Related
I started leaving my Gtablet on for the weekend. Just got the Tablet ( I have one already) and issue I have is after maybe a day and a half of being left on BUT with the screen off I cant turn it on. I hit the power button and nothing. I have to hold the power button for ever to get it to re start. My other tablet I can leave on ( Screen off) for a week and no issues. Its like it goes into sleep mode after a day or so ( All day its fine , its if I dont touch it for more then a day)
Other then that no isses on this tablet I just got. any clue what might cause this. I like to leave it on from Friday to Sunday night as I use it alot. but now I am afraid it will at some point not turn on. I have no problem starting it normal if its turned off every day.
Thanks
Had to get my one day old Nokia 800 replaced today.
Got everything setup last night and decided to power it off just to give it a restart. The phone would refuse to power back on. No amount of button pushing/reconnecting to the power would make it start up again. No power, nothing..dead.
I managed to get it to restart after performing the three button reset. No problem I thought maybe just a one off. Turned the phone off and put it on charge overnight and this morning the same problem returned.. Could not power on. This time the reset would not work at all, no matter how many times I tried.
Carphone warehouse swapped it over in store today for another handset. Hopefully I'll have more luck with the replacement.
Edit: already seen someone else mention a similar problem on here. Hope there's not a bigger issue.
How do you perform the three button reset? My phone randomly decided to turn off whilst I was driving and now it wont turn back on
Yes I've been in that spot as well. For five minutes the phone wouldn't respond to any power button press. Long, short, whatever. I was already starting to slide into panic mode when it suddenly came back alive on another short press.
It's not the only hardware problem I've encountered, I also have problems with touchscreen and buttons and a loose part inside the device.
I found a couple posts about this but people seemed to just return or RMA it. Thought maybe my experience might help others and was curious if anyone else has this problem.
A few times I have picked up the Prime and hit the power button and the display would not come on. If I plugged it in I would see the green light on the power button come on and go off when unplugged. It appeared to still be attached to the WIFI. If I held the button down it would buzz, but nothing else.
I found out that if I held the button down, waited for it to buzz then continued to hold it down for another 30 secs or so (seems like it takes forever) the Prime would then reboot and I would get the Eee Pad boot screen.
I have been storing my Prime in the box to keep it clear of kids and cats until I get a case. My wife ended up picking up this cheap case from Walmart which used rubber bands around the corners, and this triggered the problem by holding down the volume up button. I have not been able to reliably reproduce it, but it seems like holding down the volume button (or combo of power and volume button) puts the device in some diagnostic mode or something that shuts off the screen.
The natural tendency to release the power button immediately after the buzz while trying to reset made the device seem like it was broken. Luckily I figured out how to start it back up so I did not return it or RMA; however I wonder how many others experienced this problem.
This appears to be a software problem and not a hardware issue. I have not had this happen since I started being cautious about the volume buttons, but have not tried to reproduce on the last firmware update.
I have had no other issues with the Prime. It runs great, WIFI works for me and I could care less about the GPS issue. However, this display thing has scared me a handful of times until I figure out how to reset it.
Anyone else have this kind of issue? I was going to wait for ICS and then see if I could reproduce it before calling ASUS, but it has not been crippling especially once I figured out that when all else failed just hold down the power button until the screen came back on.
I've had this problem as well, three or four times so far. Actually, it happened to me on the first full day I had mine, and was really freaking me out. I've been using the pinhole reboot button to get it working, but it sounds like you were more patient with the power button than I was.
I can't replicate it either, exactly, but I've noticed that it's only happened after extended periods (6+ hours) of inactivity without charging. I also looked at my battery usage last night, and saw that my device constantly is awake; maybe somethint's happening when it tries to sleep?
Anyway, I feel the same way you do - I'm waiting for it to happen on 4.0(.3?) before I really worry.
I've had this happen twice. held down the power button to reboot. I can't reproduce it either, but I don't have any problem with the device sleeping. I'm at 50 hours of uptime now (15 on current charge) and have not run into it. Mildly glad to see its not just me though.
TF201 | XDA Premium
Only once tonight. Scared me until I saw the boot screen. Interesting since it has been rock solid until this. No other problems just didn't turn on. Glad to be back working.
Sent from my Transformer Prime TF201 using Tapatalk
never had that issue...have used it quite a lot in many different situations
This morning it didn't wake up. I got it to turn on by holding get down the power and volume down button. Hopefully it doesn't happen again.
Sent from my Transformer Prime TF201 using Tapatalk
happened to me tonight freaked me out for a while - had to use the reset pin hole
I've had the same exact problem andthe funny thing is I also have a case from Walmart with the rubber bands. Is yours the case logic? Since reading this post, I've removed the upper left band. I wish my case would ship already!
guys if you're familiar with transformer 1 and hacking\custom ROM tegra devices power + vol up = apx mode kind of download mode blank screen, nothing wrong with the device just working like it should. now just a blank screen with sound when u plug in could be defective screen has happened to me
Awesome to know this is expected behavior.
I didn't have the original transformer, and googling has just led me to people who can/can't get into the mode, so I'll ask here: what exactly is apx mode? I get what it's for, sort of, but what is it?
also happened to me while it was in a case. maybe the power button was pressed too long or something...
this happened to me yesterday, except the screen is still off....tried everything mentioned and it wouldnt turn back on, its fully charged...i get no buuz sound or anything...
LOL, I was just searching for a thread like this.
Mine has been working flawless for the last 4 days. This morning, would not turn on. I tried every combo and button push I could think of.
No LED charging lights, nada.
I finally reverted to the paper clip in the reset hole. Booted right up.
Don't know what the issue is.
reset button wont even work for me...
Yes It happend to me yesterday twice... i think if we leave it for an extended period without out charge , the screen is getting locked somehow... both the times i have held the power button till the buzz.. then it rebooted....
Same behavior here, was fully charged in the Morning, and plugged in, when i got home Both LED's (Dock and Tab) were green but the Screen won't turn on, pressing the Power button for 10sec rebooted the device, maybe some kind of power saving feature... hopefully it will be fixed with ICS
Okay, rockstatus90's problem seems different, but the rest of us, pceasar explained that we're likely entering APX mode, right? It's designed behavior? Now I just want to know what APX mode is, and if there's an easier way to exit than rebooting.
Happened twice for me so far.
chinly43 said:
Okay, rockstatus90's problem seems different, but the rest of us, pceasar explained that we're likely entering APX mode, right? It's designed behavior? Now I just want to know what APX mode is, and if there's an easier way to exit than rebooting.
Click to expand...
Click to collapse
Yes this is normal. Although most other Android devices seemed to give some sort of on screen message.
It is mentioned here as a process of rooting the original TF:
http://eeepadhacks.net/transformer-hacks/how-to-root-your-eeepad-transformer/
Basically, this is a mode that outputs to your PC and is supposed to blank your screen. You are supposed to reboot afterwards, so there is no other way out.
I have not had the problem since being sensitive about pushing volume+ and power at the same time.
rockstatus90 said:
reset button wont even work for me...
Click to expand...
Click to collapse
Unfortunately it looks like return or rma is your solution. I would try to call Asus and see if they can troubleshoot it. Best case they can reset it for; worse case its dead.
Really wish you could pull the battery. Thats the sure fire reboot.
So all seemed to be fine and dandy after the update, but I went to check something on my tablet and it wouldn't wake up. Pressing the power button, or even holding it didn't do anything; the screen was black. I held volume up and power and it vibrated, then I held it again and it vibrated again. The third time I did this, it finally booted up again.
Dunno what this means.
EDIT: Just happened again, although now I can't seem to get the thing back on. The screen is just off and vol. up + power only makes the thing vibrate after a few seconds. I simply left the prime on the lock screen and came back and it was stuck again.
Prime BT tether lockups
XHolyPuffX said:
So all seemed to be fine and dandy after the update, but I went to check something on my tablet and it wouldn't wake up. Pressing the power button, or even holding it didn't do anything; the screen was black. I held volume up and power and it vibrated, then I held it again and it vibrated again. The third time I did this, it finally booted up again.
Dunno what this means.
Click to expand...
Click to collapse
Mine does the exact same thing when I tether it to my Sensation with BT.
I'm still on 2.11.1 though
UPDATE
I just manually updated my pad to .13 this morning. It did NOT alleviate my problem but it didn't make it any worse. Unlike many other user who report the lockups when sleep now, mine still only occurs when I tether BT and it goes to sleep. On the upside, I've tested my wifi and do confirm an improvement ~20% increase in signal strength and quality.
According to dd-wrt on my router signal increased from about ~49% to 63%
and Wifi analyzer signal strength ~77-68dB to ~54-47dB. I have not tested GPS.
Apparently the build variance between pads are reflected by the variance in the effects of the update
nattylite said:
Mine does the exact same thing when I tether it to my Sensation with BT.
I'm still on 2.11.1 though
Click to expand...
Click to collapse
How do you get it back on? I can't seem to power it up now.
EDIT: Nevermind, I just held power and it turned back on after about 5-7 seconds. I think it might be a "Wifi off during sleep" issue..but idk.
XHolyPuffX said:
So all seemed to be fine and dandy after the update, but I went to check something on my tablet and it wouldn't wake up. Pressing the power button, or even holding it didn't do anything; the screen was black. I held volume up and power and it vibrated, then I held it again and it vibrated again. The third time I did this, it finally booted up again.
Dunno what this means.
EDIT: Just happened again, although now I can't seem to get the thing back on. The screen is just off and vol. up + power only makes the thing vibrate after a few seconds. I simply left the prime on the lock screen and came back and it was stuck again.
Click to expand...
Click to collapse
same thing is happening to me after the update. My prime never used to do that but something in the update screwed with it. is there anyway we can revert back?
Doubt this is an update issue as I haven't seen it yet or most others. Or they all would be posting about it. That is strange though. You all didn't root n go messing around with stuff did you? Lol. If anything I'd try a fresh reboot. Maybe even clear out all the caches. Something else is seeming to cause this. By any chance did you install chrome beta? Some users reporting strange things since installing it. I don't think its the app but it is strange though or coincidence.
demandarin said:
Doubt this is an update issue as I haven't seen it yet or most others. Or they all would be posting about it. That is strange though. You all didn't root n go messing around with stuff did you? Lol. If anything I'd try a fresh reboot. Maybe even clear out all the caches. Something else is seeming to cause this. By any chance did you install chrome beta? Some users reporting strange things since installing it. I don't think its the app but it is strange though or coincidence.
Click to expand...
Click to collapse
no I didn't root. I may factory reset if it keeps doing it and see if that works. I got a decent working prime and it would suck if this update is giving me problems. yes I did install chrome beta but this issue happened before I even installed it so that can't be it.
Ok, this has to do something with the update.
My perfectly fine from before prime wouldn't unlock. I couldn't get it to respond. (I thought it was dead..) I tried to unlock and pressed volume, did nothing.
I just read this thread and tried holding the power button and it vibrated and booted after the hold...
Asus needs to stop the patch roll out untill this is fixed...
Same problem for me. And after a short sleep, it wakes up, but there is a delay of about one half second that didn't used to be there.
-gary
After that one sleep, it has not yet repeated since last night for me
not only did mine do the same thing but it also killed my battery life while my Prime was sleeping... epic fail asus its time to return for a refund and never look back.
Maybe try reverting back and see if the problem goes away.
This hard-to-wake-up issue happened to me once after the update, but my Prime did finally wake up. Have not had the issue since. There was a lag in the wake up yesterday also, as others have mentioned, but even that seems to be gone now (or I'm just used to it).
Possible fixes for this situation:
1) Hard reset (stick an open small paper clip into the little hole just below the microSD) -- I'm sure most of you have tried this already...
And, if that doesn't work:
2) Hard reset, then reapply the .13 firmware update manually right after (assuming that is possible)
My tendency is to always do a hard reset just before any firmware updates -- makes me feel a little more confident. I was lazy and did not do that yesterday, but it won't happen again.
enough with this crap
Dude, you really gotta stop trolling, this is the third thread you are spewing this crap in in the last three I read.. You obviously are not returning it, you just like to *****.
PrimeTimeBro said:
not only did mine do the same thing but it also killed my battery life while my Prime was sleeping... epic fail asus its time to return for a refund and never look back.
Click to expand...
Click to collapse
unsure if this is the right thread, but mine's been acting up since the update as well. when i'm actively using it and turn off the screen, it boots up as quick as before to the unlock screen. however, after letting it sit for a few hours, it seems to have shut off where i'll have to hold the power button on for a few seconds (after 2 or 3 tries) to get it to boot up again as if i reset the tab.
Having the same issues with mine as well. I have installed Chrome Beta, but had it running for a few days pre-update without issue.
I almost always keep mine in the dock, but haven't had a chance to determine if it only happens in the dock or not.
i have seen this occur in the past ..before the update.. i thought the battery was dead but plugging in the charger didnt do much.. held the power+vol up 3 times finally woke up .. and said 36% battery left... i m on the verge of returning this after 2 weeks of use.. just cant get over these silly silly issues
Mine just did the same thing. I'm on the newest update. Had to hold power button 10+ seconds for it to come back.
Sent from my Transformer Prime TF201 using Tapatalk
Mine died over night with a charge of 36% in balanced mode. Had to hold the button down for 10 seconds to get it to turn on today after it was plugged in the charger for 20 minutes. Now when i wake it out of sleep there is a .5/1.5 second delay for the screen to come on.
Same issue
Had absolutely no issues with my tablet prior to this update - no random reboots, but now if it's off for a minute or more, I have to hold power in for 7-12 seconds to boot up the system.
Hey, just a thought.
Maybe also include the first few of your tablet's serial number to see if the problem is consistent with some batch(es) and not others? May help others that's going to update...
I have no idea what caused this, but I can briefly explain the scenario..
After the .21 update, I found my Prime to be a little lag-gy (you know like when your desktop is on for quite a long time, you try to reboot), so I wanted to turn it off, then turn it on again. To my horror after I turned it off, I could not turn it on again. All I can is have this vibration that's supposed to occur at 3 seconds normally, at 12 seconds of holding down the power button.
After doing some research , others that have similar issues of unable to boot tried holding down the power button for 30 seconds.. 60 seconds.. and multiple times.. I've tried it, but nothing worked.
I tried the cold boot, holding VOL Down plus power button as well. No luck.
Lastly, tried the soft reset button. Tried it holding down with power button and pressing it separately. Still no luck.
I tried it with and without dock. Everything almost the same except when I
'close' the tablet with the dock.. holding the power button does not do anything, but when i 'opened' it, 3 seconds I will get the vibration, but nothing will be shown on the screen. Totally blank.
Anyone can help? I'm going to send for RMA at worse scenerio but I need help asap cause I need to use it later in the day. :/
EDIT: Oops forgot to include something else.
That was 3 days ago, I managed to get it working 2 nights ago, but after I went to sleep, and woke up. Heck, its off again. I have no idea how I got it working. All i know was, I brought it out, didn't use it, about after 8 hours I reach home, I sat on my chair thinking of sending it for repair and tried my last attempt to on it, it loaded perfectly. Then... this happened...
After I connected my tablet to the computer and try to turn it on, Windows detect APX. But the driver installation. Wonder if this information would be useful.
Again new information don't know whether this is useful or not, my volume up button was faulty about a week ago. Sometimes my volume just automatically goes up on its own, probably the button is spoilt that its permanently or most of the time held down. And after some Google-ing, volume up and power on apparently causes the tablet to go in this APX mode..