As the subject says guys, I rooted my gf's x10i and installed cwm via Flash tool 2.9.1. Was about to unlock the bootloader to install a custom rom when (I swear this was the dumbest moment in my entire life) I clicked the "Optimize button" (FOR NO REASON) I'm on 2.3.3, it said "phone rebooting", my phone did nothing so I disregarded it. however, when I restarted it, the phone went to the sony erricson screen and just shutdown and restarted again and again and again. I booted into cwm recovery but to my horror it kept saying sd card in use when i try to intall a zip from sd (which I learned from this site means it's the wrong ver. cwm for my phone) So the gist is phone restarts every 10-15 seconds, I can't use cwm properly because of the version. and flashtool because it keeps resetting so quickly.
PLEASE PLEASE HELP!!!!
just simply reflash ? or use SEUS to flash stock software ?
i just read it again an saw the part where flashing wont work but i seem to be able to reflash before getting the SE logo ?
Bjornlindekens said:
just simply reflash ? or use SEUS to flash stock software ?
i just read it again an saw the part where flashing wont work but i seem to be able to reflash before getting the SE logo ?
Click to expand...
Click to collapse
Ok so walk me through this because I'm pretty new to it. When you say you reflash before you get to the SE logo. Does the phone have to be in fastboot? (hold back button?) because flashtool detects it and then it disconnects due to the restart. THANKS FOR THE REPLY!!
the way i do it is
1 select what im flashing (then it will tell you to turn off phone etc.etc.)
2 remove battery
3 unplug phone
4 reconnect phone
5 hold back button and keep holding it
6 slide battery in while still holding back button
about 5-10 sec later it should get detected :s
i really hope this helps because i dont think theres anything you can do if you cant even manage to flash the phone :s
ill look for simular problems and/or info :s
---------- Post added at 04:32 PM ---------- Previous post was at 04:29 PM ----------
this might be a stupid question but try recharging the phone a while if your not doing that already .
The charge light doesn't come on and yea with the 15 second restart, as soon as it is detected, like a few seconds later it restars and says disconnected. I looked all over and there is noone I find with a similar boot loop. I tried wiping my data via cwm recovery but same problem.
Ok so this might be a dumb ass thing to ask but I will ne way. If I can get a backup of someone else's x10 would I be able to apply it via cwm? Or will that fail like the zip install?
i've bin looking around aswell and couldnt find any simular problem
so the only thing i can suggest is not keeping this in the X10 Q&A but try the general aswell this might attract more people scouting trough.
but tbh im unable to see any options because as im reading i collected this info.
1) cant fastboot/flash anything (no option there)
2) cant use CWM recovery cause its the wrong version and reads the internal flash memory (called sdcard) but not your external microsd card (called external1???)
(correct me if im wrong on the second one)
if this is the case what else is there ?
Hi, sorry about your problem. I don't know a lot about this phone but ill give you the steps that got me going when I had a different issue.
This was in an email directly from Sony, hopefully it'll help, if not then at least I tried.
To Repair your phone Software, please follow the steps below:
Click on this link to download PC Companion http://www.sonymobile.com/us/tools/pc-companion/ .
Turn the phone off and disconnect it from the computer. Run the Software.
1. No matter what the program says do not connect the phone until you complete step 9.
2. In the welcome screen if asked click on Start, next you will be shown what Media Go offers, click on "next" then you will see a presentation on what Support Zone offers, click on "Finish".
3. In the next section from "Support Zone” and "Media Go" new select “Support Zone" and click on start.
4. On the next page select "Software Update" and click on "Start".
***At this point if you get an error stating that "unable to install update components" or "server is busy”, please proceed to step 12.
5. The program will say that there is no phone connected and will ask you to connect but disregard that and instead choose the option to "Repair Phone". (The program will issue you a warning on the content that you will lose during the update).
that any data saved only in your phone memory will be erased as part of the Phone Repair.
6. Choose Continue.
7. After that, the program will download the necessary information (several minutes) and it will present you with a list of phones.
8. Choose the X10 from the list (close to the bottom of the list) by clicking on the icon for the phone. Then click on "Next". Then you will see a new section telling you how to connect the phone. (Don't connect it yet!).
At this point the phone must be off and disconnected from the PC.
9. Connect the cable to the PC but not to the phone, then while pressing and holding the back key (the one on the lower right part of the screen that has the icon of an arrow pointing to the left on top) Connect the cable to the phone and keep holding the back key until the program says "The update of your phone has started..." (In some cases a message of "Installing drivers" will appear before the message of "The update of your phone has started..." is shown.).
10. If the steps were not followed exactly the phone will turn on and it will request that you "Proceed with the following steps, slide down the notification bar".
happens disconnect the phone from the cable, turn it off and repeat from step 9).
11. If PC Companion proceeds correctly with the update it will tell you to release the back key.
the update to finish and follow instructions on the screen.
12. If you receive the message: “Unable to install update components".
a. Close PC Companion.
b. Install Java from: http://www.java.com.
c. Start Pc companion again and try to do the software unlock process once more
As part of Sony Mobile's commitment to excellent customer service, we offer a wide variety of mobile products to suit your lifestyle. If you require more information, or have any other questions, please visit www.sonymobile.com or call us at 1-866-766-9374.
Hey guys thanks a bunch, I reflashed using flashtool. Apparently once the flashing takes, flash mode stays on (go fig right? lol) I really do wanna say thank you to you guys who helped me esp Bjornlindekens (I hit thanks don't worry )
Hooray happy i could help and glad for ya to getting it running again! !
Sent from my X10 using xda premium
Related
hello friend, Raj here.
I have been using the X10i since past 6 months. I bought the phone my UAE & i am presently using it in India.
1) Is there any firmware upgrade available for my phone?
My phone info says-
Model - X10i
Firmware - 1.6
Baseband version - 1.0.14
Build number - R1FA014
2) My phone does not have the Android market application inbuilt in it! how & from where do i download that app?
3) How do i install applications downloaded to my computer from Android market, to my phone?
4) I am not able to access Calender since it requires me to log in to my Gmail account. everytime i try to do that, it says "error, try next time"! is there any way i can start the calender without registering?
Thanks.
raj_5004 said:
1) Is there any firmware upgrade available for my phone?
Click to expand...
Click to collapse
Hi.
Yes there is, considering a lot of us are running R2BA026, that should give you an idea of how far behind you are.
raj_5004 said:
2) My phone does not have the Android market application inbuilt in it! how & from where do i download that app?
Click to expand...
Click to collapse
Personally, I would debrand and update your handset with UK generic FW, which will give you the Market app, which will answer question 3, and as you need to register for the Market to use it, that also answers your 4th question.
1) Install SEUS (Sony Ericsson Update Service).
You can get it from here: http://www.sonyericsson.com/cws/download/1/110/61/1275980198/Update_Service_Setup-2.10.6.21.exe
2) Run SEUS, follow the prompts. You don't need to update the phone through it, but get the phone ready for updating. This process should install the drivers necessary for the rooting process.
Note: I suggest you keep your USB cable attached to that USB port. Remember which USB port of your computer it's attached to, as changing USB ports can lead to a bit of confusion for the next 2 steps!
3) To check if #2 was successful, click on Start, click Run, and type: regedit
In the Registry Editor that pops up, click on Computer, press CTRL+F, and search for this: USB\Vid_0fce&Pid_adde\
After it's finished finding, on the right side you'll see DeviceInstance, then it says REG_SZ, then it says something like USB\Vid_0fce&Pid_adde\5&270d2a78&0&3
You'll need that last bit (in this example: 5&270d2a78&0&3 Yours would probably be different). This is your DeviceID (you'll need it soon!)
Note: You may have multiple of these if you plugged the USB cord into many USB ports on your computer. Each USB port will give a different DeviceID, so if you have more than one DeviceID, you'll have to choose one, and if it doesn't work (you'll find out when you reach #5!) you will have to choose another one.
Alternatively, download the file in the next step and extract it, go to the folder called 1st, and run the DeviceID.jar file. It should give your DeviceID
4) Download this:
http://filevo.com/1nlq8wryo11u.html
or from here: http://rapidshare.com/files/404363083/i_R1FA16_ft.rar.html
Extract it.
In the step1 folder, you'll see a file called DeviceID.txt
Open it up, delete whatever's there, and put YOUR DeviceID (that you found from the previous step).
Save the file and close notepad.
Note: Make sure there are no extra spaces or lines after/before the DeviceID. The ONLY thing that should be in the file is your DeviceID, NO SPACES/LINES (for example, only this: 5&270d2a78&0&3 [yours will probably be different])
5) Take out the USB cable from your phone (leave it plugged into your computer)
Turn your phone OFF
Open up step1.cmd (it's not inside the step1 folder, but outside it), but DON'T PRESS ANYTHING
Now we have to put the phone into flash mode. This is how you do it:
Hold the Back button on your phone, and while holding the back button, insert the USB cable into the phone.
A green light should come on the phone (like when it's charging or a missed call)
Quickly "Press any key to continue..." in the open step1.cmd window.
Let it finish what it's doing. It will say "Press any key to continue..." after it's finished. Until then, DON'T touch anything!
If you get problems in this step, refer to this post:
http://forum.xda-developers.com/showpost.php?p=6970868&postcount=3
Here's a helpful video for common java issue: http://forum.xda-developers.com/showthread.php?t=713457
After completion, this will give you a Generic X10i R1FA016 firmware (check it by pressing the left button, go to settings>about phone and at the very bottom under build number)
Click to expand...
Click to collapse
- Newbies Guide to Rooting X10 and giving you the newest firmware!
Follow those steps and when you've completed them run SEUS which should update you to R2BA026, and give you the Market app. If you run in to any issues read the links provided as the chances are it will be user error if you do.
Thanks a lot buddy.
Will de-branding my phone affect future upgrades to Android 2.1 in any way?
Also, why is de-branding necessary to access calender???
raj_5004 said:
Will de-branding my phone affect future upgrades to Android 2.1 in any way?
Click to expand...
Click to collapse
Nope, apart from you'll be the first in line to get it.
raj_5004 said:
Also, why is de-branding necessary to access calender???
Click to expand...
Click to collapse
It isn't, but if want to use the Market you are going to need a gmail account.
I tried using SEUS but failed at step 2 itself!
It says press back button while inserting USB cable in phone & keep pressing back button. i did the same & waited & waited for 5 minutes, but no response!
then my finger started hurting & i had to abort the process! does it take so long?
raj_5004 said:
I tried using SEUS but failed at step 2 itself!
Click to expand...
Click to collapse
You're not doing it right, should take about 5 seconds for seus to recognise the phone. Try again.
Sorry for the back-to-back posts, but can i update my phone country to India instead of UK? i think Indian X10s do get Android Market. Since i am using the phone here in India & in future would like to get this serviced in india itself, i would prefer my phone to show India in country!
It honestly doesn't matter. I'm in Canada but I'm using a Latin American firmware. But yes, to get it serviced I guess you need it. How about asking someone with the Indian firmware to dump it for you?
That is precisely the reason i am looking for the indian version instead of UK.
None of my friends have a X10 & strangely, even google dint yield any satisfactory results.
I will opt for the UK update only if Indian update is not available.
Also, i am still not able to open the calender using my gmail account. evertime it says "error! try again later" !!!
raj_5004 said:
That is precisely the reason i am looking for the indian version instead of UK.
None of my friends have a X10 & strangely, even google dint yield any satisfactory results.
I will opt for the UK update only if Indian update is not available.
Also, i am still not able to open the calender using my gmail account. evertime it says "error! try again later" !!!
Click to expand...
Click to collapse
so did you manage to update to a newer firmware yet? you said a while back that "holding the back button" did not work. You need to have the phone off before you do this step.
1. turn phone off
2. connect usb cable to phone, but not to pc.
3. open SEUS and get to the stage that it says waiting for phone connect.
4. press and hold the back button (which will power your phone on in flash mode) and connect the USB cable to pc.
SEUS should now say "stop pressing back button" or something to that effect.
mrtim123 said:
so did you manage to update to a newer firmware yet? you said a while back that "holding the back button" did not work. You need to have the phone off before you do this step.
Click to expand...
Click to collapse
No, it still dint work. i tried it thrice & following all instructions carefully. i had the phone switched off.
1. turn phone off
2. connect usb cable to phone, but not to pc.
Click to expand...
Click to collapse
in SEUS, it says first connect USB cable to PC, then to phone.
3. open SEUS and get to the stage that it says waiting for phone connect.
4. press and hold the back button (which will power your phone on in flash mode) and connect the USB cable to pc.
SEUS should now say "stop pressing back button" or something to that effect.
Click to expand...
Click to collapse
Nothing like this happens in my case. Dont know whats wrong!
Guys, i managed to install Astro File Manager over the air! i did install a few apps to my comp & then to my phone using AFM but not all apps are available to install on the comp! thats the reason i needed Android Market on my phone.
Also, i dont understand why i cant register to google through my phone as i have to use the phone calender.
Guys, it re-installed SEUS & it detected my phone but i again failed! i am dumb!!!
1) Install SEUS (Sony Ericsson Update Service).
You can get it from here: http://www.sonyericsson.com/cws/down...-2.10.6.21.exe
2) Run SEUS, follow the prompts. You don't need to update the phone through it, but get the phone ready for updating. This process should install the drivers necessary for the rooting process.
Note: I suggest you keep your USB cable attached to that USB port. Remember which USB port of your computer it's attached to, as changing USB ports can lead to a bit of confusion for the next 2 steps!
3) To check if #2 was successful, click on Start, click Run, and type: regedit
In the Registry Editor that pops up, click on Computer, press CTRL+F, and search for this: USB\Vid_0fce&Pid_adde\
After it's finished finding, on the right side you'll see DeviceInstance, then it says REG_SZ, then it says something like USB\Vid_0fce&Pid_adde\5&270d2a78&0&3
You'll need that last bit (in this example: 5&270d2a78&0&3 Yours would probably be different). This is your DeviceID (you'll need it soon!)
Click to expand...
Click to collapse
I reached till here & searched for "USB\Vid_0fce&Pid_adde\" but no files were detected!
then i searched for "USB\Vid_0fce&Pid_adde" & i found a file which says-
MatchingDeviceId Reg_SZ usb\vid_0fce&Pid_adde
Thats it! no device ID in front of it!
raj_5004 said:
Guys, it re-installed SEUS & it detected my phone but i again failed! i am dumb!!!
Click to expand...
Click to collapse
Can you clarify, did you get into flash mode for it to install the drivers?
I re-installed SEUS. then I started SEUS, switched off my phone for 30 secs, connected USB cable to computer, then connected USB cable to phone while pressing the back button & kept pressing the back button until the phone got switched ON.
then SEUS asked me to open Notification bar & turn ON USB. i left the back button & did the same. then the screen showed "X10i connected" & your phone is up to date!
then i tried whatever you had mentioned but it was of no use as mentioned in my post above.
Also, SEUS detects my phone only 1 out of 5 times. the remaining times, it takes soooooo long that i have to abort the process & SEUS hangs!
Also, i have noticed that in my SEUS, in the phone models where you have to select your phone, there are two options, both which look like an X10 with names "X10" & "SO-01B". which one should i select? i tried with X10 but failed. then i tried with SO-01B & it dint detect.
You problem is that seus is not detecting your device..
Soln... User a laptop with win xp or vista or 7 32 bit...
Do a complete uninstall of seus. Clean the registry of any seus entries..
Reinstall seus..
Use a different usb port.
Now try..
The device is an x10 unless you your it from japan which if the case is then it is the so-o1.
If you want dump of indian firmware I can help you but I dont think a dump will be of much use to
You..
Chetan
raj_5004 said:
I re-installed SEUS. then I started SEUS, switched off my phone for 30 secs, connected USB cable to computer, then connected USB cable to phone while pressing the back button & kept pressing the back button until the phone got switched ON.
then SEUS asked me to open Notification bar & turn ON USB. i left the back button & did the same. then the screen showed "X10i connected" & your phone is up to date!
then i tried whatever you had mentioned but it was of no use as mentioned in my post above.
Also, SEUS detects my phone only 1 out of 5 times. the remaining times, it takes soooooo long that i have to abort the process & SEUS hangs!
Also, i have noticed that in my SEUS, in the phone models where you have to select your phone, there are two options, both which look like an X10 with names "X10" & "SO-01B". which one should i select? i tried with X10 but failed. then i tried with SO-01B & it dint detect.
Click to expand...
Click to collapse
cvchetan said:
You problem is that seus is not detecting your device..
Soln... User a laptop with win xp or vista or 7 32 bit...
Click to expand...
Click to collapse
Sadly, i dont have a laptop, i am not a laptop person!
Do a complete uninstall of seus. Clean the registry of any seus entries..
Reinstall seus..
Use a different usb port.
Click to expand...
Click to collapse
I tried all the above but in vain!
The device is an x10 unless you your it from japan which if the case is then it is the so-o1.
Click to expand...
Click to collapse
Thanks for confirming that.
If you want dump of indian firmware I can help you but I dont think a dump will be of much use to
You..
Chetan
Click to expand...
Click to collapse
yes, i would like to have the Indian firmware as that would make servicing my phones in India easier!
Can you tell me the disadvantages of having the Indian firmware when compared to the UK one?
I read that even Indian firmware has Android market & even India is getting a upgrade to Android 2.1 along with UK.
I tried using SEUS with different USB port & my phone was detected but again i found no DEVICE ID! the same thing happened which i have written in Post #14.
Is there any other method to find DEVICE ID? i even tried this-
Alternatively, download the file in the next step and extract it, go to the folder called 1st, and run the DeviceID.jar file. It should give your DeviceID
Click to expand...
Click to collapse
It shows a blank screen!!!
raj_5004 said:
then SEUS asked me to open Notification bar & turn ON USB.
Click to expand...
Click to collapse
SEUS doesn't ask you to do that, PC Companion does though. I've never known anyone have such problems getting SEUS to run.
Was trying to Install Backtrack 5 on my X10 and followed each and every step VERY CLEARLY. I m no NOOB so I knew what I was doing.
I m on MIUI 2.2 and while starting the backtrack 5 I got an error which said
1) is ur phone root?
and asked
2) whether I got busybox
So I made a foolish thing of installing Busybox again.
(Somewhere I read that custom roms use their own busybox and there is no need to install other version cuz it leads to boot loop), and Yes the boot loop started on my phone with an error that System force close.
Now my X10 is not detecting my sd card, + Xrecovery is not opening no matter how long I press the back key, + The flash tool is not flashing any firmware to my phone saying TURN ON PHONE AND CHECK USB DEBUGGING IS ON., I turned it on, but it still asks me do that.
OVER THIS ALL THE BLOODY UPDATE SERVICE FROM SONY ERICSSON SAYS NO SOFTWARE AVAILABLE FOR UR PHONE.
If any one can help me how to flash a custom rom from COMPUTER
or If anything using terminal emulator
or how to make my phone read my sd card.
ANYTHING, ANY HELP IS VERY APPRECIATED.
THANKS IN ADVANCE
waiting for help as soon as possible
If you using Zeus to reinstall 2.1 when it tells you that you have latest software already you will have the option to reinstall in the bottom right corner
Kieron
Sent from my X10 using XDA App
but it said Your phone has latest software Installed.
and at the right bottom there was only EXIT button.
and top of it was FINISHED written with a Tick mark
ANymore help
Yours is a very unique case. Try this to go back to 1.6. I dont know if it works. http://forum.xda-developers.com/archive/index.php/t-1103343.html
you are selecting the wrong option its not upgrade that you want
you want to repair and not upgrade.
repair will help you in reinstalling.... to 2.1
Hello, I am a newbie Android user and I have been exploring the greatness of the OS for few days now.
Just now I tried to update my firmware to 2.3.5 and followed instruction from a non-xda developer site and little did I know, it messed up my phone big time.
While I was loading all the files (CSC, tar, modem, etc), and I should've known better when the site told me to check the "re partition" box, but I was stupid enough to go along with it.
So Odin got stuck at re-writing the modem or something like that and I had to pull out the battery from the phone.
Now the phone turns on only in recovery mode and none of the recovery choices work, if I choose one it just shows a little green android with white bordered triangle with an orange exclamation mark in the middle.
I can still access the download mode by using conventional button pressing method, but my phone is NO LONGER RECOGNIZED through the USB so I cannot flash the old stock firmware...
Is there a fix for this? If anyone can help me resolve this issue I am willing to compensate very well in return...
Thank you so much for reading my convoluted troubled story, and I really hope to find some resolution in your wisdom.
If u can't reflash your farmware
Than their is only one option left
give it to the Samsung service center they will repair your phone
Sent from my GT-S5570 using xda premium
I'd be down to do so but it will be hard as I have 4 custom binary flash counter... What can I do as of now?
i dont know if this helps you out buddy but maybe if you read in this thread you might find people that had the same trouble as you..just try and search the thread first and if nothing comes up try and read the first page maybe there you might get an idea on how to unbrick the phone
http://forum.xda-developers.com/showthread.php?t=1075278
Thank you.. But I unfortunately did not follow the instructions that is written there I used an external source which told me to check "re partition" which completely messed up the phone, I think. Thank you for your input, though.
sfoksn said:
Thank you.. But I unfortunately did not follow the instructions that is written there I used an external source which told me to check "re partition" which completely messed up the phone, I think. Thank you for your input, though.
Click to expand...
Click to collapse
i dont want to advice you wrongly but you say you can get into download mode right? if it was my phone i would try and flash again but this time using the proper way to do it....but its down to you my friend i dont want to say do it and it gets worse..
EDIT: apologies i just saw that your usb is not recognised...do you have kies on the background when you flash with odin?
Check this unbricker
android-roms.googlecode.com/files/DREAIMG-RC29.zip
Download DREAIMG-RC29.zip and unzip the file.
Reformat the SD card to FAT32 and copy the DREAIMG.nbh onto it.
Safely eject the SD card.
Put the SD card into your device.
Step 3: Wipe The Phone
Hold home and press the power button.
When you see the image of an ! mark, open your keyboard and press Alt + L if you cannot see any command options.
Do a factory reset by pressing Alt + W or just using the trackball.
When the reset is done, go ahead and hold the camera button and select the reboot system now option with your trackball.
Step 4: Flashing The Phone
Once the grey screen pops up (or the white screen if your phone was rooted with JesusFreke) it will ask you to hit a button to start installing the image…press that button. DO NOT DO ANYTHING TO STOP THIS PROCCESS. It will take about 8-12 minutes.
When the image has completed the installation (it will say completed), go ahead and press the green, red, and menu buttons at the same time. The phone will reboot.
And your done! Your phone is now unbricked!.
If this helps u buy me a HTC sensation.
debsattam said:
Check this unbricker
android-roms.googlecode.com/files/DREAIMG-RC29.zip
Download DREAIMG-RC29.zip and unzip the file.
Reformat the SD card to FAT32 and copy the DREAIMG.nbh onto it.
Safely eject the SD card.
Put the SD card into your device.
Step 3: Wipe The Phone
Hold home and press the power button.
When you see the image of an ! mark, open your keyboard and press Alt + L if you cannot see any command options.
Do a factory reset by pressing Alt + W or just using the trackball.
When the reset is done, go ahead and hold the camera button and select the reboot system now option with your trackball.
Step 4: Flashing The Phone
Once the grey screen pops up (or the white screen if your phone was rooted with JesusFreke) it will ask you to hit a button to start installing the image…press that button. DO NOT DO ANYTHING TO STOP THIS PROCCESS. It will take about 8-12 minutes.
When the image has completed the installation (it will say completed), go ahead and press the green, red, and menu buttons at the same time. The phone will reboot.
And your done! Your phone is now unbricked!.
If this helps u buy me a HTC sensation.
Click to expand...
Click to collapse
Thanks for such detailed instruction! Would this method work if my phone is no longer recognized by the computer though? Please clarify what you mean by "open your keyboard" and the subsequent steps...
Thank you, once again!
sfoksn said:
Thanks for such detailed instruction! Would this method work if my phone is no longer recognized by the computer though? Please clarify what you mean by "open your keyboard" and the subsequent steps...
Thank you, once again!
Click to expand...
Click to collapse
Yeah it althrough works . Try it its helps he to unbrick ma t mobile oncemay be It works on ur phone to
Sent from my GT-S5570 using xda premium
Ah I see. Could you please help me understand what you mean by "open keyboard?" I just don't see how I could open keyboard on my SGS2 when it isn't recognized by my computer... If you could clarify what you mean by that it will be really appreciated!
So from your information provided, you have a stock recovery and your phone is semi-bricked. You can still boot and your computer won't recognize your phone.
Do you have a jig? What firmware did you flash? You could use a jig to reset the flash counter on the phone and return it for warranty saying that Kies messed up while upgrading firmware. If you've flashed the KI3 with the new bootloader then the jig won't be able to clear the flash counter.
EDIT: Maybe an experienced senior member might come and look at this thread and provide some other solution. Do wait!
EDIT2: Try reinstalling Kies and the drivers. Don't give up just yet!
sfoksn said:
Ah I see. Could you please help me understand what you mean by "open keyboard?" I just don't see how I could open keyboard on my SGS2 when it isn't recognized by my computer... If you could clarify what you mean by that it will be really appreciated!
Click to expand...
Click to collapse
I don't think that the guide he posted is particularly for galaxy s2 because he also mentioned a trackball...
but if you can go the settings he mentioned you might find something and lead you.
And if you decide to bring the phone to samsung you might want to have a read at Intratechs Official firmware
thread in (Original Android Development)there you can find a bootloader that you can flash so you can use the jig to reset the counter
edit: wow I also failed to read that your computer can't recognise your phone
anymore....
Have you tried to delete the samsung drivers when you go to
your hardware settings?? and let windows find it's drivers again?
Not sure if this will help. I read somewhere someone else with their PC not really recognizing the phone. Someone else advised to unplug the phone and remove the battery then connect to PC insert battery and put it into download mode.
I could be wrong with the method. Its just from my memory.
Also this may make no difference but maybe removing the sim and SD card. Someone will probably call me stupid for suggesting that though.
I wouldn't try that unbrick method mate. That looks like it is an unroot for an old phone..possible the G1 (AKA HTC Dream).
Thanks for all the help... I have been trying to uninstall the driver and reinstall it but no luck. If I could just get the phone to be recognized I think I will be fine, but I just don't know what to do
Thank you for all the suggestions, please keep them coming!
EDIT: this is the guide I used that messed up my phone.. http://androidflip.com/install-andr...-samsung-galaxy-s2-gt-i9100-installing-guide/
EDIT: Tried to reinstall KIES, no luck. It's like there's nothing on the other side of the USB cord... Not even a sound when I plug the phone in...
If it had been via XDA the instructions are do not do what they are saying .
In Odin Select Re-Partition , Auto Reboot and F.Reset Time
In Odin select these files
For PIT select u1_02_20110310_emmc_EXT4.pit
BIG BIG NO to the above .
As usual some stuff ripped from XDA and some from elsewhere .
My suggestion would be one buy USB jig it hopefully will clear the rom counter and enter download mode .
two in recovery mode go to mounts and storage and format cache data dalvik system and sd card .
Clean phone with nothing on it .Flash stock firmware .
http://forum.xda-developers.com/showthread.php?t=1075278
If PC does not now recognise phone either try another PC or return phone to service centre and say it failed on a Kies upgrade .
jje
Go through the following steps on your PC or laptop:
1. Go to Start
2. Panel
3. Programs and Features
4. Windows features on or off (then a list compiled, this can take several seconds).
5. Then you see a check stand Microsoft. NET Framework 3.0 or 3.5 (if not, tick)
6. Open the sub folders with the + and then be there for the 3 sub folders a checkmark (if not checked, any configuration takes several minutes)
- Windows Communication Foundation HTTP Activation
- Windows Communication Foundation Non-HTTP Activation
- XPS Viewer
7. Then click OK
8. Now start up your computer.
9. Now you choose to uninstall through Programs and Features
10. Also remove the Samsung USB Driver.
11. Then download the latest version of Kies on the Samsung site and install it.
12. Now launch the program Select Samsung and go to the Tools tab.
13. Then click on drivers.
14. Once this is complete close the Galaxy S2 with the USB cable to your computer.
15. If all is well you now have access to your phone via the USB connection.
If there are any questions, you can leave a response below.
I am not sure if this will help but you might want to have a try. I got this
from a Dutch website. I google translated it for you and hoping you wont
have trouble reading it. This is one of the guides posted when some of us
here couldn't connect our phone with the usb cable.
droidluck said:
Go through the following steps on your PC or laptop:
1. Go to Start
2. Panel
3. Programs and Features
4. Windows features on or off (then a list compiled, this can take several seconds).
5. Then you see a check stand Microsoft. NET Framework 3.0 or 3.5 (if not, tick)
6. Open the sub folders with the + and then be there for the 3 sub folders a checkmark (if not checked, any configuration takes several minutes)
- Windows Communication Foundation HTTP Activation
- Windows Communication Foundation Non-HTTP Activation
- XPS Viewer
7. Then click OK
8. Now start up your computer.
9. Now you choose to uninstall through Programs and Features
10. Also remove the Samsung USB Driver.
11. Then download the latest version of Kies on the Samsung site and install it.
12. Now launch the program Select Samsung and go to the Tools tab.
13. Then click on drivers.
14. Once this is complete close the Galaxy S2 with the USB cable to your computer.
15. If all is well you now have access to your phone via the USB connection.
If there are any questions, you can leave a response below.
I am not sure if this will help but you might want to have a try. I got this
from a Dutch website. I google translated it for you and hoping you wont
have trouble reading it. This is one of the guides posted when some of us
here couldn't connect our phone with the usb cable.
Click to expand...
Click to collapse
Thanks, I tried to do this but unfortunately the problem persists... What do you think the root of the problem is? I just dont' get it why it won't be recognized anymore.. I feel like I could easily get it to work if I could just get it to become recognized to flash stock firmware....
EDIT: JJE, I would turn it into the service place but I have custom rom count of 4 And I don't have any USB jigs to work with either.... I am still within the 15 days of the phone purchase day, would they be willing to swap my phone?
BUMP, any input would be appreciated...
I have a SE X10i with standard GB 2.3.3.
I have rooted the phone using flashtool I believe and it was all going well.
I then updated Home.apk in system/app with the new one from the X10S (port from XPERIA S) and when I rebooted the phone it just gets to the green Sony Ericsson logo and hangs.
I started to read a few of the 'how to' here, but I'm not clued up enough to know what my options are and what I should or should do.
I was VERY stupid to think I could just update my home.apk without really understanding what I was do.
So I'm humbly asking how I could recover the SE X10i or how I could reflash a new ROM.
I tried just reinstalling using PC Companion, but the USB connection can not be established.
I thus thought, best ask for some guidance before I make a bad thing worse.
I hope it's OK to ask this question here.
Thank you VERY much for any help.
well the first thing you can try is SEUS
this is used when PC companion fails.
http://sony-ericsson-update-service.en.uptodown.com/
it reflashes sony ericssons stock rom.
and if this fails then i have a question to answer.
what did you do other then rooting your phone ?
be exact and share all info regarding what and how the more info the more people will be able to help
I now see my phone has 'booted'.
I had it connect via USB to my notebook and as it was 'hung' booting I just left it.
The lock screen was displayed and when I unlocked it, the screen was 'black', however the notification bar at the top is visible and effectively active,
It has my 3G data disabler (3Gwatchdog) icon, USB debug, USB connect icon, Wifi and battery indicator.
If I pull the slider down I can see the notifications, saying USB connect, Debug enabled etc.
However, the menu or back buttons do nothing and the screen remains black with only the top notification bar visible.
PC companion now see the phone and says the Software is up to date when checked.
There is the fix option available on the PC companion update check 'pop-up'
--------
The Home.apk I installed was the 'seven' screen one.
http://forum.xda-developers.com/showpost.php?p=23129126&postcount=371
I used File explorer to place it in system/app with wr-r-r permission.
I used Titanium backup to 'delete' the Sony Home [2-0-a-0-20] version as I couldn't locate anything home like in system/app to move elsewhere or find any way of locating the source of the file.
I did do a Titanium backup of the file before I deleted it. I'm not sure if the delete retains the backup of the 'home' app file?
http://www.theandroidsoul.com/download-new-sony-ericsson-home-launcher-apk-v2-0-a-0-20/
Is the previous home app I had and have now deleted...Doh!!!
Now probably did another dumb thing, cause the phone 'booted' via USB connection, I thought maybe it'd boot OK albeit slowly normally, but 15minutes later and the Sony Ericsson green logo is still on the screen with nothing visibly happening.
I don't know how long I had it connected via USB before it became 'active' so I can't tell if I should wait longer or if I should attempt some sort of 'fix'/rebuild via PC companion if I can get USB connected again.
Thank you for your help.
[Update] Took about 30minutes, but it showing the lock screen.
Clock in the centre with day/date, unlock or mute sound at bottom and 'standard' notification bar at the top of the screen
Not going to touch it, till I have a plan
well what i understand from the links you gave me is that its simply installed as you would any application.
while the phones running and when pressing home button it would give you the option to go to
A- your 5 page home
B- your 7 page home
and after that tough it doe not mention this
you could i suppose delete the 5 page home.
anyways your scared to tough your phone now huh
from reading your last post i cant seem to find you trying the SEUS option (not pccompanion)
heres a guide!!
http://www.esato.com/board/viewtopic.php?topic=171599
this brings you back to the original software (as you updated to 2.3.3 i believe bin a while )
so all i can say is somewhere something went wrong try your phone now see what its doing etc if its ok (GREAT) if its not try SEUS to get your phone back to the way it was and try again or keep your 5 pages
Was wondering if there was a third way, but I'll get onto a recovery and start over.
I was just using PC Companion as a known reference point to identify the phones possible state of connectivity (or lack there of)
So SEUS, here I come...
Thanks again.
[Update]
All back up and running.
Just doing a few benchmarks on a fresh install while battery recharges and before I 'root' the phone again and reinstall everything.
Next time I'll get a change control approved by mum before I start tinkering
try installing it as a normal app this time and see if you can acces it with your home button instead of replacing
Bjornlindekens said:
try installing it as a normal app this time and see if you can acces it with your home button instead of replacing
Click to expand...
Click to collapse
Nope, too scared.
I have to reinstall cifsmanager, samba filesharing and OpenVPN... so, like I've had enough excitement for one week.
One thing that drove me nuts was (re)rooting the Sony Ericsson XPERIA X10i using Flashtool (like just now). After many false starts on Win7 I found that the USB driver SEMC HSUSB normally fails even using Gordon Gate and etc. As an alternative I used Windows 8 and it 'seems' to install a driver which even asked for the specific model of phone (x10, X10 mini, Arc...etc) and everything worked from then on. I've read(cause I was looking for answers) many queries related to Flashtool and USB SEMC connection drivers, so Windows 8 for some people may be an answer.
But, hay, I've learnt how to crash and rebuild my phone so my fear of the unknown may subside over time.
You wouldnt believe how many times i scratched my head thinking "oh dear you broke it this time for good "
Especially when i booted i got a phone image with a triangle sign!?
But in the end reflashin saved evry time!
Sent from my x10 using xda premium
Hi all,
I have a Lumia 710, with an unlocked Qualcomm bootloader. Yesterday accidently while flashing a rom as the NAND Disk Drive, whilst doing that i 'didn't' select the OSBL mode & the one beneath it which says W7 Qualcomm, before flashing it. Now it got flashed but the problem is its stuck to one rom. The App deployement tools gives errors such as 'make sure the phone is booted' even though its booted & fine. Or the other error it gives is 'request rejected by host machine'. When connected to Zune i now get pop up from Zune stating 'we can't create a connection from your phone to the internet' now this comes up all the time. I can sync stuff but can't deploy stuff or flash stuff
When i did try flashing the same rom again. After flashing it started directly at the livetiles screen as if nothing happened. I was expecting the 'Welcome to Lumia' screen. Please tell me whats happening. Also i was able to flash another rom on it. However still Zune gives the same error when connected so does the Deployment Tool. I can't figure out what can be done to solve this. I suppose the bootloader might be affected. How do i refresh it? I thought about going to Dload & then Back to Qualcomm. But it seems that many people have bricked phones trying to goto Dload from Qualcomm.
I want my Lumia to be unlocked, but more over, i want it working fine...
Any help & info is appreciated, Thanks
try going back to DLOAD..or do a hard reset to your phone and flash another Custom ROM again.
wen u connect the phone..open device manager and uninstall the drivers..reconnect in same mode..let the drivers reinstall.
surya467 said:
try going back to DLOAD..or do a hard reset to your phone and flash another Custom ROM again.
wen u connect the phone..open device manager and uninstall the drivers..reconnect in same mode..let the drivers reinstall.
Click to expand...
Click to collapse
I followed your instructions... Heres what i did...
Step I: Performed a Hard Reset using the Vol Dwn + Camera + Power Up keys.
Step II: Turned the Phone off & connected the phone with Vol Up + Usb connect. Theres an asterisk sign on Qualcomm CDMA Technologies MSM (I had it uninstalled prior to the reset using the Device Manager, It was detected whilst i connected it in Nand mode again)
Step III: Flashed a new rom on it. Lumiatrix v4.3. Still Zune is giving the same error & Application Deployment is not yet possible.
Surya there are three things i need to ask you.
1. In your Noob Guide the rom flash part you are asking people to turn On their phone, select Nokia Connectivity Mode & then select the .nb file & click Write Os. When i try that it asks me for a Nand Drive.
2. If i should try going back to Dload (can i switch to Qualcomm whenever i feel like?), can you please suggest me a clear & concise method, as to how to do it. I wanted to try this (http://forum.xda-developers.com/showthread.php?t=1702815) but its too confusing.
3. Is a bootloader refresh possible? I connected my phone when it was On. I got the Nokia Connectivity Mode. I tried installing the bootloader it found the phone but wanted me to be in the flash mode. However, when i enter the Nand mode it never finds my phone except when i Write Os on it.
I know i have a long list of questions. Its only because of the fact that i want to understand this better. I dun wanna end up bricking my phone. Thanks in Advance. Tc & Godbless!
Ok..wen u connect your phone to the PC while its ON, its in normal mode...the moment u turn on NSS, it will change modes, so it doesnt matter unless u click WRITE OS, which switches the phone OFF and puts it in the NAND dDrive.
as you have a 710, you can try going back to DLOAD and flash a Stock rom and see if that works, and then you can always go back to a qualcomm by my guide.
your at no loss , unless the problem you have a more complicated than we think it is.
surya467 said:
Ok..wen u connect your phone to the PC while its ON, its in normal mode...the moment u turn on NSS, it will change modes, so it doesnt matter unless u click WRITE OS, which switches the phone OFF and puts it in the NAND dDrive.
as you have a 710, you can try going back to DLOAD and flash a Stock rom and see if that works, and then you can always go back to a qualcomm by my guide.
your at no loss , unless the problem you have a more complicated than we think it is.
Click to expand...
Click to collapse
i would try going back to Dload. However, can you please suggest me a clear & concise method, as to how to do it. I wanted to try this (http://forum.xda-developers.com/show....php?t=1702815) but its too confusing.
Are you suggesting using NSS Bootloader Restore? If so, is there a mode that i need to be in? I'm using NSS 0.51b & when I click on restore it brings up a very scary warning message. As I don't want to brick it, i haven't used it yet.
Please suggest me a method... to return to Dload