I have order a factory cable, but still i am not able to boot my razr xt910
i am getting this message:
AP fastboot Flash Mode (S) (Flash Failure)
0A.6C
To return to normal mode - first press power key to power down
Device is LOCKED, Status code: 0
Battery OK
OK to Program
Transfer mode:
USB Connected
Please help me, i am trying to resolve this problem since two weeks
This happened to me 2 days ago while testing without my daily caffeine.
http://forum.xda-developers.com/showpost.php?p=25354339&postcount=210
IDK if you have access to, or are comfortable with doing what I did. That's your only option until you get that cable.
I have the factory cable
i have the factory cable but still i am not able to install any rom on it
yaloraibi said:
i have the factory cable but still i am not able to install any rom on it
Click to expand...
Click to collapse
What's wrong?
Sent from my XT910 using Tapatalk 2
where did you get the "factory" cable?
yaloraibi said:
I have order a factory cable, but still i am not able to boot my razr xt910
i am getting this message:
AP fastboot Flash Mode (S) (Flash Failure)
0A.6C
To return to normal mode - first press power key to power down
Device is LOCKED, Status code: 0
Battery OK
OK to Program
Transfer mode:
USB Connected
Please help me, i am trying to resolve this problem since two weeks
Click to expand...
Click to collapse
It's difficult to help when there is a lack of information for anyone to help you.
If you can't update with RSD lite, try RSD alternative:
http://forum.xda-developers.com/showthread.php?t=1453660
If you have the factory cable, always use that when flashing.
pedrotorresfilho said:
What's wrong?
Sent from my XT910 using Tapatalk 2
Click to expand...
Click to collapse
I am usin RSD to upload the rom but still i am getting error, this is the rome (SPYDERIRD_U.01.26.0_SPD-IRD-21_SIGN_MEA_RETAIL.xml)
Rouxe41 said:
where did you get the "factory" cable?
Click to expand...
Click to collapse
I got thr cable from ebay
I used the same ROM for my RAZR bought in Kuwait a week ago and everything was just fine. But I had 100% charged battery. Where are you from?
borisgraovac said:
I used the same ROM for my RAZR bought in Kuwait a week ago and everything was just fine. But I had 100% charged battery. Where are you from?
Click to expand...
Click to collapse
I am from Bahrain, if you can help me out to resolve my problem
why dont you go back to stock first?
Sent from my ICS Droid RAZR using xda premium
Rouxe41 said:
why dont you go back to stock first?
Sent from my ICS Droid RAZR using xda premium
Click to expand...
Click to collapse
How i can go back to STOCK?
yaloraibi said:
I am from Bahrain, if you can help me out to resolve my problem
Click to expand...
Click to collapse
This is how I did it. You need RSD Lite 5.6 and ROM you already have and, of course, pretty much battery charged (50% at list, otherwise could be a mess). Also, you need ADB installed on your computer in order to get the phone recognised.
Power down your device. Press and hold the Vol+ and Vol- keys, then press and hold the power button until a white screen appears and you can now release all three buttons.
Use the Vol- key (and ONLY the Vol- key) to scroll through the list. Scroll until “AP Fastboot” is highlighted and press the Vol+ key to select it.
Connect the USB cable to both your PC and phone. NOTE: At this time, you may see drivers trying to install but they may not all be successful (that’s okay). But your computer does need to recognize your Razr as a ADB interface device (if it does not, you probably do not have ADB configured properly and you will not be able to flash your phone.
Open RSD Lite and use the program (button to the right of the “Filename:” box) to open the .zip file containing your fastboot files.
When prompted, select the “Uncompress Only” button on your PC.
After it has uncompressed the files, ensure that RSD Lite shows “connected” on one of the ports and make sure that your phone shows “USB Connected”. If you are still not connected you may need to unplug the device and plug it back in (I had to do this one of the times I did this procedure).
Press the “Start” button at the top of the RSD Lite application and let it do it’s thing. Don’t touch the phone, don’t unplug the phone…just walk away or sit quietly and watch. This process should take approximately 15-20 minutes in total so BE PATIENT and just wait!
Once the steps have completed, your phone will reboot…JUST KEEP WAITING. You will see the stock recovery screen and it will need a few minutes to flash the factory ROM.
When you see the phone’s lock screen you disconnect the USB cable and close RSD Lite.
borisgraovac said:
This is how I did it. You need RSD Lite 5.6 and ROM you already have and, of course, pretty much battery charged (50% at list, otherwise could be a mess). Also, you need ADB installed on your computer in order to get the phone recognised.
Power down your device. Press and hold the Vol+ and Vol- keys, then press and hold the power button until a white screen appears and you can now release all three buttons.
Use the Vol- key (and ONLY the Vol- key) to scroll through the list. Scroll until “AP Fastboot” is highlighted and press the Vol+ key to select it.
Connect the USB cable to both your PC and phone. NOTE: At this time, you may see drivers trying to install but they may not all be successful (that’s okay). But your computer does need to recognize your Razr as a ADB interface device (if it does not, you probably do not have ADB configured properly and you will not be able to flash your phone.
Open RSD Lite and use the program (button to the right of the “Filename:” box) to open the .zip file containing your fastboot files.
When prompted, select the “Uncompress Only” button on your PC.
After it has uncompressed the files, ensure that RSD Lite shows “connected” on one of the ports and make sure that your phone shows “USB Connected”. If you are still not connected you may need to unplug the device and plug it back in (I had to do this one of the times I did this procedure).
Press the “Start” button at the top of the RSD Lite application and let it do it’s thing. Don’t touch the phone, don’t unplug the phone…just walk away or sit quietly and watch. This process should take approximately 15-20 minutes in total so BE PATIENT and just wait!
Once the steps have completed, your phone will reboot…JUST KEEP WAITING. You will see the stock recovery screen and it will need a few minutes to flash the factory ROM.
When you see the phone’s lock screen you disconnect the USB cable and close RSD Lite.
Click to expand...
Click to collapse
The issue is i already try to install the rom with less battery "less than 50 %", then my phone stooped charging and did not work, that why i have ordered the factory cable
yaloraibi said:
The issue is i already try to install the rom with less battery "less than 50 %", then my phone stooped charging and did not work, that why i have ordered the factory cable
Click to expand...
Click to collapse
Here in this forum is thread "Low Battery charge in Ap Fastboot Fix". Might be helpful. Also, I remember the another thread here explaining how to make "factory cable" by yourself. Maybe the cable you've got is mulfunction.
RSD Lite 5.7 failed
borisgraovac said:
This is how I did it. You need RSD Lite 5.6 and ROM you already have and, of course, pretty much battery charged (50% at list, otherwise could be a mess). Also, you need ADB installed on your computer in order to get the phone recognised.
Power down your device. Press and hold the Vol+ and Vol- keys, then press and hold the power button until a white screen appears and you can now release all three buttons.
Use the Vol- key (and ONLY the Vol- key) to scroll through the list. Scroll until “AP Fastboot” is highlighted and press the Vol+ key to select it.
Connect the USB cable to both your PC and phone. NOTE: At this time, you may see drivers trying to install but they may not all be successful (that’s okay). But your computer does need to recognize your Razr as a ADB interface device (if it does not, you probably do not have ADB configured properly and you will not be able to flash your phone.
Open RSD Lite and use the program (button to the right of the “Filename:” box) to open the .zip file containing your fastboot files.
When prompted, select the “Uncompress Only” button on your PC.
After it has uncompressed the files, ensure that RSD Lite shows “connected” on one of the ports and make sure that your phone shows “USB Connected”. If you are still not connected you may need to unplug the device and plug it back in (I had to do this one of the times I did this procedure).
Press the “Start” button at the top of the RSD Lite application and let it do it’s thing. Don’t touch the phone, don’t unplug the phone…just walk away or sit quietly and watch. This process should take approximately 15-20 minutes in total so BE PATIENT and just wait!
Once the steps have completed, your phone will reboot…JUST KEEP WAITING. You will see the stock recovery screen and it will need a few minutes to flash the factory ROM.
When you see the phone’s lock screen you disconnect the USB cable and close RSD Lite.
Click to expand...
Click to collapse
I have tried RSD Lite and Flash me to flash many different stock oms without any success i am getting same error as the message of this thread like bot failure please someone me... i have no factory cable don't know exactly what is that and i am sure its not readily available where i live.
Okay this is what happened. I own the razr maxx and i got a little impacient and decided to download the leaked .210 4.0.4 motorola ota. That went fine and i was running that for 4 days. Then i wanted to go back to stock 2.3.6 so i used the Mats Utility 1.6 to do so i let it do its thing and i came back and i turned on the phone. It booted up to the M logo and then a couple seconds later the screen turns black. I really need help on this. I have tried using RSD light and flashing the stock rom but it says flash failed. I can boot into stock recovery and everything else.
Can someone help?
Chuckleb0ne said:
Okay this is what happened. I own the razr maxx and i got a little impacient and decided to download the leaked .210 4.0.4 motorola ota. That went fine and i was running that for 4 days. Then i wanted to go back to stock 2.3.6 so i used the Mats Utility 1.6 to do so i let it do its thing and i came back and i turned on the phone. It booted up to the M logo and then a couple seconds later the screen turns black. I really need help on this. I have tried using RSD light and flashing the stock rom but it says flash failed. I can boot into stock recovery and everything else.
Can someone help?
Click to expand...
Click to collapse
Once on .210, there is no going back to GB (2.3.6).....Thinking you are probably screwed. Might be able to reflash .210 or .211
You can try and flash back, but future reference heed the warnings.
Sent from my DROID RAZR using XDA
Chuckleb0ne said:
Okay this is what happened. I own the razr maxx and i got a little impacient and decided to download the leaked .210 4.0.4 motorola ota. That went fine and i was running that for 4 days. Then i wanted to go back to stock 2.3.6 so i used the Mats Utility 1.6 to do so i let it do its thing and i came back and i turned on the phone. It booted up to the M logo and then a couple seconds later the screen turns black. I really need help on this. I have tried using RSD light and flashing the stock rom but it says flash failed. I can boot into stock recovery and everything else.
Can someone help?
Click to expand...
Click to collapse
I was in the same boat but in order to get recovery I had Vol+ Down for quite a bit maybe 40 sec. It flashed a bar. Here was the catch. if I continued to depress the power button plus V0l+ and Vol- I git the black screen The trick is to release power and depress Vol+ & Vol- when it shuts down. From there you can get to recovery etc.
If i wanted to go back to .210 how do i go along doing so?
Originally Posted by [TSON]
If you're on .181
1. Fastboot to .181 to make sure you're completely stock
2. Root
3. Install ROM Manager
4. DO NOT CLICK INSTALL RECOVERY, AND DO NOT INSTALL BOOTSTRAP
5. Copy the update file and the .crc to /cache
6. Open /cache in a file browser of your choosing that will prompt you which application to use instead of opening the .zip file itself (ES File Explorer seems most popular)
7. Tap on the .zip and open it with ROM Manager
8. Don't check anything in the popup and reboot recovery
9. It will flash and finish
10. Done! I recommend factory resetting again here. Reroot if you want.
If you're on a previous ICS leak, above .79
- PUT THE .206 UPDATE FILE ON YOUR EXTERNAL SD CARD FIRST.
You will not be able to use your RAZR to put the files on the SD card after you begin. Please do so beforehand.
- Open the Droid Razr Utility 1.6
- Turn your phone off, & then turn it back on holding VOL DWN and PWR to boot into AP Fastboot
- Select Fastboot to .181 in the Utility & follow the onscreen directions
- Let it complete. There will be quite a few errors, don't panic - this is normal.
You are now on what we coined "Psuedo-.181" - some weird hybrid of GB and ICS files. Your phone will not boot at this point.
- Open the unstick ICS tool
- Choose the newest (.20X) kernel
- Let it install, and reboot.
Because of this kernel upgrade, you are now able to flash ICS again... even a later version.
- Turn your phone off
- Hold VOL DOWN + VOL UP + PWR, then use VOL DWN to go to "Recovery" and VOL UP to select it
- Press VOL DWN + VOL UP to bring up the menu
- Navigate to "Apply update from external SD"
- Select the .20X zip file you downloaded.
- *IF IT FAILS THE FIRST TIME, TRY THIS PARAGRAPH AGAIN*
And now you're on the new ICS!
If you want root afterwards:
- Turn on your phone and let it boot normally
- Set everything up, and then turn on USB debugging
- Turn off your phone
- Hold VOL DWN + PWR to boot into AP Fastboot mode again
- Open the UnstickICS tool on your computer again
- Install the .85 kernel
- Turn your phone off
- Hold VOL DWN + VOL UP + PWR, then use VOL DWN to navigate to BP Tools, and VOL UP to select it
- Your phone should boot normally.
- Open the Droid Razr Utility 1.6 and select Root ICS.
- Follow the onscreen directions, pressing a button when it finishes rebooting, 3x.
- Turn your phone off again.
- Hold VOL DWN + PWR to boot into AP Fastboot again
- Use UnstickICS to flash the kernel of the version you want to upgrade to again
- Reboot
You need to do this, because the 4.0.4 kernel is not vulnerable to any root exploits. Going back to a previous kernel (in this case, 4.0.3) will allow you to exploit and obtain root, and then upgrade back to 4.0.4.
If you have any questions, I'll be glad to help.
wOw
Wicked dude.
Enviado de meu XT910 usando o Tapatalk 2
__________________
Just follow these instructions if anyone is bricked.
I see this kind of post a lot. People need to read warnings :/
Aliceics said:
I see this kind of post a lot. People need to read warnings :/
Click to expand...
Click to collapse
I am also wondering why there are so many threads like this even each posted leak is marked that here is no way back to 2.3.6. with many exclamation marks....
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
ergotelis said:
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
Click to expand...
Click to collapse
You'll probably need to flash a new recovery partition. Check out this thread:
http://forum.xda-developers.com/showthread.php?t=1950307
RaiderDuck said:
You'll probably need to flash a new recovery partition. Check out this thread:
http://forum.xda-developers.com/showthread.php?t=1950307
Click to expand...
Click to collapse
Thanks, but the problem is that this guy can get into the recovery with powering up+holding volume down button, if i understood well.but I can't!
ergotelis said:
Thanks, but the problem is that this guy can get into the recovery with powering up+holding volume down button, if i understood well.but I can't!
Click to expand...
Click to collapse
flasing a recovery is done via fastboot so you don't have to enter recovery but fastboot (hold power and volume down till it shows fastboot, then press up) .
look at this post: http://forum.xda-developers.com/showpost.php?p=33137046&postcount=10
Fix
ergotelis said:
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
Click to expand...
Click to collapse
hello i had this problem yesterday, it happens in neutrino rom to alot of people!
and btw i could not open recovery either
ill explain what i had to do
i had to use moto-fastboot and install a new recovery, basically your recovery is dead and your rom is unbootable
heres the steps
download the moto drivers and install
http://forum.xda-developers.com/attachment.php?attachmentid=1381183&d=1349549067
then download the motofastboot zip http://forum.xda-developers.com/attachment.php?attachmentid=1381414&d=1349555102
and create a new folder in C: (computer) called Android and then drag the files from the moto zip into android
Then download a new recovery http://www.mediafire.com/?6ww8wrjrdqq9m97
place the recovery.img into the android folder
now you have all the files needed to reflash your new recovery and fix your phone the whole idea is to reinstall recovery so you can access it and wipe and install the rom fresh again
now you need to do these steps
1) Attach your phone to the PC via USB (use a port closest to the power supply)
2) Reboot phone while holding volume down until you see "fastboot"
3) Press volume up to initiate fastboot
4) On your PC click the Start menu, then in the search box type "cmd"
5) In the command prompt type the following commands (no quotes, hit enter after each command)
6a) "cd c:/android"
6b) "moto-fastboot devices"
your CMD promt should show something like this
C:\Users\Me>cd c:/android
c:\Android>fastboot devices
TA20703SX9 fastboot
c:\Android>
now if that has all worked type the following phrases
moto-fastboot erase recovery
moto-fastboot flash recovery recovery-clockwork-6.0.1.4-maguro.img
moto-fastboot reboot
now the phone should reboot, unplug the usb and pull battery out.
put battery back in and then try to boot into recovery like you normally would (power button + Vol Down)
and your new recovery should load!
from here you can wipe your whole system which i would reccomended as your current one is corrupt and install a new rom or reflash your current on onto a clean wipe. if you dont understand how to clean wipe do all of these steps, factory reset, clear cache, clean dalvik cache then go to mounts > storage and format data + format cache + format system
now install new rom and let it boot up, should bootloop a couple of times then start! if not unplug battery from phone and ask for further assitance
Pixelguy said:
1) Attach your phone to the PC via USB (use a port closest to the power supply)
2) Reboot phone while holding volume down until you see "fastboot"
3) Press volume up to initiate fastboot
Click to expand...
Click to collapse
Thank you for your help, the problem is exactly here, i put on the usb, i power up the phone by pressing the volume down, and the phone does nothing,doesn't show the fastboot,and after 10-15 secs starts rebooting again. This is my problem!
The only response from my phone is when powering up, and pressing the volume up, it says "starting rsd protocol support"
Is there any case that my volume down is dead?
ergotelis said:
Thank you for your help, the problem is exactly here, i put on the usb, i power up the phone by pressing the volume down, and the phone does nothing,doesn't show the fastboot,and after 10-15 secs starts rebooting again. This is my problem!
The only response from my phone is when powering up, and pressing the volume up, it says "starting rsd protocol support"
Is there any case that my volume down is dead?
Click to expand...
Click to collapse
unplug usb
remove battery, then put battery back in make sure phone off (no green light)
then hold power button and vol down at the same time for a few seconds
Fastboot should appear in white writing then press up volume and it should say starting rsd protocal or something similiar
then plug in usb and follow the steps i have written above
i do exactly what you said, but doesn't show fastboot. from switched off, if i press volume up with power button, i see the message "starting rsd protocol support" .but no fastboot option!
Is there any chance that you can access adb after bootscreen? than you can use "adb reboot recovery" to get there...
jorno88 said:
Is there any chance that you can access adb after bootscreen? than you can use "adb reboot recovery" to get there...
Click to expand...
Click to collapse
When i start up phone, the only combination possible to stop restarting is by pressing power+vol up to show that with RSD. There is no other option then selectable. Power + volume down does not work, doesn't show anything, has anyone of you experienced this thing?
If the only working option you have is RSD, then I'm afraid you're stuck with having to flash a stock SBF. I hope you know/remember exactly what stock version you had installed before any modding or flashing, because the SBF has to match exactly. Choose wisely and read up as much as you can before flashing.
I have over a year now with custom roms, and i can't remember which version i had. Why do i have to find exactly the version that i had? The latest stock version won't work with rsd? It will make it hard brick?If i manage at least to recover the fastboot menus etc it would be great!
I will later also try to open it, to see if the side button "volume down" is not working,.
I have another question, in your moto atrix, if you press on startup power+vol up, are you also seeing the "starting RSD" etc option??
ergotelis said:
I have over a year now with custom roms, and i can't remember which version i had. Why do i have to find exactly the version that i had? The latest stock version won't work with rsd? It will make it hard brick?If i manage at least to recover the fastboot menus etc it would be great!
Click to expand...
Click to collapse
Yes, flashing a wrong SBF will most likely hardbrick your device.
ergotelis said:
I have another question, in your moto atrix, if you press on startup power+vol up, are you also seeing the "starting RSD" etc option??
Click to expand...
Click to collapse
Can't try right now, but as far as I know, yes, that is a standard way to enter RSD mode.
thank you, so, i know that at least my phone responds to some instructions.
Is there anyone else to suggest me to do anything else?
IN rsd mode, (other than flashing a stock random rom with chance of hardbricking,)the phone can be read by usb, can i do anything there?
ergotelis said:
IN rsd mode, (other than flashing a stock random rom with chance of hardbricking,)the phone can be read by usb, can i do anything there?
Click to expand...
Click to collapse
Sadly no. The RSD mode can only ever be used to flash SBFs. That's it. Nothing less, nothing more.
I will now try to open it to see if vol down is not working well. If it does work, i will select a stock rom 1 year old and i will flash it using rsd, and whatever happens....:good:
I disassembled the phone, the button seems to operate fine(?).
I flashed with RSDlite the 2.3.6 version, the RSD stuck to waiting for phone to restart.
The phone restarted, the "unlocked" logo disappeared.
Starts normally, passes the red motorola logo, shows the graphic of AT&T, and after ~10sec starts restarting again. Bootloop again!
At boot, pressing power+vol up, i can still get the RSD support. Pressing power+vol down does nothing, I don't see any error messages, like the ones in hard brick.
What can i do now, any ideas please!!!
try this
ergotelis said:
I disassembled the phone, the button seems to operate fine(?).
I flashed with RSDlite the 2.3.6 version, the RSD stuck to waiting for phone to restart.
The phone restarted, the "unlocked" logo disappeared.
Starts normally, passes the red motorola logo, shows the graphic of AT&T, and after ~10sec starts restarting again. Bootloop again!
At boot, pressing power+vol up, i can still get the RSD support. Pressing power+vol down does nothing, I don't see any error messages, like the ones in hard brick.
What can i do now, any ideas please!!!
Click to expand...
Click to collapse
Yesterday I had a hard time getting my phone into fastboot mode, after loading a bad SV kernel,it only wanted to start the RSD protocol mode. I eventually got into fastboot by plugging into the wall charger, then removing and installing the battery while holding the vol button. When fastboot appears, unplug the charger to allow sd access.
Thanks for the suggestion, i tried even this,it didn't work. The funny thing is that it shows the battery charging level full screen if i connect the charger, as it starts.
I noticed also that when i press vol down now, it takes longer to start and continue to the moving red logo, it stays for a while stable red,feels like it is thinking whether to start or not lol (if i don't press vol down, on the power up the red moto logo immediately starts the classic "waving" effects)
Anyone having any kind of suggestion?I guess you don't, right?
Good day all to you
I have the moto xt910, until this morning it was fine with 4.0.4 .
I downloaded 4.4.2 + gapps for it and prepared for updating. The xt910 is rooted, i backuped anything, i put CWM on it and then i began to boot into recovery mode. I backuped again and then did the steps I was adviced to: Wipe data/factory reset - wipe cache and then wipe dalvik cache.
After that I installed cm11 on it - everything was fine. then i needed to install the gapps stuff. i recognized i did not have it on my external sd-card so i put it the card out of the xt910 and copied that .zip from my pc to the sd-card. I put back the sd-card into the xt910, waited a minute and tried to access on it again to install gapps.... The Bootloader stucked, couldnt do anything at all, it disappeared. only option was "power+volumedown".
After this i just get the "moto logo-dualcore" sign for 10seconds, screen goes black and thats it - nothing happens.
Pressing power button - nothing happens at all. Pressing power+volumedown, the logo appears and screen goes black again, no bootloader or anything else (the screen looks like it is slightly lighted in black but absolutely nothing to do).
When i press power+volumedown and i release power when the screen flickers but still holding volumedown, it appears white font saying this:
"AP Fastboot Flash Mode (S) 0A.74 - eMMC Info: Size 16G - To return to normal mode - first press power key to power down - Device is LOCKED. Status Code: 0 - Battery OK, OK to Program, Connect USB, Data Cable"
I can press power, it goes off, I can press power, logo appears, still stuck in the same again as before . When connecting with usb it tries to install drivers, but it doesnt found anything ( Usb Driver is ok, all others failed to install)
Is the phone dead or can I somehow reset it again or make it work again?
Thanks to everyone and hope for your answers and help
Use RSD Lite to reflash your stock 4.0.4. Search for flashing with RSD Lite.
DROID RAZR with Tapatalk 4
neo.ank said:
Use RSD Lite to reflash your stock 4.0.4. Search for flashing with RSD Lite.
DROID RAZR with Tapatalk 4
Click to expand...
Click to collapse
Thanks for your help,
I already tried RSD Lite but it doesnt recognize the phone. How am I gonna do that?
I installed motorola device manager and it shows 4/5 driver ready. The one that wont work is "MTB-USB Driver"
Klicking on Motorola Device Manager it just tries to update but dont find anything, it says "Current Version: N/A"
(I havent seen those drivers before, when the phone worked the drivers were called somewhat else on computer)
csa85 said:
Thanks for your help,
I already tried RSD Lite but it doesnt recognize the phone. How am I gonna do that?
I installed motorola device manager and it shows 4/5 driver ready. The one that wont work is "MTB-USB Driver"
Klicking on Motorola Device Manager it just tries to update but dont find anything, it says "Current Version: N/A"
(I havent seen those drivers before, when the phone worked the drivers were called somewhat else on computer)
Click to expand...
Click to collapse
Try other usb port.
Turn of the phone,then turn it on,while it´s connected to usb.
If that doesn´t work,deinstall all motorola drivers,restart laptop (computer) and install them again.
And you must press vol- vol+ and power button to get to the AP Fasboot mode.
I have flashed my (now my father's) razr couple months ago and now GPS stopped working. It needs to be repaired.
I kind of know how to remove safestrap but what really annoys me is JBX kernel boot logo which appears whatever I do. I can be using stock rom and have no safestrap (nor other roms) installed but JBX logo still appears. I have never been really using it, just tested it once and since that, it is stil there.
Any idea how to remove it?
http://forum.xda-developers.com/showthread.php?t=2390645
Sent from my Razr XT910
Unfortunatelly those bootanimations are no longer available. Any other tips?
PL113 said:
I have flashed my (now my father's) razr couple months ago and now GPS stopped working. It needs to be repaired.
I kind of know how to remove safestrap but what really annoys me is JBX kernel boot logo which appears whatever I do. I can be using stock rom and have no safestrap (nor other roms) installed but JBX logo still appears. I have never been really using it, just tested it once and since that, it is stil there.
Any idea how to remove it?
Click to expand...
Click to collapse
You need a PC to do this and just a regular USB/Charging cord that you normally would use to connect it to a computer.
You need to RSD it, It'll erase everything on the Internal, not the SD card so that should be safe.
Here is a link for the RSD program. LINK
Here is a list of different versions of Android you can download for your Razr LINK
And you also will need these drivers here LINK
(skip this step if your stuck in a bootloop)
1. Now what you do is you connect your phone to the computer, I used Media (MTP) mode. Install the Drivers and install RSD lite. and pick your Fastboot file version you want, I did the 4.1.2 so i could root it again with the easy root, but its your preference. Now Unplug your phone and hold power and turn it off.
2. Now press Power and Vol DOWN together. if it doesn't do anything let go of power button but keep the Vol DOWN, It should come up with a menu. Let go of Vol DOWN and tap it until you get to the option that says RSD mode, then press Vol UP.
3. Connect your device to the computer. RSD Lite should show a device on slot 1. Click it then press START. now browse and find the fastboot files the click Decompress and flash.
4. DO NOT TOUCH THE PHONE. DO NOT TOUCH THE PHONE. DO NOT TOUCH THE PHONE. DO NOT TOUCH THE PHONE.... oh yeah, one more thing. DO NOT TOUCH THE PHONE!
5. After its done, VIOLA. Stock phone. Re-Root. Reinstall SafeStrap. golden!