Hi,
I was on last gsmleak ICS :
- Blur_Version.651.167.26.XT910.Retail.en.EU_2
Battery draining too fast so i reboot in recovery and wipe to factory (bad idea) --> phone never boot anymore
Now i can just access to apfastboot and recovery
But i when i try to connect my phone to pc in AP FASTBOOT nothing can be detected on pc so RSD can't work and fla**** with adb same "no device found" ... (i tried another pc same pb, install again drivers no change)
I tried to put the phone on BP SBF FLASH my pc detect and install drivers but rsd can back to APFAST and flash xml
I tried to flash in recovery again the Blur_Version.651.167.26.XT910.Retail.en.EU_2 but there is error when it verify
assert failed ... kindle.apk (freezed with titanium)
ap fast boot info : 0A.74 device is locked Status Code : 0
Battery Ok Ok to program Connect USB Data Cable
So now i have no solution if anyone can help ... maybe another way to flash something or a file to use with recovery ?
t.y
No help
i tried to flash again the last ota, but there is error because i disabled some apps with titanium like kindle.apk
is there a way to flash this ota wo verify check ???
http://forum.xda-developers.com/showthread.php?p=26915046
Follow Post Nr. 6 (T-Mo to Retail)
Sent from my XT910 using Tapatalk 2
I can t my ap fast boot mod seem to be unavailable, pc don t detect the phone when it s connect
So i cant use rds and adb cmd :/
tel is not detect on pc (i tried different pc cable and drivers without success)
So no idea?
gonna send it to sav but i have got doubts :/
same problem here.. no solution still.
No solution i confirm, i send it to an official moto repair but when i read their check i refused to pay for it :
- motherboard replacement
- speaker and screen have to be change
- and flash
= +140€
and i have to pay +27€ to get back my phone
i m gonna send it to another repair we ll see
http://www.youtube.com/watch?v=WBySMO8n1r4
have u tired ths link??
Related
My phone is not booting up.. What has happened to my cell phone.??
I did not do anything for this to occur It was actually ON. I had not restarted or even shut it down when i used it few mins back.. When i returned to it now it was showing the Boot screen, I had no idea of what to do. Just removed and re-inserted the battery.
Now the Phone gets stuck at this command as below !!
Fastboot mode started
udc_start()
--suspended --
What to do.? Please Help.
http://forum.xda-developers.com/showthread.php?t=1088046
I am using the OpenOptimus Rom 2.202.1 and clockworkmod recovery.
The Mobile was in charging state when this happened. It noticed it was in boot screen so i removed the charger and then removed the battery and restarted.
Now should i reflash usign KDZ or is it possible to revive my system back to normal without reflashing.??
clawsright said:
I am using the OpenOptimus Rom 2.202.1 and clockworkmod recovery.
The Mobile was in charging state when this happened. It noticed it was in boot screen so i removed the charger and then removed the battery and restarted.
Now should i reflash usign KDZ or is it possible to revive my system back to normal without reflashing.??
Click to expand...
Click to collapse
follow the link provided by sweetnsour u will get ur phn back to life
I followed the steps given on that thread
My pc shows new device found ANDROID. Device is not getting detected
But on this step in cmd
fastboot erase recovery
it shows < waiting for device >
i too got such problem.
while holding down back +Vol down connect your phone to pc .It will enter into emergency mode.Then your Computer might detect it.
Can anyone of u help me ???? My phone is still stuck with Fastboot mode
Basically on a windows machine you download kdz updater and uncompress it as it is a zip file.
Download from here.
This is what I did on an xp laptop.
I had to down load the drivers from the official lg site. when here you enter the code that is on the box the phone came in or under the battery.
Chose the your county and laguage from the drop down box at the top right of the dialogue box. Then from the middle you can choose the drivers. For some reason I had to find the files and click on them to install the driver.
Ok once you decompress kdz updater there are three seperate files to work with. 1. windows enabler. 2. msxml.msi 3.KDZ_FW_UPD.exe
You will also need to download the right file to restore with,You can find it with google.
Please check here the The_ERROR thread wich explains it very well:
[ROMS] Original LG Firmware list.
Install msxml now.
Now you have to boot the phone into rescue mode. On Lg Optimus One turn phone off even if it means taking out the battery.
Press power - volume up - back (this button is next to the home button).
Connect to usb now.Computer found new hardware and installed four drivers.
Then open device manager. Left click my computer - properties - device manager. You need to disable the lg modem driver. Left click on it and disable.
Now launch kdz updater. There will be a drop box on left set to 3gspt or similiar. on the right drop box set to diag. The long box just above the info box with a file at the side lets you browse to find restore file. e.g. V10a.00.kdz.
Double click the button below and let it do it's thing. Took 15min. My phone shut down and came up with an error at the last minute. Anyway I rebooted and all was good.
Everything was the way I left it. Just had to re-root.
My only real problem was getting the kdz installer to see the phone.
After installing the drivers restart pc. If it finishes quickly and just before saying finished it says phone not found try removing all phone related drivers including nokia pc suite and the lg suite and remove and reinstall the drivers.
Hope this is of some help to you.
Finally, Recovered my phone by flashing KDZ through Emergency mode.. No other method worked..
clawsright said:
Finally, Recovered my phone by flashing KDZ through Emergency mode.. No other method worked..
Click to expand...
Click to collapse
I told you. Nothing else would work.
royal.tarun said:
My only real problem was getting the kdz installer to see the phone.
Click to expand...
Click to collapse
I had the same worries coz my pc did not detect my device at all..
I was trying to get pass the Fastboot mode.. But in the cmd when i tried to erase and re-install recovery it said waiting for device.. Luckily and finally after many tries i could enter emergency mode. Only then the phone got detected but fastboot didnot work there.. The Only way out was to Do the KDZ flash. I flashed the indian GB V20b and did a hard reset now. Flashed recovery and for now have left it with the stock rom..
I wonder now this problem arises due to custom roms.
---------- Post added at 02:03 PM ---------- Previous post was at 01:59 PM ----------
Is the fastboot mode the so called "Brick-ing" of mobile device.?
clawsright said:
I had the same worries coz my pc did not detect my device at all..
I was trying to get pass the Fastboot mode.. But in the cmd when i tried to erase and re-install recovery it said waiting for device.. Luckily and finally after many tries i could enter emergency mode. Only then the phone got detected but fastboot didnot work there.. The Only way out was to Do the KDZ flash. I flashed the indian GB V20b and did a hard reset now. Flashed recovery and for now have left it with the stock rom..
I wonder now this problem arises due to custom roms.
Is the fastboot mode the so called "Brick-ing" of mobile device.?
Click to expand...
Click to collapse
this problem was cuz didn't perform the steps carefully.
This can called bricking but not fully . As it can be recovered.
Bricking is when your phone is as useless as a brick.
Hello friends, I need your help to solve my problem, I tried everything to recover my phone, and it still fails.
I installed CM9 on my xt910 room, and every time I turn on my device, it does not charge and does not leave the boot screen, I've tried clearing the cache for recovery, and tried to recover back to the original room using RSD, but when AP Fastboot put in, it appears on the screen:
AP Fastboot Flash Mode (s)
0A.74
eMMC Info: Size 16G
To return to normal mode - firts press power key to power down
Device is Locked. Status Code: 0
Baterry OK
OK to Program
Transfer Mode:
USB Connected
And when I try to flash by RSD Lite, of this error
failed flashing process 6/18 flash cdt.bin "cdt.bin" -> Phone returned fail .
U hv to download n try another file n flash again with rsd.(depend on your region)
Sent from my XT910 using xda premium
I've tried, I can not find a solution to fix my problem, help me!!
Hi there! An update of CM11 failed on my xt910. The result was the laying Android an no normal Boot was available.
While downloading RSD and stockroms ( SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTCEE_HWp2b_Service1FF_fastboot and SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_Service1FF_fastboot from motorola ) the battery drained in the bootloop.
Finally I was able to select the fastboot option in the bootloader menu but the program printed "Battery low"
After some research I crated a factory cable.
Now the battery is ok and I was able to flash via RSD.
But in RSD I always get the error that the flash failed. (Phone returned FAIL)
I don't know what to do now. Some ideas?
Razr xt910 driver installation
Hi I am having XT910 Razr, ICS with 673.94.328.xt910.asiaretail.en.03 firmware. Now I have two problems 1) battery sucks and 2) USB drivers failed to install. So am not able to root or change the firmware. I have tried everything but failed. have downloaded the blur version of the same firmware but in the recovery mode it is showing signature verification error. Service center is also not able to help me and asking a huge money. Can some one help me on this.
Hi amit81276. You should open a new thread for your specific issue. If you give detailed error messages or behaviour I may could help.
1) battery - if the battery is too low to flash ("Battery Low" message in bootloader ap fastboot mode (access bootloader through power + vol up + vol down (to turn off and enter bootmenu))) you have to make a factory cable that allows you to connect the phone while powering it.
2) I have trouble with the drivers too. Install the Motorola Device Manager. Use C:\Program Files\Common Files\Motorola Shared\Mobile Drivers\Motorola Driver Installer.exe and bruteforce the driver to be installed. (Open the Device Manager to ensure the Mot Driver is running properly) (Sometimes I had to Clean&Install 10 times, reboot, use other USB port - very annoying)
Later I switched to another PC and there was no trouble at all.
BTT
I was able to fix the phone now. The problem was that http://sbf.droid-developers.org/ only offers 4.0.4 sbf for xt910. But I remembered that my phone was on 4.1.2 - so I was able to find the sbf on a thread here on xda ->
RAZR XT910 Firmwares SuperThread (Jelly Bean)
Remember:
Failed flashing process. 1/10 flash cdt.bin "cdt.bin_signed" -> Phone returned FAIL
Failed flashing process. flash system "system_signed" -> Phone returned FAIL
Failed flashing process. flash boot "boot" -> Phone returned FAIL
should indicate you that you are trying to flash a wrong / lower version ROM. (a downgrade won't work but in special cases)
I suggest try flashing with moto-flash! It uses fastboot which gives you real errors instead of "Phone returned FAIL". For example it returns Battery low if the battery is too low and it won't flash! Very useful to find errors! In my case the error was always 1/19 flash mbm "allow-mbmloader-flashing-mbm.bin" -> Phone returned Fail that's not usefull at all.
Guys, excuse my English, the text was translated by google translator
*
I have the following problem in my european razr XT910
*
Accidentally deleted the boot menu manager and now the phone does not start at all. With much sacrifice unable to flash the original rom on my device .
*
The problem is that I did not back up the cid of the device and therefore the device is locked on the home screen with that error message CustomerID error,Contact Dealer Boot to Suspend/TCMD
Just going into recovery mode with the system usually start by selecting the BP Tools . And the system works normally.
*
From what I read, when you do not have the CID of the phone and you have to get the BP Tools (That was my case ) to start . The problem is that when I walk by BP tools it loses communication with the computer USB . Whenever I plug in the cable to the USB port appears the warning on mobile : " AT Command Service Stop ."
Because of this , it is not possible to Root to reinstall bootmenu manager .
Would know tell me if there is any procedure so that it returns to start normally without the need to enter the BP Tools?
*
If not, is there any way to install any CWM ?
thank you
I have the same problem, what can we do? Custom recovery can do something?
Sent from my Nexus 5
joaovictorssa said:
Guys, excuse my English, the text was translated by google translator
*
I have the following problem in my european razr XT910
*
Accidentally deleted the boot menu manager and now the phone does not start at all. With much sacrifice unable to flash the original rom on my device .
*
The problem is that I did not back up the cid of the device and therefore the device is locked on the home screen with that error message CustomerID error,Contact Dealer Boot to Suspend/TCMD
Just going into recovery mode with the system usually start by selecting the BP Tools . And the system works normally.
*
From what I read, when you do not have the CID of the phone and you have to get the BP Tools (That was my case ) to start . The problem is that when I walk by BP tools it loses communication with the computer USB . Whenever I plug in the cable to the USB port appears the warning on mobile : " AT Command Service Stop ."
Because of this , it is not possible to Root to reinstall bootmenu manager .
Would know tell me if there is any procedure so that it returns to start normally without the need to enter the BP Tools?
*
If not, is there any way to install any CWM ?
thank you
Click to expand...
Click to collapse
The same here boss i don't know what to do but i found a cid in my computer but i don't want to lose this room it is jb and very cool hope some one answers us
So many people w this problem and not a single solution.. Can i flash a custom recovery vía stock recovery? What can i do of i sont have ap fastboot?
Sent from my Nexus 5
franstorm said:
So many people w this problem and not a single solution.. Can i flash a custom recovery vía stock recovery? What can i do of i sont have ap fastboot?
Sent from my Nexus 5
Click to expand...
Click to collapse
I have the same issue, try this (doesn't work for my... maybe you can).
http://forum.xda-developers.com/showthread.php?p=52131160
Hi all, I'm new in this forum but i read a lot of your thread in order to learn about android phone.
First of all, sorry for my bad english.
I have a problem with my razr maxx. I bought it on ebay (a used one). I use Razr/Maxx XT912 (Matt Droid Razr Utility) and now the phone is in bootloop.
This is the error message:
invalid flash mode (s) (boot failure)
0A.77
emmc info: seize 16gb
Device is LOCKED. STATUS CODE 0
battery ok.
ok to program
transfer mode:
usb connected
AND
Invalid cg otv (CG:system): invalid sp data
invalid cg version (cg:system)
invalid cg otv (cg:system)
I'm trying to resolve with this old thread http://forum.xda-developers.com/showthread.php?t=1524011
My phone model is xt910 type name m0c2e fcc id : ihdp56me2 ic id 109o-p56me2 and it has verizon apps. (i red the it on the back of the phone) BUT I also use the imei in the motorola's support to find out the model of the phone, and this is the answer: XT912 (Spyder LTE) (i also find a screen of the phone with some info -> see the attachments ). [the phone is only with motorola brand].So which is the right model? I also have (or better had) supersu already on it. I use it with a sim card (i use it with in gsm mode but it has also cdma mode. The languages are only spanish and english )
I arrive at this point ( from this "guide" http://forum.xda-developers.com/showthread.php?t=1524011) http://forum.xda-developers.com/showthread.php?t=1362956 but i don't know which one i must download.
ps.
i also tried:
1-download cdt.bin ( http://www.mediafire.com/?ua1nj6ds6r0vtue )
2-download fastboot files ( http://dfiles.eu/files/bih3tmg7b )
3-restart your phone in to bootloader ( fastboot ) mode
4-connect your phone via usb cable
5-open cmd.exe in your pc an go to fastboot files
6-flash cdt.bin via this command -------------------------------------- fastboot flash cdt.bin cdt.bin
7-restart your phone in to stock recovery
8-do triple wipe and restart your phone
and you can see the result in the attachments..
What can i do in order to resolve the bootloop? I'm desperate
Thank you
Hi!
Flash this rom with RSD Litehttp://sbf.droid-developers.org/download.php?device=9&file=788
Let me know if worked. You battery may be drained by this time, if so, you'll need to use a factory cable.
But, let me know if you could flash with RSD Lite first.
Cheers
i'm trying but it failed. (usb error at status 22/24 and 18/24). Now i repeat the action. I have the original cable and the phone is in fastboot flash mode
It's working ! THANK YOU!!!
In order to avoid the same problems, How can i change rom? (which one can i use ?) Which programs and apps do i need to use? Where i can find a guide? Which is the best way in order to improve the gsm signal?
Thank you,
Roncallica
An other idiot question. Now it is without supersu and it is locked. What can i do?
roncallica said:
An other idiot question. Now it is without supersu and it is locked. What can i do?
Click to expand...
Click to collapse
Hi!
Glad it's working first place. You'll find all you need just navigating throught the Development section. You have a root method easy to use to your phone, a safe to use recovery and a lot of kernells and roms to pick up onde of your choice.
Before doing anything like flashing roms or installing things be sure you've charged you phone, always. Remember Razr battery are not removable, so, if you brake it while doing some stuff you need no return to your previous rom and start all over again.
First step now? Root this thing!
Cheers
Do i have to use this guide? I mean in order to root xt912 http://forum.xda-developers.com/showthread.php?t=2230140 or can i use this one? (http://www.youtube.com/watch?v=YIEO0pedtzE). Can i modify kernells and radio in order to obtain more gsm signal? i don't find a safe recovery for xt912 spider, what can i do? I have some problems with internet and it's a bit slow
thank you!
Having a simillar problem with my XT910, when I power it on it doesn't boot but goes straight to the error message saying
AP Fastboot Flash Mode (S) (Recipe Failure)
0A.77
eMMC Info: Size 16G
To returno to normal mode - first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OK to Program
Connect USB
Data Cable
If I try to flash ROM via RSDLite, it recognizes the phone but I got flashing error on the first step. If I press power to shut it down, then VOL+/- with Power key, and select Normal Powerup, in more than 90% phone goes to a bootloop, sometimes it boots normaly and then everything works. If I select BP HW Diag & Boot AP, it boots every time but when I try to connect it my PC asks for some drivers for Diag and so which are not installed on PC and the phone won't charge a battery when connected to a charger - everything else is working.
Phew, that was a long post! :laugh: Any idea what might be a problem?
I forgot to mention that I bought the phone in this condition so I don't have a clue what a previous owner flashed (or tried to flash). Android version is official 4.1.2, system version 982.124.14.XT910.Retail.en.EU, build number 9.8.20-124_SPUEM-14.