Hello All,
Please Help, I am trying to unlock my bootloader using the semcboot tool here (http://forum.xda-developers.com/showthread.php?t=1254087) but I am having an error on the process. Please let me know the solution for this.
I am qualified with this condition so I used this one - "If you can find semc simlock certificate in one of the last lines from the output, you can unlock your bl with the *semc.bat file"
but unfortunately, upon starting the tool, I encountered this error message. Please let me know what should I do. Thank you!
Code:
process requires standard 2.x android firmware.
Premere un tasto per continuare . . .
Getting ROOT rights.
* daemon not running. starting it now *
* daemon started successfully *
cannot stat 'bootTools\rageagainstthecage': No such file or directory
Unable to chmod /data/local/tmp/expl: No such file or directory
/data/local/tmp/expl: not found
Waiting ...
Removing NAND MPU restrictions via SEMC backdoor. Permanent. Require ROOT rights
.
3 KB/s (3087 bytes in 1.000s)
Unable to open router port: Permission denied
Diag_LSM: Diag_LSM_Init: Failed to open handle to diag driver, error = 13 ERR :
MSG Open handle failed, unable to open program 30eeeeee ver 10001 NOT FOUND
:FILE vendor/qcom-proprietary-qsd8k/oncrpc/oncrpc/oncrpc_cb.c:LINE 231:ARG1 82
0965102:ARG2 65537:ARG3 0:
ERR :MSG Couldn't setup RPC call :FILE vendor/qcom-proprietary-qsd8k/oncrpc/on
crpc/oncrpc_cb.c:LINE 276:ARG1 0:ARG2 0:ARG3 0:
Error: Failed to lookup client for 0x30EEEEEE 0x00010001
FATAL :MSG Failed to lookup RPC client. prog = 820965102, vers = 65537, tout =
0 :FILE vendor/semc/system/core/miscta/libmiscta/rpc_service.c:LINE 65:ARG1 820
965102:ARG2 65537:ARG3 0:
reboot: Operation not permitted
Waiting ...
Getting ROOT rights.
/data/local/tmp/expl: not found
Waiting ...
Writing patched semcboot. Two step process
First, we need get access to semcboot area
502 KB/s (8064 bytes in 0.015s)
insmod: init_module '/data/local/tmp/mapper_2.6.29.ko' failed (Operation not per
mitted)
Second, we need to write semcboot ;)
3054 KB/s (588228 bytes in 0.188s)
can't find userdate partition
Premere un tasto per continuare . . .
Please HELP!
same error here on sony erricson x10 rooted and xrecovery installed, baseband 2.1.71 with android stock 2.3.3
any help on this please?
my entire error lines from qsd8250_semc.cmd
Code:
process requires standard 2.x android firmware.
Press any key to continue . . .
Getting ROOT rights.
950 KB/s (585731 bytes in 0.601s)
Failed to set prot mask (Inappropriate ioctl for device)
Waiting ...
Removing NAND MPU restrictions via SEMC backdoor. Permanent. Require ROOT rights
.
35 KB/s (3087 bytes in 0.083s)
Unable to open router port: Permission denied
Diag_LSM: Diag_LSM_Init: Failed to open handle to diag driver, error = 13 ERR :
MSG Open handle failed, unable to open program 30eeeeee ver 10001 NOT FOUND
:FILE vendor/qcom-proprietary-qsd8k/oncrpc/oncrpc/oncrpc_cb.c:LINE 231:ARG1 82
0965102:ARG2 65537:ARG3 0:
ERR :MSG Couldn't setup RPC call :FILE vendor/qcom-proprietary-qsd8k/oncrpc/on
crpc/oncrpc_cb.c:LINE 276:ARG1 0:ARG2 0:ARG3 0:
Error: Failed to lookup client for 0x30EEEEEE 0x00010001
FATAL :MSG Failed to lookup RPC client. prog = 820965102, vers = 65537, tout =
0 :FILE vendor/semc/system/core/miscta/libmiscta/rpc_service.c:LINE 65:ARG1 820
965102:ARG2 65537:ARG3 0:
reboot: Operation not permitted
Waiting ...
Getting ROOT rights.
Failed to set prot mask (Inappropriate ioctl for device)
Waiting ...
Writing patched semcboot. Two step process
First, we need get access to semcboot area
94 KB/s (8064 bytes in 0.083s)
insmod: init_module '/data/local/tmp/mapper_2.6.29.ko' failed (Operation not per
mitted)
Second, we need to write semcboot ;)
951 KB/s (588228 bytes in 0.603s)
can't find userdate partition
Press any key to continue . . .
Related
Hello community!
I tried to unlock bootloader on my mini pro, unsuccessfully, of course
Now I have some questions, just to make things clearer.
Followed instructions from guide on this forum.
USB debugging mode is enabled. Here is log:
process requires standard 2.x android firmware.
Press any key to continue . . .
Getting ROOT rights.
* daemon not running. starting it now *
* daemon started successfully *
670 KB/s (585731 bytes in 0.852s)
error: protocol fault (no status)
Waiting ...
Removing NAND MPU restrictions via SEMC backdoor. Permanent. Require ROOT rights
.
110 KB/s (3087 bytes in 0.027s)
- exec '/system/bin/sh' failed: No such file or directory (2) -
- exec '/system/bin/sh' failed: No such file or directory (2) -
- exec '/system/bin/sh' failed: No such file or directory (2) -
Waiting ...
Getting ROOT rights.
- exec '/system/bin/sh' failed: No such file or directory (2) -
Waiting ...
Writing patched semcboot. Two step process
First, we need get access to semcboot area
474 KB/s (8064 bytes in 0.016s)
- exec '/system/bin/sh' failed: No such file or directory (2) -
- exec '/system/bin/sh' failed: No such file or directory (2) -
Second, we need to write semcboot
546 KB/s (596916 bytes in 1.066s)
- exec '/system/bin/sh' failed: No such file or directory (2) -
- exec '/system/bin/sh' failed: No such file or directory (2) -
Press any key to continue . . .
I suppose my mistake was trying to unlock on non-srandard ROM (MiniCM7pro v10).
I do not understand role of PC Companion in whole process. Is it used just to check connection between phone and PC? Do I have to really connect to PC Companion enabling USB Storage?
Thanx!
a kind of answer here
of course do not reflash miniCM7 2.0.7 since it is not for pro
but the other steps should work
(-Reflash Eclair with SEUS
-Root with SuperOne Click
-Unlock bootloader)
BACKUP before anything else !!!
Thank you Mat, can you also clarify PC Companion question?
cheers!
gstipe said:
Thank you Mat, can you also clarify PC Companion question?
cheers!
Click to expand...
Click to collapse
PC compagnon is needed for one thing : a driver needed for flashtool
if you don't want to install PCcompagnon, you need to install the driver :
in flashtool folder, go to drivers and install "ggsetup-2.2.0.10.exe"
I have it installed already, so no problem. Now I know why is needed!
Thanks mate!
Hi,
I could upgrade today to ICS and wanted to root with the Bin4ry package but i doesn't work
the phone opens the Backup Restore App and there is the RootMe Restore point.
Then I click the Restore buton, Now sometimes I get the Error: "Couldn't restore reconect external memory" and then a reboot and sometimes just a reboot
But no root!
I tried v9, v13 and v15
nothing works.
USB Debuging is active, sd card is removed
help
thanks
Code:
======================================================================
= This script will root your Android phone with adb restore function =
= Script by Bin4ry (thanks to Goroh_kun and tkymgr for the idea) =
= Idea for Tablet S from Fi01_IS01 =
= (13.10.2012) v15 =
======================================================================
Device type:
1) Normal
2) Special (for example: Sony Tablet S, Medion Lifetab)
x) Unroot
Make a choice: 1
Checking if i should run in Normal Mode or special Sony Mode
Please connect your device with USB-Debugging enabled now
1689 KB/s (147059 bytes in 0.085s)
remote object '/system/bin/ric' does not exist
.
Found Sony Backup-Restore.apk
LT26,LT22 etc. mode enabled!
.
Pushing busybox....
2447 KB/s (1085140 bytes in 0.433s)
Pushing su binary ....
3742 KB/s (91980 bytes in 0.024s)
Pushing Superuser app
4072 KB/s (996704 bytes in 0.239s)
Making busybox runable ...
.
Pushing fake Backup
3130 KB/s (73728 bytes in 0.023s)
Extracting fakebackup on device ...
Watch now your device. Select the backup named RootMe and restore it!
Starting: Intent { act=android.intent.action.MAIN cat=[android.intent.category.L
AUNCHER] cmp=com.sonyericsson.vendor.backuprestore/.ui.BackupActivity }
If all is successful i will tell you, if not this shell will run forever.
Running ......
Good, it worked! Now we are rebooting soon, please be patient!
Waiting for device to come up again....
Going to copy files to it's place
mount: permission denied (are you root?)
You can close all open command-prompts now!
After reboot all is done! Have fun!
Bin4ry
Drücken Sie eine beliebige Taste . . .
aexme said:
Hi,
I could upgrade today to ICS and wanted to root with the Bin4ry package but i doesn't work
the phone opens the Backup Restore App and there is the RootMe Restore point.
Then I click the Restore buton, Now sometimes I get the Error: "Couldn't restore reconect external memory" and then a reboot and sometimes just a reboot
But no root!
I tried v9, v13 and v15
nothing works.
USB Debuging is active, sd card is removed
help
thanks
Code:
======================================================================
= This script will root your Android phone with adb restore function =
= Script by Bin4ry (thanks to Goroh_kun and tkymgr for the idea) =
= Idea for Tablet S from Fi01_IS01 =
= (13.10.2012) v15 =
======================================================================
Device type:
1) Normal
2) Special (for example: Sony Tablet S, Medion Lifetab)
x) Unroot
Make a choice: 1
Checking if i should run in Normal Mode or special Sony Mode
Please connect your device with USB-Debugging enabled now
1689 KB/s (147059 bytes in 0.085s)
remote object '/system/bin/ric' does not exist
.
Found Sony Backup-Restore.apk
LT26,LT22 etc. mode enabled!
.
Pushing busybox....
2447 KB/s (1085140 bytes in 0.433s)
Pushing su binary ....
3742 KB/s (91980 bytes in 0.024s)
Pushing Superuser app
4072 KB/s (996704 bytes in 0.239s)
Making busybox runable ...
.
Pushing fake Backup
3130 KB/s (73728 bytes in 0.023s)
Extracting fakebackup on device ...
Watch now your device. Select the backup named RootMe and restore it!
Starting: Intent { act=android.intent.action.MAIN cat=[android.intent.category.L
AUNCHER] cmp=com.sonyericsson.vendor.backuprestore/.ui.BackupActivity }
If all is successful i will tell you, if not this shell will run forever.
Running ......
Good, it worked! Now we are rebooting soon, please be patient!
Waiting for device to come up again....
Going to copy files to it's place
mount: permission denied (are you root?)
You can close all open command-prompts now!
After reboot all is done! Have fun!
Bin4ry
Drücken Sie eine beliebige Taste . . .
Click to expand...
Click to collapse
I have the same problem and i think it error because "remote object '/system/bin/ric' does not exist" but now I haven't solution for this problem
aexme said:
Hi,
I could upgrade today to ICS and wanted to root with the Bin4ry package but i doesn't work
the phone opens the Backup Restore App and there is the RootMe Restore point.
Then I click the Restore buton, Now sometimes I get the Error: "Couldn't restore reconect external memory" and then a reboot and sometimes just a reboot
But no root!
I tried v9, v13 and v15
nothing works.
USB Debuging is active, sd card is removed
help
thanks
Code:
======================================================================
= This script will root your Android phone with adb restore function =
= Script by Bin4ry (thanks to Goroh_kun and tkymgr for the idea) =
= Idea for Tablet S from Fi01_IS01 =
= (13.10.2012) v15 =
======================================================================
Device type:
1) Normal
2) Special (for example: Sony Tablet S, Medion Lifetab)
x) Unroot
Make a choice: 1
Checking if i should run in Normal Mode or special Sony Mode
Please connect your device with USB-Debugging enabled now
1689 KB/s (147059 bytes in 0.085s)
remote object '/system/bin/ric' does not exist
.
Found Sony Backup-Restore.apk
LT26,LT22 etc. mode enabled!
.
Pushing busybox....
2447 KB/s (1085140 bytes in 0.433s)
Pushing su binary ....
3742 KB/s (91980 bytes in 0.024s)
Pushing Superuser app
4072 KB/s (996704 bytes in 0.239s)
Making busybox runable ...
.
Pushing fake Backup
3130 KB/s (73728 bytes in 0.023s)
Extracting fakebackup on device ...
Watch now your device. Select the backup named RootMe and restore it!
Starting: Intent { act=android.intent.action.MAIN cat=[android.intent.category.L
AUNCHER] cmp=com.sonyericsson.vendor.backuprestore/.ui.BackupActivity }
If all is successful i will tell you, if not this shell will run forever.
Running ......
Good, it worked! Now we are rebooting soon, please be patient!
Waiting for device to come up again....
Going to copy files to it's place
mount: permission denied (are you root?)
You can close all open command-prompts now!
After reboot all is done! Have fun!
Bin4ry
Drücken Sie eine beliebige Taste . . .
Click to expand...
Click to collapse
I got same problem, I don't know how to proceed !!! what a shame!!!
Hey,
I have the same problem with my sola (6.1.1.B.1.54) too. Do I have to unlock the bootloader before doing this? Isn't there a way to root without unlocking the bl?
Please help!
Thank you
Finally found my way out!!
It seems that the .54 firmware isn't vulnerable to bin4ary's exploit, you need to flash the .10 kernel first, root and the reflash the .54
Instructions:
http://forum.xda-developers.com/showthread.php?t=2029756
http://forum.xda-developers.com/showthread.php?t=2051692
Hope I helped the posters above me
aexme said:
Hi,
I could upgrade today to ICS and wanted to root with the Bin4ry package but i doesn't work
the phone opens the Backup Restore App and there is the RootMe Restore point.
Then I click the Restore buton, Now sometimes I get the Error: "Couldn't restore reconect external memory" and then a reboot and sometimes just a reboot
But no root!
I tried v9, v13 and v15
nothing works.
USB Debuging is active, sd card is removed
help
thanks
Code:
======================================================================
= This script will root your Android phone with adb restore function =
= Script by Bin4ry (thanks to Goroh_kun and tkymgr for the idea) =
= Idea for Tablet S from Fi01_IS01 =
= (13.10.2012) v15 =
======================================================================
Device type:
1) Normal
2) Special (for example: Sony Tablet S, Medion Lifetab)
x) Unroot
Make a choice: 1
Checking if i should run in Normal Mode or special Sony Mode
Please connect your device with USB-Debugging enabled now
1689 KB/s (147059 bytes in 0.085s)
remote object '/system/bin/ric' does not exist
.
Found Sony Backup-Restore.apk
LT26,LT22 etc. mode enabled!
.
Pushing busybox....
2447 KB/s (1085140 bytes in 0.433s)
Pushing su binary ....
3742 KB/s (91980 bytes in 0.024s)
Pushing Superuser app
4072 KB/s (996704 bytes in 0.239s)
Making busybox runable ...
.
Pushing fake Backup
3130 KB/s (73728 bytes in 0.023s)
Extracting fakebackup on device ...
Watch now your device. Select the backup named RootMe and restore it!
Starting: Intent { act=android.intent.action.MAIN cat=[android.intent.category.L
AUNCHER] cmp=com.sonyericsson.vendor.backuprestore/.ui.BackupActivity }
If all is successful i will tell you, if not this shell will run forever.
Running ......
Good, it worked! Now we are rebooting soon, please be patient!
Waiting for device to come up again....
Going to copy files to it's place
mount: permission denied (are you root?)
You can close all open command-prompts now!
After reboot all is done! Have fun!
Bin4ry
Drücken Sie eine beliebige Taste . . .
Click to expand...
Click to collapse
man 1st flash with 6.1.1.B.1.10
and root with binary method
and again flash with 6.1.1.B.1.54
and now you will see supersu or superuser on you menu screen
When i flash to .10 kernal my device says update software version availble but i cant update it from the sonny official site. and secondly my icons turn black,,, plz help
sukhera2 said:
When i flash to .10 kernal my device says update software version availble but i cant update it from the sonny official site. and secondly my icons turn black,,, plz help
Click to expand...
Click to collapse
ya don't update it but the icon is black and its normal now try with that binary root you have to sense the buttons in screen and you have to click restore and after restart your icon will be normal and you will see supersu or superuser on your screen menu...
I'm using the droidrzr.com as ldirected in the roms section.
phase 3 fails:
Code:
[*] Rebooting device...
[*] Waiting for phone to reboot.
[*] Phase three (this will take a minute)...
failed on '/data/logger' - Permission denied
mkdir failed for /data/logger, File exists
Unable to chmod /data/logger: Operation not permitted
link failed File exists
[*] Rebooting device...
[*] Waiting for phone to reboot.
[*] Phase four...
4558 KB/s (543080 bytes in 0.116s)
3804 KB/s (1867568 bytes in 0.479s)
3351 KB/s (476557 bytes in 0.138s)
3610 KB/s (63838 bytes in 0.017s)
[*] Cleaning up...
/system/bin/sh: su: not found
[*] Rebooting...
[*] Exploit complete!
[*] Press any key to exit.
Any suggestions.
I'm looking for a ROM to replace stock which supports USB OTG and allows disabling of the HDMI port. Wife passed her phone on to my son when we upgraded hers but its always detecting HDMI even if there is nothing plugged in. The disable detection setting in the stock JB rom only disabled for a short time.
Thanks
There be will be a video by therazrguy in YouTube for rooting all jellybean RAZRs.. That's an easy method...
You've to disable MotoDockService. Also i guess you're having the screen Force Portrait issue. If it's so, there's a root app to force orientation..
A friend of mine bought a refurbished RAZR and it has this issue
EugeneNine said:
I'm using the droidrzr.com as ldirected in the roms section.
phase 3 fails:
Code:
[*] Rebooting device...
[*] Waiting for phone to reboot.
[*] Phase three (this will take a minute)...
failed on '/data/logger' - Permission denied
mkdir failed for /data/logger, File exists
Unable to chmod /data/logger: Operation not permitted
link failed File exists
[*] Rebooting device...
[*] Waiting for phone to reboot.
[*] Phase four...
4558 KB/s (543080 bytes in 0.116s)
3804 KB/s (1867568 bytes in 0.479s)
3351 KB/s (476557 bytes in 0.138s)
3610 KB/s (63838 bytes in 0.017s)
[*] Cleaning up...
/system/bin/sh: su: not found
[*] Rebooting...
[*] Exploit complete!
[*] Press any key to exit.
Any suggestions.
I'm looking for a ROM to replace stock which supports USB OTG and allows disabling of the HDMI port. Wife passed her phone on to my son when we upgraded hers but its always detecting HDMI even if there is nothing plugged in. The disable detection setting in the stock JB rom only disabled for a short time.
Thanks
Click to expand...
Click to collapse
install this and do it so easy
Kingo Android Root
Hi!
You can try to download this app :
http://www.mediafire.com/download/n...1.3.6_Cekas+FIX+Sharebertron.blogspot.com.apk
AFAIK it's mod-ed version of RootMaster, the mod makes it easier to understand the Chinese words.
You'll receive notification from Google prior to installing saying that this app is unsafe since it's trying to break the android secure, but I think it's all fine, rooted my 4.1.2 JB XT910, when I was in ICS, TheRAZRGuy's method worked for me but ever since I flashed JB it wont work anymore. This worked well for me, no problems so far.
Hope this helped!
Q&A for [Z Ultra][TWRP][PhilZ Touch][CWM] XZDualRecovery Q&A
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [Z Ultra][TWRP][PhilZ Touch][CWM] XZDualRecovery Q&A. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
Cannot go to recovery
I have installed this dual recovery to stock rom and i managed to change my rom to Cm11 snapshot which is a great rom. however i was trying to go to recovery and apparently im not going anywhere. Yellow LED light up but im not going to any recovery at all even after pressing volume up or down upon boot up. what am i doing wrong and what would be a possible fix for this? any help would be appreciated.:crying: thanks
rojculanag said:
I have installed this dual recovery to stock rom and i managed to change my rom to Cm11 snapshot which is a great rom. however i was trying to go to recovery and apparently im not going anywhere. Yellow LED light up but im not going to any recovery at all even after pressing volume up or down upon boot up. what am i doing wrong and what would be a possible fix for this? any help would be appreciated.:crying: thanks
Click to expand...
Click to collapse
CM11 will have over written this recovery when you installed it. Just after you start the boot the LED should go purple for a second or two, press the vol up key then and you should endup in CWM
blueether said:
CM11 will have over written this recovery when you installed it. Just after you start the boot the LED should go purple for a second or two, press the vol up key then and you should endup in CWM
Click to expand...
Click to collapse
Thank you for the reply mate. Thats"s what i thought also, i try to go to CWM,when purple LED lights up, i would press volume UP but it would just be stuck on SONY logo and yellow LED would light up and that's it. I have to restart the phone. is it ok to reflash the recovery? or would there be any step that I need to do. Thanks. Very appreciated.
rojculanag said:
Thank you for the reply mate. Thats"s what i thought also, i try to go to CWM,when purple LED lights up, i would press volume UP but it would just be stuck on SONY logo and yellow LED would light up and that's it. I have to restart the phone. is it ok to reflash the recovery? or would there be any step that I need to do. Thanks. Very appreciated.
Click to expand...
Click to collapse
try flashing the boot.img again or try another one (Carbon/DooMLoRD's/etc)
blueether said:
CM11 will have over written this recovery when you installed it. Just after you start the boot the LED should go purple for a second or two, press the vol up key then and you should endup in CWM
Click to expand...
Click to collapse
blueether said:
try flashing the boot.img again or try another one (Carbon/DooMLoRD's/etc)
Click to expand...
Click to collapse
thanks. I finally was able to do it. thank you. now im trying out Android Lollipop Port and it's great.
Code:
==============================================
= =
= PhilZ Touch, CWM and TWRP Dual Recovery =
= Maintained by [NUT] =
= =
= For Many Sony Xperia Devices! =
= =
==============================================
1. Installation on ROM rooted with SuperSU
2. Installation on ROM rooted with SuperUser
3. Installation on unrooted ROM using the TowelRoot method
4. Install ADB drivers to windows
5. Exit
Please choose install action.
[1,2,3,4,5]?3
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
=============================================
Waiting for Device, connect USB cable now...
=============================================
Device found!
=============================================
Getting ro.build.product
=============================================
Device model is C6833
Firmware is 14.4.A.0.108
=============================================
Step2 : Sending the recovery files.
=============================================
mkdir failed for /data/local/tmp/recovery, File exists
0 KB/s (29 bytes in 1.000s)
15387 KB/s (15757 bytes in 0.001s)
0 KB/s (501 bytes in 1.000s)
11 KB/s (11842 bytes in 1.000s)
1790 KB/s (56834 bytes in 0.031s)
334 KB/s (3082 bytes in 0.009s)
0 KB/s (385 bytes in 1.000s)
1794 KB/s (657704 bytes in 0.358s)
1996 KB/s (2965760 bytes in 1.451s)
2494 KB/s (2599934 bytes in 1.018s)
2142 KB/s (1875823 bytes in 0.855s)
855 KB/s (8759 bytes in 0.010s)
=============================================
Step3 : Setup of dual recovery.
=============================================
=============================================
Attempting to get root access for installation using TowelRoot now.
NOTE: this only works on certain ROM/Kernel versions!
If it fails, please check the development thread (Post #2) on XDA for more detai
ls.
REMEMBER THIS:
XZDualRecovery does NOT install any superuser app!!
You can use one of the recoveries to root your device.
=============================================
=============================================
Sending files
=============================================
153 KB/s (1572 bytes in 0.010s)
1659 KB/s (13592 bytes in 0.008s)
cannot stat 'easyroottool\libexploit.so': No such file or directory
545 KB/s (9496 bytes in 0.017s)
1335 KB/s (13672 bytes in 0.010s)
Copying kernel module...
1122 KB/s (34473 bytes in 0.030s)
0 KB/s (765 bytes in 1.000s)
1659 KB/s (13592 bytes in 0.008s)
Kernel version is 3.4.0-perf-g0109737
Version does not match 3.4.0-perf-ge4322cd, needs patching...
1+0 records in
0+1 records out
19 bytes transferred in 0.001 secs (19000 bytes/sec)
Kernel module patched.
modulecrcpatch (by zxz0O0)
module_layout: match
__aeabi_unwind_cpp_pr1: match
kallsyms_lookup_name: not found
printk: not found
mem_text_write_kernel_word: not found
__aeabi_unwind_cpp_pr0: match
successfully patched
=============================================
Installing using zxz0O0's towelzxperia
(using geohot's towelroot library)
=============================================
towelzxperia (by zxz0O0)
thanks to geohot for libexploit
creating libzxploit.so
error: Could not open libexploit.so
/system/bin/sh: /system/xbin/busybox: not found
=============================================
Installation finished. Enjoy the recoveries!
=============================================
Aby kontynuować, naciśnij dowolny klawisz . . .
What am I doing wrong? Can anyone help? I have tried on the second laptop with the same result. Windows 7 x64.
Never mind. I didn't turn off antivirus.
Hi..
Wondering if I'm able to flash these cwm/ twrp
Into my togari 6833 (xperia z ultra)?
Error while installing on C6802 Xperia Z Ultra
==============================================
= =
= PhilZ Touch, CWM and TWRP Dual Recovery =
= Maintained by [NUT] =
= =
= For Many Sony Xperia Devices! =
= =
==============================================
1. Installation on ROM rooted with SuperSU
2. Installation on ROM rooted with SuperUser
3. Installation on unrooted ROM using the TowelRoot method
4. Install ADB drivers to windows
5. Exit
Please choose install action.
[1,2,3,4,5]?1
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
=============================================
Waiting for Device, connect USB cable now...
=============================================
error: more than one device and emulator
Device found!
=============================================
Getting ro.build.product
=============================================
error: more than one device and emulator
Device model is
error: more than one device and emulator
Firmware is
=============================================
Step2 : Sending the recovery files.
=============================================
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
=============================================
Step3 : Setup of dual recovery.
=============================================
error: more than one device and emulator
error: more than one device and emulator
Look at your device and grant supersu access!
Press any key to continue AFTER granting root access.
error: more than one device and emulator
Press any key to continue . . .
error: more than one device and emulator
error: protocol fault (status read)
error: more than one device and emulator
error: more than one device and emulator
=============================================
Installation FAILED!
Please copy and paste the contents of this
window to the DevDB thread for troubleshooting!
=============================================
Press any key to continue . . .
Problem while switching to recovery..
I installed recovery properly..
But when I am trying to switch recovery mod, It is directly switch on..
I am using a latest firmware 14.4.A.0.108..
Is there any solution for it??
I installed this successfully on my Z ULtra. However when I tried to do a nandroid backup or flash a custom rom i always face this error : cannot mount system ??
ANy solution to this ?
Thanks
Issues with Dual Boot Recovery
Hi,
Anyone can help me out?
I have an Xperia Z Ultra, freshly rooted with unlocked BL.
I installed Dual Recovery but for some reason, I can't reboot to any of the recovery this has to offer (PhilTouch, CWM, and TWRP).
Tried the physical button method and via NDR Utils with no success.
Looking at the log on the console, it looks like it failed to copy some files saying that a given directory is read-only but I checked using ES File Explorer that these directories are writable.
Can anyone help out as I would like to create a nandroid backup before messing with anything else just in case.
Anyway, here is the output of the installer console:
===========================================================
==============================================
= =
= PhilZ Touch, CWM and TWRP Dual Recovery =
= Maintained by [NUT] =
= =
= For Many Sony Xperia Devices! =
= =
==============================================
1. Installation on ROM rooted with SuperSU
2. Installation on ROM rooted with SuperUser
3. Installation on unrooted ROM using the TowelRoot method
4. Install ADB drivers to windows
5. Exit
Please choose install action.
[1,2,3,4,5]?1
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
=============================================
Waiting for Device, connect USB cable now...
=============================================
Device found!
=============================================
Getting ro.build.product
=============================================
Device model is C6833
Firmware is 14.4.A.0.108
=============================================
Step2 : Sending the recovery files.
=============================================
19 KB/s (30 bytes in 0.001s)
4728 KB/s (16947 bytes in 0.003s)
326 KB/s (501 bytes in 0.001s)
4656 KB/s (11920 bytes in 0.002s)
5842 KB/s (56834 bytes in 0.009s)
1504 KB/s (3082 bytes in 0.002s)
3271 KB/s (30148 bytes in 0.009s)
453 KB/s (1162 bytes in 0.002s)
2805 KB/s (34473 bytes in 0.012s)
225 KB/s (924 bytes in 0.004s)
1896 KB/s (13592 bytes in 0.007s)
375 KB/s (385 bytes in 0.001s)
5405 KB/s (719520 bytes in 0.130s)
5668 KB/s (3419065 bytes in 0.589s)
5123 KB/s (2431545 bytes in 0.463s)
6589 KB/s (1936442 bytes in 0.287s)
3477 KB/s (8902 bytes in 0.002s)
=============================================
Step3 : Setup of dual recovery.
=============================================
Look at your device and grant supersu access!
Press any key to continue AFTER granting root access.
-rwxr-xr-x 1 shell shell 719520 Apr 8 14:27 /data/local/tmp/recover
y/busybox
Press any key to continue . . .
##########################################################
#
# Installing XZDR version 2.8.5 RELEASE
#
#####
Temporarily disabling the RIC service, remount rootfs and /system writable to al
low installation.
insmod: can't insert '/system/lib/modules/wp_mod.ko': File exists
Copy recovery files to system.
Copy chargemon script to system.
Copy dualrecovery.sh to system.
Copy rickiller.sh to system.
Installing NDRUtils to system.
Copy disableric to system.
Copy busybox to system.
Trying to find and update the gpio-keys event node.
Found and will be using /dev/input/event5!
sed: can't create temp file '/storage/sdcard1/XZDualRecovery/XZDR.propGnS20I': R
ead-only file system
Trying to find and update the power key event node.
Found and will be monitoring /dev/input/event4!
sed: can't create temp file '/storage/sdcard1/XZDualRecovery/XZDR.propUUaD89': R
ead-only file system
Speeding up backups.
touch: /sdcard1/clockworkmod/.hidenandroidprogress: Read-only file system
Make sure firstboot goes to recovery.
sed: can't create temp file '/storage/sdcard1/XZDualRecovery/XZDR.propTcsuIy': R
ead-only file system
sed: can't create temp file '/storage/sdcard1/XZDualRecovery/XZDR.propT1eL2g': R
ead-only file system
=============================================
DEVICE WILL NOW TRY A DATA SAFE REBOOT!
=============================================
=============================================
Your installation has already cleaned up after
itself if you see the install.bat/install.sh exit.
=============================================
=============================================
Installation finished. Enjoy the recoveries!
=============================================
Press any key to continue . . .
=============================================
Hi sorry I just want to see if anyone can help me with my z ultra I can't get it to enter recovery with the hardware keys and the rom isn't working correctly so I can't do anything when It turns on all help appreciated
Anyone?
@[NUT], assistance please?
Thanx!
Resolved!
I removed the installation using the guide on the original thread and reinstalled a newly downloaded version (ZU-lockeddualrecovery2.8.8-RELEASE.installer.zip)
Just thought I'd place a feedback here.
Thanks!
Can this be installed on purely stock unrooted firmware? I'm on Lollipop .270.
Sent from my LG-F320L using Tapatalk
Failed install ZU Dual Recovery
Hi... sorry, i want to see if anyone can help me with my Z Ultra C6833 build number 14.4.A.0.108, I am failed install recovery.
Can anyone help me out, until success install Dual Recovery...
==============================================
= =
= PhilZ Touch, CWM and TWRP Dual Recovery =
= Maintained by [NUT] =
= =
= For Many Sony Xperia Devices! =
= =
==============================================
1. Installation on ROM rooted with SuperSU
2. Installation on ROM rooted with SuperUser
3. Installation on unrooted ROM using the TowelRoot method
4. Install ADB drivers to windows
5. Exit
Please choose install action.
[1,2,3,4,5]?1
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
=============================================
Waiting for Device, connect USB cable now...
=============================================
error: protocol fault (status read)
Device found!
=============================================
Getting ro.build.product
=============================================
error: more than one device and emulator
Device model is
error: more than one device and emulator
Firmware is
=============================================
Step2 : Sending the recovery files.
=============================================
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
=============================================
Step3 : Setup of dual recovery.
=============================================
error: more than one device and emulator
error: more than one device and emulator
Look at your device and grant supersu access!
Press any key to continue AFTER granting root access.
error: more than one device and emulator
Press any key to continue . . .
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
error: more than one device and emulator
=============================================
Installation FAILED!
Please copy and paste the contents of this
window to the DevDB thread for troubleshooting!
=============================================
Press any key to continue . . .
Hello I'm using a Xperia z ultra c6833 running stock lollipop 5.2 I have done nothing on it i dont have root my bootloader is locked keep in mind that lollipop has some problems I want to install a coustem rom can I use this method is there any other way please help me I'm losing hop please help
---------- Post added at 12:35 PM ---------- Previous post was at 12:14 PM ----------
Hello I'm using a Xperia z ultra c6833 running stock sony lollipop 5.0.2 I don't have root access and my bootloader is locked since lollipop has problems and it's really hard to get a coustem recovery in my situation can I use this method is there any other way I'm losing hop can any one please help
My tablet is a Lenovo Yoga Tablet 8 (B6000-F)
I'm going to try installing TWRP on my tablet, but because I couldn't find any official TWRP/CWM or even unnificial ports, I asked in a facebook group for help. A random guy gave me a 6MB .img file. (sorry but because of the dam new user restrictions I can't put the file in here) . How do I know if it's safe? I already tried opening the file, seeing its contents etc but I can't. I also tried mouting but with no sucess. I'm not any pro, but also not any noob.
How do I check if this is safe?
DarkAlpha.Sete said:
My tablet is a Lenovo Yoga Tablet 8 (B6000-F)
I'm going to try installing TWRP on my tablet, but because I couldn't find any official TWRP/CWM or even unnificial ports, I asked in a facebook group for help. A random guy gave me a 6MB .img file. (sorry but because of the dam new user restrictions I can't put the file in here) . How do I know if it's safe? I already tried opening the file, seeing its contents etc but I can't. I also tried mouting but with no sucess. I'm not any pro, but also not any noob.
How do I check if this is safe?
Click to expand...
Click to collapse
Look at these page. I think it help you. If it helps please thank me.
http://lenovo-forums.ru/topic/4517-...covery-для-b6000-wi-fi-и-3g-b8000-wi-fi-и-3g/
Ashwinrg said:
Look at these page. I think it help you. If it helps please thank me.
Click to expand...
Click to collapse
I cant say if that helped before when I go to fastboot mode to flash it give this:
Code:
sending 'recovery' (6128 KB)...
OKAY [ 0.234s]
writing 'recovery'...
FAILED (remote:
partition 'recovery' not support flash)
finished. total time: 0.242s
DarkAlpha.Sete said:
I cant say if that helped before when I go to fastboot mode to flash it give this:
Code:
sending 'recovery' (6128 KB)...
OKAY [ 0.234s]
writing 'recovery'...
FAILED (remote:
partition 'recovery' not support flash)
finished. total time: 0.242s
Click to expand...
Click to collapse
Try to flash recovery from given link. May be your recovery is not good.
Ashwinrg said:
Try to flash recovery from given link. May be your recovery is not good.
Click to expand...
Click to collapse
The link also doesn't work, I got this(my tablet has root, so thats not the problem):
Code:
---------------------set var---------------------------
-----------------detecting device----------------------
SUCCESS: The process "adb.exe" with PID 7100 has been terminated.
error: protocol fault (no status)
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
*A CENSORED SERIAL* device
--------------------copy boot--------------------------
7399 KB/s (4839424 bytes in 0.638s)
------------------copy recovery------------------------
7892 KB/s (6275072 bytes in 0.776s)
------------------copy protect_f-----------------------
7445 KB/s (10485760 bytes in 1.375s)
--------------------flash boot-------------------------
/dev/bootimg: cannot open for write: Permission denied
-----------------flash recovery------------------------
/dev/recovery: cannot open for write: Permission denied
failed: Operation not permitted
-----------------flash protect_f-----------------------
/dev/block/mmcblk0p2: cannot open for write: Permission denied
mount: Operation not permitted
Press any key to continue . . .
DarkAlpha.Sete said:
The link also doesn't work, I got this(my tablet has root, so thats not the problem):
Code:
---------------------set var---------------------------
-----------------detecting device----------------------
SUCCESS: The process "adb.exe" with PID 7100 has been terminated.
error: protocol fault (no status)
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
*A CENSORED SERIAL* device
--------------------copy boot--------------------------
7399 KB/s (4839424 bytes in 0.638s)
------------------copy recovery------------------------
7892 KB/s (6275072 bytes in 0.776s)
------------------copy protect_f-----------------------
7445 KB/s (10485760 bytes in 1.375s)
--------------------flash boot-------------------------
/dev/bootimg: cannot open for write: Permission denied
-----------------flash recovery------------------------
/dev/recovery: cannot open for write: Permission denied
failed: Operation not permitted
-----------------flash protect_f-----------------------
/dev/block/mmcblk0p2: cannot open for write: Permission denied
mount: Operation not permitted
Press any key to continue . . .
Click to expand...
Click to collapse
Set your system read/write and try again
Ashwinrg said:
Set your system read/write and try again
Click to expand...
Click to collapse
What do you mean?
DarkAlpha.Sete said:
The link also doesn't work, I got this(my tablet has root, so thats not the problem):
Code:
---------------------set var---------------------------
-----------------detecting device----------------------
SUCCESS: The process "adb.exe" with PID 7100 has been terminated.
error: protocol fault (no status)
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
*A CENSORED SERIAL* device
--------------------copy boot--------------------------
7399 KB/s (4839424 bytes in 0.638s)
------------------copy recovery------------------------
7892 KB/s (6275072 bytes in 0.776s)
------------------copy protect_f-----------------------
7445 KB/s (10485760 bytes in 1.375s)
--------------------flash boot-------------------------
/dev/bootimg: cannot open for write: Permission denied
-----------------flash recovery------------------------
/dev/recovery: cannot open for write: Permission denied
failed: Operation not permitted
-----------------flash protect_f-----------------------
/dev/block/mmcblk0p2: cannot open for write: Permission denied
mount: Operation not permitted
Press any key to continue . . .
Click to expand...
Click to collapse
Try these.
http://mobilecon.info/getting-permi...wm-in-android-4-0-3.html#sthash.pZS1K082.dpbs
Ashwinrg said:
Try these.
Click to expand...
Click to collapse
Well, I may just bricked this. I did everything as explained, no errors, now the tablet is stuck on the logo... YAY! Just bricked something today...
EDIT- From nothing it started working and I have TWRP in it! Thank you