I finally got my HTC programmed and working. Everything with it is great, except now it cannot connect to the internet.
I get two kinds of error messages- initially it kept telling me that my username or password was wrong..... I couldnt find a place to enter either of those [not that i knew what they should be anyway], and I've never had this problem on my other HTC's. Now its telling me that it cannot connect for an unknown reason and that i should change the settings if needed or reset the device according to manufacturer's documentation....
What should I do?
I upgraded to wm6.1 last night, and im running USCC as my carrier.
It was suggested to me that i enter ##778 mode and change some settings there, but i do not know the MSL for my area.
Any idea where to find that?
Thanks.
Not sure if these will work but found them when I was looking for my MSL.
Use this method. I don't know who found it, but credit goes to them.
Change the following registry entries in:
HKEY_LOCAL_MACHINE\SOFTWARE\HTC\ATDbgLog
Enable: 1
LogMode: 1
* Wait a about 10 minutes (more time will not hurt), and soft-reset.
* Check to see that the file \Atlog\ATDbg0.txt has been created.
* Return the values back to what they were (most likely 0) waiting the same amount of time as above.
* Look in the ATDbg0.txt file and you should see a log of commands sent to the CDMA radio and there should be something like this somewhere in the file:
~~~~~~~~~~~SNIP~~~~~~~~~~~~
00:00:00 Tx:AT+HTC_RMSL=0\r
00:00:00 Rx:+HTC_RMSL: (###THIS WILL BE THE MSL###)\r\n0\r
00:00:00 Tx:AT+HTC_ROTKSL=0\r
00:00:00 Rx:+HTC_ROTKSL: 123456\r\n0\r
~~~~~~~~~~~SNIP~~~~~~~~~~~~
The numbers next to the Rx: +HTC_RMSL line should be your MSL
OR
Do a search for BAFMSL. It's a universal SPC code finder tool.
It requires .net 3.5, and tends to fail randomly, but so far has worked on 8 of 10 phones I have tried it on.
BTC
http://www.rimweb.in/forums/index.php?showtopic=17301
=] Awesome. This is just what I needed. Thanks.
HTC MSL
I finally got my HTC programmed and working. Everything with it is great, except now it cannot connect to the internet.
I get two kinds of error messages- initially it kept telling me that my username or password was wrong..... I couldnt find a place to enter either of those [not that i knew what they should be anyway], and I've never had this problem on my other HTC's. Now its telling me that it cannot connect for an unknown reason and that i should change the settings if needed or reset the device according to manufacturer's documentation....
What should I do?
I upgraded to wm6.1 last night, and im running USCC as my carrier.
It was suggested to me that i enter ##778 mode and change some settings there, but i do not know the MSL for my area.
Any idea where to find that?
Thanks.
Last edited by MysticThunder; Today at 01:38 AM.. Reason: new title.
Should be as simple as 000000. Same as Verizon...I just did mine, hope it works....KC
On my Titan all I did after upgrading the rom was create a new connection, called it broadband, entered #777 as the number, and my phone number followed by @vzw3g (password blank, check save password) and it worked fine.
MysticThunder said:
I finally got my HTC programmed and working. Everything with it is great, except now it cannot connect to the internet.
I get two kinds of error messages- initially it kept telling me that my username or password was wrong..... I couldnt find a place to enter either of those [not that i knew what they should be anyway], and I've never had this problem on my other HTC's. Now its telling me that it cannot connect for an unknown reason and that i should change the settings if needed or reset the device according to manufacturer's documentation....
What should I do?
I upgraded to wm6.1 last night, and im running USCC as my carrier.
It was suggested to me that i enter ##778 mode and change some settings there, but i do not know the MSL for my area.
Any idea where to find that?
Thanks.
Click to expand...
Click to collapse
there are a few settings in you need to make sure are corect in the m ip settings of the phone after u press ##778. I am using uscc and had the same issue. so I know this to be a factor after updating roms. Below are the correct settings for your m ip
Number of Profiles : 6
Active User Profile Index : 0
MIP_MODE : Mobile IP Prefered
MIP Registration Retries : 1
MIP Registration Retry Timeout : 2000 ms
MIP Pre-Registration Timeout : 3
Mobile Node-HA Authentication : Enable
Send a Registration Request Only in Use : Enable
Dormant Hanfoff Optimization: Enable
I cant stress enough... these need to be exact with uscc... dont forget to run the uscc carier cab.
If you want to have EVDO when it comes to your areas as well, under Security Settings, make sure the HDR username is your [email protected], and the ESN is in hex and all capital letters. The HDR Password is your ESN the same as above but no @uscc.net on the end.
Below this screen is also the ppp username and password, they should be your phone#@uscc.net and your phone # as the password.
These 2 settings are also necessary for data to work correctly.
BTC
Hey guys i just bought a mogul on ebay and had it flashed to metro pcs, the internet, and gps work fine, i just cant get it send out mms like many of ur phones can, i dont have sprint picture mail, because i have metro service.
ANY HELP WILL BE GREATLY APPERICATED!!!!!
Did you install Arcsoft? If you did not, you might want to find a copy of it to intall on your phone.
Once you do, follow the directions below as a guideline.
Remove/Uninstall any existing MMS composer you have attempted to setup. Also a good idea to remove any registry keys it may have created that are left behind after the uninstall.
1: Install Arcsoft MMS version 5.0.70.24
2: Open your Messaging and click on the SMS/MMS option.
3: Click on "Menu" and select "MMS Options" then select the "Servers" tab.
4: Add a new server with the following settings:
Server Name: metropcs
Gateway: wap.metropcs.net
Port number: 3128
Server address: http://mms.metropcs.net:3128/mmsc
Connect via: SELECT EITHER THE CONNECTION YOU SETUP ABOVE OR "The internet"
Send limit: 399K
5: Click "Done" and then set the new server as default.
6: Using a Registry Editor edit the following values:
[HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\ArcSoft MMS UA\Config\mm1\WspHeader]
DELETE KEY -> "X-VzW-MDN"
ADD STRING -> "X-metropcs-MDN"="XXXXXXXXXX" ( Insert your 10 digit phone Number )
ADD STRING -> "X-DEVICE-MIN"="1XXXXXXXXXX" ( Insert your 10 digit phone Number WITH the 1 in front of it )
Hope this helps nobale Metro PCS cousin...8)
*P.S.-- You might also want to find the Titan MMS fix CAB by CRwinger to help keep your MMS working properly. The reason is that when you open PIE it creates a registry key that will stop you from send/recieving MMS. The CAB file will automatically delete that file by pressing the messaging hard button on the top left of your Mogul.
Other alternative is not to use PIE and just use Opera.
PM me if you need any help, I'm with Cricket so we are almost in the same boat. 8)
mougl flashed to metro, mms problems
i'm really not smart when it comes to computers and pda, what is a pie and what is opera?
I'm pretty sure that PIE is something internet explorer. Opera is a mobile web browser. Probably one of the best since you can get youtube
mogul flash to metro, mms problem
ok i've located arcsoft mms 5.0.70.24, which on this forum, one do i download because i see beta and several other versions.
I use 5.0.31.19 myself. Any version after that or a beta is fine really. Its a trial and error of how well the software version you have works like you want it to.
Just DL anyone of them.
*Important--If anything back-up your phone just incase you need to do a hard reset. Use a program called PimBackup...its free.
As paintballinfl said:
PIE=Pocket Internet Explorer
Opera= A new browser for PDA's to view websites as if you are actually at your desktop.
mogul flashed to metro, problem with mms.
thanks, i had downloaded a older version, how do i delete the older program completely? i removed it from my phone but, what's a registry edit? and how do i do that before installing the new arcsoft?
You need to find phmReg Edit and use that program to do your registry edits...its free just google it.
Also if you already have a version of arcsoft installed use the guide to get MMS working for you on Metro PCS. If that version doesn't work for you do the advised below.
*If you want to change the version of arcsoft it is best to start from scratch and hard reset the device. Thats why i suggested you to do a back-up your phone. Also if a hard reset is needed please be careful because it will erase everything on the phone except the SD card.
So it goes like this:
install phmReg Edit-->install Arcsoft-->follow steps in guide
mogul flashed to metro pcs, mms problem.
THANK YOU GUYS... i'm able to send and receive picture and video mail, i just gotta get the titian cab fix or install opera, to keep it up.. what's the best opera version to install?
There are many builds out there but Opera build 2392 is good...seems to make it the default browser instead of PIE.
For example: When clicking on a link in a text message, Opera will open instead of PIE.
The Titan MMS fix by CRwinger I believe you might be able to find on PPCgeeks.
mogul flashed to metropcs, mms problems
Is it the mms cab fix for cricket? because i found that one, it was a choice between that one that the vougue fix. and if i choose the cricket fix will i have to redo all the setting back to metropcs? any link to the titian mms fix cab would be appreciated greatly!!! THANKS
hey where can i find the right one Install Arcsoft MMS version 5.0.70.24 for metro because it has different type of them like verzion and alltell etc.. which one is the best.....please help me
Hi everyone, PLEASE READ PLEASE READ STEP BY STEP i was reading and a lot of people have questions about going to metropcs and nobody give them really good help, so i decided to make this post for you guys but please please do not post me asking how to do it in other htcs phone or worst in samsungs, lgs, etc etc I AM DOING IT THIS ONLY FOR HTC RAPHAEL or 6850 or touch pro cdma what ever you want to call it. ok so lets get start it. you have either two options:
1. Install the Hard-SPL (to unlock the phone), Install custom radio, Install custom rom, Install and modify files to make it work in Metropcs internet,mms etc. and finally take it to metropcs pay between $40 to $60 box so they flash it and you have already the phone working with everything. (recommened for dummies)
2. Install the Hard-SPL (to unlock the phone),Install custom radio Install custom rom, Install and modify files to make it work in Metropcs internet,mms etc. and Flash the HTC 6850 Touch Pro MEID and ESN to Clone the phone (i assume you have one phone already working on metropcs and you dont want to use the phone anymore so you clone it hehehehe.
--------------------------------------------------------------------------
1.Option. Download this file first:
http://www.4shared.com/file/140639926/7fa190d6/TP_ESN_FILES2.html
Important:
first, if you have GSM Touch Pro/Raphael (NOT CDMA, NOT SPRINT/VERIZON/ALLTEL/TELUS/BELL), this will brick your device.
to download a compatible hardspl package for gsm touch pro you can go to forum.xda-developers.com.
but if you have CDMA Touch Pro/Raphael, then you have to use this hardspl, not the one at xda-developers!!!
preparations before flash:
1) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
2) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
3) now decide which Hard-SPL you want to flash. if you have Verizon, flash VZW package (from verizon attachment). if you have Sprint, Telus or Alltel or Bell, flash default package (Raphael_CDMA_HSPL_037.zip).
instructions:
1) extract Hard-SPL Raphael_CDMA_HSPL_037.zip
2) you must Have Phone Synced with PC in Windows Mobile!
3) run HardSPL exe that you extracted before.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 0.37.C-SSPL or for Verizon devices it should say 0.35-C-SSPL.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.37.CMONEX MFG.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
make sure to get SSPL-Manual specifically for Verizon phones from the verizon package.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL.
NOTE 5: use Relocker *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. Default relocker is for Sprint etc, Raphael_CDMA_VZW_Relocker in the verizon package is for Verizon touch pro's.
(Please Donate to the CDMA Raphael Project Team - http://shorl.com/frastijeketrebo - Thanks!! )/ source
Next.Next.
we need to install the Radio, (make sure the phone is recognized by microsoft sync) i relized that the better one out there for metropcs is Telus v1.04.05V thats why i put it in my rar file.
1. extract Telus v1.04.05V and run ROMUpdateUtility
2. install it
3. when is done make sure the radio is v1.04.05V (in the dilaler press menu then press phone information and look for Radio.)
Next.
Install the rom of your chooise.I recommend for metropcs either mightyrom
(http://forum.ppcgeeks.com/showthread.php?t=52695) or NFSFAN's Custom WM6.5 ROMs (http://forum.xda-developers.com/showthread.php?t=516509) a lot of people ask for a custom rom for metropcs and thats not necesary to have almost every raphael cdma rom out there is compatible with metropcs.
-Elite Rom RC1 choose telus
http://forum.ppcgeeks.com/showthread.php?t=72401
-NFSFAN's Custom WM6.5 ROMs.
http://forum.xda-developers.com/showthread.php?t=516509
-www.MightyROM.com
http://forum.ppcgeeks.com/showthread.php?t=52695
-HAZE V1.6 Native 6.5 Kernel.
http://forum.xda-developers.com/showthread.php?t=561931
-Reflectionist Rom V0.6
http://forum.xda-developers.com/showthread.php?t=562337
-Black Dragon Titanium Rom 23420
http://forum.xda-developers.com/showthread.php?t=547846
-alpha build 1.5
http://forum.xda-developers.com/showthread.php?t=559640
-JUICY 8
http://forum.xda-developers.com/showthread.php?t=518466
-WM 6.5 21501 djbeames
http://forum.xda-developers.com/showthread.php?t=509544
-grooveROM 5
http://forum.xda-developers.com/showthread.php?t=534888
-EnergyROM 'Photon'
http://forum.ppcgeeks.com/showthread.php?t=69545
-Calkulin's Visual
http://forum.ppcgeeks.com/showthread.php?t=87040
-MurdaROM
http://forum.ppcgeeks.com/showthread.php?t=87040
-SsS-ROMv0402
http://forum.ppcgeeks.com/showthread.php?t=68755
-NK-All Carriers-RZ Baseline 3.2
http://forum.ppcgeeks.com/showthread.php?t=81038
-Demolition 6.5
http://forum.ppcgeeks.com/showthread.php?t=66799
-Psyki 4
http://forum.ppcgeeks.com/showthread.php?t=66993
-JD's Clean
http://forum.ppcgeeks.com/showthread.php?t=73860
-Sac ROM
http://forum.ppcgeeks.com/showthread.php?t=68734
-SilenceROM
http://forum.ppcgeeks.com/showthread.php?t=84859
-eRice
http://forum.ppcgeeks.com/showthread.php?t=46965
-MERDIN'S WMPro
http://forum.ppcgeeks.com/showthread.php?t=50716
-StarROM 2.0
http://forum.ppcgeeks.com/forumdisplay.php?f=68&order=desc&page=2
-TruXt v5.1
http://forum.ppcgeeks.com/showthread.php?t=82653
-Chaos ROM
http://forum.ppcgeeks.com/showthread.php?t=75974
-Longhorn ROM
http://forum.ppcgeeks.com/showthread.php?t=65849
-Sceptre Rom 3.4 SenseSuite
http://forum.ppcgeeks.com/showthread.php?t=75215
-dcd's hermann ROM 2.00
http://forum.ppcgeeks.com/showthread.php?t=69754
-091409 XOR
http://forum.ppcgeeks.com/showthread.php?t=84394
-CFAY 1.5.5
http://forum.ppcgeeks.com/showthread.php?t=50471
-Juggalo TP ROM v0.08B (choose telus)
http://forum.ppcgeeks.com/showthread.php?t=49341
-JonRom Version 2.55
http://forum.ppcgeeks.com/showthread.php?t=79924
-FuzeBerry II
http://forum.ppcgeeks.com/showthread.php?t=62786
-midNIGHT v5.5
http://forum.ppcgeeks.com/showthread.php?t=75032
-Copper v.0.0.0.1
http://forum.ppcgeeks.com/showthread.php?t=64242
-Ivan's ROM 1.9.S.V
http://forum.ppcgeeks.com/showthread.php?t=48463
-dB_ROM WM 6.5
http://forum.ppcgeeks.com/showthread.php?t=67426
-FALLEN ROM
http://forum.ppcgeeks.com/showthread.php?t=63479
-Yay 4 Juggs
http://forum.ppcgeeks.com/showthread.php?t=61274
-Jmz Rom 3.0
http://forum.ppcgeeks.com/showthread.php?t=61953
-FireROM
http://forum.ppcgeeks.com/showthread.php?t=73395
-KK's Loaded ROM v1.8
http://forum.ppcgeeks.com/showthread.php?t=52307
-Tech1 MultiMedia
http://forum.ppcgeeks.com/showthread.php?t=72782
-JOKER ROM
http://forum.ppcgeeks.com/showthread.php?t=68213
-DREAM Full and Lite
http://forum.ppcgeeks.com/showthread.php?t=49338
-THE LAST-Forgiven
http://forum.ppcgeeks.com/showthread.php?t=70059
-NSFW College ROM
http://forum.ppcgeeks.com/showthread.php?t=69371
-PhantomROM
http://forum.ppcgeeks.com/showthread.php?t=62796
-JowPod
http://forum.ppcgeeks.com/showthread.php?t=69269
-Merdin's
http://forum.ppcgeeks.com/showthread.php?t=59780
-PsykiROM v1.0
http://forum.ppcgeeks.com/showthread.php?t=65145
-nueROM-S
http://forum.ppcgeeks.com/showthread.php?t=42777
i think thats it if you know another one just let me know i will post it.
Finally the most difficult part in this process.
set up the internet, mms and GPS
download this file:
http://www.4shared.com/file/140658132/5838a6f3/MetroPCS.html
-connect your phone to de pc and install get spc in the phone
-run it and press on get spc, press ok or yes and it will display six digit number write this number down because we will need it.
-in the dialer type ##778# click on edit and write the six digit number that you wrote down.
-next a screen that says EPST and below that say Display will appear.
-we well need to modify some of this ones
DISPLAY
-NAM NAME write you ten digit numer
-SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that)
-MSID write your ten digit phone number
click in view info and go to
NAM SETTINGS
-NAM NAME write your ten digit phone number
-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516
-MIN2 first three digits of your phone number (area code)
-MSID write your ten digit phone number
-MCC 310
-MNC 27
-NMSI 27and write your ten digit phone number
-IMSI 31027and write your ten digit phone number
Part 2
click in view info and go to
CDMA SETTINGS
-A-SYS PRIMARY 283
-B-SYS-PRIMARY 384
-A SYS-SECUNDARY 691
-A SYS-SECUNDARY 777
-MON_TERM_FOR_HOME ENABLE
-MON_TERM_FOR_SID ENABLE
-MON_TERM_FOR_NID ENABLE
-EVRC ENABLED DISABLED
-HOME PAGE VOICE 13K
-HOME ORIG VOICE 13K
-ROAM ORIG VOICE 13K
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535
click in view info and go to
MODEM SETTINGS
-SLOT CYCLE 1
-PREFERRED SERVING AUTO
-PREFERRED MODE AUTO
-HDR HYBRID ENABLE
-CLEAR ALL MRU NO
click in view info and go to
-PRL
-UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE
click in view info and go to
SECURITY
-HDR AN AUTH USER ID [email protected]
-HDR AN AUTH PASS metropcs
-PPP USER ID [email protected]
-PPP PASS metropcs
click in view info and go to
DATA PARAMETERS
-PACKET DIAL #777
click in view info and go to
M.IP SETTINGS
-NUMBER OF PROFILES 6
-ACTIVE USER PROFILE 0
-MIP_MODE SIMPLE IP ONLY
-MIP REGISTRATION RETRIES 1
-MIP REGISTRATION RETRY 2000 ms
-MIP PRE-REGISTRATION TI 30
-MOBILE NODE-HA Disable
-SEND A REGISTRATION Enable
-DORMAND HANDOFF Disable
click in view info and go to
M.IP DEFAULT PROFILE
-ENABLE PROFILE Enable
-NAI [email protected]
-MN HA SPI SET Disable
-MN HA SPI VALUE 0
-MN AAA SPI SET Disable
-MN AAA SPI VALUE 0
-HOME ADRESS 0.0.0.0
-PRIMARY HA ADDRESS 255.255.255.255
-SECUNDARY HA ADDRESS 255.255.255.255
-HA SHARED SECRET metropcs
-AAA SHARED SECRET metropcs
-DMU 0
-MN 0
make sure that
M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable
click menu ok and reset.
when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROPCS.CAB
also after everything is done please dont forget to take the phone to metropcs so they can put you nam in the metropcs system thats what they call flash the phone to metropc.
Internet Sharing - tethering big thanks to silvaadams from ppcgeeks
make sure you have internet on your phone ofcourse
start up comm manager and click your internet sharing button thingy lol
click connect on the lower left hand corner
wait for phone to say check usb connection
then connect phone to usb and usb to computer (should say connected)
open internet explorer
go to settungs
go to internet options
go to connections tab
click on lan settings
click proxy server check use proxy blabla
then type wap.metropcs.net port 3128
then ok
open up firefox
once open go to tools> options> advanced> network
under network click settings
select manual proxy config
under http proxy type
wap.metropcs.net [port:] 3128
then check off "use this proxy server for all protocols"
--------------------------------------------------------------------------------------------------------------------------------------------
2.option. HTC 6850 Touch Pro change MEID change ESN Repair / Clone Solution i assume you have a phone already in metropcs so u can clone it and avoide paying $40 or $50 dollars activation fee.
Download this file first:
http://www.4shared.com/file/140639926/7fa190d6/TP_ESN_FILES2.html
PLEASE READ SOME DIFFERENCES FROM OPTION 1.
Important:
first, if you have GSM Touch Pro/Raphael (NOT CDMA, NOT SPRINT/VERIZON/ALLTEL/TELUS/BELL), this will brick your device.
to download a compatible hardspl package for gsm touch pro you can go to forum.xda-developers.com.
but if you have CDMA Touch Pro/Raphael, then you have to use this hardspl, not the one at xda-developers!!!
preparations before flash:
1) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
2) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
3) now decide which Hard-SPL you want to flash. if you have Verizon, flash VZW package (from verizon attachment). if you have Sprint, Telus or Alltel or Bell, flash default package (Raphael_CDMA_HSPL_025_MFG).
instructions:
1) extract Hard-SPL Raphael_CDMA_HSPL_025_MFG
2) you must Have Phone Synced with PC in Windows Mobile!
3) run HardSPL exe that you extracted before.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) it should go to tricolour screen now and say 0.25.C-SSPL or for Verizon devices it should say 0.35-C-SSPL.
6) SPL flashes, device automatically reboots, job done.
7) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.25.CMONEX MFG.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter bootloader mode to see version: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
NOTE 2: anyone having problems with the device entering SSPL automatically, please copy SSPLManual.exe from the SSPLManual.zip attachment to the device and run it. then once the screen is in SSPL, run RUU manually. i.e. you run the RUU on the PC, if it isn't obvious.
make sure to get SSPL-Manual specifically for Verizon phones from the verizon package.
NOTE 3: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection, if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package is also available here.
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL.
NOTE 5: use Relocker *only* if you need to return the phone for warranty. only use it as last step - after reflashing stock OS and radio. Default relocker is for Sprint etc, Raphael_CDMA_VZW_Relocker in the verizon package is for Verizon touch pro's.
(Please Donate to the CDMA Raphael Project Team - http://shorl.com/frastijeketrebo - Thanks!! )/ source
-install the radio that is on TP ESN FILES2\RAPHING
-install the rom of your choise from Option 1
-now MAKE SURE YOU WRITE DOWN OR BACK UP ALL YOUR DATA SETTINGS BEFORE YOU DO THIS JUST IN CASE
- download
http://www.4shared.com/file/140658132/5838a6f3/MetroPCS.html
- install WModem_Driver_Installer_v1.2.2.4_WWE
-make sure to install get spc on the phone run it and get ur spc code
-disconnect phone
-put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc
-now install all the drivers but maybe it will tell that u need qcmdmxp or another one so just select files from Program Files\HTC\WModem_Installer\WinXp
-Disable USB connection in Active Sync by unchecking checkbox in Connection Settings of Active Sync
-Hold Pwr and Vol Down buttons and push reset button to boot the phone in bootloader mode.
Part 3
-Run mtty.exe from TP ESN FILES2
-Leave every setting alone apart from change the 'Port' to 'USB' in yhe drop down box. Hit OK.
In the window that opens up, type the following commands (All Commands are case Sensitive) Hit enter after typing each one. You may see nothing while typing, just type carefully.
1. rtask a
12 echo_on
3. readCID
4. writeCID 00000000
5. readCID (window should return CID as 00000000)
6. rtask c (will probably give and error - mine did!)
-Soft reset phone and close mtty.
-Re-enable USB connection in connection settings of ActiveSync. Make sure phone is 'connected' to ActiveSync, you might have to unplug and plug in usb to make this happen.
-Flash phone with Raphael_CDMA_HSPL_037.exe
-Let phone restart.
-disconnect phone
-put phone in diag mode (dial ##3424#) wait until the white screen disapear and connect your phone to ur pc
-download http://rapidshare.com/files/210789608/QPST_2.7.323__2008-09-19_.rar
-open QPST configuration and click on add port
-make sure to memorize the port that says htc diagnostic that port com is really important we well use it for many things
-Launch DFS. from TP ESN FILES2
-Select your phone's com port. (top left ish) this is the port that i was talking about diagnostic port com
-Select 6950 from the HTC devices menu on the left. Before you all start, yes I know we are programming a 6850, but the secret here is that the MEID portion of the 6850 equipment file in DFS ties up to the MEID locations in the radio rom supplied (which was ported from the diamond)
-Ignore any errors at the bottom of the screen about equipment not found etc... Remember, just follow the instructions!! So, once the com port is connected, go the MEID section and type your originial metropcs phone the one you have to clone MEID(D)(decimal) it should be on the back of the phone also make sure that the original metropcs phone os turn off u dont want to turn this phone ever in your life. Ignore the pESN that it creates but do not modify it
-Click Write like 4 times and it will write it to the phone no matter what it says at the bottom of the screen.
-Close DFS and soft reset.
-now go to http://www.previo.net/meid-esn-converter.html
-type your MEID(D)(decimal) and click submit the important thing here is ESN the hex not the dec. so copy the hex one.
-Go into diag mode ##3424# again wait untill the white screen disappear and connect it usb to ur pc
-Open up the attached CDMA Workshop 2.7 cdma workshop.exe but the one is in METROPCS.RAR not the one is in TP ESN FILES2 and select the com port to connect your phone. THIS COM PORT IS THE DIAGNOSTIC PORT.
-click connect and then read
-in your phone go to dialer and type ##778# edit and type your spc code then.
-Go to the security tab in workshop and click read by the esn. It should display your current esn.
-Type the esn that the website give you the hex one. this should be your original metropcs nam number
-click write.
-Go to Nam tap and Click in Banner
-Type MetroPCS and
-click write
-now Close CDMA WS and soft reset
-now install the radio u want to use from here
http://forum.xda-developers.com/showthread.php?t=531134&highlight=radio
recommend TELUS v1.04.05V or VERIZON v1.03.03V
-when is done type in your dialer ##778# edit in the screen that says EPST and below that say Display will appear.
-we well need to modify some of this ones
DISPLAY
-NAM NAME write you ten digit numer
-SCM write the first two digit of area code of the phone number(if appears to be editable if not leave it like that)
-MSID write your ten digit phone number
click in view info and go to
NAM SETTINGS
-NAM NAME write your ten digit phone number
-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516
-MIN2 first three digits of your phone number (area code)
-MSID write your ten digit phone number
-MCC 310
-MNC 27
-NMSI 27and write your ten digit phone number
-IMSI 31027and write your ten digit phone number
click in view info and go to
CDMA SETTINGS
-A-SYS PRIMARY 283
-B-SYS-PRIMARY 384
-A SYS-SECUNDARY 691
-A SYS-SECUNDARY 777
-MON_TERM_FOR_HOME ENABLE
-MON_TERM_FOR_SID ENABLE
-MON_TERM_FOR_NID ENABLE
-EVRC ENABLED DISABLED
-HOME PAGE VOICE 13K
-HOME ORIG VOICE 13K
-ROAM ORIG VOICE 13K
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535
click in view info and go to
MODEM SETTINGS
-SLOT CYCLE 1
-PREFERRED SERVING AUTO
-PREFERRED MODE AUTO
-HDR HYBRID ENABLE
-CLEAR ALL MRU NO
click in view info and go to
-PRL
-UPDATE PRL FILE AND YOU HAVE TO TRANSER THE FILE 02001 THAT IS IN METROPCS.RAR AND SELECT THAT ONE
click in view info and go to
SECURITY
-HDR AN AUTH USER ID [email protected]
-HDR AN AUTH PASS metropcs
-PPP USER ID [email protected]
-PPP PASS metropcs
click in view info and go to
DATA PARAMETERS
-PACKET DIAL #777
click in view info and go to
M.IP SETTINGS
-NUMBER OF PROFILES 6
-ACTIVE USER PROFILE 0
-MIP_MODE SIMPLE IP ONLY
-MIP REGISTRATION RETRIES 1
-MIP REGISTRATION RETRY 2000 ms
-MIP PRE-REGISTRATION TI 30
-MOBILE NODE-HA Disable
-SEND A REGISTRATION Enable
-DORMAND HANDOFF Disable
click in view info and go to
M.IP DEFAULT PROFILE
-ENABLE PROFILE Enable
-NAI [email protected]
-MN HA SPI SET Disable
-MN HA SPI VALUE 0
-MN AAA SPI SET Disable
-MN AAA SPI VALUE 0
-HOME ADRESS 0.0.0.0
-PRIMARY HA ADDRESS 255.255.255.255
-SECUNDARY HA ADDRESS 255.255.255.255
-HA SHARED SECRET metropcs
-AAA SHARED SECRET metropcs
-DMU 0
-MN 0
make sure that
M.IP CUSTOMER PROFILE 1,2,3,4,5,6 are Disable
click menu ok and reset.
when the phone resets please install Metro WAP and Arcsoft 5_0_70_24 from METROPCS.CAB
reset it one more time
finally call *228 wait untill the spanish thing is over and press 1 then wait 2 seconds press 1 again wait 2 seconds and press 1 again this will make u talk to custumer service tell them u are having trubles with ur phone and you need to reprogram your phone sometimes they are lazys and dont want to do it so insinst. please give them your MEID(D) decimal number and depend of your phone they will tell you do this or do that but dont do it write everything down and tell them yes ok i done hahaha in my case of kyocera melo they told me to do this type 111111 go to options service go to program 587846 type mdn MYPHONENUMBER type min 3234764516 and type home sid 6503 after that they told me im done just soft reset it and that its but when i hang up i didn do it and please dont do it go to dialer and type ##778# edit and we need to make some changes.
DISPLAY
-NAM NAME write the program number they give u my case 587846
-SCM write 58
click in view info and go to
NAM SETTINGS
-NAM NAME write the program number they give u my case 587846-MOBILE DIRECTORY NUMBER write your ten digit number
-MIN1 4764516 type the min number they give in my case 3234764516 323 is the area code but when u restar the phone this dissapear
click in view info and go to
HOME SID/NID
-HOME SID/NID #1 6503/65535 here just change the the SID for the one they give you my case 6503 the other one leave it as 65535
soft reset and you are ready to go.
Internet Sharing - tethering big thanks to silvaadams from ppcgeeks
make sure you have internet on your phone ofcourse
start up comm manager and click your internet sharing button thingy lol
click connect on the lower left hand corner
wait for phone to say check usb connection
then connect phone to usb and usb to computer (should say connected)
open internet explorer
go to settungs
go to internet options
go to connections tab
click on lan settings
click proxy server check use proxy blabla
then type wap.metropcs.net port 3128
then ok
open up firefox
once open go to tools> options> advanced> network
under network click settings
select manual proxy config
under http proxy type
wap.metropcs.net [port:] 3128
then check off "use this proxy server for all protocols"
thanks to englishdan from mobile-files.com, xda forum, cmonex, and everybody that makes this possible. also i download the files and i forgot most of the post that i got the files so please all the people that makes this files and aport to this excuse me for that my apologize i just want to make this easier to everybody becasue i spend days and days trying to do this thanks to the users from PPCGeeks, howardforums, and mobile-files. without this it wouldnt be possible to make this also my apologize if there is things from other forums not mentioned but i forgot most of the places and users that take infotmation off once again thank u.
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
hey bro
dude i work my ass off to get this work for 7 days sleeping only 3 or 4 hours i put all this info togheter four you guys and then u re telling me this, no where u will find this and i post at the last thanks to the guy who help me the most but if you go to his profile and see the post http://www.mobile-files.com/forum/showthread.php?t=111584 u will see how empty is a lor of questions and a lot of people that are confused but if you look what i write is so complete that everybody will understand there is a lot of people that i have to thanks but if i write all the names down there will be no space in the forum read bro and i thanks to all of them i mention at the end so please shut the **** off because i work my ass off to make this post.
snail813 said:
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
Click to expand...
Click to collapse
Great Job Looser
First post...yeah! Something tells me you're like one of those off duty english teachers: cite your sources.... Suck a fat one. Drey did an excellent job trying to help others and not himself. He doesn't even have a paypal link on the bottom of the posting. I have my TouchPro on metropcs fully functioning from multiple links on ppcgeeks and xda-developers. Thanks to many.
Drey, You did great with this post man! Too bad an off duty buttwhole is around fouling things up! What a jerk off. First post! lol.
snail813 said:
wow. this is my first post, and its a shame it had to be a reply to this post.
Where is the credit to the people who worked very hard on this stuff? no props to anyone at all.. not even another site.. so you expect to get all kinds of props for someone else's work? its pretty sad. and i hope you get your props.
-1
Click to expand...
Click to collapse
Metro WAP
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
belalucf said:
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
Click to expand...
Click to collapse
If you had the phone flashed to metropcs all you have to do is input the Metro WAP settings. I did not use a cab file. First HardSPL, Archsoft MMS, then change WAP settings, and the registry.
wap
Yeah I tried inputting all the settings, then creating a new connection called metro pcs with all the port settings and stuff, which I don't even see on this guide. Because if you don't create a new connection, it wont do anything once I removed the sprint connection which I did by changing the guardian file, which allowed me to even remove it. But I was hoping that this program would I guess populate that stuff somehow, so I went through and manually put in all those settings. Still no connection
ok
ok you can do it this way put your phone in dial mode ##3424# wait until white screen turns off and open workshop 2.7 from mteropcs.rar you have to go other tab under PRL choose write and select the ppl file
when you open the browser a window will apear you have to write your [email protected] and metropcs as password
note u set this up ##778# edit Mip default profile thank u
belalucf said:
It wont let me install the metro wap, I had the phone flashed to metro pcs first, when I did the step where you had to browse to find the prl file, it wouldn't show it, so I didn't do that part, so I installed the metro wap thing to the phone and installed and the phone says they cannot be installed after it tries to install for a little! Help me pleeeaasse!
Click to expand...
Click to collapse
thanks bro
thanks bro for me was hard i have to go to so many forums and read and read to make this work for my little brother, i gave him this phone as a gift but in sprint and he have metropcs so i decided to read and find out how this works and after work my ass off for 1 week taking information from here there ask so many questions i decided to make all that info in one post and then this jerk tell me this bro i am doing this to help everybody the important thing here is share so other people can learn and not like me that spend hours in my pc trying to figure this out thanks bro..
stukes said:
First post...yeah! Something tells me you're like one of those off duty english teachers: cite your sources.... Suck a fat one. Drey did an excellent job trying to help others and not himself. He doesn't even have a paypal link on the bottom of the posting. I have my TouchPro on metropcs fully functioning from multiple links on ppcgeeks and xda-developers. Thanks to many.
Drey, You did great with this post man! Too bad an off duty buttwhole is around fouling things up! What a jerk off. First post! lol.
Click to expand...
Click to collapse
mmm
if the cab file that i gave u (THANKS TO RYANMONGUL6800)didnt work try to do it manually http://rferreira1.googlepages.com/revisedMogul6800tometro.pdf if stills not working try to start again first install the cab file then go to ##778# edit ur spc code then edit mip. default profile for the one i have soft reset open browser it should ask for the username [email protected] and pass metropcs if still not owrking u have to follow this
from ryanmongul6800
Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the password below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
Click view info and pick MIP Default Profile, Enable profile should be ENABLE, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 255.255.255.255, secondary should be 255.255.255.255, HA shared secret and AAA secret should be metropcs <--lowercase, DMU public should be 0, MN Authenticator should be 0.
Click view info and pick MIP customer profile 1 and make sure Enable profile is DISABLED. Now do the same with the other 4 profiles (profiles 2-5), make sure that the only profile enabled is MIP Default Profile.
Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778 call button (PST/EPST), we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to [email protected], password should be metropcs<--lower case, same for PPP user id and Password make them same as HDR.
Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both metropcs<---lowercase, then click menu OK and let it reset.
belalucf said:
Yeah I tried inputting all the settings, then creating a new connection called metro pcs with all the port settings and stuff, which I don't even see on this guide. Because if you don't create a new connection, it wont do anything once I removed the sprint connection which I did by changing the guardian file, which allowed me to even remove it. But I was hoping that this program would I guess populate that stuff somehow, so I went through and manually put in all those settings. Still no connection
Click to expand...
Click to collapse
Wap
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
hard way
ok you can try this out i have not try it so i dont know if it would work first go to control panel, then system hardware, device manager click universal serial bus controllers and unistall all of them restart your pc and it would install back the usb drivers then connect the phone diag mode if doesnt ask for drivers go to control panel, then system hardware, device manager go to ports( com & lpt) you should see htc diagnostic port if the port is below 27 we are fine if not delete all of them but do not unistall com 1. dont worry it will delete ports that u install thins when u plug things u have to install again so don worry. now if the phone ask you for drivers once u delete everything install them again but this time if still port higher than 27 go to device manager click in com 1 click update drivere install from specific locatiuon, dont search i will install have disk browse go to programs files /WModem_Installer/qcusbmdm.inf next yes ok and thats it you have it in com 1 after u done everything just delete port com 1 and it will install it after u reset the computer thank u..
u need to install WModem_Driver_Installer_v1.2.2
from metropcs.rar
try it in your friends computer or some internet cafe pcs hehehe i know bro always something happens
belalucf said:
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
Click to expand...
Click to collapse
if that doesnt work
i pretty sure it will work but just in case the methods dont work try to borrow a pc from ur friend or go to an internet cafe hehehehe
belalucf said:
You're gonna hate me but cdma workshop only goes up to like com25, and the htc device automatically sets itself to com63 regardless of what usb port i put it in. I tried to change it but it shows all the previous ports being used.
Click to expand...
Click to collapse
thanx for all the help i had wap and mms working but internet sharing and gps didnt thanx again
GPS
cdw9800 said:
thanx for all the help i had wap and mms working but internet sharing and gps didnt thanx again
Click to expand...
Click to collapse
Do you have quickGPS installed??? This it is available on the forums and wiki just do a search. It downloads updated satellites for google and other apps to use.
metro pcs
Well i got cdma to see the htc, but when i open the browser it says provisioning data services and says it can't connect.
check
ok just please more specific which rom are you using and the steps u did
belalucf said:
Well i got cdma to see the htc, but when i open the browser it says provisioning data services and says it can't connect.
Click to expand...
Click to collapse
Awesome
I wanted to change carriers from Cricket to MetroPCS. Metro told me I would have to go to Dallas to have the Metro flash applied. Well that is a 2+ hour drive from where i am. I like Metros pricing plan. I can have 3 phones for the same amount I pay for 2 Cricket. Good job on this write up and work you have done.
.................................
I'm pretty sure this is not possible.
Not possible at all.
Sent from my DROID X2 using XDA Premium App
ferg40 said:
Not possible at all.
Sent from my DROID X2 using XDA Premium App
Click to expand...
Click to collapse
Some dude did something like this but with cricket its from rootzwiki i don't know if it help but i hope it does i never had the patience to read it good luck!
Code:
Full Flash Motorola Droid X2 to Cricket: Talk, Text, MMS, Internet
TECH DIGITAL'Z DROID X-2 Flash to cricket tutorial
INTERNET,APPS,TALK,MMS,AND TEXT, ON $45.00 PLAN!
------------------------------------------------------------------------------------------------------------------
First you will need to collect a few programs and files.
1.Motohelper Drivers 5.0, these can be gotten from the motorola website
2.Droid Explorer 64 bit or X86 depending on your computer and OS (just google the name)
3.Gingerbreak
4.GreenK45 Free or Pro (Shout out to Mraabhimself for this one) its only 1.99 for pro in the market and you wont get nagged to buy!
5.CDMA Workshop
6.QPST 2.7 Build 366 (note: the older builds WILL NOT connect to the X2)
7.A cricket wireless PRL (those can be found in the PRL section of Mycricketforum.com)
8.HW Virtual Serial Port (Google it)
U CAN GET ALL OF THESE FILES BY DOWNLOADING MY PACK!
TECH DIGITAL'Z Droid X and Droid X2 Cricket Flash Pack.zip
9. NV items from http://www.whiterabbit.org/android (u must generate this uniquely with your [email protected]cricket.com your MDN is the number everyone uses to call you!
-------------------------------------------------------------------------------------------------------------------
First off if the phone hasnt been activated yet or you have to clear all settings and you get stuck at the activation screen... REMOVE THE BATTERY AND USB PUT THE BATTERY BACK IN AND TOUCH THE DROID AS SOON AS YOU SEE IT! this will get you past the activation screen.
-------------------------------------------------------------------------------------------------------------------
Put your phone in PC mode,and shutdown
DO NOT PRESS POWER, Plug in USB to turn it back on.
Install HW Virtual Serial Port on your Computer.
The password is admin, go to Settings and uncheck NVT Enabled as it will cause issues if you dont
-setup your Virtual Serial Port for Com 10
Ip address is 192.168.16.2
set Port as 11008
Click CREATE COM
-------------------------------------------------------------------------------------------------------------------
At this point youre ready to open CDMA Workshop ( note: if you have a cracked version you may need to disable your antivirus to get it to work)
Once open Connect to Com 10
it should say successfully connected at the bottom if not go redo the steps above.
If all is Right with the world (J/p) lol .... Please continue to next step
On security tab send SPC 000000 (you should get a message saying the spc is correct and phone is now unlocked)
Go to tab labeled "Other" and write prl (this is where the PRL you downloaded comes into play) Select it from the location in which you downloaded it.
Goto "Memory" tab and click write under NV items, find the downloaded NV items you got from
http://www.whiterabbit.org/android
for example you must generate the NV items by inputing your MDN
(Your [email protected]). box opens telling you to save them as .txt and select them with cdma workshop2.7.
It should now say, 12 NV items were successfully written to phone.
Go to Main tab and click mode reset, The phone will restart,( at this point youre ready to talk and text on cricket)
---------------------------------------------------------------------------------------------
LETS GET ROOTED!!!!
Have Droid Explorer Installed on your computer
Have your phone connected USB and in PCmode
Open Droid Explorer and Connect to your phone
Click the little Icon that looks like a box with a cd in front of it,
It should open a Install Window
Click install and install Gingerbreak (I used Gingerbreak Version 1.20)
Now on your phone go into your apps menu and run gingerbreak
CLICK ROOT! the phone should then run gingerbreak and restart.
You should now be rooted!
NOW TO GET INTERNET AND APPS WORKING!!!
if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say (your [email protected] )etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone.
Phone will now restart.
After the phone has started up Go to wireless setting in settings and connect to wifi, Open the Market and install GreenK45free or Buy Pro.
Disable your Wifi now so that 3g can come back on. once you see 3g at the top open greenK45 and click Enable. (MAKE SURE YOU ALLOW GREENK45 ROOT ACCESS)
also when it restarts allow U2nl Proxy access to root) Just incase you dont know the Superuser will pop up asking you to allow or deny, click Allow!
You should now have Internet and Apps should have Connection.
As for MMS i havent found a way to get this working correctly yet on the Droid X2 but i will write a update to this tutorial when i do, AS OF NOW, INTERNET,APPS,TALK,AND TEXT WORK. MMS or PICTURE MESSAGING ARE BROKEN!
THANKS TO MRAABHIMSELFfor GreenK45
and anyone i may have missed for their contributions to this tutorial ....
MMS IS NOW FIXED, HERES WHAT YOU DO!
.Go to Market and download Apn Backup and Restore
.Open and Delete all APNS
.RESTART PHONE, I CANT STRESS HOW IMPORTANT THIS IS!
.Go to market and Download and install Anycut, Open it and choose Activity,Scroll down and select APNs create the shortcut then exit
.click the apns shortcut you just made, it should be on your main screen
.hit menu button and select New APN
.Enter these settings into your apn
Name - Cricket
APN internet
Proxy wap.mycricket.com:8080
Port 8080
Username [email protected]
Password cricket
Server wap.mycricket.com
MMSC http://mms.mycricket.com/servlets/mms
MMS Proxy wap.mycricket.com
MMS Port 8080
MCC 310
MNC 004
Authentication Type PAP or CHAP
APN type <Not set>
.Hit the Menu button again and hit save!
.Restart and youre done, YOURE FULLY FLASHED WITH EVERYTHING!
Hey man, thanks for putting together this set of instructions. Where can I download your flash pack? (TECH DIGITAL'Z Droid X and Droid X2 Cricket Flash Pack.zip). Thanks again for your work!
nope
FLashing to Cricket is NOT the same as changing the MEID on a Phone.
Besides Modifying Mobile Electronic Identification Numbers is Ilegal in the US.
FYI. IT IS POSSIBLE but very hard, specially on Motorola devices.
try this method. allthough its buggy it might work.
http://www.howardforums.com/showthr...droids)-ESN-and-MEID-correction-repair-SOLVED
not responsible for any damages tho.
Good Luck
LJ
The last couple of days I have really enjoyed trying out these new roms the Mx2 but I can never get the mms to work. My mx2 is with Bluegrass Cellular and if anyone can share the correct setting I would appreicate it. I have searched and searched and cant seem the find the correct ones.
fergie_cn said:
The last couple of days I have really enjoyed trying out these new roms the Mx2 but I can never get the mms to work. My mx2 is with Bluegrass Cellular and if anyone can share the correct setting I would appreicate it. I have searched and searched and cant seem the find the correct ones.
Click to expand...
Click to collapse
Try this tutorial. It's not for MX2 but its still for ICS and its what I did to get my MMS working on Cspire.
http://forum.xda-developers.com/showthread.php?t=1671592
I have tried that and could not get it to work.
Sent from my Milestone X2 using xda app-developers app
754boy said:
Try this tutorial. It's not for MX2 but its still for ICS and its what I did to get my MMS working on Cspire.
http://forum.xda-developers.com/showthread.php?t=1671592
Click to expand...
Click to collapse
Those settings were incorrect for my phone.
Sent from my Milestone X2 using xda app-developers app
fergie_cn said:
Those settings were incorrect for my phone.
Sent from my Milestone X2 using xda app-developers app
Click to expand...
Click to collapse
I too have bluegrass and could not get MMS to work forever. Finally I found the right combination of fixes that works for me (and has been replicated on all my coworkers devices). I am using this on Eclipse 2.3 on my MX2. I do not know if it will work for other carriers or other ROMs. Use at your own risk.
First, you will need root (which you have if you are on a custom rom), and you will need a file explorer that let's you browse with root permissions (I use ES File Explorer with root options set in settings).
Browse to /system/etc/ and replace apns-conf.xml with all the .xml files from the Conf folder in the attached Conf.zip file. I am not sure why there are so many, I copied them from a stock Bluegrass MX2. (Feel free to make a backup of your original apns-conf.xml prior to replacement).
Now, browse to /data/data/com.android.providers.telephony/databases/ and delete the 3 .db files here. (Again, make a backup if you wish). This will remove your existing text messages off your device!
Restart your device.
Now download "APN Settings Shortcut" from the Play Store. This is not an app or widget, but an actual shortcut. Press and hold on an empty space on your home screen and choose Shortcut and then APN Settings Shortcut.
Once it opens, hit menu and then new. Populate all fields with the following settings:
Name
Bluegrass Cellular (this doesn't matter, can be named anything)
APN
internet
Proxy
66.255.55.23
Port
9201
Username
%[email protected]
Password
blue
Server
*
MMSC
http://mms.iot1.com/bluegrass/mms.php
MMS proxy
66.255.55.23
MMS port
9201
MCC
DO NOT CHANGE THIS, LEAVE THE NUMBER THAT IS THERE
MNC
DO NOT CHANGE THIS, LEAVE THE NUMBER THAT IS THERE
Authentication type
PAP or CHAP
APN
mms
APN protocol
IPv4
Now click menu and save.
Your MMS now works!
This guide is a combination of fixes found at the links below:
http://forum.xda-developers.com/showthread.php?t=1671592
http://forum.xda-developers.com/showthread.php?t=1822890
http://forum.xda-developers.com/showthread.php?t=1815822
All credit goes to them, I just kept trying fixes until one worked for me, and it ended up taking a combination of three.
hilltopper06 said:
I too have bluegrass and could not get MMS to work forever. Finally I found the right combination of fixes that works for me (and has been replicated on all my coworkers devices). I am using this on Eclipse 2.3 on my MX2. I do not know if it will work for other carriers or other ROMs. Use at your own risk.
First, you will need root (which you have if you are on a custom rom), and you will need a file explorer that let's you browse with root permissions (I use ES File Explorer with root options set in settings).
Browse to /system/etc/ and replace apns-conf.xml with all the .xml files from the Conf folder in the attached Conf.zip file. I am not sure why there are so many, I copied them from a stock Bluegrass MX2. (Feel free to make a backup of your original apns-conf.xml prior to replacement).
Now, browse to /data/data/com.android.providers.telephony/databases/ and delete the 3 .db files here. (Again, make a backup if you wish). This will remove your existing text messages off your device!
Restart your device.
Now download "APN Settings Shortcut" from the Play Store. This is not an app or widget, but an actual shortcut. Press and hold on an empty space on your home screen and choose Shortcut and then APN Settings Shortcut.
Once it opens, hit menu and then new. Populate all fields with the following settings:
Name
Bluegrass Cellular (this doesn't matter, can be named anything)
APN
internet
Proxy
66.255.55.23
Port
9201
Username
%[email protected]
Password
blue
Server
*
MMSC
http://mms.iot1.com/bluegrass/mms.php
MMS proxy
66.255.55.23
MMS port
9201
MCC
DO NOT CHANGE THIS, LEAVE THE NUMBER THAT IS THERE
MNC
DO NOT CHANGE THIS, LEAVE THE NUMBER THAT IS THERE
Authentication type
PAP or CHAP
APN
mms
APN protocol
IPv4
Now click menu and save.
Your MMS now works!
This guide is a combination of fixes found at the links below:
http://forum.xda-developers.com/showthread.php?t=1671592
http://forum.xda-developers.com/showthread.php?t=1822890
http://forum.xda-developers.com/showthread.php?t=1815822
All credit goes to them, I just kept trying fixes until one worked for me, and it ended up taking a combination of three.
Click to expand...
Click to collapse
Self Bumping an old post so that anyone still in need can get some additional for ICS roms.
You can edit the APN information on ICS roms (or at least the latest CM9 Beta) by opeing Voice Dialer (it is a preinstalled app) and saying:
A P Ns
Then choose Open APNs. Hit the menu button and choose new, then enter the same information listed above. Hit the menu button again and choose save. Reboot and enjoy MMS on ICS.