Related
i had my phone rooted with Super Clean 2.8 and tried to flash the stock EB01 Odin from here http://forum.xda-developers.com/showthread.php?t=977493
the phone took a very long time to go through the steps of Odin and got stock at recovery.bin for over an hour then it "failed" now the phone will not turn on or charge or even go into download mode
not sure how to get the phone into download mode manually sorry i always use the power menu built into Super Clean
is my phone bricked?
please help
Nah, you should be able to retry.
1. Take your battery out.
2. Hold down "Volume down" while plugging the USB cable into your phone (and the computer of course).
3. Retry the Odin package. It shouldn't take more than 10 or so minutes (from what I've heard, mine have never taken longer than about 3.
if that doesnt work you may need a jig its not hard to make one or you can buy online just search in the forums here for jig it should come up
i just recovered from a soft brick via home made jig telus fascinate same as vibrant (U.S.)
thank for the help
thanks for the help but my phone will not boot in to download mode i have tried time and time again and nothing comes up on the screen
i may just take the phone to Verizon after work today i have the insurance so they should replace it for free
attempt to bring up download mode, then check odin to see if a yellow light shows up. Sometimes the download mode logo can disappear, however the phone is still able to flash.
Good luck.
went to the Verizon store they are sending me a replacement phone for free
it always helps to have the extended warranty
and i have all my apps back up through titanium backup so it should not take long to get it all up and running again
1st time i ever bricked a phone in 3 years of running custom roms
thanks for the help guys
I think you had an hardware failure. Not that I've read ever thread on every board about the Fascinate, or that I've only been reading for two months, but I do read multiple boards daily and this would be the first hard brick I've read about.
Glad the insurance got you a new phone.
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Remove Kies and reinstall see if it picks the phone up and installs the drivers .
jje
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
That kernel is for the Epic touch 4g is that your phone or do you have the international version? If you flashed the wrong kernel it could cause problems.
Yes it's an Epic touch 4g from sprint.
EDIT: Uninstalled Kies, reinstalled Kies, restarted computer, still no kind of recognition of my phone in any state (powered off, at "Firmware upgrade encountered" screen it boots into, or in download mode). Starting to get nervous, I used to at least hear a sound when plugging my phone into my comp. It is like there is nothing on the other end of the USB cable.
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
OperationIvy85 said:
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
Click to expand...
Click to collapse
Try to reset your binary counter with a usb jig.
you could try and download the drivers again from here and see if it then connects
http://modem-techno.blogspot.com/2010/09/epic-4g-usb-driver-download.html
I also had a similar problem once with an old i9000 and what worked was doing this and then connecting the phone first and then opening Odin.For some reason opening Odin first and connecting wouldnt find the phone.If nothing else works try wipeing the bin counter with the jig and send it back.Youll have to say that kies crashed while updating on Win7 64bits.Samsung know that before the September 30th kies update kies wasnt fully functional with 64bit drivers and they had a few phones replaced under warranty because of crashing kies updates on Win7 64bits.
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
The good thing is that your bin counter is at "0" again.The Kies thing is the real deal as there are also posts here on XDA of the same thing happening.I also know its true from first hand experience as it has happened to me and when i told them about the Win7 64bit driver problem (this happened to me a couple of months back too) they had no option but to accept it cos they know its true.Also i offered to e-mail links from forums with other complaints from users on 64bit PCs but they didnt even dought my storey and in 4 days it was back in my hand.I told them that when the update finalized the programe froze and the phone rebooted to a black screen.Had to pull the battery cos it appeared to be dead and refused to reboot again.Important to say that you where on Kies prior to the update I mentioned.Ived update to the latest Kies and it works fine now on my Win7 64bit so be carefull there that date is important
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
OperationIvy85 said:
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
Click to expand...
Click to collapse
Kies via to its Sep 30th update was not fully compatable with 64bits and gave a lot of problems to a lot of people.I had a few problems with it when I got a new laptop (HP Win7 64bit) so started searching the web for solutions and found that kies was designed mainly to support the windowsXP versions 32bit and had caused Samsung to accept various repairs under warranty because of crashing Kies updates mainly on android running phones.For some reason Bada didnt seam to affected.Maybe cos there arnt to many around like android.In the 4G forum there is post from someone who has bricked their phone using Kies to update and a reply from another with the same problem.Take it into where you bought it to start with and if its not there problem then they might send it back to Samsung for you.All you need to say is that you where updating your firmware via kies and on completion it froze and the phone booted to a black screen like mine did.You had to pull the battery and restart your PC to close Kies cos it wouldnt close or minimize or anything.Tell them that you searched on the net for possible causes and found what i told you about Kies and since you have a Win7 64bits PC then thats most likely to have been the cause.Your bin counter is at 0 so there is no way they can counter-attack your story.
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Who told you that the exclamation point means you voided your warranty?
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The sign you see means that your phone is semi-bricked and that you needed a jig to force the phone to boot into download mode.You can buy one on ebay for a couple of bucks.Best you do cos it could may mean that your warranty is void.Let me explain,no one can actually say that your warranty is void because of this sign but being only "semi-bricked" the service centre are still able to enter the phone and see the bin counter.So if you semi-bricked flashing a non official firmware or you have done so earlier and your bin counter is not at 0 then YES your warranty is void.Semi-brick is not so bad as you can normally fix it yourself but Hard-brick is a dead phone and you gotta pay for a jtag .In your case buy a jig force the phone into download mode and re-flash it yourself.You shouldnt need to go anywhere.Semi-bricking is something you save yourself.Just wait till the jig arrives in the mail.
EDIT:there have been posts of people pulling the battery for 10min and re-trying and it has booted to download.They say they have had to do so 4 or 5 times for it to finally work but if youve got time on your hands then give it a try.
---------- Post added at 04:48 PM ---------- Previous post was at 04:22 PM ----------
OperationIvy85 said:
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
Click to expand...
Click to collapse
Well at least you got a phone now hope they didnt charge to much!!!!Good on ya mate
Update on my issue....
It turns out the problem is because I tried to flash an I1900 firmware while my phone is a G variant (I900G).
After using the right firmware, it worked.
OperationIvy85 said:
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
Click to expand...
Click to collapse
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
sfoksn said:
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
Click to expand...
Click to collapse
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
aceofclubs said:
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
Yeah, I got stuck while flashing 2.3.5 Gingerbread... Yeah I think it has a new bootloader, as I remember Odin updating the bootloader section before messing up.
Is there any way I can get the USB jig to work? My phone is no longer recognized by the USB anymore so I can't even flash another bootloader or anything.
Is there anythign I could do to make the USB jig work without connecting it to the computer?
Can you get into download mode using the buttons?
Volume down+home+power
If so try and flash another Rom from intratechs thread to get back to stock.
If that works you can try again.
Sent from my GT-I9100 using XDA App
Hey all, this is my first android and I'm not the smartest sometimes. I tried restoring back to factory rom, and watched a bad how to vid. Basically i cleared data, system, cache and now realize i shouldn't have.
I'm not able to connect to the phone through usb. I have the drivers, but I can't see the phone.I can boot into cwm, and that is it. When i start it, it basically pulls up the LG screen, then a black screen.
I have a backup on cwm but get the md5 error.
Is it possible to put the sd card in my computer and download what i need straight to the card? Im also not sure what i need to download, if that does work.
Please let me know if there is any other info I can provide. Like i said im not the smartest sometimes, so dont be afraid to respond like im slow.
Cat Rancher said:
Hey all, this is my first android and I'm not the smartest sometimes. I tried restoring back to factory rom, and watched a bad how to vid. Basically i cleared data, system, cache and now realize i shouldn't have.
I'm not able to connect to the phone through usb. I have the drivers, but I can't see the phone.I can boot into cwm, and that is it. When i start it, it basically pulls up the LG screen, then a black screen.
I have a backup on cwm but get the md5 error.
Is it possible to put the sd card in my computer and download what i need straight to the card? Im also not sure what i need to download, if that does work.
Please let me know if there is any other info I can provide. Like i said im not the smartest sometimes, so dont be afraid to respond like im slow.
Click to expand...
Click to collapse
Can you install the Rom "The base .5". I assume so if you can get to cwm. I had this problem when flashing this Rom The first time. It did the same thing with the LG logo then go black. If that happens just reboot to cwm(May take awhile) and reflash "the base" again. That should allow it to boot the phone fully so you can at least use it till you can get all the way back to stock. I hope this helps. I have to crash now tho. I'll check back in the morning to see how it's going.
Sent from my UNLOCKED LG-E970 using xda premium
Are you trying to get back to factory settings or just get your phone running with the stock rom?
You should be able to just put the ROM on your sd card via computer if you have an SD card sleeve.
If you wiped your phone, it's my understanding that you're not supposed to when flashing the provided rom in development.
There's a posting in development, I believe, about restoring your phone to stock if you messed it up. LGNST or something.
Cat Rancher said:
Hey all, this is my first android and I'm not the smartest sometimes. I tried restoring back to factory rom, and watched a bad how to vid. Basically i cleared data, system, cache and now realize i shouldn't have.
I'm not able to connect to the phone through usb. I have the drivers, but I can't see the phone.I can boot into cwm, and that is it. When i start it, it basically pulls up the LG screen, then a black screen.
I have a backup on cwm but get the md5 error.
Is it possible to put the sd card in my computer and download what i need straight to the card? Im also not sure what i need to download, if that does work.
Please let me know if there is any other info I can provide. Like i said im not the smartest sometimes, so dont be afraid to respond like im slow.
Click to expand...
Click to collapse
The recovery won't generate a md5 sum (known bug). You have to generate it yourself. Connect your phone to adb and go to #4 in the FAQ here.http://forum.xda-developers.com/showthread.php?t=2006946
Note that there is no way to tell of the backup is corrupt since you are generating a valid code regardless of integrity.
Sent from my LG-E970 using xda premium
Murasakiii said:
Are you trying to get back to factory settings or just get your phone running with the stock rom?
You should be able to just put the ROM on your sd card via computer if you have an SD card sleeve.
If you wiped your phone, it's my understanding that you're not supposed to when flashing the provided rom in development.
There's a posting in development, I believe, about restoring your phone to stock if you messed it up. LGNST or something.
Click to expand...
Click to collapse
I tried re-installing .4 base which is what I had originally used. It let me choose the apps to instal, and made it to the "X" screen, but appeared to be stuck in a boot loop. I am going to try and download and install .5 via the sd card and see if that works. I'm not sure if LGNPST will work since I can't see the phone via usb. I will download it and give it a try though.
I also saw the guide in the general Optimus G forums for unbricking it.
http://forum.xda-developers.com/showthread.php?t=2010624
Since i cant really connect via usb, ill probably have to use a different method. Im hoping the usb issue is due to the computer im using and the original computer i used to root and unlock will work.
Cat Rancher said:
I tried re-installing .4 base which is what I had originally used. It let me choose the apps to instal, and made it to the "X" screen, but appeared to be stuck in a boot loop. I am going to try and download and install .5 via the sd card and see if that works. I'm not sure if LGNPST will work since I can't see the phone via usb. I will download it and give it a try though.
I also saw the guide in the general Optimus G forums for unbricking it.
http://forum.xda-developers.com/showthread.php?t=2010624
Since i cant really connect via usb, ill probably have to use a different method. Im hoping the usb issue is due to the computer im using and the original computer i used to root and unlock will work.
Click to expand...
Click to collapse
The method in that link is for phones that don't have official firmware to use with lgnspt. If you san get into download mode (power off phone ,connect usb,hold volume down and up plus power ) you should be able to lgnpst back to stock.
adfurgerson said:
The method in that link is for phones that don't have official firmware to use with lgnspt. If you san get into download mode (power off phone ,connect usb,hold volume down and up plus power ) you should be able to lgnpst back to stock.
Click to expand...
Click to collapse
Alright. I was able to get into download mode. I downloaded lgnpst. Do you have an idea where i would find the other necessary files? Again, total noob. Sorry for all the hand holding. You guys have been great!
Cat Rancher said:
Alright. I was able to get into download mode. I downloaded lgnpst. Do you have an idea where i would find the other necessary files? Again, total noob. Sorry for all the hand holding. You guys have been great!
Click to expand...
Click to collapse
You need to go to the IRC channel to grab the new version of lgnpst and the correct files.
Sent from my LG-E970 using xda premium
Cat Rancher said:
Alright. I was able to get into download mode. I downloaded lgnpst. Do you have an idea where i would find the other Didnecessary files? Again, total noob. Sorry for all the hand holding. You guys have been great!
Click to expand...
Click to collapse
Did you get your phone straightened out?
adfurgerson said:
Did you get your phone straightened out?
Click to expand...
Click to collapse
I'm traveling for work and on a work computer, so the IRC channel is blocked. Of course. I'm heading home tomorrow so hopefully I can get everything back to normal when i get on my home computer. (not having a phone sucks)
Do you all think it would be worth putting the base .5 on my sd card and flashing that, or do you think that wouldnt work? .4 is on there now from my original flash, but that won't work. Just curious.
Well is your phone up and running?
I would think it wouldn't cause harm to try and flash .5 onto it, your phone shouldn't get bricked from it.
i agree with Murasakiii
should be fine to run .5
DraginMagik said:
i agree with Murasakiii
should be fine to run .5
Click to expand...
Click to collapse
Welp, I think i earned the title of first bricked phone. It was able to get into recovery and download mode a couple days ago, but now it wont charge it seems. So i cant get it into any mode to do anything. Ive had it on the charger, wall and usb for a couple hours and nothing is happening. I wonder if i can take it back to my att store and try get a replacement. It is within my 14 day window, and there are "hardware" warranties. I have a feeling they will ask what happened and while i may not initially divulge everything, i sadly cant lie. And since its all my fault, i may chalk it up to learning.
i'd say the device started having issues with the USB. unable to see the device when plugged into the computer and the device won't take a charge. don't hear of too many authentic "bricking's" anymore...it can almost always be resurrected. but if the device won't take a charge your time to resolution is rather limited. good luck.
Cat Rancher said:
Welp, I think i earned the title of first bricked phone. It was able to get into recovery and download mode a couple days ago, but now it wont charge it seems. So i cant get it into any mode to do anything. Ive had it on the charger, wall and usb for a couple hours and nothing is happening. I wonder if i can take it back to my att store and try get a replacement. It is within my 14 day window, and there are "hardware" warranties. I have a feeling they will ask what happened and while i may not initially divulge everything, i sadly cant lie. And since its all my fault, i may chalk it up to learning.
Click to expand...
Click to collapse
Before you leave to go to the store hook it up to a set up jumper cables and then attach the other end to your car battery. Then just tell them when you tried to charge it that it started smoking and wont turn on any more.
The only lie you have to tell them is it happened on the stock charger.
Im on the same boat. Tried going back to stock for a warranty return, and i ended up bricking the phone. Im able to get it to download mode and was able to run the lg tool but it keeps failing on me. And when it does complete it still wont load. Im going to try to make my self a powerd usb cable too see if i can get it to work. Have like 2 or 3 days to try to figure it out. Or elese im out 550 bucks.
Sent from my LG-E970 using xda app-developers app
Other option is just telling them you clicked install for the ota update it rebooted and never came back on. They just wipe them at the repair center anyway if they get them to boot up.
Cat Rancher said:
Welp, I think i earned the title of first bricked phone. It was able to get into recovery and download mode a couple days ago, but now it wont charge it seems. So i cant get it into any mode to do anything. Ive had it on the charger, wall and usb for a couple hours and nothing is happening. I wonder if i can take it back to my att store and try get a replacement. It is within my 14 day window, and there are "hardware" warranties. I have a feeling they will ask what happened and while i may not initially divulge everything, i sadly cant lie. And since its all my fault, i may chalk it up to learning.
Click to expand...
Click to collapse
It took 12 hrs to get a clean download of the stock ROM (AT&T internet sucks in my area). The entire time the screen on my phone was on with the LG splash screen displayed. By the time I got the ROM ready for flash, the battery was dead. I was however able to plug in to the USB on my computer and get enough juice to get into download mode. Ran LGNPST (v2.2.3) and the stock ROM installed with no prob. You might try plugging it in then trying to get into download mode.
EDIT: now that I think about it. You need to have it plugged in to the USB before download mode anyway, so you won't be doing anything different than you already did.
Hey guys
1) Restarted my phone today using CM10.1 from a very recent nightly (within the past week).
2) On restart, phone froze and got kernel panic.
3) Restarted into CWM and tried to do a restore to an earlier backup I had made.
4) Half-way through the restore, I got ANOTHER kernel panic (never had that before)...
5) Only things I could do with the phone after that was enter download mode...nothing else...couldn't enter recovery mode anymore.
6) Went into download mode and flashed this CWM-Recovery (http://forum.xda-developers.com/showthread.php?t=1118693) and followed the instructions to the letter.
7) Odin 3.07 hung on NAND Write Start
8) Tried using Odin 1.3, and it seemed to flash correctly. It says completed no errors.
Phone will now not even start and is completely unresponsive...pressing any combination of buttons will not start the phone, and the phone is not recognized in Odin anymore...did I just hard brick it? Any other ideas?
Thanks,
Elliott
Service centre. Although if you can have someone who does JTAG's have a look at it to determine whether it can be JTAG'd without you giving them any money up front (I.E you only pay them if it can be JTAG'd), try that first.
Thanks that's what I thought.
Also, try a jig if you can get one. In all likelihood won't work, but stranger things have happened & you have nothing to lose.
Yeah thanks that's what I plan on doing. Any idea what I did wrong, though? I don't want it to happen again if I get it working with a jig.
Impossible to say. Not sure why you flashed that nondescript kernel/recovery in that situation tho given it probably wouldn't have worked even if the flash had been successful (You would probably have ended up with bootloop given recovery was obviously 'broken'). I would have flashed stock with Odin (And that's certainly what I tell people in your situation on here to do because it normally works).
But flashing recovery rather than a stock rom probably didn't break your phone, put it that way, so you didn't do anything 'wrong' per se. Just remember if you get into a similar situation again, go back to stock via Odin & start again (re-root your phone/restore a backup, flash your custom rom/kernel again, etc).
If the jig works (and don't get your hopes up or anything, we're talking a 1 in 10,000 chance, and that's probably being generous), flash stock with Odin (you wont have much choice).
Well...brought it to a JTAG specialist today and he couldn't fix it either...says it's very rare and he's had 5 out of 80 S2's like this happen without being able to fix them...
Bummer. Motherboard replacement in that case. If the phone's under warranty, take it to a service centre & say as little as possible. You might blag it for a warranty fix. No warranty ? You can still have a new motherboard put in by a service centre (more expensive option usually), or you can source a 2nd hand MB from a 'donor' phone (one with a broken screen that's otherwise OK, etc) & either swap it in yourself or pay a local mobile repair shop to do it (usually cheaper option).
@ OP By following what you flashed I noticed the date, we're talking about a 2 years old thread, a lot have changed since.
Not sure that was what bricked your device but I get that panic mode.
The other thing that it comes to mind is nand corruption, which has been quite common these days with people running custom.
I'm with bungle there, the best recovery package is going back to stock and start fresh.
I, on the other hand, wouldn't accept the situation you are on, I would spend a whole week trying to get that phone to boot again, whether a second opinion on a jtag, a new jig, another battery or any other thread on here at xda.
If the device gets hot near the rear camera and it won't even charge nor get warm around that area dismiss what I just said and proceed with the mobo replacement bungle suggested.
And of course, if you did something else to your device and didn't share it please, come clean so others don't freak out by reading this.
Sent from...this is not even my S2
Hey
Nothing else was done to the device...just what I stated exactly.
I caved today and bought a BNIB S3 because I couldn't go without a phone anymore...
Thanks for the help, guys
Elliott
Hello all...hoping to get some assistance with this thing. Long story short, debloated it due to horrid battery life and high heat. Everything was great until about a week ago when my settings app go renamed somehow. Tried fixing it but couldn't find the com.android.settings file with the correct signature for my phone (AT&T, US Model, unlocked, not rooted).
It's been working fine except no settings...so I backed up the usual stuff and had plans to do a factory reset this weekend. A few hours ago I picked it up and it went all wonky on me. Upon boot, it comes up to the lock screen and then the screen just starts turning on/off. I'm unable to bring up the passcode screen...but, am able to bring up the power menu by holding the power button. But, can't power down or get into safe mode that way. After about 5 seconds of doing this, it reboots. Rinse and repeat. Safe mode via buttons starts, but, does the same thing.
I am able to get into both recovery mode and download mode though. I can view logs/etc.
Normally, I'd just ***** and moan, then do the factory reset, However, I made one huge oversight when I backed up my data earlier this week and forgot to backup my notes. There's about a dozen of them, pages and pages long with all the medical details regarding my sons illness that I've been tracking for years. It's a nightmare dealing with different Dr's all the time so I've logged it all on the phone. Unfortunately, the best app I've found for it doesn't do cloud storage and keeps them saved as local txt files on the device.
Is there any hope I can somehow pull the files using recovery/download mode or utilize the logs to determine the errors and fix it enough to be able to get them? I'm fairly tech savvy and have ADB installed. I'm super ADD though and my head is just spinning trying to sort through all the possible posts regarding trying to do this...many being for older phones.
Absolute worst case, is there a legitimate service that would be able to do it?
Any help recovering my son's medical notes would be really really appreciated.
RiBBiTeDD said:
Hello all...hoping to get some assistance with this thing. Long story short, debloated it due to horrid battery life and high heat. Everything was great until about a week ago when my settings app go renamed somehow. Tried fixing it but couldn't find the com.android.settings file with the correct signature for my phone (AT&T, US Model, unlocked, not rooted).
It's been working fine except no settings...so I backed up the usual stuff and had plans to do a factory reset this weekend. A few hours ago I picked it up and it went all wonky on me. Upon boot, it comes up to the lock screen and then the screen just starts turning on/off. I'm unable to bring up the passcode screen...but, am able to bring up the power menu by holding the power button. But, can't power down or get into safe mode that way. After about 5 seconds of doing this, it reboots. Rinse and repeat. Safe mode via buttons starts, but, does the same thing.
I am able to get into both recovery mode and download mode though. I can view logs/etc.
Normally, I'd just ***** and moan, then do the factory reset, However, I made one huge oversight when I backed up my data earlier this week and forgot to backup my notes. There's about a dozen of them, pages and pages long with all the medical details regarding my sons illness that I've been tracking for years. It's a nightmare dealing with different Dr's all the time so I've logged it all on the phone. Unfortunately, the best app I've found for it doesn't do cloud storage and keeps them saved as local txt files on the device.
Is there any hope I can somehow pull the files using recovery/download mode or utilize the logs to determine the errors and fix it enough to be able to get them? I'm fairly tech savvy and have ADB installed. I'm super ADD though and my head is just spinning trying to sort through all the possible posts regarding trying to do this...many being for older phones.
Absolute worst case, is there a legitimate service that would be able to do it?
Any help recovering my son's medical notes would be really really appreciated.
Click to expand...
Click to collapse
Man, i'm so sorry to hear that :/
Sience you have access to recovery, did you try to wipe only cache partition and hit repair apps(also in recovery)?
I'm also using debloated device and i dont have any problems with it
nocio said:
Man, i'm so sorry to hear that :/
Sience you have access to recovery, did you try to wipe only cache partition and hit repair apps(also in recovery)?
I'm also using debloated device and i dont have any problems with it
Click to expand...
Click to collapse
Yeah...that's the first thing I tried after safe mode failed. :\
There's quite a few folks reporting similar issues since the last OTA update a couple weeks ago.
Usually I delay until I get a chance to restore then allow it...this one didn't even give me a chance. I was using my phone when it popped up. No option to remind me later. When I tried to exit it counted down from 10, rebooted and installed.
RiBBiTeDD said:
Yeah...that's the first thing I tried after safe mode failed. :\
There's quite a few folks reporting similar issues since the last OTA update a couple weeks ago.
Usually I delay until I get a chance to restore then allow it...this one didn't even give me a chance. I was using my phone when it popped up. No option to remind me later. When I tried to exit it counted down from 10, rebooted and installed.
Click to expand...
Click to collapse
I have one idea, it may seem unusual but it may work.
Try to remove sim card and than boot device
nocio said:
I have one idea, it may seem unusual but it may work.
Try to remove sim card and than boot device
Click to expand...
Click to collapse
Thanks for the idea. But, yeah, tried that to already...cleared cache and repaired apps afterwards too. Tried it with cable, tried a 2.0 cable too.
No dice.
The app repair works just fine and then it does the same thing when lock screen tries to appear.
RiBBiTeDD said:
Thanks for the idea. But, yeah, tried that to already...cleared cache and repaired apps afterwards too. Tried it with cable, tried a 2.0 cable too.
No dice.
The app repair works just fine and then it does the same thing when lock screen tries to appear.
Click to expand...
Click to collapse
Only thing that came to my mind is to download latest firmware for your device than flash it via odin
EDIT: but be carefull with that. Odin have box to untick factory reset but i didnt do that a loooooooooong time so i dont know if something is changed
nocio said:
Only thing that came to my mind is to download latest firmware for your device than flash it via odin
EDIT: but be carefull with that. Odin have box to untick factory reset but i didnt do that a loooooooooong time so i dont know if something is changed
Click to expand...
Click to collapse
Yeah, I figured that'd be my last shot at it... I've read the horror stories of tripping Knox even with factory firmware.
Was just really hoping there was some way to yank the stuff using recovery or download modes.
RiBBiTeDD said:
Yeah, I figured that'd be my last shot at it... I've read the horror stories of tripping Knox even with factory firmware.
Was just really hoping there was some way to yank the stuff using recovery or download modes.
Click to expand...
Click to collapse
I think that you can't trip Knox only when you flash official firmware over unlocked bootloader and custom ROM, but I'm not so sure.
Last time I did that is when I had Samsung Galaxy S2 and flashing official firmware over official firmware and that didn't trip the Knox counter
Does flashing genuine firmware trip knox?
Hi It's been a while since I bothered flashing firmware so I am not upto date with how things work now. My questions are I am currently on 02s version of firmware and would like to go samsungs version so I can take part in things like the one...
forum.xda-developers.com
Here you can see that flashing official firmware over official firmware(i'm guessing that you are not rooted) won't trip knox counter
nocio said:
Does flashing genuine firmware trip knox?
Hi It's been a while since I bothered flashing firmware so I am not upto date with how things work now. My questions are I am currently on 02s version of firmware and would like to go samsungs version so I can take part in things like the one...
forum.xda-developers.com
Here you can see that flashing official firmware over official firmware(i'm guessing that you are not rooted) won't trip knox counter
Click to expand...
Click to collapse
Awesome! Thank you!
I was able to get the files...for others in the same boat, here's a link to what worked for me:
Help finding correct firmware and installing for AT&T SM-G991U.
Hello all...I'm a fellow victim of the OTA updates screwing us debloaters currently stuck in a boot-loop. I'm trying to recover my the past several years text notes containing all the medical details for my son's illness. Details on that can be...
forum.xda-developers.com