Hey Guys,
I tried flashing my rom to CM7 and in the process the phone rebooted and got the error message
SVF:105:1:2
failed to boot 0x1000
No OS detected, going to RSD mode
in 5 seconds
Press a key to stop countdown
Available modes are:
1. RSD
2. Fastboot
3. NVFlash
4. BP HW Bypass RSD
5. BP HW Bypass QC Dload
6. BP Diag & boot AP
7. BP HW bypass BP only
8. BP SW bypass RSD
9. Andriod Recovery
10 .Boot andriod (No BP)
11. Device UID
12. console=ttyS0,115200n8
13. Early USB Enumeration
14..BP tools
I get the error message in the rsd lite as error switching to BP and something.
Kindly help i am really confused.
Soft brick .
Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files
Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM
Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip
open cmd and navigate to C:\moto-fastboot\
Force fastboot on phone by holding down PWR and VOL UP while inserting battery.
Type these commands:
moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)
when finished, then enter these commands:
moto-fastboot flash boot boot.img
moto-fastboot flash system system.img
moto-fastboot -w
moto-fastboot reboot
When it reboots, you will be back to stock, fully restored!!
I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.
I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:
moto-fastboot flash recovery recovery.img
Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go
No need to do all that.
Since you want to get CM7, Unlock the phone.
Ignore the instructions to flash system.img, that will bring you back to stock.
Enter fastboot, flash a recovery. (Above post last instruction)
Enter recovery mode, than flash CM7 from there.
(I assume you are familiar with what I am talking about, and don't require step by step instructions)
Bricked
Thank u for ur replies i havent tried it yet but i wish it wud work i was using the latest update from AT&T i think since i tried to boot for the older version this happened i am not sure though.
There has been posts about trying to unlock after applying AT&T latest update. You should read up on those, I remember it could brick your phone, be careful!
Thank You
Dear All,
Thank u a hundred thousand times for helping me get rid of the problem i owe u guys a lot finally got to work.
Thank u once again i dont have words to describe my joy.At ant time u want help in India count me in.
this happened to me to, all i did was go to fastboot and unlock the bootloader and it let me boot again after recovering to a rom i had on my SD. i did try and install a custom recovery when it bricked.
HI ranjit
Hi ranjith
need your help
can u drop in ur cell number
or call on 9860521352
thanks in advance
kumar brijwani
ranjithkumar1201 said:
dear all,
thank u a hundred thousand times for helping me get rid of the problem i owe u guys a lot finally got to work.
Thank u once again i dont have words to describe my joy.at ant time u want help in india count me in.
Click to expand...
Click to collapse
kumarbrijwani said:
Hi ranjith
need your help
can u drop in ur cell number
or call on 9860521352
thanks in advance
kumar brijwani
Click to expand...
Click to collapse
9036523279
feel free to sms me
i try to help you in anything i know
it would be better if you could message in Whatsapp
Sent from my MB860 using xda premium
DL here http://forum.xda-developers.com/show....php?t=1475444
error page not found
you can solve this problem....
tank's
hoaca388 said:
Soft brick .
Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files
Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM
Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip
open cmd and navigate to C:\moto-fastboot\
Force fastboot on phone by holding down PWR and VOL UP while inserting battery.
Type these commands:
moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)
when finished, then enter these commands:
moto-fastboot flash boot boot.img
moto-fastboot flash system system.img
moto-fastboot -w
moto-fastboot reboot
When it reboots, you will be back to stock, fully restored!!
I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.
I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:
moto-fastboot flash recovery recovery.img
Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go
Click to expand...
Click to collapse
Related
I am trying to unlock my bootloader. I went through all the steps and couldn't get it to work. I am currently rooted and that is it. I put my phone into rsd mode, put the sbf into rsdlite and then plug my phone in. I click start and everything seems to work until it gets to 98%. The status says BP Pass Through and then it says failed. I am running rsdlite 5.6.
dwh1996 said:
I am trying to unlock my bootloader. I went through all the steps and couldn't get it to work. I am currently rooted and that is it. I put my phone into rsd mode, put the sbf into rsdlite and then plug my phone in. I click start and everything seems to work until it gets to 98%. The status says BP Pass Through and then it says failed. I am running rsdlite 5.6.
Click to expand...
Click to collapse
It's supposed to fail. After it does, boot into fastboot then issue the unlock commands in fastboot from your computer:
Code:
moto-fastboot oem unlock
copy the unique id that it spits out then
Code:
moto-fastboot oem unlock yourid
this assumes that you are inside the moto-fastboot directory or have added moto-fastboot or fastboot to your path.
I have an Atrix 4G ATT. During RSD it failed and sent me to a screen with
"SVF:105:1:2
Failed to boot 0x1000
no os detected, going to rsd mode in 5 seconds
press a key to stop count down
available modes are:
1:rsd
2:flashboot
..."
What caused this was while following http://forum.xda-developers.com/showthread.php?t=1302423, the rsd said failed, i waited till 100% like guide said, and then got this screen.
What can i do to fix this, from each forum i read, i don't understand, or follow old links. I am a noob.
edit: When i Choose fast boot nothing happens, when i check other forums, they have megaupload links (shut down). am i missing something?
I don't know it'll fix the thing or not But you should try this method. It may work.
Skip any steps you have already done.
A. Download a fruitcake from here. http://forum.xda-developers.com/showthread.php?t=1163009
B. Download a radio from that same thread, below the fruitcakes. Or if you prefer, download a different radio.
C. Put them both on your external (or internal if you really want to) SD card.
D. If you haven't, download RomRacer's recovery. Here. http://forum.xda-developers.com/showthread.php?t=1204500
E. Reboot into fastboot mode by holding volume down + power button until Fastboot appears on screen, then hit the Up arrow. This takes you into fastboot mode, I'm assuming you already have fastboot installed. If not, google how to set up fastboot or download moto-fastboot.
F. Make sure the recovery you downloaded above is in the same folder you downloaded fastboot or moto-fastboot to.
G. Connect phone to computer, open command prompt, navigate to fastboot or moto-fastboot folder (cd c:/(where you installed fastboot / moto-fastboot)
H. Type these in, after entering each one hit enter: Fastboot erase system fastboot erase userdata fastboot erase cache
fastboot erase webtop fastboot erase preinstall fastboot erase boot fastboot erase recovery
I. Type Fastboot flash recovery (name of your romracer recovery image)
J. Type fastboot reboot and when it reboots, hold down volume + power then keep hitting down when fastboot appears till you see android recovery, then hit the volume up key.
K. Enter recovery,erase Dalvik Cache under Advanced setting, then flash the new ROM you downloaded. * the fruitcake*. Let it completely do its thing.
L. Now if you've gotten this far, you're on a good path and most likely you wont have to flash the radio you downloaded. If not, you may have to. If none of this matters and after completely erasing all that stuff in fastboot mode you STILL get the same error on boot up I would have to assume it's an actual hardware problem and you will have to get a new phone.
Hello,
I've rooted my atrix today using rootzwiki without any problems and there was a boot loader unlock tutorial, my device is 2.3.4 4.5.91 at&t but unfortunately I used .sbf for international users and not for at&t..ending up with "no os" no boot/recovery so tried to flash "1FF-olympus-user-2.3.4-4.5.91-110625-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P011.sbf" (mistake?) with no success, then flash "4547-fix-try2.sbf" for at&t but no success.
Don't know what to do Plz help me
Download fastboot here:
http://dl.dropbox.com/u/30173981/fastboot.zip
Download a ROM such as
CM7 Based ROM (Neutrino ROM)
http://forum.xda-developers.com/showthread.php?t=1398819
CM9 Alpha/Beta
http://forum.xda-developers.com/showthread.php?t=1445052
http://forum.xda-developers.com/showthread.php?t=1500535
OR Blur Based Rom (NottachTrix4G)
http://forum.xda-developers.com/showthread.php?t=1567241
Have the ZIP file ready
Extract contents of the fastboot zip in the c drive root in a folder called "fastboot" without the quotes
Install the Motorola Drivers, included in the fastboot folder I provided
Next, download a recovery, such as romracer's recovery
http://forum.xda-developers.com/showthread.php?t=1204500
(Rename img file to recovery.img)
And put the recovery.img file in the fastboot folder
Open a command window (Start > Run > CMD OR Start > type 'Command Prompt'), type "cd\fastboot" without the quotes > Press enter
Next power on phone, in fastboot mode (hold power button and volume down and press volume down to look for fastboot, volume up to select it), plug it in
Go to your command window and type
"fastboot flash recovery recovery.img” without the quotes
Once that is done, do
"fastboot reboot" without the quotes
Once the phone is at the Motorola logo, power it off.
Power it back on and go into Android Recovery (hold power button and volume down and press volume down to look for Android Recovery, volume up to select it), plug it in
(recovery navigation is volume up/down is up and down, select is power button)
From here, go to mount and storage and mount USB and dump the rom zip in the root and go back on the phone and factory reset, wipe cache and install zip from SD card. Find the zip file and install it. Once that’s done reboot and your phone should boot up in the ROM of your choice.
TNX! but it fails to flash recovery
Leonoduzit said:
TNX! but it fails to flash recovery
Click to expand...
Click to collapse
You did not unlock your boot loader, download this if you have an at&t atrix
http://diamantephoto.com/pudding.rar
or if its an international atrix
http://diamantephoto.com/IHOP_Bell.rar
download the sbf and flash using rsdlite and retry my steps again
OK OK
Once you enter that line, if you don't get an error make sure the command prompt says "C:\path\to\fastboot\ > __" confirming that you are working in the right directory. Now type 'fastboot oem unlock' (fastboot tells command prompt to work with fastboot.exe and oem unlock is a command within the program). It will reply a warning about breaking warranty, etc., and also a lengthy ID for your phone.
Now type 'fastboot oem unlock ####' where #### is your ID. And finally 'fastboot reboot'. Your phone will obviously restart and you can close out of the command prompt.
When turning on your phone will say! "Unlocked" on the Motorola boot screen, jump up and down in joy!!!
Sorry, I did not give the link to the pudding thread; those are the instructions
Sent from my MB860 using XDA
I have 4.5.141 unlocked, rooted and I have GooManager installed, I try to have it flash the TWRP version 2.1.1 recovery for me automatically so I can try to download and flash a custom ROM and it downloads and it flashes the custom recovery and the phone reboots and I get an error that reads "Failed to Boot 2 Starting RSD Mode" and when I pull the battery, the phone reboots and the "Failed to boot 2" message does not show up. Can anyone help me in trying to successfully flash a custom recovery onto my Atrix 4G?
ksweeley said:
I have 4.5.141 unlocked, rooted and I have GooManager installed, I try to have it flash the TWRP version 2.1.1 recovery for me automatically so I can try to download and flash a custom ROM and it downloads and it flashes the custom recovery and the phone reboots and I get an error that reads "Failed to Boot 2 Starting RSD Mode" and when I pull the battery, the phone reboots and the "Failed to boot 2" message does not show up. Can anyone help me in trying to successfully flash a custom recovery onto my Atrix 4G?
Click to expand...
Click to collapse
Download TWRP recovery from this thread
Download moto-fastboot-win32.zip from this thread
Unzip them both to the same folder on your computer (eg.: c:\fastboot).
Make sure all files are in the same folder: moto-fastboot, the ADB DLL files and recovery.img
Open a command prompt window pointing to that folder (tip: hold shift on the keyboard, right click on the folder and select "open command window here")
Connect yout atrix to your pc via USB and boot your atrix into fastboot mode (when the phone is off, keep the VOL - button pressed and press the power button. When Fastboot appears, press VOL +)
Now issue type these commands into the command prompt:
moto-fastboot erase recovery
moto-fastboot flash recovery recovery.img
after it's done, type
moto-fastboot reboot
After that you should be able to boot into TWRP recovery. Cheers!
vladeco said:
Download TWRP recovery from this thread
Download moto-fastboot-win32.zip from this thread
Unzip them both to the same folder on your computer (eg.: c:\fastboot).
Make sure all files are in the same folder: moto-fastboot, the ADB DLL files and recovery.img
Open a command prompt window pointing to that folder (tip: hold shift on the keyboard, right click on the folder and select "open command window here")
Connect yout atrix to your pc via USB and boot your atrix into fastboot mode (when the phone is off, keep the VOL - button pressed and press the power button. When Fastboot appears, press VOL +)
Now issue type these commands into the command prompt:
moto-fastboot erase recovery
moto-fastboot flash recovery recovery.img
after it's done, type
moto-fastboot reboot
After that you should be able to boot into TWRP recovery. Cheers!
Click to expand...
Click to collapse
I'm having a problem, I typed in moto-fastboot erase recovery and it says
"erasing 'recovery' ... FAILED <remote: <00180001>>"
and on the phone itself it reads in red text:
"Failed to process command erase:recovery error(0x180001)"
Is there a way to fix this error?
I fixed this, re-flashed the pudding.zip file I found, and I got the recovery to flash.
ksweeley said:
I'm having a problem, I typed in moto-fastboot erase recovery and it says
"erasing 'recovery' ... FAILED <remote: <00180001>>"
and on the phone itself it reads in red text:
"Failed to process command erase:recovery error(0x180001)"
Is there a way to fix this error?
I fixed this, re-flashed the pudding.zip file I found, and I got the recovery to flash.
Click to expand...
Click to collapse
Hi, Could you please share the steps for the resolution? I have read about pudding, also i tried but can not achive. Thanks
So I tried to change the ROM of my phone because the vendor's one had malware but it was worse, my phone is stuck at boot screen and can't do anything with it.
First I tried to install a ROM with TWRP, it installed but it was just a black screen, you could only see the battery status.
Then I tried to install the global ROM that is on the official xiaomi site but it didn't work and it locked my phone.
Now I can't use TWRP, please help me. I am desperate.
Miflash isn't detecting the phone, but the PC does cause it listed under Android Phone->Android ADB Interface on device manager.
1st:
http://en.miui.com/thread-277276-1-1.html
Once you rebooted it into download mode, use this:
http://en.miui.com/thread-254606-1-1.html
My PC is no longer detecting the phone, only detects Qualcomm 9008
Ok, it is working till the miflash step it says "receiving hello packet" in red
You will need to flash a ROM using fastboot.
First install fastboot on your pc: http://www.theandroidsoul.com/how-to...t-setup-75174/
Second Download a flashable Rom: http://en.miui.com/a-234.html (make sure to choose the right one)
Unzip the rom and navigate to the 'images' folder
Put the phone into Fastboot mode (volume down and power button together until fastboot appears)
Connect the phone to pc with USB
Shift Right click on a blank space in the folder and choose 'open command window here'
run the following commands. one at a time
fastboot devices
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash cache cache.img
fastboot flash userdata userdata.img
fastboot flash system system.img
fastboot reboot
Feriol said:
You will need to flash a ROM using fastboot.
First install fastboot on your pc: http://www.theandroidsoul.com/how-to...t-setup-75174/
Second Download a flashable Rom: http://en.miui.com/a-234.html (make sure to choose the right one)
Unzip the rom and navigate to the 'images' folder
Put the phone into Fastboot mode (volume down and power button together until fastboot appears)
Connect the phone to pc with USB
Shift Right click on a blank space in the folder and choose 'open command window here'
run the following commands. one at a time
fastboot devices
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash cache cache.img
fastboot flash userdata userdata.img
fastboot flash system system.img
fastboot reboot
Click to expand...
Click to collapse
After that I use miflash?
Failed after second command
Hello guys, i have a redmi 3s china version, so i try to find global version, i installed all driver and try to use with miflash that:
land_global_images_V7.5.9.0.MALMIDE_20160805.0000.29_6.0_global_470b843c10.tgz
(if i use xiaomiflash i get error) meanwhile with miflash i see device and i flash it but something wrong , i restart the phone i stuck on the logo MI
I try also to download land_global_images_V7.5.4.0.MALMIDE_20160523.0000.23_6.0_global_dc5d804271.tar
seems is the right firmware
So i try again to flash in fastboot mode with miflash but i get error like i have no permission.
So i extract the whole firmware on a dir where there is ADB files , same problem...the device is locked
I try online the procedure with sms to unlock the bootloader ( i think is the only way, right?) or there are any other solution?
Maybe there is a stock rom to replace the original rom and put the global rom in another way?
Thanks in advanced
Bye
Benz83 said:
Hello guys, i have a redmi 3s china version, so i try to find global version, i installed all driver and try to use with miflash that:
land_global_images_V7.5.9.0.MALMIDE_20160805.0000.29_6.0_global_470b843c10.tgz
(if i use xiaomiflash i get error) meanwhile with miflash i see device and i flash it but something wrong , i restart the phone i stuck on the logo MI
I try also to download land_global_images_V7.5.4.0.MALMIDE_20160523.0000.23_6.0_global_dc5d804271.tar
seems is the right firmware
So i try again to flash in fastboot mode with miflash but i get error like i have no permission.
So i extract the whole firmware on a dir where there is ADB files , same problem...the d: evice is locked
I try online the procedure with sms to unlock the bootloader ( i think is the only way, right?) or there are any other solution?
Maybe there is a stock rom to replace the original rom and put the global rom in another way?
Thanks in advanced
Bye
Click to expand...
Click to collapse
Try this: https://www.reddit.com/r/Xiaomi/wiki/roms/flashofficial
or this: http://en.miui.com/thread-290959-1-1.html
andrespm said:
After that I use miflash?
Failed after second command
Click to expand...
Click to collapse
After you run 'fastboot devices' is anything listed? Usually a string of numbers. If not then the computer isn't seeing your device.
Try rebooting the computer, and trying different USB leads and ports if possible and try again.
Using this method you don't have to use MiFlash, and is for when MiFlash doesn't work.
Once your phone is working again you can try again to install another ROM using traditional methods.
andrespm said:
Try this: https://www.reddit.com/r/Xiaomi/wiki/roms/flashofficial
or this: http://en.miui.com/thread-290959-1-1.html
Click to expand...
Click to collapse
Hello, i try the steps you give for EDL, after it the screen is not black but i see again the logo MI, i can go on fastboot mode but if i try to flash anykind of rom i get error "FAILED: remote: Critical partition flashing is not allowed)
other solution?
I think the only way is the unlock bootloader, but sincerally i dont know how it work. i did the steps online and the sim is on another device not xiaomi. I will get a sms from xiaomi with some kind of code? and after it how can use for bootloader?
There is another solution? I thinking....but why i cant use the original rom ?? always about the bootloader lock?
___
now i see another post ...use both volume to enter in download mode and on the miflash i saw port com 49, load a rom and start to flash it ...but....another error : The system can not find the file specified (0x80070002: Max buffer sector is 256)
___
This Morning i received the unlock code. When i use the tool stuck on 50℅