[Q] Help: Touchpad bootlooping, MD5 sum mismatch and more - TouchPad General

Not...really sure what I did wrong, but I would love some help here. I wanted to install Kang with Cornerstone from the old Alpha .6. Booted into recovery, wipe data, wipe cache, flash, flash Gapps, boom. Works fine at first. After playing around with it, I decide I don't like how it tiles apps, so I switch to the latest kang build (2012 02 29), same thing. Wipe, flash aaaand...bootloop. I go back, attempt to flash again, perhaps foolishly, and it now restarts recovery when it gets about halfway through.
I then try to restore to the backup I had made a few hours prior, MD5 sum error. Note that I had about 5 gigs free at the time. I try an older backup I had, same thing. If its worth anything, the backup thinks it was made on march 1st, which hasn't happened yet where I am.
So now I'm completely locked out of android. Thankfully, I can at least boot back to WebOS, so its not completely fried. Is there something I can do here to fix this, or am without a paddle here? I'm thinking it might be fixed if I completely remove android and redo the whole process, but is there anything else I can do first?
Will reward help with e-hugs

Semianonymous said:
Not...really sure what I did wrong, but I would love some help here. I wanted to install Kang with Cornerstone from the old Alpha .6. Booted into recovery, wipe data, wipe cache, flash, flash Gapps, boom. Works fine at first. After playing around with it, I decide I don't like how it tiles apps, so I switch to the latest kang build (2012 02 29), same thing. Wipe, flash aaaand...bootloop. I go back, attempt to flash again, perhaps foolishly, and it now restarts recovery when it gets about halfway through.
I then try to restore to the backup I had made a few hours prior, MD5 sum error. Note that I had about 5 gigs free at the time. I try an older backup I had, same thing. If its worth anything, the backup thinks it was made on march 1st, which hasn't happened yet where I am.
So now I'm completely locked out of android. Thankfully, I can at least boot back to WebOS, so its not completely fried. Is there something I can do here to fix this, or am without a paddle here? I'm thinking it might be fixed if I completely remove android and redo the whole process, but is there anything else I can do first?
Will reward help with e-hugs
Click to expand...
Click to collapse
Did you use ACME uninstaller?
Your best bet is to wipe everything, and reinstall. Hell, while you're at it, if it were me I'd check for WebOS updates first.
It'll be fine after a complete reinstall, but I think that's not only your best option but just about your only one.
Unrelated, but FWIW:
For anyone who's ever said, "I wish I could just get rid of WebOS altogether, so I could have that extra space". This situation is why we don't want to even be able to do that.

Related

How I fixed my phone

So i'm going to consolidate and give everyone a brief recap on how I fixed my phone since it required the use of SEVERAL posts. I figured someone will eventually get caught in the same situation I was.
This is by no means the best way, or the correct way to fix any phone, do this at your own pace and liability. I am, and no one mentioned in this thread is liable for your phone.
Please excuse any of my grammar mistakes, this is spewing out as I type.
History: Stock DI01 update w/ JT's Voodoo .2 OC Kernel.
Flashed JT's Super Clean ROM V.4 & Remix Incognito Theme.
** Market would no longer work. I had this issue before updating to the 2.2 market after the DI01 update, so I uninstalled and worked again, however, that option wasn't available with the ROM Flash.
I couldn't find a single fix that would work to get the market to work, even ADB pushing older market apk's to the system wouldn't fix it. I decided to do a flash of JT's Super Clean ROM V.2, that didn't fix the issue either.
**I was clearing data and wiping dalvik after each flash**
With nothing seeming to work, I decided to try Deodexe's Zinc ROM, and this is where **** hit the fan. After doing this, I sent my phone into FC boot loop hell. I was getting the process.acore FC everytime I pressed a key. I rebooted back into Clockwork, tried to recover from an old ROM I had backed up the previous day, notta. Damage was done. I was getting FC bootloop hell with a very crappy performance.
I decided it was time to Odin restore and start over. These aren't the exact steps I took, but if I had to do it over again, this is how I would do it. If at any point you're getting a process.media FC, remove your SD Card, and leave it out until you need it for CWM.
STEP ONE:
If you installed Voodoo (at any point, removed or not, do this step)
Thanks to adrynalyne
http://forum.xda-developers.com/showthread.php?t=804784
This was the main culprit behind my phone not working correctly after a complete restore. I moved this to the top of the list, because after that, it's downhill.
STEP TWO:
Completely Restore with Odin Restore Files
Thanks to fallingup
http://forum.xda-developers.com/showthread.php?t=782204
The instructions are a little un-clear, but do this. First, Only use the PDA option, and flash each backup one at a time along with the PIT file. You're not out of the clear yet. Read on.
STEP THREE:
Flash CWM Recovery (read my notes below)
Thanks to fallingup
http://forum.xda-developers.com/showthread.php?t=788099
After you've flashed CWM. Boot into CWM Recovery, Boot back in Stock Recovery and wipe data and cache. Boot back to CWM (select sd:update.zip) and do the exact same thing there. Reboot phone.
STEP FOUR:
Do a data factory reset
Even though you have just restored the **** out of your phone, you're still not there. Get through all the account setup fields and go to Settings > Privacy > Factory Data Reset.
After a reboot, you should be on your way to a completely 100% stock fixed phone. At this point, I would suggest making a ROM back up of this point before moving ahead with flashing again.
LAST STEP (for me anyway):
Restore apps via Titanium Backup
This restored most my apps and settings that I had already saved, including LauncherPro and the backups I had for that. If you haven't used Ti, then use whatever app backup app you do have, if you do indeed have one.
I decided to re-flash JT's Super Clean ROM V.4 found here. Thanks to JT
http://forum.xda-developers.com/showthread.php?t=796171
I am also running the Remix Incognito Theme here: Thanks to frostman89
http://forum.xda-developers.com/showthread.php?t=801867
Right now I'm mixed on updating a new Voodoo Kernel, I haven't decided if I want to do that again or wait for something else.
Thanks again for all the DEV support, hopefully someone searching will find this thread useful.
Pretty much my standard routine when trying new kernels.
I have a nandroid with my basic rooted setup (apps and data intact), so this doesn't set me back by a huge amount.
Just a few differences...
I use:
Odin (System, then kernel) (step only needed if things are *really* messed up...won't boot)
Boot into Recovery
flash update.zip to get into CWM
Wipe Data/Cache/Davlik
Reboot into recovery
run jt's voodoo_uninstall (flashes stock.zip and replaces mbr with stock mbr)
reboot into recovery
restore nandroid image.
This has yet to fail me and usually takes under 10 minutes. The nandroid image is key. Most of the time, I can skip the Odin step completely if I am not seeing anything truly, staggeringly horrific going on.
Again, jt's voodoo-uninstall seems to solve a lot more than just voodoo issues. This thing should get it's own topic/forum/entry in ROM Manager/zip code/nobel award...you get the picture.
PhoenixPath said:
Again, jt's voodoo-uninstall seems to solve a lot more than just voodoo issues. This thing should get it's own topic/forum/entry in ROM Manager/zip code/nobel award...you get the picture.
Click to expand...
Click to collapse
+1 I agree
Nice write up! I'm sure this will help many people.
Thanks
This along with several other threads allowed me to recover from my own mental retardation.
Gotta remember to remove voodoo before doing stuff. I should know better.
Thanks again.
This is not working for me. I removed voodoo (using the uninstaller). I then did odin and my phone boots but I cant do anything past the unlock bc of all the fcs I get. I wiped the cache and data. CWM is not working, when I try to do the update.zip I get a "failed to verify whole-file signiture". - I deleted the voodoo folder from the sd-card after uninstalling voodoo, dont know if that contributed to the problem. Any ideas?
Ke1evraTi said:
This is not working for me. I removed voodoo (using the uninstaller). I then did odin and my phone boots but I cant do anything past the unlock bc of all the fcs I get. I wiped the cache and data. CWM is not working, when I try to do the update.zip I get a "failed to verify whole-file signiture". - I deleted the voodoo folder from the sd-card after uninstalling voodoo, dont know if that contributed to the problem. Any ideas?
Click to expand...
Click to collapse
Sounds like you need to re-flash ClockworkMod through Odin. I'm guessing it got wiped out when you went back to stock.

Hmm. No boot.

Well well. I know it may surprise you to see me here
I was messing with busybox, trying to update it. Apparently I did something wrong and the phone doesn't boot now. It'll go on the bootanimation, but at the very end, JUST before the menu softkeys lights come up, it instantly crashes and returns to the splash screen and the cycle is repeated.
Anything I can do to restore it back to an usable state, without losing the data I have on the phone? I know how to make it work again, that's really easy, but what I don't know how, is to make it work again without losing data.
I mean, busybox update seemed safe enough >_> Then it broke everything else.
Oh well, any answers would be appreciated.
Just a thought, no expert here but I've made changes to my phone tht caused me to get stuck and I've gone into recovery-restore-advanced restore and just restored the system part and its gotten me back to a running state.
I'm also thinking if you make a nandroid of your current state then try and fix the issue at least you can always have tht to go back to if someone gets you a better answer.
Wish you the best of luck, I hate having to wipe too!
I was born in Darkness.....
chozyn said:
Just a thought, no expert here but I've made changes to my phone tht caused me to get stuck and I've gone into recovery-restore-advanced restore and just restored the system part and its gotten me back to a running state.
I'm also thinking if you make a nandroid of your current state then try and fix the issue at least you can always have tht to go back to if someone gets you a better answer.
Wish you the best of luck, I hate having to wipe too!
I was born in Darkness.....
Click to expand...
Click to collapse
Didn't work, but it was a good idea actually. I didn't have a recent backup. Didn't make one, as I thought busybox would be easy enough and wouldn't affect much. Oops.
Man, I'm having such bad luck today... First, I accidentally deleted few gigs of stuff off my computer. Then my phone gets messed up due to something I did in busybox. Gee, what's next?
Damn....going out on a limb here but what if you back up your rom in its current not booting state. Then wipe and do a fresh install of the same Rom-backup the fresh install.
Afterwards flash the not booting backup you made and then do the advanced restore using the system IMG from the fresh install to see if it will boot?
Sorry thinking in layman's terms here.
I was born in Darkness.....
Flash the Rom over your brick it should boot back up. Busy box writes the files in /system/xbin (If I remember) so when you reflash the Rom you're using it writes everything back to normal. Just don't do a wipe and you should be good.
Anything that was changed in /system will be reset to original.. so if you had GNow it'll have to be reinstalled. Same thing with any other files in /system.
chozyn said:
Damn....going out on a limb here but what if you back up your rom in its current not booting state. Then wipe and do a fresh install of the same Rom-backup the fresh install.
Afterwards flash the not booting backup you made and then do the advanced restore using the system IMG from the fresh install to see if it will boot?
Sorry thinking in layman's terms here.
I was born in Darkness.....
Click to expand...
Click to collapse
I actually thought of this, but for some reason, it doesn't work. It still gets hard bootloops.
Double0EK said:
Flash the Rom over your brick it should boot back up. Busy box writes the files in /system/xbin (If I remember) so when you reflash the Rom you're using it writes everything back to normal. Just don't do a wipe and you should be good.
Anything that was changed in /system will be reset to original.. so if you had GNow it'll have to be reinstalled. Same thing with any other files in /system.
Click to expand...
Click to collapse
Thought of this before I did anything, but apparently it affected the /data too (The files inside there are intact, but something there is not allowing my phone to boot), thus continuing the hard bootloops.
I'm befuddled. I will have to figure this out later. For now, I just made a backup of the non-working ROM and wiped everything and flashed a ROM on it. I'll figure out what parts of /data to transfer back later. I needed a functioning phone, so yeah
Thanks for the help. If anyone else has any other good ideas, I'll try them out.
Keylogger_0 said:
I actually thought of this, but for some reason, it doesn't work. It still gets hard bootloops.
Thought of this before I did anything, but apparently it affected the /data too (The files inside there are intact, but something there is not allowing my phone to boot), thus continuing the hard bootloops.
I'm befuddled. I will have to figure this out later. For now, I just made a backup of the non-working ROM and wiped everything and flashed a ROM on it. I'll figure out what parts of /data to transfer back later. I needed a functioning phone, so yeah
Thanks for the help. If anyone else has any other good ideas, I'll try them out.
Click to expand...
Click to collapse
What rom are you using?
Grab that rom, in a zip file preferably, modify the updater script to not write to the data partition, wipe all partitions except data, flash and reboot.
Fix permissions and wipe caches if needed.

[Q] Help Getting A Working Rom after Bootloader Unlock

Hi all,
I have a Droid incredible 4g (stock, unrooted/unlocked, w/ the recent OTA update). I saw the Bootloader Unlock exploit in the developer's forum so I gave it a go, and it worked fine. Then I installed the Viper 1.0 ROM, but I haven't been able to get it to do anything after successfully booting except run through a loop of errors such as "Unfortunately, the process android.process.acore has stopped working." After I click "OK" on about 10 critical errors, it self-reboots and does the whole thing again.
Unfortunately, I didn't do a backup this time, so I have nothing to restore (first time I haven't done a backup, but also the first time I've ever had any kind of an issue w/ a ROM). I tried using the HTC Android ROM Update Utility 1.0.5.2011 that I found in the dev forum, but that didn't work either. Finally, I installed 2.17.605.2 Verizon Global Sense4.1 Android 4.0.4. It's a lot more stable than Viper was and the phone is basically usable, but I still get lots of critical errors. So this morning I went back to the forum and saw that I needed to downgrade to the old 1.43.605.3 kernel. I tried that and then reinstalled Viper 1.0, but it seemed to have no effect--still stuck in a critical error/reboot loop.
I realize that's the risk of playing with ROMs and I should have done a backup, but anyone have any ideas on how I can get my phone back and running?
Thanks!
Even though it explicitly stated you didn't need to do a backup, I did one anyway, to prevent something like this from happening. Always do a backup.
Did you verify the MD5Sum of ViperLTE?
Did you go to Recovery and Wipe -> Factory Reset and Wipe -> System both twice before trying to install the ROM?
Did you change anything in the ROM before attempting to load it?
There are lots of questions we could ask to ascertain the root of the problem, but these three are among the most important.
Wi-Fi won't work without the old boot.img, and from what I can tell, that's the only thing. It doesn't give critical errors.
I'm thinking since you are new to root you were un-aware the need to wipe before installing a rom.
im thinking that is the issue.
Thanks for the reply!
I didn't check the MD5 last night but I did just now and it matches.
I did a cache wipe the first time but not a system wipe. Then I started getting more desperate and tried reinstalling w/ system wipes and factory resets, but it didn't change anything.
No, I didn't change the ROM. Doing the Bootloader unlock exploit was about the absolute maximum of my technical abilities! The only thing I know I did wrong was that I didn't downgrade to the old boot version the first time (mainly because the wifi thing sounded inconsequential and I didn't want to learn the procedure if I didn't have to).
Anyway, I just tried Ultimate KangBang and it seems to work--no error messages so far. I don't know what I did wrong, but hopefully this keeps working!
IceDragon59 said:
Even though it explicitly stated you didn't need to do a backup, I did one anyway, to prevent something like this from happening. Always do a backup.
Did you verify the MD5Sum of ViperLTE?
Did you go to Recovery and Wipe -> Factory Reset and Wipe -> System both twice before trying to install the ROM?
Did you change anything in the ROM before attempting to load it?
There are lots of questions we could ask to ascertain the root of the problem, but these three are among the most important.
Wi-Fi won't work without the old boot.img, and from what I can tell, that's the only thing. It doesn't give critical errors.
Click to expand...
Click to collapse
andybones said:
I'm thinking since you are new to root you were un-aware the need to wipe before installing a rom.
im thinking that is the issue.
Click to expand...
Click to collapse
Yes, I took a short-cut that didn't quite work out. I didn't want to wipe the system because I wasn't sure if my pictures would be wiped too, but then when everything died I tried wiping everything and reinstalling and it didn't seem to improve anything. I did end up losing my pictures too. Oh well. Maybe it's just a combination of stuff I did to try to get things working (there was some trial and error in unlocking the bootloader but I did get that to work finally, and then more trial and error with the ROMs).
I guess the best thing to do is leave the phone the heck alone as long as it's working, for now. I just don't know why nothing seemed to work--I thought factory reset/fresh ROM would do it.
franklin411 said:
Yes, I took a short-cut that didn't quite work out. I didn't want to wipe the system because I wasn't sure if my pictures would be wiped too, but then when everything died I tried wiping everything and reinstalling and it didn't seem to improve anything. I did end up losing my pictures too. Oh well. Maybe it's just a combination of stuff I did to try to get things working (there was some trial and error in unlocking the bootloader but I did get that to work finally, and then more trial and error with the ROMs).
I guess the best thing to do is leave the phone the heck alone as long as it's working, for now. I just don't know why nothing seemed to work--I thought factory reset/fresh ROM would do it.
Click to expand...
Click to collapse
If UKB ROM works then Viper ROM will too, installing the boot.img is very simple it's one command
I can help you with that if you'd like
in recovery before installing ROM, do a wipe of, (I go in this order, but it doesn't matter.)
1) Factory Reset
2) System
3) Cache
4) Dalvik Cache
then install the ROM
just DO NOT do External storage (unless of coarse u WANT to wipe your SD-Card.)
as long as you don't wipe External Storage you won't lose anything that's on your SD-Card.
in the future it is always good practice to backup(nandroid) your current ROM. I have been burned too many times, always do a nandroid before you do anything in recovery.
your photos are normally saved to the SD, flashing ROMs or wiping the system will not delete them
andybones said:
If UKB ROM works then Viper ROM will too, installing the boot.img is very simple it's one command
I can help you with that if you'd like
in recovery before installing ROM, do a wipe of, (I go in this order, but it doesn't matter.)
1) Factory Reset
2) System
3) Cache
4) Dalvik Cache
then install the ROM
just DO NOT do External storage (unless of coarse u WANT to wipe your SD-Card.)
as long as you don't wipe External Storage you won't lose anything that's on your SD-Card.
Click to expand...
Click to collapse
It worked this time! Maybe the difference was that the boot.img file I downloaded was called "boot_signed.img" or something. I had no idea what it was supposed to look like, so I installed it that way and it didn't work. Then I tried renaming it to "boot.img" this morning and installing viper, but that didn't work. And then I restarted and installed UKB, and it worked. Just now I wiped and tried again with Viper and it's working fine. Maybe I did something this morning that caused it not to take properly when I tried with Viper, and then I reset and it worked.
Thanks for the help!
franklin411 said:
It worked this time! Maybe the difference was that the boot.img file I downloaded was called "boot_signed.img" or something. I had no idea what it was supposed to look like, so I installed it that way and it didn't work. Then I tried renaming it to "boot.img" this morning and installing viper, but that didn't work. And then I restarted and installed UKB, and it worked. Just now I wiped and tried again with Viper and it's working fine. Maybe I did something this morning that caused it not to take properly when I tried with Viper, and then I reset and it worked.
Thanks for the help!
Click to expand...
Click to collapse
na the name has nothing to do with it. it can be named whatever.
im guessing the wipe worked.
franklin411 said:
Hi all,
I have a Droid incredible 4g (stock, unrooted/unlocked, w/ the recent OTA update). I saw the Bootloader Unlock exploit in the developer's forum so I gave it a go, and it worked fine. Then I installed the Viper 1.0 ROM, but I haven't been able to get it to do anything after successfully booting except run through a loop of errors such as "Unfortunately, the process android.process.acore has stopped working." After I click "OK" on about 10 critical errors, it self-reboots and does the whole thing again.
Unfortunately, I didn't do a backup this time, so I have nothing to restore (first time I haven't done a backup, but also the first time I've ever had any kind of an issue w/ a ROM). I tried using the HTC Android ROM Update Utility 1.0.5.2011 that I found in the dev forum, but that didn't work either. Finally, I installed 2.17.605.2 Verizon Global Sense4.1 Android 4.0.4. It's a lot more stable than Viper was and the phone is basically usable, but I still get lots of critical errors. So this morning I went back to the forum and saw that I needed to downgrade to the old 1.43.605.3 kernel. I tried that and then reinstalled Viper 1.0, but it seemed to have no effect--still stuck in a critical error/reboot loop.
I realize that's the risk of playing with ROMs and I should have done a backup, but anyone have any ideas on how I can get my phone back and running?
Thanks!
Click to expand...
Click to collapse
weird, i was having the same problem with the same processes stopped working. i wiped cache dalvik and system but not factory reset. once i factory reset, it worked fine. i figured a system wipe would have been enough....

[Q] Custom roms - I might have messed something up

I only recently got into the whole rooting deal, but i followed the instructions precisely double checking and everything went along well , after that i installed most of the apps from here, made a full backup with titianium backup, but then i decided to try and install a custom rom, which was where i made my first mistake, i made a backup of the current(stock) rom and then went straight on to downloading cyagenmod 7.2 to try it out on my phone.
When i started the install i obviously had the pre install options, i only left the one check there which was wipe delvik cache i think figuring that was all i needed to do. Phone rebooted and the loading logo started but didnt go past it and after it had reappeared for 3 times the screen just went in a white screen with differently colored horizontal stripes, i thought my phone was now bricked, but i managed to turn it off and turn it back on and get into recovery mode. I tried to do a recovery which didnt do anything, after that i just selected factory reset thinking it will get me back to the stock rom, but instead CM worked and finally got past the loading logo, i checked in the CWM if i had the backup i had made before trying to install CM and it was gone.
I want to know what i have done wrong(i obviously have), how can i reverse it and how to install roms properly(preferably in simple language). I already found this thread.
Phone: LG Optimus Hub (E-510)
P.S. I am missing the Play store app, is this normal for CM?
1. You got into bootloop because you didn't do factory reset/full wipe (the /data partition wasn't wiped, files on this partition were from stock ROM and weren't compatible with CM) -> this is the reason why it booted after full wipe. Full wipe only deletes data, it will not restore stock ROM.
2. '... i checked in the CWM if i had the backup i had made before trying to install CM and it was gone'
Are you sure you made a backup? Or didn't you delete it?
3. For the Play store - CM ROMs ussually don't have Google Apps in them, you have to flash them after CM installation (look in the ROMs thread for Google apps/ GApps)
1. Thanks for the explanation, im defineatly going to keep in mind to wipe the next time i attempt to install a custom rom. Is the stock rom still in my phone or do i have to look online for one?
2. I belive you are right, i do remember wanting to do a backup, but i might have forgotten about it, i did one now so i can have something to go back to just in case.
3. Dont really understand this, can you please direct me to a thread for this? I tried doing the flash CWM recovery which didnt do anything, could i try using my backups from titanium backup to get the apps back on the phone? It would be quite a mess to get all of it downloaded again.
Edit: i tried installing google play downloaded from other sites and whenever i go into it, it asks me to add an account, but when i press yes, it just closes.
|Madman| said:
1. Thanks for the explanation, im defineatly going to keep in mind to wipe the next time i attempt to install a custom rom. Is the stock rom still in my phone or do i have to look online for one?
2. I belive you are right, i do remember wanting to do a backup, but i might have forgotten about it, i did one now so i can have something to go back to just in case.
3. Dont really understand this, can you please direct me to a thread for this? I tried doing the flash CWM recovery which didnt do anything, could i try using my backups from titanium backup to get the apps back on the phone? It would be quite a mess to get all of it downloaded again.
Edit: i tried installing google play downloaded from other sites and whenever i go into it, it asks me to add an account, but when i press yes, it just closes.
Click to expand...
Click to collapse
First things first. Before you do anything else you need to do some reading in order to understand the Basics of Android. Otherwise your going to get yourself in a bind again. In my Signature your going to see some links if your on a PC. You should check them out, they will help with answers to a lot of your questions.
I cant thank you enough, i was looking for something like this! :good:
I will have something to read in my spare time, as little of it i have trough.
Your welcome . Glad I could help.
TEAM MiK
MikROMs Since 3/13/11

stuck on cyangenmod logo

So I have had Cyangenmod 10 installed for several months now and it's been working fine until I would say the last 2 weeks. Now, sometimes it will lock up or slow down and when I restart it, it will get stuck on the cyangenmod logo and never fully boot. After several restarts, I can sometimes get in and all is fine. But today, I have rebooted the Nook Tablet about 10 times now and the Cyangenmod logo will spin for a bit, then stop and then spin and then stop, etc but I can never get in
Ideally, I don't want to restore as I have a number of things on the Tablet that I want to keep. Any suggestions before going that route?
Try going into recovery and wiping cache and dalvik-cache, and then reboot. When oddball things happen, this should be your first trouble shooting step.
Good luck
Sent with my Dinc4G
tried the wipes and still gets stuck on the cyangenmod logo..just spins and stops for a bit, then spins some more
any other ideas
Titanium backup the apps/data you want to keep then full wipe - data/factory reset.
Sent with my Dinc4G
can't do titanium backup if I cant even get passed the cyangenmod logo
Ya good point.
You may have to reflash the rom (or another rom) after a full wipe. I know you are trying to avoid this, but you may not have a choice. You should, however be able to restore your data through advance restore in recovery (make sure you do a backup first though). And it is possible something you put on your nt is causing this - not likely but possible.
Had you done any mods or such on you nt prior to this?
Edit - Another thought too, try flashing the latest update of cm10.1, Just wipe cache and dalvik cache. Flash over the top your current build.
Good luck
Sent with my Dinc4G

Categories

Resources