and did a return to the stock AT&T thinking that my HOME keys would return..NO LUCK..The problems started about 4 days ago when the phone started turning itself off automatically..I changed custom ROM's etc to try and fix the problem..then i read to use Kies to try and do a Firmware Upgrade and Initialization to go back to the start when i first got the phone..But now Kies will NOT recognise the phone..I have re-installed drives, Kies to no avail..Any tips ?
Also someone suggested to flash this kernel h0tcakez-JB-Kernel-v2.3.5-ALT but when i tried through system recovery is gives a falied error..
I have nothing on the phone i need to worry about loosing...Cheers
kakadu44 said:
Hi there i have a SGH-i717 with AT&T 2.3.4 Stock installed..I did have Cyanogen 10.1 and Avatar all installed in the last 72hrs..I have wiped all that and did a return to the stock AT&T thinking that my HOME keys would return..NO LUCK..The problems started about 4 days ago when the phone started turning itself off automatically..I changed custom ROM's etc to try and fix the problem..then i read to use Kies to try and do a Firmware Upgrade and Initialization to go back to the start when i first got the phone..But now Kies will NOT recognise the phone..I have re-installed drives, Kies to no avail..Any tips ?
Also someone suggested to flash this kernel h0tcakez-JB-Kernel-v2.3.5-ALT but when i tried through system recovery is gives a falied error..
I have nothing on the phone i need to worry about loosing...Cheers
Click to expand...
Click to collapse
If you are on stock 2.3.4 and tried to flash that kernel .. that is why it failed .. it would be the wrong kernel for that rom. Did you flash a stock rom in recovery? If so then I would suggest using oden to return to stock . then see what you end up with.
SGH-i717 Home Keys not working
Bubbajoe40356 said:
If you are on stock 2.3.4 and tried to flash that kernel .. that is why it failed .. it would be the wrong kernel for that rom. Did you flash a stock rom in recovery? If so then I would suggest using oden to return to stock . then see what you end up with.
Click to expand...
Click to collapse
Thanx for you reply..I did however flash stock 2.3.4 from oden..I deleted everything in recovery then went to oden and flashed the stock rom..Should i unroot/unbrick flash from oden?
That article about returning to original settings in Kies seems to make sense except for the fact that i cannot get Kies to recognise the phone...
Are we talking about Software ou Hardare issue in your opinion?
Cheers
Could be a hardware issue. Try this ... Put the phone into download mode then connect to the pc. Use the cable that came with the phone. Also use a port on the back of the pc ..not a hub. Then open kies and do the emergency firmware update.
Also ... When you used Odin to go to stock ..you installed the 3e recovery ..that's why it failed to flash. Which is a good thing. That kennel would have boot looped you.
Sent from my Big Ass Outlaw Phone
SGH-i717 Home Keys not working
Bubbajoe40356 said:
Could be a hardware issue. Try this ... Put the phone into download mode then connect to the pc. Use the cable that came with the phone. Also use a port on the back of the pc ..not a hub. Then open kies and do the emergency firmware update.
Also ... When you used Odin to go to stock ..you installed the 3e recovery ..that's why it failed to flash. Which is a good thing. That kennel would have boot looped you.
Sent from my Big Ass Outlaw Phone
Click to expand...
Click to collapse
Okay i installed from ODIN Stock 2.3.4.....I dont have a port on the back of the PC to use as i only have a Laptop...Kies will not recognise the phone..Even when the phone is at Stock it takes soooo long to boot up..approx 2 mins..can i not run the emergency firmware update from ODEN? If so where can i find the software please..
Also even when i go into recovery mode it shows error signs..it wont let me wipe cache or wipe data/factory reset..
cheers
kakadu44 said:
Okay i installed from ODIN Stock 2.3.4.....I dont have a port on the back of the PC to use as i only have a Laptop...Kies will not recognise the phone..Even when the phone is at Stock it takes soooo long to boot up..approx 2 mins..can i not run the emergency firmware update from ODEN? If so where can i find the software please..
Also even when i go into recovery mode it shows error signs..it wont let me wipe cache or wipe data/factory reset..
cheers
Click to expand...
Click to collapse
The lap top is fine. Emergency firmware is through kies and not Odin. You need download mode ... Not recovery.
Sent from my Big Ass Outlaw Phone
Bubbajoe40356 said:
The lap top is fine. Emergency firmware is through kies and not Odin. You need download mode ... Not recovery.
Sent from my Big Ass Outlaw Phone
Click to expand...
Click to collapse
It will not recognise the phone in KIES!!!!! i have uninstalled USB drivers and re-installed and still it will not recognise the phone..Is there USB debugging in Stock 2.3.6? If so where do i find it in Settings pls? thanx
kakadu44 said:
It will not recognise the phone in KIES!!!!! i have uninstalled USB drivers and re-installed and still it will not recognise the phone..Is there USB debugging in Stock 2.3.6? If so where do i find it in Settings pls? thanx
Click to expand...
Click to collapse
Please can you advise me what is the best way to WIPE my phone of ALL my info to start over again, just like a complete wipe on my laptop..cheers
Have you tried here, briefmobile. com /exclusive-ucld3-ics-leak-for-the-att-galaxy-note
sp73smith said:
Have you tried here, briefmobile. com /exclusive-ucld3-ics-leak-for-the-att-galaxy-note
Click to expand...
Click to collapse
Hi there thanx for your answer..I have not tried at that site..this program will do what? COMPLETELY wipe my phone??cheers
It will, it completely erases everything. Replaces recovery and losses root. Very simple to use, I use it every other month.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
SGH-i717 HOME keys are not working...
sp73smith said:
It will, it completely erases everything. Replaces recovery and losses root. Very simple to use, I use it every other month.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
Click to expand...
Click to collapse
Yep i used it..very good..But my original and main problem..Continues..NONE of my HOME keys are working..I fear that it is a Hardware issue with the SGH-i717..I guess i have to take it to Samsung for repair..Until someone else can give me a solution..I have tried everything and nothing has worked..No HOME keys..Cheers
Definitely not a hardware issue, there where some changes made IIRC in the kernel driver files, once flashed they prevented the homerow buttons from working normally, the only way I ever found to make them work right was to flash the Flappjaxxx alternate kernel series, let it boot, then return completely to stock!
If you dig around, FJ's alt kernel's are around here somewhere!
SGH-i717 HOME keys are not working...
Hammerfest said:
Definitely not a hardware issue, there where some changes made IIRC in the kernel driver files, once flashed they prevented the homerow buttons from working normally, the only way I ever found to make them work right was to flash the Flappjaxxx alternate kernel series, let it boot, then return completely to stock!
If you dig around, FJ's alt kernel's are around here somewhere!
Click to expand...
Click to collapse
Good morning, well i believe i have finally arrived at a possible solution..I have searched hi and low for these Flappjaxxx alternate kernel ..I came up with a daunting array of alternatives for the complete amatuer as i am..I appreciate that your time is precious but i do need some general direction what exactly i am searching for..I have found this one but to be quite honest i am not sure if i need this whole ROM or just the Flappjaxxx alternate kernel'a..
http://db.communityrelease.com/developer_display.asp?DeveloperID=11381
https://github.com/flappjaxxx/kernel_samsung_sghi717
Also when i do eventually obtain the Kernel that i am looking for can i use ODIN to flash it? I installed this ROM which i beleive to be stock already..You wrote that i need to return COMPLETELY to stock..What is that 2.3.6???
http://briefmobile.com/exclusive-ucld3-ics-leak-for-the-att-galaxy-note
I appreciate any further input you may be able to supple..regards kakadu44
kakadu44 said:
Good morning, well i believe i have finally arrived at a possible solution..I have searched hi and low for these Flappjaxxx alternate kernel ..I came up with a daunting array of alternatives for the complete amatuer as i am..I appreciate that your time is precious but i do need some general direction what exactly i am searching for..I have found this one but to be quite honest i am not sure if i need this whole ROM or just the Flappjaxxx alternate kernel'a..
http://db.communityrelease.com/developer_display.asp?DeveloperID=11381
https://github.com/flappjaxxx/kernel_samsung_sghi717
Also when i do eventually obtain the Kernel that i am looking for can i use ODIN to flash it? I installed this ROM which i beleive to be stock already..You wrote that i need to return COMPLETELY to stock..What is that 2.3.6???
http://briefmobile.com/exclusive-ucld3-ics-leak-for-the-att-galaxy-note
I appreciate any further input you may be able to supple..regards kakadu44
Click to expand...
Click to collapse
My work schedule is absolute hell, and due to people flaking at work I have been called in 2x to cover on my only days off...
Needless to say, im about to pass out, so im going to make this useless post...
Either I, or someone else can link you to a FJ rom, and the FJ alternate kernel that match, what you will need to do prior is make sure you have EVERYTHING you want/need, backed up to GMail (in the case of Phone logs, SMS and MMS with the Backup to GMail app, yes, im whoring this fantastic app out) AND to your computer, NO not your SD card, but your computer!
Make sure you have the latest recovery (TWRP 2.5.0.0 is what I have, but whatever TWRP is latest will do), wipe everything, then install the rom, boot, wait 10min, reboot into recovery, flash the alt kernel, boot, wait 10min, then test the home/back/menu/search key row, they should work, at this point, you CAN go back to the 2.x.x rom you where running, but if you have an i717, I have had nothing but love for the Stock rom update on AT&T once I performed a complete ODIN to it (flashing the ones here on the forum's resulted in random reboots here and there, and while less then ever before, still annoying, after an ODIN however, havent had a random reboot yet!).
There are issues with the GNote i717 JB release, many posted here, and quite a few here:
http://forums.att.com/t5/Android-Di...getting-Jelly-Bean-update/td-p/3421041/page/5
Including my own rant towards the bottom...
Needless to say, ill try and get on tomorrow to get the right links you will need, or some other kind sirs can...... either way, I have fallen asleep in the middle of writing this, so if something doesnt make sense... well, sleep writing was never my skill of choice
SGH-i717 HOME keys are not working...
Hammerfest said:
My work schedule is absolute hell, and due to people flaking at work I have been called in 2x to cover on my only days off...
Needless to say, im about to pass out, so im going to make this useless post...
Either I, or someone else can link you to a FJ rom, and the FJ alternate kernel that match, what you will need to do prior is make sure you have EVERYTHING you want/need, backed up to GMail (in the case of Phone logs, SMS and MMS with the Backup to GMail app, yes, im whoring this fantastic app out) AND to your computer, NO not your SD card, but your computer!
Make sure you have the latest recovery (TWRP 2.5.0.0 is what I have, but whatever TWRP is latest will do), wipe everything, then install the rom, boot, wait 10min, reboot into recovery, flash the alt kernel, boot, wait 10min, then test the home/back/menu/search key row, they should work, at this point, you CAN go back to the 2.x.x rom you where running, but if you have an i717, I have had nothing but love for the Stock rom update on AT&T once I performed a complete ODIN to it (flashing the ones here on the forum's resulted in random reboots here and there, and while less then ever before, still annoying, after an ODIN however, havent had a random reboot yet!).
There are issues with the GNote i717 JB release, many posted here, and quite a few here:
http://forums.att.com/t5/Android-Di...getting-Jelly-Bean-update/td-p/3421041/page/5
Including my own rant towards the bottom...
Needless to say, ill try and get on tomorrow to get the right links you will need, or some other kind sirs can...... either way, I have fallen asleep in the middle of writing this, so if something doesnt make sense... well, sleep writing was never my skill of choice
Click to expand...
Click to collapse
READY AND WAITING..THANX
Okay thank you for reply..I am ready to go with the install/flash...
When you get time to direct me to the correct ROM and Kernel i would be much obliged..In the meantime enjoy your rest..Cheers Mick
Hi I tried to root my phone using this method ( http://forum.xda-developers.com/showthread.php?t=1504218 ) and it left my phone stuck on the reboot. I then tried to flash the stock kernel via odin, and when that didn't work I flashed cwm via odin and then a rogers kernel through cwm and it is still stuck on the rogers logo.......?
could someone help me......?
AirForce 1 said:
Hi I tried to root my phone using this method ( http://forum.xda-developers.com/showthread.php?t=1504218 ) and it left my phone stuck on the reboot. I then tried to flash the stock kernel via odin, and when that didn't work I flashed cwm via odin and then a rogers kernel through cwm and it is still stuck on the rogers logo.......?
could someone help me......?
Click to expand...
Click to collapse
I see your post count and realize you cannot post in the development section yet. that should not however stop you from reading. maybe you have but you may not have read the whole thread. i know that may seem like a daunting task, it is for me. so what I o is go to the most recent post or last page and start reading backwards. that way I get the most up to date information even on an older thread as you are referring to.
if you did that you would have seen a post from AGOATTAMER.
http://rootgalaxynote.com/galaxy-note-i717-roms/how-to-root-att-galaxy-note-sgh-i717-icsgingerbreadeasiest-method/
this is also the method I used. believe me, if I can pull it off, anybody can.
more tips..............
make sure you have all the files you need
rehearse the process
I know it sounds crazy, but these phones aint cheap and if you mess it up, can be pretty screwed.
so what is more valuable???? your phone or acting crazy and talking to yourself for a few minutes.
if you can still get download mode, your good, no brick
good luck
You flashed an older incompatible kernel with a newer ROM, but I guess you know that now. Flash the stock ROM found here using odin.
http://www.hotfile.com/dl/213010140/75bf7e2/I717RUXMD1_I717RRWCMD1_RWC.zip.html
Go into recovery after install and do a factory reset. Then start over. Many have used the link that captemo has mentioned. There are newer versions of recovery than the one listed on that site but it will get you rooted. Look at this thread also. Since you are installing the stock ROM via odin you will not have to deal with the script mentioned here.
http://forum.xda-developers.com/showthread.php?t=2485336
Just flash twrp with Odin, don't reboot into android, not directly into recovery after the flash finishes...
In recovery wipe data/factory reset.
When you go to boot it'll see you're not rooted and ask if you want to.
The easiest method to root.
Edit: note to self
Self,
check links before posting to avoid repeating yourself
studacris said:
Edit: note to self
Self,
check links before posting to avoid repeating yourself
Click to expand...
Click to collapse
Good advice is always worth repeating.
Sent from my Big Ass Outlaw Phone.