Related
hi can someone please help i tried to flash my xperia x10 mini and failed badly and now when i turn on my phone the logo screen comes up and then just stays on... ive left it for about 20 minutes but still nothing its like its bricked on the logo screen i can restart it but it just does the same again. Ive also tried taking the battery out putting it back in then using the update service to lock it in flash mode while i use binarys flash kit but that doesnt work either. Also the update service just says no software update is available it thinks i already have the latest one please help i will be truely greatful x
Edit :
Ive already tried SEUS, PC Companion, Binary's Flash Kit.
Ive already tried connecting it to the adb but cant get adb to recognise a connected device and all the drivers are installed.
i guess you have, but i've to ask, have you tried the repair option in SEUS/PC Companion?
yeh i have seus says i already have the latest software version installed and pc companion actually wants me to load my phone up to connect it :/ any ideas? x
me too!!
i had the same problem with you...
how to get shutdown this phone?
phone must be shutdown when i want to flashing from SEUS..
and i don't know how to shutdown this phone because the battery....
edit : just connect your phone and use restart (hold power button & middle button)
after reboot, press back button and you will connect with SEUS...
but, my phone already get latest update...and i can't flashing from SEUS...
sob..
ive been shutting down the phone by taking the back off and unscrewing the inside cover. Then you will see the battery cable where you can simply unplug it from the motherboard and then reinsert it.
Edit: I also have connected to SEUS but it says i already have the latest software
Ive taken it to a local phone repairs shop ive given up... they said it'll be fresh and working by tomorrow morning it cost me £20 but its just one of those things en it :/
hey guys
all you need is to follow the instructions on SEUS,
when it tells you that you have the latest software press repair.
and when it say that you should turn off your phone and then reconnect it while pressing the back buttom do the following:
1- connenct the phone to the computer
2- press the 3 buttoms (power + mid buttom + back buttom) then as your phone restarts and vibrate remove your fingers from the power and mid buttoms but maintain pressing on the vack buttom
i hope this will help
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
jakadewantara said:
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
Click to expand...
Click to collapse
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
try thread from DoomLORD : [DEV][How-To] Get Back to Stock Even With Broken / Damaged USB Port in http://forum.xda-developers.com/showthread.php?t=1054818
tarzerixx said:
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
Click to expand...
Click to collapse
Likely the USB port is dead and you have to send it in for repair.
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
pccobra said:
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
Click to expand...
Click to collapse
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
RedAxe said:
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
Click to expand...
Click to collapse
Hapenned the same to me...
I try to follow the steps, but i can't pass step 4 (it's unavaiable the "clean cache" bottom...)
Please help...
Restore original firmware with SEUS
RedAxe said:
...then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen...
Click to expand...
Click to collapse
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
do u have trick for my problem here forum.xda-developers.com/showthread.php?t=1388476
my x10 just vibrate once and stack on blank screen.
Sent from my X10i using Tapatalk
When I use SEUS It keep saying "You have the newest software available"
I tried the hard reset and all. The phone now just won't start at all
Hi,
i got the same problem what you describe ive stuck at the SE logo and cant get into recovery and i cant use flashtool. i tried to do what you say in the first post, but when i press the shell root button, it says "wait for device" then its not responding, and i cant moce on to the next step... what should i do now?
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
u totally saved me =D
X10 mini revived!
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
cruzstar said:
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
Click to expand...
Click to collapse
Update phone using SEUS....
Just google SUES
Definitely it will work....
Sent from my X10i using xda premium
yea i have use the SEUS..by pressing the back button..but it dont work..plz help me
Dear sir i already done that procedures but no use in seus shown u already updater software. plz help me
Cannot unbrick xperia mini E10i
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
Hello Guys,
I need your urgent help.
I cannot restore phone with SEUS or Companion. It says I already have the soft.
Getting fatal errors in Flashtool, I am stuck with SE logo and bootloader relocked.
I have the stock kernel but CM7 ROM.
Do you have any other ideas?
Tanks a lot!
deBelch said:
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
Click to expand...
Click to collapse
nope...didnt work...there is NO Install beneath...wonder why? is it i am using the latest SEUS?
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few seconds it boot automatically. and when i try to flash anything it boot automatically. please help me
---------- Post added at 12:21 AM ---------- Previous post was at 12:16 AM ----------
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few minutes it boot automatically. and when i try to flash anything it boot automatically. please help me
My phone was working, I had MiniCM7Pro V21 Installed and I tried to install the CWM Recovery Version 5, because in my installed version the Battery Stats Wipe wasn't working and my battery was draining very quickly.
After the CWM Recovery Version 5 Installation my phone got bricked because it's getting stuck in Sony Ericsson Text.
I am trying to Reflash but only Flash button is active and it doesn't show any firmware though I have copied both zip and unzipped files in firmware folder in FlashTool_0.2.9.1
I tried to use SuperOneClick to root but it gets stuck in Waiting for device. Kindly help.
It gives the following error :-
OK
Pushing rageagainstthecage...
error: device not found
FAILED
I have installed it.
ggsetup-2.2.0.10
Press home+power button until you see black screen, then immediately press and hold back button plugging your phone into computer. When you see black screen and green flashlight-> your phone is correctly booted into restore mode. From this mod, you can restore your phone, using SE restore tools: SEUS and Sony Ericsson Pc Companion, or flash stock kernel using flashtool.
P.S. If you wont see black screen and green flashlight for the first time, try it again, again until you putt your phone safely into restore mode.
Thank you for the reply, the black screen do u mean the black screen with Sony Ericsson Text ? When I Press Home+Power Button I can see the Sony Ericsson Text Black Screen and then I press and hold the back buton Pluging my phone into computer I keep on seeing the Sony Ericsson Text Black Screen with no green flashlight.
I am still trying.
Black screen without any logos. Just black screen. Don't forget to hold back button.
Doing that, but it still gets into Sony Ericsson Text Screen, I press home and the power button, black screen for a while and I press back button and try to connect the phone the Sony Ericsson logo appears.
But When the cable connected and back button pressed the I can see the charging image and green light flash.
and in Flasher it shows the following :-
07/007/2012 23:07:36 - INFO - Device connected with USB debugging off
07/007/2012 23:07:36 - INFO - For 2011 devices line, be sure you are not in MTP mode
camelgrg said:
Doing that, but it still gets into Sony Ericsson Text Screen, I press home and the power button, black screen for a while and I press back button and try to connect the phone the Sony Ericsson logo appears.
But When the cable connected and back button pressed the I can see the charging image and green light flash.
and in Flasher it shows the following :-
07/007/2012 23:07:36 - INFO - Device connected with USB debugging off
07/007/2012 23:07:36 - INFO - For 2011 devices line, be sure you are not in MTP mode
Click to expand...
Click to collapse
reflash to stock kernel and ROM
- install PC companion.
- connect phone in repair mode
- install drivers.
- after driver installed, reflash stock kernel using flashtool
- after stock kernel installed, reflash stock ROM using PC companion
- after stock kernel and ROM flashed,your phone should be like just when you bought it.
- bootloader should be locked now
- Root again
- unlock bootloader again
- Flash nAa again
- Flash cm7 again
- DONE!
Thank you for your reply, I have PC Companion Installed, I have a Generic Firmware downloaded, I have no idea what a stock kernel is ?
I am not able to get into this repair mode, I think this mode is when the flash light flashes ?
from the Bootloader part, I think I can do it because I did it before following a tutorial. If you can lease help me with the prior stage to bootloader lock would be highly grateful.
Thank u
Ones again: to enter restore mode you have to power off your phone, using home+power buttons or powering off like I have on picture. Then press and hold back button, while plugging it into computer.
camelgrg said:
Thank you for your reply, I have PC Companion Installed, I have a Generic Firmware downloaded, I have no idea what a stock kernel is ?
I am not able to get into this repair mode, I think this mode is when the flash light flashes ?
from the Bootloader part, I think I can do it because I did it before following a tutorial. If you can lease help me with the prior stage to bootloader lock would be highly grateful.
Thank u
Click to expand...
Click to collapse
- To relock bootloader you need to flash stock kernel which is 2.1.0.a.06 kernel.
- You need to flash stock kernel because if you have nAa kernel or any custom kernel installed, you wont be able to repair your phone using pc companion.
- After flashing stock kernel:
1. open pc companion
2. click support zone. (click start below it)
3. after clicking start, there should be a new window which also has a "start button"
4. on the 2nd start button, there should be a button under it which says "repair"
5. after clicking repair, just follow the steps for you to connect your phone in repair mode.
6. complete the repair installation.
7. DONE!
8. Bootloader should be locked now.
Thank you I was able to restore through PC Companion by getting into repair mode, however I didn't use flashtool to flash prior to usin PC Companion.
Thank you both for your kind support, Highly appreciated.
camelgrg said:
Thank you I was able to restore through PC Companion by getting into repair mode, however I didn't use flashtool to flash prior to usin PC Companion.
Thank you both for your kind support, Highly appreciated.
Click to expand...
Click to collapse
You are welcome my friend
And how should I proceed if I have a really hard brick (u20a)?
I tried to flash nAn on it, followed some instructions to unlock the bootloader, but something went wrong, the results were not the ones that should had been, and I made the mistake of turning it off. Now whenever I try to power it on, it doesn't do squat.
The only thing that makes me think it's still alive is that (after several months) I plugged it in and it began blinking on red (perhaps really low battery).
I've tried to pull the battery, put it back in, press back (keeping it pressed), and then plugging the cable to the computer and nothing.
Any ideas? Or should I flush it down the toilet? :crying:
x10 mini unbricking
Mrakoris/ said:
Press home+power button until you see black screen, then immediately press and hold back button plugging your phone into computer. When you see black screen and green flashlight-> your phone is correctly booted into restore mode. From this mod, you can restore your phone, using SE restore tools: SEUS and Sony Ericsson Pc Companion, or flash stock kernel using flashtool.
P.S. If you wont see black screen and green flashlight for the first time, try it again, again until you putt your phone safely into restore mode.
Click to expand...
Click to collapse
i tried the thing you suggested, but the green light only lasts a while even if i continue to hold the back button. also, i am not able to repair my phone through se pc companion, as it keeps cancelling the repair update the moment the green light stops appearing. any help? thanks!
my phone only gets to the se logo , and stops there :\ i have been able to safe mod-ing it by pressing left key or after turned on... because when i press the tree buttons below the screen, not anything at all happen before i release them i cant turn the phone on having buttons pushed down. have to release it to get any kind of start logo. that sony ericsson mobile in the first when turn off phone. second one is the se logo.. plz help me. i got the safe mode once in a 20-30times. but now i have the cable so when im in safemode im gonna repair
try to go to recovery and factory reset all setting
Trying to Flash Sony Ericsson MK16i using Flashtool. The phone is currently stuck in now well known - Sony Logo -> Xperia Logo -> Back to Boot Cycle and Sony Logo - Boot Loop.
I have installed Flash tool latest version (9.19.5). Have also installed Sony Xperia Common Drivers using Flash Tool's Driver.exe (V 1.8).
The phone was switched off; then the back button was held down and the USB cable connected to phone. The tool fails to detect Phone. The animation screen, one that shows the button to be used and the USB cable connection continues even after connecting the cable with BACK button pressed. In this case, the power LED turns green as expected.
Can not use even BLU or FAST BOOT. In case of BLE, the device is not detected.
In Case of Fastboot - The LED turns BLUE as expected when the USB cable is connected to the phone while pressing MENU button. But, even here, the phone is not recognized.
The Flash tool's DEBUG log does not show whether it tried to establish connection or why the connection is failing.
Any help/Advise will be much appreciated.
Warm Regards,
Ravi