Hey guys, immediately after flashing NRG's energy rom, I am now getting edge network coverage (3g) in all the places i was getting 2g coverage. I didn't see this mentioned in the energy rom thread, so I wanted to say thanks. (I cant exactly attribute this to flashing the rom, as the carrier may have increased coverage, but it is doubtful that they did.)
It's the same radio band... No s=off means no radio flashing. That means, although Energy ROM is AWESOME, it probably didn't increase your cell reception.
Sent from my HTC_Amaze_4G using xda premium
I myself have experienced better coverage as well. but what i think happened was that the radio signal to pick up for 4g service was lowered like ex. if it required 70db to pick up 4g signal it was probably lowered to 65 db hence areas with less coverage well be covered but with really really weak service. but i would like to be wrong and someone correct me so i learn more
im not too familiar with radio flashing although the amaze comes with edge and now im getting edge coverage in a county that I was only receiving 2g coverage. My girlfriend was getting edge coverage on her t mobile phone in the same locations that i was getting 2g, until i flashed energy rom.
IfYouAintFirstYoureLast said:
im not too familiar with radio flashing although the amaze comes with edge and now im getting edge coverage in a county that I was only receiving 2g coverage. My girlfriend was getting edge coverage on her t mobile phone in the same locations that i was getting 2g, until i flashed energy rom.
Click to expand...
Click to collapse
Me either... Maybe I'm wrong too, idk... I'm no dev, just an experienced instruction follower
Sent from my HTC_Amaze_4G using Tapatalk 2 Beta-2
IfYouAintFirstYoureLast said:
im not too familiar with radio flashing although the amaze comes with edge and now im getting edge coverage in a county that I was only receiving 2g coverage. My girlfriend was getting edge coverage on her t mobile phone in the same locations that i was getting 2g, until i flashed energy rom.
Click to expand...
Click to collapse
Edge IS 2g. They're both the same.
this...
glacierguy said:
It's the same radio band... No s=off means no radio flashing. That means, although Energy ROM is AWESOME, it probably didn't increase your cell reception.
Sent from my HTC_Amaze_4G using xda premium
Click to expand...
Click to collapse
and this...
Keylogger_0 said:
Edge IS 2g. They're both the same.
Click to expand...
Click to collapse
also, just because it says your signal is better, doesnt mean it actually is
Related
So was at the mall yesterday with a friend, she has an inspire on at&t i went to download a new game on my phone from the market the game was 20mb i was downloading it for like 20 mins and she downloaded it in like 2mins i was like wtf... Why is the sprint network so so slow? I was doing speed tests with almost full signal and was getting like 70kb
Sent from my PG86100 using Tapatalk
At&t has the fastest network, but they charge crazy amounts for overages.
Sent from my PG86100 using XDA App
Coverage differ eveywhere, speed is affect by tower load and backhaul, more users per tower, slower you get, so probably the sprint tower was serving more customer than ATT?
ATT 3G (which is also their psuedo 4G) is faster than sprint's 3G base on the technology, HSDPA vs CMDA/EVDO
i bet you weren't using the 4G right? if you can get a decent 4G signal then the speed should be comparable, but being inside a mall, unless the mall is right next to the tower.... hard to get a decent signal
akiradavis said:
At&t has the fastest network, but they charge crazy amounts for overages.
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
VZW 4G is fastest, even faster than ATT HSDPA
I thought I saw Verizon scoring the highest.. but you maybe right.
I wasnt on 4g just 3g, me and her both were outside the mall when downloading, so ur saying her 3g is actually 4g?
Sent from my PG86100 using Tapatalk
From what I understand ATT has the fastest speed if and when you can get a slot on the tower--they are much better at this part than they were a year ago.
Verizon has middle of the road speed and expansive coverage.
Sprint has decent enough coverage and good roaming agreements, not over-saturated towers and WAS considerably faster than Verizon--until the EVO4G came out last year. I could actually notice my speeds dropping from day to day. They bottomed out 4 or 5 months ago and are stuck where they are...
Keep in mind this also changes based on time of day and population density and your data speed will be proportionate to your signal strength for the most part. If your buddy with ATT had full bars and you had almost none it doesn't matter whose phone or network is the fastest. Though I hear CDMA and GSM handle this differently I'm not so sure about that.
Even though with only 1/4 bar on my NS4G I get 1.5mbps in my apartment...the E3D went back primarily cuz its radios sucked for stability and performance. Hell, on my E4G I traded in yesterday I got 2.1mbps with 3/6 bars. The E3D couldn't touch that.
cody_cummins said:
I wasnt on 4g just 3g, me and her both were outside the mall when downloading, so ur saying her 3g is actually 4g?
Sent from my PG86100 using Tapatalk
Click to expand...
Click to collapse
You likely weren't even on 3g, probably down to 1x, stock software wont show the difference though. Sprint's network blows in most places but I have faith that it'll get better.
I say stick with Sprint, they are adopting new technologies quicker than verizon and at&t. But speaking of 3g speed, at&t has the fastest but spotty coverage, then comes verizon with fast speed, excellent coverage, and t-mobile and sprint tied for third with ok speed and coverage. But I hear t-mobile's 3g speeds have been getting better with their introduction of 4g.
All in all, hopefully by 2012, sprint's standard 3g speeds will be better
Sent from my PG86100 using XDA App
cody_cummins said:
I wasnt on 4g just 3g, me and her both were outside the mall when downloading, so ur saying her 3g is actually 4g?
Sent from my PG86100 using Tapatalk
Click to expand...
Click to collapse
for NOW, what AT&T call is 4G is actually faster version of their 3G tech same as Tmobile, which is HSPA+, AT&T won't BEGIN roll out their actual 4G LTE network until LATE this year.
Notice 4G LTE is the Tech Verizon have ALREADY deployed.
Early test with the not yet congested VZW 4G LTE show ACTUAL speeds download AND UPLOAD upward of 20mbps
AT&T's HSPA+ is MAX 14mbps, most day to day use see speed between 3-10mbps.
Tmo's HSPA+ is MAX 42mbps, most day to day use see speed about 10mbps.
Sprint and VZW's 3G is EVDO, that MAX out in day to day use about 2mbps, VZW on average is faster than Sprint, maybe about 200kbps-300kbps difference.
Sprint's 4G is WiMax, fastest i've seen is about 12mbps, usually more like 3-6mbps. so to have a chance to catch your friend's AT&T's speed, you need to have 4G on.
drawback of 4G Wimax and LTE... current generation chips suck battery juice super quick, our EVO 3D can be drain in 3-5hours of 4G usage
Pro of 4G Wimax and LTE, alot more spectrum/frequency efficient on the carrier's side, they can have more capacity in the same spectrum. Note that this is a mostly a Pro for the carrier and mostly a NULL factor to end users.
vice versa a CON of ATT/Tmo HSPA+ 3G/Psuedo 4G... they need more spectrum/frequency to acheive same capacity as 4G Wimax/LTE
Just the point that the signal with my 3d really sucks where ever i go, i dont know if its a hardware issue or a software issue, i dont wanna be stuck with a phone that gets horrible signal all the time, so should i take it back or keep it and hoping an update fixes the radios?
Sent from my PG86100 using Tapatalk
cody_cummins said:
Just the point that the signal with my 3d really sucks where ever i go, i dont know if its a hardware issue or a software issue, i dont wanna be stuck with a phone that gets horrible signal all the time, so should i take it back or keep it and hoping an update fixes the radios?
Sent from my PG86100 using Tapatalk
Click to expand...
Click to collapse
I'm with ya man. I did both. If this gets fixed (and we get unlocked) I'll be back. But until then I'm rocking a NexusS4G with a crappy Samsung radio that is somehow more reliable than the 3D's radio--just sayin'.
It has everything to do with where you are. I am in Miami/South Miami/Coconut Grove, FL and Sprint dominates ATT and Verizon. The blackberry bold I have on Verizon from work is essentially worthless in a shocking amount of popular/urban places. The Droid X I had before the bb was equally as bad. It is so bad I have to shell out my own money for a sprint phone to get decent service.
I always figured Verizon had blanket coverage everywhere since they market it so well but their coverage where I am is really poor. Of course if you call them, they act shocked and reference their map that shows dense coverage.
Sent from my PG86100 using XDA Premium App
Well what do yall think of the radio issue, will it be fixed with a software update or should i return it? Because im going from 5 bars one second to one or none the next, need some help here
Sent from my PG86100 using Tapatalk
bitslizer said:
Coverage differ eveywhere, speed is affect by tower load and backhaul, more users per tower, slower you get, so probably the sprint tower was serving more customer than ATT?
ATT 3G (which is also their psuedo 4G) is faster than sprint's 3G base on the technology, HSDPA vs CMDA/EVDO
i bet you weren't using the 4G right? if you can get a decent 4G signal then the speed should be comparable, but being inside a mall, unless the mall is right next to the tower.... hard to get a decent signal
Click to expand...
Click to collapse
Its sad that AT&T's 3.5G HSDPA is faster than Wimax. I have a company AT&T phone and it's way faster than my Evo.
AT&T is more expensive but I'm still attached to my OG Evo. Hopefully Sprint catches up.
Sent from my PC36100 using XDA App
gqstatus0685 said:
Hopefully Sprint catches up.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
Welcome to Sprint! I see you've already learned their motto..
I don't know what's up with this phones reception or data speeds. It Sux! I mean for phone reception, I get 2 less bars everywhere I go and for data I'm getting barley .5 mb when used to always get about .9 with og EVO.
Besides these issues the phone is top notch. I'm still have a couple of weeks to take it back, but I really don't want to. Hopefully these issues can be worked out soon.
Sent from my PG86100 using XDA App
blues2009 said:
I don't know what's up with this phones reception or data speeds. It Sux! I mean for phone reception, I get 2 less bars everywhere I go and for data I'm getting barley .5 mb when used to always get about .9 with og EVO.
Besides these issues the phone is top notch. I'm still have a couple of weeks to take it back, but I really don't want to. Hopefully these issues can be worked out soon.
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
I totally agree with you, if they dont fix the reception issues and data speeds im gonna have to take this thing back, not because i want to but im not gonna tolerate 1 bar at my house where i should be getting full and 50kb data speeds which is absolutely pathetic, they need to release an update to fix this issue right away, htc has really upset me with this phone
Sent from my PG86100 using Tapatalk
daneurysm said:
Welcome to Sprint! I see you've already learned their motto..
Click to expand...
Click to collapse
"Welcome to Sprint, the not right NOW network."
I had a bad signal too, changed the PRL in QPST to a USCellular (15110) and have great coverage ever since When I called Sprint for my MSL, I told the tech that I was planning on changing the PRL due to a bad signal, he said "that's a great idea"
Sent from my PG86100 using XDA Premium App
A small observation i have made thus far with running code's Kang
There seems to be alot of bouncing between 3G and H+. Im not sure what the implications are in terms of bat drain or issues, however just somthing i have observed that i do not running a similar OS on my Desire HD.
My area we are not yet H+ however i hold steady at h+ most all the time.
Drew
All 4G phones have H+ constant unless they fall on EDGE
Sent from my SAMSUNG-SGH-I777 using xda premium
ngocdao said:
All 4G phones have H+ constant unless they fall on EDGE
Sent from my SAMSUNG-SGH-I777 using xda premium
Click to expand...
Click to collapse
I understand this, however its bouncing between H+ and 3G constandly like once ever other min, which seems odd
Drew
drewdatrip said:
I understand this, however its bouncing between H+ and 3G constandly like once ever other min, which seems odd
Drew
Click to expand...
Click to collapse
I know devices typically switch if something is actively going on (an active data session). Are your data transmission arrows lighting up when showing H and nothing when showing 3G? If so, I think this is typical.
ngocdao said:
All 4G phones have H+ constant unless they fall on EDGE
Sent from my SAMSUNG-SGH-I777 using xda premium
Click to expand...
Click to collapse
Wrong. Phones only use HSPA when transferring data, they idle in vanilla UMTS.
AT&T mangles their frameworks to report everything as H+ even when it's not actually in HSDPA+ mode.
CM7 is just reporting the truth that AT&T's mangled framework hides from you.
Entropy512 said:
Wrong. Phones only use HSPA when transferring data, they idle in vanilla UMTS.
AT&T mangles their frameworks to report everything as H+ even when it's not actually in HSDPA+ mode.
CM7 is just reporting the truth that AT&T's mangled framework hides from you.
Click to expand...
Click to collapse
Its bouncing both in and outside of data consumption. I dont find this to be the case Running CM7 or MIUI on my Desire HD
Just an observation
Drew
Different RIL.
And our RIL might have the same minor issue that the Infuse RIL did in which HSPA+ was reported as only UMTS - so if you were in a non-+ HSPA mode it would be H, if you were in 3G it would be 3G, if you were in HSPA+ it would be 3G. This was a display error... Do you notice any significant differences in actual data speed performance between CM7 and stock firmware?
(Actually, you could still see slow data if the CM7 tree uses older TCP buffer size values.)
Hello DInc 4G community,
I was curious to know if anyone else has seen low call signal or 4G signal loss with JB based ROMs? I have tried CM10.1 and the Avatar ROM and when flashing either, the cell signal strength only show's up to 3 bars as well as my phone always reverting to 3G instead of 4G. If I go back to stock based ROM, my cell signal shows full bars as well as the data mostly in 4G mode. Not sure it this is an artifact of the status bar indicator icon or possible firmware related? When I had my Dinc2 and was using ICS based ROM's, I had noticed improvements when flashing the ICS firmware.Wondered if this was the same for the DInc4g LTE?
rudyo78427 said:
Hello DInc 4G community,
I was curious to know if anyone else has seen low call signal or 4G signal loss with JB based ROMs? I have tried CM10.1 and the Avatar ROM and when flashing either, the cell signal strength only show's up to 3 bars as well as my phone always reverting to 3G instead of 4G. If I go back to stock based ROM, my cell signal shows full bars as well as the data mostly in 4G mode. Not sure it this is an artifact of the status bar indicator icon or possible firmware related? When I had my Dinc2 and was using ICS based ROM's, I had noticed improvements when flashing the ICS firmware.Wondered if this was the same for the DInc4g LTE?
Click to expand...
Click to collapse
that's kind of miss leading, if you check the numbers on your signal on both roms they are about the same. the number of bars is just different, as for the 3g and 4g stuff i'm not sure, never checked the numbers
I've seen the same thing, not looking at bars, but dbm
As in lower signal, more loss of reception on jb
Patgt500 said:
I've seen the same thing, not looking at bars, but dbm
As in lower signal, more loss of reception on jb
Click to expand...
Click to collapse
Yeah...forgot to mention that. At home with a stock ROM or even debloated stock ROM I get -79 to -90 dBm (4 -5 full bar icon). When I was using CM10.1 based ROM's I was seeing -89 to -101 dBm range (2-3 bar icon). So I'm staying with the PizzutoClaws ROM as my daily driver
rudyo78427 said:
Yeah...forgot to mention that. At home with a stock ROM or even debloated stock ROM I get -79 to -90 dBm (4 -5 full bar icon). When I was using CM10.1 based ROM's I was seeing -89 to -101 dBm range (2-3 bar icon). So I'm staying with the PizzutoClaws ROM as my daily driver
Click to expand...
Click to collapse
well when you get -79 to -90 are you on cdma or lte, there's a difference. when i'm on cdma on cm10 i get -75 when on lte i get -90 to -101
Aldo101t said:
well when you get -79 to -90 are you on cdma or lte, there's a difference. when i'm on cdma on cm10 i get -75 when on lte i get -90 to -101
Click to expand...
Click to collapse
My lower values I posted are on LTE. The lower the - dBm / dB value the better or closer you are to the Tower. As my signal gets worse 1-2 bar graph, I'm at -118 to -120 dBm on 4G. When my phone switches to 3G/EVDO/1x the signal strength is only showing dB value.
My 4G doesn't work at all on CM10.1. Just a hint on how to avoid this... Never mess with radio settings or try updating roaming capabilities. CyangenMod will break your 4G. There are problems with CyangenMod and device radios. There needs to be a way to reprogram the Radio Bands. Someone please try and figure something out. I have figured out a way on how to manipulate the radio to connect to 4G. But it is kinda complicated. You have have to switch the CDMA Subscription from RUIM/SIM to NV, then go to the dialer and dial *#*#4636#*#* then go into Phone Information, then go to "Set preferred network type:" and make sure that it says: "LTE/CDMA auto (PRL)" then restart your phone. There are a couple downsides to this.
1) Your calling won't work.
2) Your messaging won't work.
--
The only good thing about this is faster internet than 3G. About 1 MBps. (Roughly)
That is one thing I discovered while trying to repair my 4G. Good luck and if you figure it out, there is a forum that is called 4G Not Working that needs a solution to this specific problem. Please share it.
Sent from my Incredible 4G LTE using xda app-developers app
vazersecurity said:
My 4G doesn't work at all on CM10.1. Just a hint on how to avoid this... Never mess with radio settings or try updating roaming capabilities. CyangenMod will break your 4G. There are problems with CyangenMod and device radios. There needs to be a way to reprogram the Radio Bands. Someone please try and figure something out. I have figured out a way on how to manipulate the radio to connect to 4G. But it is kinda complicated. You have have to switch the CDMA Subscription from RUIM/SIM to NV, then go to the dialer and dial *#*#4636#*#* then go into Phone Information, then go to "Set preferred network type:" and make sure that it says: "LTE/CDMA auto (PRL)" then restart your phone. There are a couple downsides to this.
1) Your calling won't work.
2) Your messaging won't work.
--
The only good thing about this is faster internet than 3G. About 1 MBps. (Roughly)
That is one thing I discovered while trying to repair my 4G. Good luck and if you figure it out, there is a forum that is called 4G Not Working that needs a solution to this specific problem. Please share it.
Sent from my Incredible 4G LTE using xda app-developers app
Click to expand...
Click to collapse
if you would read the OP IN DEVELOPMENT you could solve these problems, concerning cm10.1 md has made it quite clear there
Aldo101t said:
if you would read the OP IN DEVELOPMENT you could solve these problems, concerning cm10.1 md has made it quite clear there
Click to expand...
Click to collapse
Yeah I have checked that, I attempted his fix method but no go.
vazersecurity said:
Yeah I have checked that, I attempted his fix method but no go.
Click to expand...
Click to collapse
This is a worthless response. What does "no go" mean? Be descriptive of what you tried, and in the process what worked and what failed.
Yeah I know not to talk to you because you're kinda a jerk. I just talked to Verizon and got it sorted out with them. I now have working 4G. But remove the *228 feature in your ROM, because that's what the problem was. It messed up my SIM Card because I wasn't aware you weren't supposed to do *228 on a phone like this. You developers are just too serious. Need to lighten up a little bit to the developers that haven't really got that much experience.
Sent from my ADR6410LVW using xda app-developers app
vazersecurity said:
Yeah I know not to talk to you because you're kinda a jerk. I just talked to Verizon and got it sorted out with them. I now have working 4G. But remove the *228 feature in your ROM, because that's what the problem was. It messed up my SIM Card because I wasn't aware you weren't supposed to do *228 on a phone like this. You developers are just too serious. Need to lighten up a little bit to the developers that haven't really got that much experience.
Sent from my ADR6410LVW using xda app-developers app
Click to expand...
Click to collapse
So...you weren't aware you weren't supposed to do *228? So you messed up? And you blame the developer? The guy making everyone's phone better. Moron.
Sent from my Incredible 4G LTE using xda app-developers app
somerandomname1 said:
So...you weren't aware you weren't supposed to do *228? So you messed up? And you blame the developer? The guy making everyone's phone better. Moron.
Sent from my Incredible 4G LTE using xda app-developers app
Click to expand...
Click to collapse
+1
Not blaming the developer. Just how he treated me. I did mess up. Sorry about that.
Sent from my ADR6410LVW using xda app-developers app
vazersecurity said:
Not blaming the developer. Just how he treated me. I did mess up. Sorry about that.
Sent from my ADR6410LVW using xda app-developers app
Click to expand...
Click to collapse
Asking for more information so he might be able to identify your problem is a huge jerk move. Now I understand....
Don't try to learn something if you can't take constructive criticism. It's natural to be frustrated when you're very experienced with something and someone asks for help with few details. Dumb questions get dumb answers.
Sent from my Incredible 4G LTE using xda app-developers app
somerandomname1 said:
Asking for more information so he might be able to identify your problem is a huge jerk move. Now I understand....
Don't try to learn something if you can't take constructive criticism. It's natural to be frustrated when you're very experienced with something and someone asks for help with few details. Dumb questions get dumb answers.
Sent from my Incredible 4G LTE using xda app-developers app
Click to expand...
Click to collapse
Yeah, I'm just a little sensitive, need to work on that myself. But this site isn't for talking about that. haha.
Apparently some people are having signal issues (i.e., dropping between HSPA and LTE where other AT&T phones are rock solid LTE) with the Developer Edition. HTC has said the Developer Edition may have signal issues since it is not "optimized" for AT&T. A few people have commented that ROMs based on the international HTC One may also have signal issues while running on the AT&T HTC One.
So for those of you running international roms such as Android Revolution or TrickDroid -- are you having any signal issues? Is signal strength as good as it was on stock AT&T ROM? Any trouble holding on to an LTE signal?
Thanks.
phositadc said:
Apparently some people are having signal issues (i.e., dropping between HSPA and LTE where other AT&T phones are rock solid LTE) with the Developer Edition. HTC has said the Developer Edition may have signal issues since it is not "optimized" for AT&T. A few people have commented that ROMs based on the international HTC One may also have signal issues while running on the AT&T HTC One.
So for those of you running international roms such as Android Revolution or TrickDroid -- are you having any signal issues? Is signal strength as good as it was on stock AT&T ROM? Any trouble holding on to an LTE signal?
Thanks.
Click to expand...
Click to collapse
I wouldn't say that it's much an issue, but that the international roms show Att true signal strength. For example I have one bar of LTE in my house and my wife's iPhone 5 range from 2 or 3. My LTE speeds are almost double hers. The bars being shown whether on stock Att or international doesn't mean much. A good way to check signal strength would be to compare your db's.
Sent from my HTC One using Tapatalk 2
No issues here. DBM signal, speeds all awesome on the International Roms. AT&T likes to make you believe that your signal is better than it really is.
Signal bars are a lie.
I have -95db signal and decent LTE speed
gunnyman said:
Signal bars are a lie.
I have -95db signal and decent LTE speed
Click to expand...
Click to collapse
Thanks to all for the feedback.
Just a note though, that some aren't complaining about the bars, but about actually dropping LTE connections where other AT&T phones do not.
Sent from my SAMSUNG-SGH-I747
phositadc said:
Thanks to all for the feedback.
Just a note though, that some aren't complaining about the bars, but about actually dropping LTE connections where other AT&T phones do not.
Sent from my SAMSUNG-SGH-I747
Click to expand...
Click to collapse
Yeah, that happens with me in my house sometime (if in my pocket etc) . Somewhere in one of these threads someone mentions how the international will drop connection at about -115db or something and Att drops around -125db. So that could be the reason.
Sent from my HTC One using Tapatalk 2
I flashed my One to the Maximus 7 Rom and have noticed lower bars than usual. I live near a cell phone tower and all phones that I have had as well as others on ATT always have full bars while I can't seem to get more than 2-3. Today my phone started switching between H and LTE and acting weird while driving and it has never done that before. I'm on the latest 1.29 radio firmware and it hasn't helped...not sure how to fix it and for those saying this is just the true reading of signal, I doubt I would be getting such low signals when Im literally about 3 blocks away from a cell tower.
darus214 said:
I flashed my One to the Maximus 7 Rom and have noticed lower bars than usual. I live near a cell phone tower and all phones that I have had as well as others on ATT always have full bars while I can't seem to get more than 2-3. Today my phone started switching between H and LTE and acting weird while driving and it has never done that before. I'm on the latest 1.29 radio firmware and it hasn't helped...not sure how to fix it and for those saying this is just the true reading of signal, I doubt I would be getting such low signals when Im literally about 3 blocks away from a cell tower.
Click to expand...
Click to collapse
I did notice this too. I definitely have lower bars and lower speed as well....I have trickdroid 5.1 installed. I tried the ATT version before getting the dev version and I did not have this issue.
TrickDroid and ARHD both show true signal bars, but they will also switch to 3g from LTE sooner than the stock ATT load. they seem to switch at aound -120db where ATT will hold out until -130db. if you select att from the ARHD load, it hold on till about -125, still not the same but it works.
Like another person said, the stock ATT ROMs show a non real signal strength, where the Int'l ROMs do. It's all about your actual data speeds and the dB signal. I'm running ARHD 7.0 and have zero reception trouble. LTE speeds are fine.
Just replace /system/framework/ext.jar from an AT&T ROM and you'll get the "fake" AT&T signal icons...
Yup
phositadc said:
Apparently some people are having signal issues (i.e., dropping between HSPA and LTE where other AT&T phones are rock solid LTE) with the Developer Edition. HTC has said the Developer Edition may have signal issues since it is not "optimized" for AT&T. A few people have commented that ROMs based on the international HTC One may also have signal issues while running on the AT&T HTC One.
So for those of you running international roms such as Android Revolution or TrickDroid -- are you having any signal issues? Is signal strength as good as it was on stock AT&T ROM? Any trouble holding on to an LTE signal?
Thanks.
Click to expand...
Click to collapse
My Co-worker cant keep the LTE signal for longer than 10 minutes.... and the phone gets hot as heck...is yours hot?
HTC One AT&T Variant TrickDroid 5.2.1 ROM with AT&T tweaks.
RSRP(dBm): -105 to -110 avg. RSRQ(dB): -10 to -12 avg.
No LTE troubles but I did notice during the ROM install before I picked AT&T as carrier it flaked out a few times saying something else besides LTE and H and kept going back and forth.
TrickDroid rom with AOSP icons are showing 1 to 2 bars. - At the bottom!! Whereas my stock rom was showing like 3-4 bars all of the time at the house.
SpeedTest with both roms at my house (not on wifi) = 15M down. 10-20 AVG. regardless of ROM.
So like allot of people in here, I sold off my AT&T S5 and scooped up a T-MO S5 for the obvious reasons. What i've noticed is that i get insanely awesome reception everywhere i go with this t-mo phone. At work i would pull down about 3-4 bars of LTE on my ATT S5 and now i get full LTE all day long without the thing fluctuating once. Not a huge difference but still nice to see. This also goes for just about everywhere i go, full bars galore. Anyone else noticing this? Either way it's just another perk along with root and my custom ROM!!:victory:
Wickidmasshole said:
So like allot of people in here, I sold off my AT&T S5 and scooped up a T-MO S5 for the obvious reasons. What i've noticed is that i get insanely awesome reception everywhere i go with this t-mo phone. At work i would pull down about 3-4 bars of LTE on my ATT S5 and now i get full LTE all day long without the thing fluctuating once. Not a huge difference but still nice to see. This also goes for just about everywhere i go, full bars galore. Anyone else noticing this? Either way it's just another perk along with root and my custom ROM!!:victory:
Click to expand...
Click to collapse
Bars means nothing. Always check and compare using the dbm menu.:good:
The T-Mobile S5 will show five bars for a -99dbm signal. That in reality should be about 2-3 bars.
MattMJB0188 said:
The T-Mobile S5 will show five bars for a -99dbm signal. That in reality should be about 2-3 bars.
Click to expand...
Click to collapse
I don't know about that ; however the TMobile modem has more bands like LTE 900Mhz, HSPDA/AWS 1700Mhz
cjk2010 said:
I don't know about that ; however the TMobile modem has more bands like LTE 900Mhz, HSPDA/AWS 1700Mhz
Click to expand...
Click to collapse
It does. It's a fact. When I have a -99dbm signal, my phone shows 5 bars. Then 4 bars with anything below -110dbm. I am assuming T-Mobile did it this way because their LTE is extremely weak, and they want you to think you have a good signal, when you really don't.
MattMJB0188 said:
It does. It's a fact. When I have a -99dbm signal, my phone shows 5 bars. Then 4 bars with anything below -110dbm. I am assuming T-Mobile did it this way because their LTE is extremely weak, and they want you to think you have a good signal, when you really don't.
Click to expand...
Click to collapse
dbm alone when talking about LTE is a somewhat artificial number without context . RSSI and RSRP will indicate something more meaningful to the signal quality. -99dbm RSRP would be closer to -79 dbm RSSI and is a strong signal .
I am currently at -95dbm RSRP and am pulling phenomenal results.
Sent from my SM-G900T using XDA Premium 4 mobile app
My current signal
Sent from my SM-G900T using XDA Premium 4 mobile app
cjk2010 said:
My current signal
Sent from my SM-G900T using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Don't install the new modem. It causes a problem for ATT users.
rfb813 said:
Don't install the new modem. It causes a problem for ATT users.
Click to expand...
Click to collapse
I'll wait until the new modem is thoroughly tested with AT&T. It can't be that bad.
rfb813 said:
Don't install the new modem. It causes a problem for ATT users.
Click to expand...
Click to collapse
Thanks for the heads up, I am on TMO not ATT , but I think I'll still hold off until I see more results. Seems a lot of ppl are having lower download speeds.
---------- Post added at 12:03 PM ---------- Previous post was at 11:44 AM ----------
I wonder if this new slow download modem issue on G900T tmobile devices on ATT networks has anything to do with ATT lighting band 29 LTE on 700 now?
MattMJB0188 said:
I'll wait until the new modem is thoroughly tested with AT&T. It can't be that bad.
Click to expand...
Click to collapse
Download speeds went from 25+Mps to 1.5Mps.
Wow. I'm glad I still have my original modem. I wonder why they would do that. Unless they don't want people taking their devices over to AT&T?
MattMJB0188 said:
Wow. I'm glad I still have my original modem. I wonder why they would do that. Unless they don't want people taking their devices over to AT&T?
Click to expand...
Click to collapse
We really don't know if this is really happening to everyone or it's an isolated case...so far it's only been the same couple people reporting it.
devoidx said:
We really don't know if this is really happening to everyone or it's an isolated case...so far it's only been the same couple people reporting it.
Click to expand...
Click to collapse
I reflashed the ANCH stock Rom and rerooted and am back on the ANCH modem. Got my speeds back up
This is not an isolated case. There are problems with the new Modem. Go to the Development section. Beanstown has a new thread with all the Modems, firmware, and stock roms.. Try different modems, many times they function differently by location.