Related
Hey guys,i got an x10i, wit 1.6 firmware and wanted to update to 2.1. I saw the option of update in the phone menu,so i tried it and it actually found update and downloaded it.but after the restart i got exclamation mark and no boot.the phone has no warranty so can i fix it my self?
Sent from my GT-I9000 using XDA App
Reconnect the phone to SEUS and run " repair " option, should reflash the phone.
Try taking the battery out first and let the phone set a bit, reinstall batt and see if she boots up, remember, 1st boot takes a few minutes after you flash new firm ware.....
Best regards,
Chris
I took the battery out long time ago.havent tried yet.One more wuestion.is there a recovery built in?or a factory reset?and how to fo this if i neef to.
Thanks a lot
Sent from my GT-I9000 using XDA App
Depends on where and how you upgraded to new firmware, if it was thru seus / pc companion, then you just have factory firmware, no recovery.
If you used the flash tool from XDA and picked the firmware on that page, and installed xrecovery, then yes you have it. Clear as mud, sorry.
IF you have to run the seus pc companion to " repair " the phone, you will have only factory sony firmware. You can search for the firm ware # and flash tool , instructions, root methods, xrecovery, all are on xda!
Hope this helps,
Chris
As i said i used the phone menu for this update.No seus,no pc companion,just update through the phone menu and wireless network.
i downloaded seus and and it sais:
Failed checking application versions, please reinstall the application and make sure you have the latest version
what is this now?
Any link for the right one?
Thanks again
try the repair option on seus, comes up when u first connect the phone to pc companion,
Sent from my X10 CM7 TripNRaVeR using the XDA mobile application powered by Tapatalk
my x10i v2.3.3 batt was running low at 8%... so i turn it off from my work place... when i reach home and turn my phone on, my phone only vibrate abit and nothing was happen... so i tot my phone battery is flat so i when to charge it... but when i charge the phone nothing happens too.. i try take out the batt and put it back afew times but still not working... so i tot is my software facing problem and i use PCC and SEUS to repair... but it say can't install update try again.. i do it around 3 to 4 times... but still the same.. now my phone when i press on it blink green led once and nothing happen... but when i plug in my charger, the led turn green but in black screen... so can any1 help me fix tis.. thanks...
Hey, 'm facing the same issue
Recently i upgraded my Xperia to "ThGo2 v16.0" from custom rom..
After some time the rom got unstable and restarted the phone, however it wouldn't boot up. Now i have completely black screen, all the time, with few red blinks
(I have tried all the solutions here:
1. SEUS : Says ur phone is already update and show Xperia arc in backgroud. No update available
2. PC companion: Tried all the tricks to start w/o connecting n all still the phone is not detected.
3. Flashtool, tried flashing it with 0.6.8 and 0.2.9.1
4. I have also used other tools like superclick, root / unroot and S1 tool (no of them worked)
Now, nothing is working with few red blinks and gree light..
Please help, my phone is converted into a black paper weight now....
Use pc companion. Or flashtool
Sent from my X10 using xda premium
Nopes
I have tried all the method, right from SEUS, PC Companion and flash tool nothing is working.....
Is this an Hard brick, case, one of the technician suggested me an full flash through box, for which he will charge me INR 1500 (USD 30)...what do you think ?
surajpardeshi said:
I have tried all the method, right from SEUS, PC Companion and flash tool nothing is working.....
Is this an Hard brick, case, one of the technician suggested me an full flash through box, for which he will charge me INR 1500 (USD 30)...what do you think ?
Click to expand...
Click to collapse
U from India? Know hindi?
Sent from my X10 using xda premium
Me too BRICKED or Semi Bricked.... =(
First fail PCC
Then PCC Repair fail too
SEUS fail.
Took to different computer that was finally able to flash 2.1.1 update last year.
Clean install of pcc and seus Both still fail
In fact pic with yellow is from that fail & all others (Using Flashtool) except X10a_2.2.1.A.0.6_Rogers.ftf I get regular triangle with ! over top of phone pic after SE I've exhausted ALL my efforts and need guidance. I am super broke right now, so repair shop not good option. Two shops here in town say they will try, but NO PROMISES and still must pay for time
NEED True rescue fix here
Hindi yes
Yeah, I'm from Nashik, India, but I visit Mumbai frequently..
You, know any place where I can get this done in a cheaper way.....
surajpardeshi said:
Yeah, I'm from Nashik, India, but I visit Mumbai frequently..
You, know any place where I can get this done in a cheaper way.....
Click to expand...
Click to collapse
Right now i am bit busy. I will upload a pic for u as soon as i get free.
Sent from my X10 using xda premium
Using pcc... Even on "no phone connected"
Help us!!!
Can any1 out there help us fix tis problem or tell us what happen to our phone... or izzit our X10i is hopeless????
Pls help us....T_T
enzo1984316 said:
Can any1 out there help us fix tis problem or tell us what happen to our phone... or izzit our X10i is hopeless????
Pls help us....T_T
Click to expand...
Click to collapse
Did you try to read the above post at all?
Sent from my X10 using xda premium
i try PCC, SEUS and FLASHER.... All cannot work... i dunno what to do now...
btw... when my phone won't turn on that time my batt is low(Cos cannot charge) and debugging mode is off... izzit this problem make me can't do repair and reflash???
enzo1984316 said:
i try PCC, SEUS and FLASHER.... All cannot work... i dunno what to do now...
btw... when my phone won't turn on that time my batt is low(Cos cannot charge) and debugging mode is off... izzit this problem make me can't do repair and reflash???
Click to expand...
Click to collapse
Charge your battery using another x10 or any external charger
Sent from my X10 using xda premium
FIX!
I had the same issue when I was experimenting with ROMs and Recoverys, but not to worry, Sony PC Companion 2.1 does the trick!
Download PC Companion 2.1 from the Sony Mobile website
1. When you download and open it, click start under Support Zone
2. Click start under Phone Software Update
3. When the window saying that a phone could not be found appears, click repair phone
4. A windows like this will appear, click continue to proceed with the repair of the firmware
NOTE: All data that is placed on the phone memory will be wiped but any data saved on the memory card will be spared
5. After clicking continue, a window like so will appear. Tick the box and click next to continue with repair!
6. Sony PC Companion 2.1 will now prepare the computer for the firmware update
7. Now choose your phone model, in this case it should be the Xperia X10 (X10). Select the phone and click Next!
8. Follow the prompts to repair your phone!
GOOD LUCK!!
Always fails for me.
All process end in fail
There must be a file I need to rename or something....
tried everything now...
I have tried everything by now, here i have attached a attachment of error i get while repairing my phone through SEUS..
only option is box flash, but i think its kind of risky...
Fail fail fail..... i'm getting hopeless wif my X10
Hey,
I did some re-search and got to know that somehow my X10 flashes as So-01C in some systems, i.e. xperia arc, even while updating ..........
Anyone here, knows other ways to flash through box other than technician, coz these technicians are real idiot they can crap your phone in 10 seconds, so its better to crap it yourself...
"alternative to box flash, please ???"
Try this
Had the same problem once, when my phone would not start at all, all I had to do was connect it to the PC Companion (2.0), at first it wouldn't repair but after a certain amount of tries it did the trick,
First: Make sure all your drivers are installed, if they were installed there should be no problem.
If they were not, the computer cannot identify your phone, try installing some other x10's drivers (cause your's is bricked I assume) that might do the trick aswell.
Open PC Companion > Support Zone > Phone Software Update (Start) > Follow Instructions > Repair
It might take several tries to get it right
If this doesn't work try the latest flashtool, it should do the trick !!
There must be something you are not doing right, else SEUS/Flashtool should have worked like a charm.
see i get this reply, when updating x10..
I have tried this like thousands of times, installing roms and then removing them and repairing the phone, but this time it has gone over my head........
I need to flash my X10 Mini, but I can't find the firmware for It anywhere with a working link. Anyone that still have the file and willing to share?
There are only plenty of links to sites that are down
I tried to install MiniCM7-2.1.9-robyn on the phone and then afterwards it just won't start anymore, so i need to flash it and then use SEUS to restore it.
UPDATE!
I found everything and fixed everything I needed by just flashing It with a stock kernel.
Just use the Repair option in Pc Companion.
Here
leajian said:
Just use the Repair option in Pc Companion.
Click to expand...
Click to collapse
wont work because I can't even get into the menus, I turn it on and It gets stuck on a screen with little backlight, but no SE logo
TrissyGE said:
Here
Click to expand...
Click to collapse
I'm not looking for how to do It..... Read the question before you post. I appreciate you trying to help, but at least understand what the question Is first.
I'm looking for the firmware for the flashtool so I can flash my device (.ftf file)
They guides that teaches you how to fix a bricked phone got links to megaupload (that got shutdown not long ago) and multiupload (also got shutdown) for the firmware I'm looking for.
If you can't turn the phone on, then flashtool won't help you. You have to able to turn the phone on to get to download mode for flashtool, or Pc Companion, or SEUS to do their thing.
If your phone doesn't turn on, you've got a hard brick. Which is bad.
Sent from my U20i using xda premium
Ticklefish said:
If you can't turn the phone on, then flashtool won't help you. You have to able to turn the phone on to get to download mode for flashtool, or Pc Companion, or SEUS to do their thing.
If your phone doesn't turn on, you've got a hard brick. Which is bad.
Sent from my U20i using xda premium
Click to expand...
Click to collapse
No, it can be a hard brick, he didn't do anything to put his device in danger (from what he claims).
He just needs a stock .ftf file for mini, which I was planning to do in the past, but did only for the pro... I am sorry my friend... There is only one solution -to make the ftf file yourself, which is something very confusing and you are going to need another mini to do this. But don't get your hopes down, it is possible, at least...
leajian said:
No, it can be a hard brick, he didn't do anything to put his device in danger (from what he claims).
He just needs a stock .ftf file for mini, which I was planning to do in the past, but did only for the pro... I am sorry my friend... There is only one solution -to make the ftf file yourself, which is something very confusing and you are going to need another mini to do this. But don't get your hopes down, it is possible, at least...
Click to expand...
Click to collapse
The phone it self comes to a point where there is some light on the screen, but i can't see the SE Logo anymore. I can charge the phone without problem from what it looks.
If I can get hold of another mini how can I make the ftf?
What did I do to achive this problem??
I tried to install MiniCM7-2.1.9-robyn and it ended with a phone that got stuck during boot. Then I got to a guide where someone said "Hardreset the device and use SEUS", but SEUS always says that my phone has the latest software.
TazBaz said:
The phone it self comes to a point where there is some light on the screen, but i can't see the SE Logo anymore. I can charge the phone without problem from what it looks.
If I can get hold of another mini how can I make the ftf?
What did I do to achive this problem??
I tried to install MiniCM7-2.1.9-robyn and it ended with a phone that got stuck during boot. Then I got to a guide where someone said "Hardreset the device and use SEUS", but SEUS always says that my phone has the latest software.
Click to expand...
Click to collapse
As far as SEUS is concerned, you DO have the latest software. It just doesn't realise that what you have doesn't work. Select the option to reinstall the software.
Sent from my U20i using xda premium
Ticklefish said:
As far as SEUS is concerned, you DO have the latest software. It just doesn't realise that what you have doesn't work. Select the option to reinstall the software.
Sent from my U20i using xda premium
Click to expand...
Click to collapse
Only one problem here, I don't have the option to reinstall the software at all after it says that I already have the latest software.
Can it be that the option is no longer there depending on SEUS version?
TazBaz said:
Only one problem here, I don't have the option to reinstall the software at all after it says that I already have the latest software.
Can it be that the option is no longer there depending on SEUS version?
Click to expand...
Click to collapse
There is a repair option in PC Companion, see it, please! The repair option on PC Companion is Support Zone --> Update --> Repair.
BTW, to hard reset :
1. Turn the phone off
2. Press the POWER button
3. Press and hold home key aprox 3 seconds
4. The hard reset is starting.
Hello there!!! I had the same problem just yesterday and I was about to get crazy in order to solve it...and then I found this post which was definately useful!!!! Just follow every single step and it will get back to work...btw I still can't flash the nAa-11 kernel with flashtool...it keeps on saying error and the flashing doesn't work
http://forum.xda-developers.com/showpost.php?p=20251565&postcount=8
leajian said:
There is a repair option in PC Companion, see it, please! The repair option on PC Companion is Support Zone --> Update --> Repair.
BTW, to hard reset :
1. Turn the phone off
2. Press the POWER button
3. Press and hold home key aprox 3 seconds
4. The hard reset is starting.
Click to expand...
Click to collapse
I will try that thanks, but you need to hard reset before the repair with PC Companion?
I managed to find the stock kernel so now I'm starting the device, but I get a SE logo and then It shuts off.
One problem when I try to repair on step 2 (prepare step) I get a error unable to start or phone update update components. (the pc companions is installed with the newest version)
Hi. Basically, my phone is stuck on the Sony Ericsson screen. I know it can all be fixed by re-flashing or clicking on the repair bit on PC Companion however the usb port is broken on the phone and my local shop couldn't repair it. Does anyone have any suggestions? The phone is worth nothing otherwise...
By the way, it is rooted and stuck on the SE screen because i deleted the stock launcher and then tried doing a factory reset on the phone (face palm moment...)
Thanks!
I guess there are flashable home app zips on some threads here...I guess donut thread has it...copy it to memory card using a card reader....
Reboot to xrecovery...flash it......
sEnT fRoM AGNI-5 tRuE iNdiAN
Could you elaborate more please? i'm not familiar with the stuff you mentioned..
Thanks,
Thomas.
which rom are u using right nw ????
I was just using the normal rom but rooted? But obviously i can't give much more information because i can't get into my phone...
http://www.mediafire.com/?txrq1o0ii24jmr1
give this a try...am nt sure ...
try downloading this zip....then save it in some folder on ur sd card....using an sd card reader if ur usb port is broken....
then reboot into xrecovery n flash this zip....
this might help u n install go launcher on ur cell....n u can access home
How do you reboot into recovery? And can you definitely do it on my phone?
Thanks!
Go launcher womt help as he did a factory reset. U need to grab flashtool pal and use that to install global generic firmware. U could try seus or pc companion also they may help
Edit: sorry didnt see bit about broken USB u need to look at this:
http://forum.xda-developers.com/showthread.php?p=13287756
Sent from my X10S using XDA
But i can't use them because of the faulty usb port right?
I can't seem to get into any 'recovery' thing? I've booted whilst holding the back button?
Flashtool wont work for sure ...
U have done a factory reset right? ?? So as told above installing another zip also wont workout...
Xrecovery might have gone...
One more thing...for instance if recovery is working u have to press back button once the led starts blinking ....n tats hw u gotta boot into it...
TomAshby said:
Hi. Basically, my phone is stuck on the Sony Ericsson screen. I know it can all be fixed by re-flashing or clicking on the repair bit on PC Companion however the usb port is broken on the phone and my local shop couldn't repair it. Does anyone have any suggestions? The phone is worth nothing otherwise...
By the way, it is rooted and stuck on the SE screen because i deleted the stock launcher and then tried doing a factory reset on the phone (face palm moment...)
Thanks!
Click to expand...
Click to collapse
Get ur usb port fixed..
Sent from my Xperia S using XDA
Hi all,
It seems my X10 mini pro is completely bricked.
Firstly I root my phone
after that I copied the xrecovery and made a restart, till then everything was rolling smoothly.
I backed up and reseted to factory settings. loaded the new update.zip and after the restart that was needed my phone briked
it's not a common brick. I can't use flashtools to recover it.
here is the problem that appears...
6/030/2013 18:30:20 - ERROR - ERR_SEVERITY="MAJOR";ERR_CLASS="SECURITY_CLASS";ERR_DYNAMIC="SIN header verification failed"
16/030/2013 18:30:20 - ERROR - Error flashing. Aborted
Click to expand...
Click to collapse
phone is not responding to any command. Plus it needs to be turned off if you wanna restore the backup you saved previously...when I try to flash it, phone turns ON
I read many guides in this forum to unbrick it but didn't find anything that suits to my occasion.
If any other detail is missing from my report please ask me to add it.
Sorry for my english
Thanks in advance.
Use SEUS to restore Download from:
SEUS
Dont forget to pull of your battery for 4 seconds, for turn off your phone before connect your phone.
gnickz0r said:
Hi all,
It seems my X10 mini pro is completely bricked.
Firstly I root my phone
after that I copied the xrecovery and made a restart, till then everything was rolling smoothly.
I backed up and reseted to factory settings. loaded the new update.zip and after the restart that was needed my phone briked
it's not a common brick. I can't use flashtools to recover it.
here is the problem that appears...
phone is not responding to any command. Plus it needs to be turned off if you wanna restore the backup you saved previously...when I try to flash it, phone turns ON
I read many guides in this forum to unbrick it but didn't find anything that suits to my occasion.
If any other detail is missing from my report please ask me to add it.
Sorry for my english
Thanks in advance.
Click to expand...
Click to collapse
Press home and power buttons together, it will restart the phone, then start pressing the back-button repeatedly to get back into recovery and restore your previous rom from there. (Come to think of it, following my last paragraph below, you probably don't have recovery on your phone anymore, so, as Rempty mentioned above, repairing with SEUS or PC Companion would be the start to recover your phone to a usable state,.)
The error flashtool gave you is because you didn't unlock the bootloader and didn't change the kernel on your phone. It can't flash any non-sony kernel on a locked bootloader.
What is this 'update.zip' you're talking about? Most full roms have more informational names to distinguish between different zips. An update.zip is usually only for hotfixes to ROMS already flashed, and not a complete ROM.
Thanks a lot guys. I solve my problem with SEUS.
Phone completely formated.
Love you guys
Hey guys I hve instaled xrecovery and minicm9 too on my x10 mini pro I hve wiped chache,etc nd when I reboot , it hangs on SE logo plz help me
SE logo?? You forgot to install nAa kernel, do you unlock bootloader??, remember that minicm9 is not for stock kernel.
Sorry for my bad english
Sent from my iPhone6 using xda business
W'll when I try to unlock the bootloader it gives error can u plz help me
william chauhan said:
W'll when I try to unlock the bootloader it gives error can u plz help me
Click to expand...
Click to collapse
use flash tool to unlock ur bootloader
make sure ur fone is rooted
Sent from my U20i using xda premium
I'm already using flashtool bt it's nt working
william chauhan said:
I'm already using flashtool bt it's nt working
Click to expand...
Click to collapse
What's your phone's build date? Ex.11w37(written on the stick placed on the back )
Sent From My BEAST , I mean X8
My build no. Is 2.1.1.A.0.6
Plzz help me..
Plz help me.. I try to unlock the boot loader .. and the phone bricked !!!! what am i going to do??
i try the PC COMPANION but my phone did not detect it..
this is what i did to bring back life to my x10 mp.
Switch phone completely off then if not already running start pc companion. then this step really got to me because of the phone constantly restarting, to get pc companion to detect the phone, i pressed and held the back key down and connected the usb cable just like flashing a new kernel. pc companion then detected the phone as x10. doesnt matter. then start the update and you must do the same thing again to force update service to detect the phone and to give the option to repair. then once thats done follow the prompts through update service, it will then ask you what phone you have, choose x10 mini pro and update.its a long process but be patient and your phone will work again.
Hey guys I used the flashtool to unlock the bootloader and I also followed the steps too but problem is when the phone was rebooted it didnt read the sim card now what should I do ? Please help
thas911 said:
this is what i did to bring back life to my x10 mp.
Switch phone completely off then if not already running start pc companion. then this step really got to me because of the phone constantly restarting, to get pc companion to detect the phone, i pressed and held the back key down and connected the usb cable just like flashing a new kernel. pc companion then detected the phone as x10. doesnt matter. then start the update and you must do the same thing again to force update service to detect the phone and to give the option to repair. then once thats done follow the prompts through update service, it will then ask you what phone you have, choose x10 mini pro and update.its a long process but be patient and your phone will work again.
Click to expand...
Click to collapse
my phone is in HARD BRICKED.. my phone is dead the phone didnt charge and totally dead.. what should i do?? help me??
i also have a hard bricked,even when i put it to charge the phone its not blink the led
help