I'm having an issue that has been bothering me. I run Etrade Pro with streaming data and charts, and when I leave my home, it does not automatically cut the wifi and switch to LTE or 4g. My app stops and says there is no data. This has happened a lot and I wonder if there are some settings that need to assure that mt cell signal automatically kicks in when Wifi cuts out.
ANother problem is that if I approach an area where there is wifi, the phone connects, and i usually get a data issue again.
I also got the same problem when i stream a video while on wifi and then leave the wifi zone, so I know it is not an Etrade app specific problem,
Any advice would be appreciated. What I am having to do is manually shut off wifi and then restart the app when the 4g kicks in, and I know the phone is designed to handle this for me.
lindenhurst said:
I'm having an issue that has been bothering me. I run Etrade Pro with streaming data and charts, and when I leave my home, it does not automatically cut the wifi and switch to LTE or 4g. My app stops and says there is no data. This has happened a lot and I wonder if there are some settings that need to assure that mt cell signal automatically kicks in when Wifi cuts out.
ANother problem is that if I approach an area where there is wifi, the phone connects, and i usually get a data issue again.
I also got the same problem when i stream a video while on wifi and then leave the wifi zone, so I know it is not an Etrade app specific problem,
Any advice would be appreciated. What I am having to do is manually shut off wifi and then restart the app when the 4g kicks in, and I know the phone is designed to handle this for me.
Click to expand...
Click to collapse
I'm not sure this is something we have control over, I was reading over a white paper qualcomm wrote on the matter: http://www.qualcomm.com/media/documents/files/3g-wifi-seamless-offload.pdf
Our phone is 3GPP R8 however, I'm not sure at&t's network supports dual stack mobile IP, so therefor the handoff between wifi and 3g would have to interrupt data.
WHat bothers me is that I just came from an Iphone4 and the iPhone switched from wifi to cell, and my Etrade App kept running. There may have been a momentary lag, but i didn't have to close the app and start it again.
Let me look into it more when I get home. At work youtube is blocked on the company network so I can't test if a video continues between handover here.
WHen I leave my home and know that I am out of wifi range, I still see the wifi symbol on the home screen but it looks like there are no bars of strength. It's like the thing is still trying to draw data through wifi that is well out of range.
Frustrating.
lindenhurst said:
WHen I leave my home and know that I am out of wifi range, I still see the wifi symbol on the home screen but it looks like there are no bars of strength. It's like the thing is still trying to draw data through wifi that is well out of range.
Frustrating.
Click to expand...
Click to collapse
So if the wifi symbol is on the status bar that means the phone is still connected to the wifi (or at least thinks it is).
I was not able to reproduce your problem with youtube when I was home. I started a video on wifi in my home, and then walked out the front door and down the hall until it lost the connection, the wifi symbol disappeared and it just had to re-buffer a little bit after it switched to LTE then the video continued.
Related
Hello everybody!
Someone of you has noticed a poor WiFi reception on Hero?
I'm experiencing a poor WiFi reception in my house when Hero is connect to internet thru an access point.
What happen is that after WiFi connection has been established the phone tends to loose it and restart connection thru GSM/3G link.
That happen also if phone stay in the same place without moving around and also when phone is close to access point location.
Any idea about way to solve the problem?
Regards.
Alex
ale.agos said:
Hello everybody!
Someone of you has noticed a poor WiFi reception on Hero?
I'm experiencing a poor WiFi reception in my house when Hero is connect to internet thru an access point.
What happen is that after WiFi connection has been established the phone tends to loose it and restart connection thru GSM/3G link.
That happen also if phone stay in the same place without moving around and also when phone is close to access point location.
Any idea about way to solve the problem?
Regards.
Alex
Click to expand...
Click to collapse
Just an upgrade on issue...
If I turn off data connection thru GSM/3G and switch on WiFi seem that WiFi connection is stable so maybe issue come when both data connection are enabled...
Anyway is annoying shout down each time data connection on GSM/3D and power on WiFi!
Regards.
i believe wifi goes idle when not in use. so it connect to 3g or edge. However there is an app if not various in the market already to help keep wifi always on..
Do a search for wifi and see for yourself.
minogue said:
i believe wifi goes idle when not in use. so it connect to 3g or edge. However there is an app if not various in the market already to help keep wifi always on..
Do a search for wifi and see for yourself.
Click to expand...
Click to collapse
Thanks for suggestion!
At now I've solved turning off GSM/3G data connection when I'm at home anyway I guess that WiFi reception sometimes go away due to issue of the phone or maybe as way to save battery...
when that happen phone stay unconnected so I guess that should be better if I will check for apps that keep WiFi connection always working!
Alex
when the device goes into standby, the wifi is turned off to save battery poweer, and it will go back to 3G.
go into the wifi settings, press menu and select advanced.
select the timeout options
set to never and it will not turn off when in standby.
problem solved and you shouldn't have to turn off Mobile data, although with the settings widget on your homescreen turning mobile data off off each time is hardly going to ruin your life. in fact i tend to do this anyway, just cos i have spent too many years with windows mobile....
Here's an annoying bug I've found tho - on TMob UK
If I send an MMS from home, wifi on, it sits there, and doesn't send the message. Until I turn off wifi and 3G kicks in again.
Now I know for a fact that on my Magic, it was able to turn on 3g/HSPDA to send the message all by itself. Might have a look in thodse advanced settings tho to see if there is something I can do.. Not a biggie, just a bit of an annoyance.
Dayzz
Dayzee said:
Here's an annoying bug I've found tho - on TMob UK
If I send an MMS from home, wifi on, it sits there, and doesn't send the message. Until I turn off wifi and 3G kicks in again.
Now I know for a fact that on my Magic, it was able to turn on 3g/HSPDA to send the message all by itself. Might have a look in thodse advanced settings tho to see if there is something I can do.. Not a biggie, just a bit of an annoyance.
Dayzz
Click to expand...
Click to collapse
I too, have been doing a search on Forums all over Google looking for a resolution to this.
I have noticed if Wi-Fi is enabled I am unable to send or receive MMS messages.
It is an annoyance having to turn Wi-Fi off each time also I am never to know if someone has tried to send a message in the first place.
Currently using T-Mobile G2 (rooted with MCR Rom 2.8) on T-Mobile UK
I am on bionix 1.3.1 and have noticed that whenever I turn my wifi on it seems to not allow me data access. My web browser will not connect to a page, market won't load, and any downloads that were in progress will fail. it's as if turning on the wifi is overriding my data connection and blocking it. It says that it's connected in the menu though. Any advice?
Thanks
Edit: I just noticed when looking at my phone stats, that when I turn on my wifi my mobile network state says disconnected, and it connects again when wifi is turned off.
Also, I have an airport extreme and a mac, perhaps that is my problem. I've scoured the internet and found a bunch of info about this problem, but haven't found anything that works yet.
Sent from my SGH-T959 using XDA App
Im sure someone will correct me if Im wrong but if you switch from wifi to 3g while downloading the download usually will fail because you were using only wifi to download the content and when that turned off it doesn't just switch to using 3g you have to manually retry the download using 3g .... when wifi and 3g are on wifi doesn't speed up the 3g instead it does the internet related work and the 3g does the text and phone call related work
that makes sense, thanks. as for the connection problem, it is definitely mac related. my wifi seems to work on other networks. I just need to figure out how to make it work with the airport. It's just weird to me that it says it's connected and shows signal bars, but won't access the internet.
jstein222 said:
that makes sense, thanks. as for the connection problem, it is definitely mac related. my wifi seems to work on other networks. I just need to figure out how to make it work with the airport. It's just weird to me that it says it's connected and shows signal bars, but won't access the internet.
Click to expand...
Click to collapse
so is the new problem that the airport extreme won't give wifi to your phone or that its not working at all
According to my phone I am connected via wifi to my network from the airport, however, the phone cannot access any internet functions when connected. When I disable wifi, it works fine with 3g or edge. It seems to be something with the settings on my airport, not the phone itself.
jstein222 said:
According to my phone I am connected via wifi to my network from the airport, however, the phone cannot access any internet functions when connected. When I disable wifi, it works fine with 3g or edge. It seems to be something with the settings on my airport, not the phone itself.
Click to expand...
Click to collapse
That's surprising maybe this means apple products are biased
Having problems with Wifi streaming and YouTube very slow, stop and start every few seconds, got to be the phone as all my other devices stream fine. I have unchecked avoid poor connections in wifi advanced.
Any one else having this problem, will try factory reset.
UK sim free 14w18, firmware 55
Sent from my D6503
I've seen factory resets cure a few problems on here so try that 1st but isn't there a .69 firmware available now as well, maybe try that to?
Sent from my GT-I9300 using XDA Premium 4 mobile app
Good old factory reset and it's working fine.....hasn't. Worked
EDIT.......wifi speeds are slow again, can't watch YouTube or stream films, it's only on this device, ipad 2, galaxy s3 and s2 all stream with no problems.
Can't download the 6 free promo films either as download fails after a short while.
Sent from my D6503
My facebook app is not working great in my phone. Youtube has been fine so far but I find my internet quite slow at home as I have rubbish internet speed. Also in peak times I get very slow internet connection.
Wifi speed still slow, only on this device,
Also is the . 69 firmware carrier specific?
No firmware update prompt on my phone.
no option for 5GHz in wifi advanced menu
Sent from my D6503
A couple of things to try:
* test with other access points
* restarting the router
* disconnecting other devices
* forgetting the network on the z2 and readding it
I actually got great wifi speeds with my z2. It was even able to max out a 100 Mbps cable broadband connection on an AC router. Worked fine in n-mode also.
Sent from my 2013023 using Tapatalk
Have you tested on any other networks?
Take a trip to Starbucks! See if you get any better speeds there (and a nice latte, damn I'd kill for one right now).
glas to see im not the only one. Google Play Store @ 0.02mb/s
What kind of router do you have and how far is it? I'm able to maintain 2-3MB/s (16-24Mbit/s) over a distance of 20 feet with walls and everything in between.
After getting my phone last Tuesday ive noticed this little bug as well, sometimes downloading/updating google play apps it'll be like 0.5MB/sec but usually when I use drop down menu and quick settings and turn off wifi(give it about 10/20secs) then reactivate it im back to around 8-14Mb/sec, some apps dont even show a download progress its that fast lol.
I believe it might be a 5Ghz wifi problem as my BT hub shows my phone connecting to 5GHz channel with no way to stop it apart from turning 5Ghz off at the router :/
So hopefully sony will either fix bug or give us more wifi options like already mentioned so we can make phone connect to what we want.
K stand corrected phone can/does switch between 2.4Ghz/5Ghz, router shows phone connected at 2.4Ghz now. Just updated an app while connected on 2.4Ghz and no problem.
Z2 D6503 Wifi dropping issues
I seem to be getting the same sort of wifi issues as previously stated. I cannot hold a wifi connection on the 2.4ghz band fro more than 20s before its dissociated (ie i still have full connection to the router (3 bars) but cannot get through to the internet). This happens no matter what router i am connected to, whether its at home or at work.
I have tried:
Setting the Wifi optimization checkbox off. No difference
Avoid poor connections is off. No difference.
Stamina mode is off. No difference.
Keep Wifi on during sleep is set to Always. No difference.
Sleep timeout to 30mins. No difference.
I have factory reset the phone. No difference.
I have also check to see if it is my router at home. I have switched between every channel available which made no difference. Security is Wpa/Wpa2 PSK AES which makes no difference. I only have the 2.4ghz available on that router at home (same at work).
My Note 3 and HTC One connect to both routers with no problems at all and do not drop out. Same goes with Sony Vaio Laptop.
I have installed Wifi Fixer on my Z2 to see if it can alleviate the problem and it does somewhat. instead of manually having to turn on and off the wifi toggle to reestablish a connection, the Wifi Fixer does it for me.Approx. every 20-30s in its log it will show the phone "dissociating" from the router, and the the app tries to "reassociate" the connection.
I can connect through wifi transfer to my Note 3 without issue, and the same goes for my TV, so it cant be a hardware fault, as the connection is still excellent strength for both (as well as the router, tested with Wifi Analyzer). This is a very frustrating problem as it makes watching youtube movies impossible, and hotspotting, skype calls, etc.....
And dont even get me started on the bluetooth dropouts. I am disconnected from a bluetooth connection every 66-70s without fail no matter what i try. No issues with my Note 3 and HTC One in the exact same conditions. It will disconnect then reconnect straight away with a delay of about 3 seconds, which makes calls and listening to music a VERY unpleasant experience.
Any ideas on how to fix this? I love everything else on this phone but this wifi/bluetooth connection issue is making it unusable.
connecting to my bt home hub 4 via 5GHz band only has solved my wifi drop out problems.
Sent from my iPad using Tapatalk HD
For me slow Wifi resulted in many issues, You-tube video cannot be played, video streaming from a network storage cannot be done, Facebook videos will stop at the middle etc where the most evident issues. I tried everything possible to resolve this issues and searching the internet also didn't help. Finally decided to fresh install, used PC companion and re-installed the complete software, then restored all apps using google backup service. After this there is no issue till now. The software version is the same I had before reinstall. But now the Video streaming and apps using internet become very responsive.
thanks
HCP
I have a new gear s on Verizon and have found the battery life very variable for lack of a better description. It appears the Verizon version does not display the same info in the moments bar as the Samsung manual shows or as I have seen on other carriers versions. I ask because my battery life in auto connect verses always off is a major difference even when connected to the phone via Bluetooth. It almost appears the 3G/4G is always on in the auto setting. worse case connected to the phone "note 4" via Bluetooth and network in auto I was getting 7 hours from 100% to 15% battery. If I turn the network off in the same situation I got over 40 hours and still had 25% battery left. Does anyone know if the Verizon version actually turns the network on/off in auto mode? Since they don't display this information in the moments bar you don't know if you are on, off or remotely connected. The 3G by the signal strength bar graph is always on whether you are on or in auto mode. Thanks for any help you might have.
I have the Verizon version also. When I'm by my phone Bluetooth automatically turns on and 3g turns off and vice versa. I had problems with it not automatically switching 3g off so I ran clean master from the Samsung store(made for Samsung phones) and ever since then it always works with auto connect
Sent from my SM-N915V using XDA Free mobile app
kieso said:
I have the Verizon version also. When I'm by my phone Bluetooth automatically turns on and 3g turns off and vice versa. I had problems with it not automatically switching 3g off so I ran clean master from the Samsung store(made for Samsung phones) and ever since then it always works with auto connect
Sent from my SM-N915V using XDA Free mobile app
Click to expand...
Click to collapse
Thank you for your response. I tried your suggestion but can see no immediate difference. If I may ask how do you know 3G/4G is turning on and off? On my watch the Bluetooth symbol in the moments bar will change either having the additional white triangles on each side when connected. The 3G/4G and signal strength bar graph is always there in the on or the auto. Only off will make them disappear. Thanks.
beast217 said:
Thank you for your response. I tried your suggestion but can see no immediate difference. If I may ask how do you know 3G/4G is turning on and off? On my watch the Bluetooth symbol in the moments bar will change either having the additional white triangles on each side when connected. The 3G/4G and signal strength bar graph is always there in the on or the auto. Only off will make them disappear. Thanks.
Click to expand...
Click to collapse
The 3g disappears and turns off the cell radio then connects to my phone Bluetooth. Double check your settings under connections, then mobile networks, make sure gear network is set to auto switch
Sent from my SM-N915V using XDA Free mobile app
Thank you once again for the information. I pretty sure mine is not working as it should. I have the 3G and signal strength bar graph if the mobile network is on or in auto phone connected Bluetooth and inches away. You need something to know if its on or off as you stated 3G there or off. The weird thing is with the network in auto and Bluetooth connected I put the phone in airplane mode then tried making a call from the watch. It would not do it. The 3G was there telling me the network is on but not making phone calls. I tried sending a text to the watch phone number with the network off and as expected it didn't come through even connected to the phone via Bluetooth. If the network is in auto and connected to phone via Bluetooth the text to watch phone number will come through. I'm guessing to get calls or texts to the watch phone number the network must be on. I'm curious if yours behaves as mine does. I have had the note 4 since January and its getting pretty cluttered with stuff plus add the lollypop update to the mix. I have tried a hard rest on the watch and think I'm going to do the same to the phone to clean house and try from scratch. Thanks again.
I did a search and didn't find anything so I apologize if this is a re-post. I can't figure out what function the Wi-Fi has on the Moto360 2. Does anyone have any insight on this?
Any help is appreciated. Thanks
I tried figuring this out too since my old gear 2 running wear didn't have wifi. from what I understand if you disconnect from Bluetooth, if you're on a wifi network you can get notification on your watch still no matter where your phone is. your phone can be on the wireless network and not wifi, and still through Google cloud services can send notifications to your watch. you can be like anywhere in the world I presume, and if your watch is on wifi, then you'll get notifications still
Sent from my Samsung Galaxy Note 4
jayochs said:
I tried figuring this out too since my old gear 2 running wear didn't have wifi. from what I understand if you disconnect from Bluetooth, if you're on a wifi network you can get notification on your watch still no matter where your phone is. your phone can be on the wireless network and not wifi, and still through Google cloud services can send notifications to your watch. you can be like anywhere in the world I presume, and if your watch is on wifi, then you'll get notifications still
Sent from my Samsung Galaxy Note 4
Click to expand...
Click to collapse
That's what I was thinking and I tested that out today without any success. But I think it's because I'm at work and the WiFi situation here is not the best. I'll test at home. Thanks
What the wifi functionality on the watch does, as it did on the 1st gen, is allow communication from your phone to the watch when the watch is out of bluetooth range. You have to be on the same wifi network with the watch and phone currently. There is no current multiple network communication at the moment, though I hope they implement that in the near future. If my hue lights can do it, my damn watch should be able to
FusionTechFTS said:
What the wifi functionality on the watch does, as it did on the 1st gen, is allow communication from your phone to the watch when the watch is out of bluetooth range. You have to be on the same wifi network with the watch and phone currently. There is no current multiple network communication at the moment, though I hope they implement that in the near future. If my hue lights can do it, my damn watch should be able to
Click to expand...
Click to collapse
Thanks for clearing that up. So the WiFi functionality is basically useless. If my phone and my watch are on the same WiFi network, then the chances are extremely high that they are both also within bluetooth range of each other. Adding to that, the fact that you need your phone to connect to a WiFi network in the first place really defeats the object of having WiFi on the watch at all. So if you're out and about without your phone, there is no chance for you to hook up with a WiFi hotspot.
If my Nexus 6p is connected to 5ghz wifi and my moto 360 2 is connected to 2.4ghz wifi on the same network will i have notifications if i lose bluetooth range?
Mister-B said:
Thanks for clearing that up. So the WiFi functionality is basically useless. If my phone and my watch are on the same WiFi network, then the chances are extremely high that they are both also within bluetooth range of each other. Adding to that, the fact that you need your phone to connect to a WiFi network in the first place really defeats the object of having WiFi on the watch at all. So if you're out and about without your phone, there is no chance for you to hook up with a WiFi hotspot.
Click to expand...
Click to collapse
It's great for me when I'm at home or in the office since bluetooth drains the phone battery much quicker than WiFi. Outside of that benefits are pretty limited.
it's not true though. they don't have to be on the same network. when my phone is 4g and watch is wifi, i still get it. that's because google cloud services are running on the phone and upload and the watch receives it.... just like how my Flux wifi bulb can be accessed remotely from another network and 4g.
Sent from my Note 4
jayochs said:
it's not true though. they don't have to be on the same network. when my phone is 4g and watch is wifi, i still get it. that's because google cloud services are running on the phone and upload and the watch receives it.... just like how my Flux wifi bulb can be accessed remotely from another network and 4g.
Sent from my Note 4
Click to expand...
Click to collapse
I can confirm this. Working on different networks. Wifi plus 4G working fine.
TweakBoxed H815 V10d
Do notifications on the watch work if the phone is off or dead? What I'm getting at is do the notifications actually come from the phone over wifi or do they come directly from google services?
I have been trying this on my wifi network with no luck. My phone is on my 5ghz wifi and the watch can only do 2.4 (I live in an apt and the 2.4 spectrum is absurdly saturated), I do not get alerts when my phone is out of range (rare since my apt is small).
I like the feature a lot if it worked correctly, it means my phone can sit charging somewhere (IE my room) and I can be around doing things and still get alerts. I will have to do more testing tonight. I might try turning bluetooth off on my phone and see if I still get alerts to my phone.
Still new to the smartwatch world but I love my 360