Need original img <3e> recovery for ViewPad7, pls help - Viewsonic ViewPad 7 & Variants
Hi there, I'm new here and I need your help.
My ViewPad7 haven't an original <3e> recovery because i get it from another and it run cooked rom.
Now i want to back to the stock rom following here: http://forum.xda-developers.com/showthread.php?t=1601117 but it need an original <3e> recovery.
Could you kindly help me to get it, if you have a backup of original <3e> recovery from your ViewPad7, please send it for me.
Or you can backup your stock recovery follow this guide: http://forum.xda-developers.com/showthread.php?t=1015005 then help me.
Thank you so much. Sorry for my English.
Anyone, please help?
For Vpad7 - do you have the "older" non-ITE or "newer" ITE (multi-touch) screen - original/stock recovery image file or whatever?
If you aren't sure - post your Vpad7's production date, which is on the printed label on the back as that should help ...
I don't know about the 'non-ITE' or ITE screen of my device. Its production date is: 28-4 2011
Please help me!
Thanks Letitride
Based on device's production date, it's "most" likely an ITE device (there is nothing certain or definitive about it ...)
Okay, calvary to the rescue for fellow XDA's.
AS - please check your PM too (you got mail ...)
Letitride said:
Based on device's production date, it's "most" likely an ITE device (there is nothing certain or definitive about it ...)
Okay, calvary to the rescue for fellow XDA's.
AS - please check your PM too (you got mail ...)
Click to expand...
Click to collapse
I'm having the same problem here. Letitride can u help me out also?
Lanfear28 said:
I'm having the same problem here. Letitride can u help me out also?
Click to expand...
Click to collapse
Have you read the following thread & try it to see if you can restore your device ?
http://forum.xda-developers.com/showthread.php?t=1601117
If not or it failed, please be a little more specific about your issues and error messages/description of bootup problem, etc. ?
sadonsu assailants
I have the cwm recovery and cant get back the original <3e> recovery to flash the original Viewsonic firmware(v3_420)
@Letitride
Works like a charm
Lanfear28 said:
I have the cwm recovery and cant get back the original <3e> recovery to flash the original Viewsonic firmware(v3_420) @Letitride ... Works like a charm
Click to expand...
Click to collapse
Restored & working w the "alternative" *.img as referenced in PM then, excellent & enjoy the Vpad7 - only wished it's a bit faster, overclocking or whatever. But, it is what it is and loved the 7" factor, much easier to slip into a pouch, pocket, jacket, etc. to take along.
Is there anybody with original Viewsonic firmware(v3_420) and with working internet thru mobile data?
i got the viewpad7 back to original with stock recovery that i extracted it from stock rom, thanks
Hello, sorry for bumping this thread but it is relevant to what I need.
EDIT: Moving to thread for visibility.
I recently rooted my Viewsonic Viewpad 7 and put on a custom ROM. I noticed that wifi was not working so I tried some fixes, which none of them worked. One of those fixes involved formatting the sd card. After formatting, I realized I made a huge mistake as my backups are now all gone.
So I have the clockwork recovery installed (v5.0.2.6) and I think it is causing problems. I tried using Software Update Tool L3 (SUT L3) in order to restore the firmware back to normal using the .nbo from the Viewsonic site but I think I need the original <3e> recovery. Whenever I try to recover using the tool, it reboots the device into Recovery mode and after a few minutes I get the error:
Error Code: 0xc60e
Error: Download fail,
Error = SE_ERR_SUT_DETECT_DEVICE_FAIL (0xC60E).
I believe this is because it is expecting the original 3e recovery and doesn't recognize the clockwork recovery. I tried to find a copy of the original recovery.img but I can't find it online anywhere. This thread is the closest I've gotten. Please let me know if there is anything I can do to fix this. Or if anyone has a copy of the original 3e recovery, it may help me out.
Thanks!
FTM Mode Info:
SWVer=3.240
MODEL:FM6-0001
HWVer:107
clandor said:
... rooted my Viewsonic Viewpad 7 and put on a custom ROM ... So I have the clockwork recovery installed (v5.0.2.6) and I think it is causing problems. I tried using Software Update Tool L3 (SUT L3) in order to restore the firmware back to normal using the .nbo from the Viewsonic site but I think I need the original <3e> recovery. Whenever I try to recover using the tool, it reboots the device into Recovery mode and after a few minutes I get the error:
Error Code: 0xc60e
Error: Download fail,
Error = SE_ERR_SUT_DETECT_DEVICE_FAIL (0xC60E).
I believe this is because it is expecting the original 3e recovery and doesn't recognize the clockwork recovery. I tried to find a copy of the original recovery.img but I can't find it online anywhere. This thread is the closest I've gotten. Please let me know if there is anything I can do to fix this. Or if anyone has a copy of the original 3e recovery, it may help me out.
FTM Mode Info:
SWVer=3.240
MODEL:FM6-0001
HWVer:107
Click to expand...
Click to collapse
Are you using the "correct" factory *.nbo file with SUTL3 (which ver.) as it looked like your model is likely an ITE (newer) model ?
Can you boot the device into CWM Recovery mode now? Does it start up with the VS Android boot animation?
I will have to look for my backups as I've them on a backup server somewhere and/or in cloud storage ... will look & see what I have?
Haven't flash/done any factory restoration work on the Vpad7 in over a year+ now but, as I recall, flashing the *.nbo file via the PC with the factory update utility will wipe the device clean and restore it to factory fresh, locked mode so it should NOT matter what recovery you have on the device now.
Please describe in greater details the steps you took in trying to restore ... it's still a joy to go back to the Vpad7 but hard to let go of the new Nexus 7 quad-core "toy" these days for me ...
Thank you for your help.
I am pretty sure it is an ITE model. It's HWVer is 107, and I used this thread to help figure that out.
I downloaded firmware (.nbo) v3_420 and v3_62 from here. (Under Downloads > Drivers)
Here are the steps I took in order to try and restore.
I started off by enabling USB debugging and plugging in the tablet.
I opened up SUTL3 v1.7.9 and selected one of the firmwares (both yield same result). The update option I set to Erase user data. Once I hit next, it says Updating the Phone software, please wait.
The device restarts into recovery mode. The recovery menu title says CWM-based Recovery v5.0.2.6 which is a custom one I changed. I do not know how to get it back to the original as I have lost the backup.
After about a minute or so, I get
Error code: 0x4000
Error: Download fail,
Error = DEVICE_NOT_CONFIGURE (0x4000).
At this point when I retry using SUT L3 without leaving the recovery mode, I will only get the error from the previous post.
I'm not sure what my options are but my goal is to get back to the original ROM or get wifi working again on the current ROM. The current ROM I am using is CleanView Ice v1.3. I tried both the ITE version and non-ITE version and there seems to be no difference.
The only thing I seem to be able to do is Install ZIP from sdcard which lets me switch between custom ROMs but it doesnt fix the wifi problem or let me go back to original.
---
Edit: I tried doing the same thing a few more times with my antivirus disabled and it's still the same.
Also, I'm not sure if this will help at all but I tried to use the Synchronization tool that shows up on the PC when plugging in the device. It gave me the error "Can't access data on handheld! Please check the connection between desktop and handheld and at least enter Contacts once if you just clear your data!" These may be related as I have accessed Contacts and even added one in to test and this error comes up every time.
Maybe some kind of driver problem?
clandor said:
I am pretty sure it is an ITE model. It's HWVer is 107, and I used this thread to help figure that out.
I downloaded firmware (.nbo) v3_420 and v3_62 from here. (Under Downloads > Drivers) ... Maybe some kind of driver problem?
Click to expand...
Click to collapse
Okay, let's see - yours is ITE (UK-based) and running the same firmware as mine (USA) and v3_62 will work too, mine is on v3_420.
You still have working CWM 5.x on your device and can boot into it (small pin hole on the button to reset, etc.)
Okay, a # of points - the SUTL3 is run from the PC together with the *.nb0 file - running Windows XP or Vista, go the Command Prompt - Vpad7 drivers are already installed, give it a try - does it work as that will restore it to factory state - it should not need the Stock Recovery to flash it (I could be mistaken as it's been a while) Unpack the Zip file so that the utility will read the *.nb0 file directly.
First suggestio, however, is that if you have working CWM - my recommendation would be to flash from custom recovery, EUv1.7-ITE firmware in Zip file format - as linked here in Dropbox account of mine, OP/developer's link is no longer accessible or available. https://dl.dropbox.com/u/64025118/EUViewpad7v1.7b-ITE.zip
Download & transfer to mSD card, reboot into CWM, wipe dalvik cache, cache & system/full reset - then, flash the zip file and it should be done in about 10 minutes, be patient and go thru the Setup - if all goes well, your ITE device is back to life again. This is my preferred ROM and WiFi works well, if necessary - do a Master Reset again from the running Rom if necessary, reboot once & then setup your WiFi again.
Turn-off Antivirus & Firewall on the PC while flashing ... let me know whether you can get into the EU Rom as it will save you the extra work of going stock and rooting, etc. if your original challenge was just trying to get a good WiFi signal.
The previous times that I tried to install the .nbo files with SUT L3, I extracted them from the zip.
Also, I got firmwares on the UK site but I am Canadian. Most likely mine is also USA-based as many of our electronics are. I just could not find the files on the USA site.
I am running Windows 7 so some drivers installed automatically. I did use Setup.exe to install some other drivers but I have noticed no difference between the two times. Running setup.exe doesn't install anything anymore.
--
Here are the steps I took after your post:
I first transferred EUViewpad7v1.7b-ITE.zip to the microSD card and after rebooted into CWM-based Recovery. I wiped Dalvik cache, cache and "data/factory reset". I then flashed the .zip file and restarted the device after it finished loading.
I noticed the new intro logo so it seems switching the new ROM was a success.
I went into wireless and network settings and I turned on Wifi in the Wifi settings. The device scans for networks for about 30 seconds, then stops and displays "Unable to scan networks" and turns off.
I know for sure there are networks in the area and the wifi was working before I swapped to another ROM.
This is where I am currently stuck.
Again, thank you for your help.
clandor said:
... Most likely mine is also USA-based as many of our electronics are. I just could not find the files on the USA site. I am running Windows 7 so some drivers installed automatically. I did use Setup.exe to install some other drivers but I have noticed no difference between the two times. Running setup.exe doesn't install anything anymore.
--
Here are the steps I took after your post:
I first transferred EUViewpad7v1.7b-ITE.zip to the microSD card and after rebooted into CWM-based Recovery. I wiped Dalvik cache, cache and "data/factory reset". I then flashed the .zip file and restarted the device after it finished loading. I noticed the new intro logo so it seems switching the new ROM was a success.
I went into wireless and network settings and I turned on Wifi in the Wifi settings. The device scans for networks for about 30 seconds, then stops and displays "Unable to scan networks" and turns off. I know for sure there are networks in the area and the wifi was working before I swapped to another ROM. This is where I am currently stuck ...
Click to expand...
Click to collapse
Great, that's major progress - first, let's check & verify a few things and do it step-by-step:
Go to Settings - About phone - check that the following is same or similiar (they should be identical or almost)
Android 2.2.2
Baseband PR3.7_125
Kernel version Apps_2.6.32.9
Build number 4027_3_420
Check under Mobile network settings -
Data enabled (it should NOT matter, only if you are using a Sim card for voice and/or data in Canada)
Under WiFi settings -
WiFi - enabled, cycled it OFF and ON again, does it see various open and/or secured networks nearby
If NOT, press the soft "Menu" key on the lower right (in landscape mode) - it should open up & show "Scan" & "Advanced"
Can you do a manual "Scan" - make sure you have a known working WiFi, either secured or open (McDonalds/Starbuck or public library, etc.)
Next - open "Advanced"
Wi-Fi sleep policy (mine is set to "Never when plugged in" - try to temporary set it to "Never" for this purposes
MAC address - the unique ID for your device should be shown
Tap the WiFi network that you wanted to connect to - check its setting/status for Security, Signal strength, Link speed & IP address
If it previously connected but no longer worked, press "Forget" to delete it, and when it attempt to reconnect (if it is a secured one) - re-enter the password to see if you can connect.
For your restoration purposes, you might want to use WEP or WPA instead of WPA2, or even temporary changed your router to an "Open" WiFi so that any devices including the Vpad7 nearby can connect insecurely, assuming that your router is assigning DHCP automatically and giving out its IP address.
If NONE of these steps are working still, go back into WiFi settings and manually delete any and ALL saved stored networks (named) on the device, leaving just "Add Wi-Fi Network" as the only option.
Next, run a TB backup of your Apps if necessary and boot back into CWM, and do a Backup first to your mSD card (and cover it to a PC if necessary, as you can always restore it back instead of going thru flashing & Set-up) and you will have working boot.img (kernel) saved along with system, etc.
Exit and boot back to ADB (Android) Go to Settings - Privacy setting, and hit "Factory data reset" - next go first into CWM again, wipe dalvik cache & cache again, then continue with regular Setup including WiFi - your device should be able to pickup a nearby & strong WiFi signal.
If all these are still not working, you will likely need to get to a PC or laptop, earlier users had reported having issues with Win7 OS running, I would recommend borrowing/using one with Vista or XP-SP3 running, make sure the USB device drivers are automatically installed first and that it recognize the device. Then, reconnect and run SULT3 and flash the factory *.nb0 file - as I also suspect that there might be other hidden USB device drivers on your existing Win7 system that's casuing the *.nb0 installation to fail.
Keep me posted on your progress and any error messages or crashes (FC) encountered.
(Apparently, some of the custom Roms ended up "corrupting" the WiFi settings and codes, leaving residual settings that casued it to stop connecting to WiFi's - if you look & check some of the posting under "Development" (for some of the Rom's) - you will see some discussions about it. The EUv1.7 custom Rom (non-ITE was initially done and ITE later on) is among the better ones with few WiFi issues to speak of, 15+ months later, still relatively bug-free and updated all the Apps and add-ons of my own from Google Market (Play Store) automatically, with working Flash Player patched, and Angry Birds happily running along - the CPU is slow but with App2SD helping, not too bad for a device running Android 2.2.2 (Froyo)
I checked the settings in the About section and they are identical to the ones you posted.
I left Data enabled however I haven't inserted a SIM card throughout this whole process. I have no data plan anyways with the current SIM card I am going to put in.
Under the advanced settings in Wifi, I changed the sleep policy to Never and the MAC address says "Unavailable". So far there is still no result. I will try connecting in an area where I know there are open networks later today as I live in a public house where I have no access to the router's settings.
Also just a note about cycling Wifi ON and OFF, it automatically turns off after the message "Unable to scan for networks" shows up and no networks actually show up in the Wifi Networks section throughout the whole process. It stays empty even though there are networks around.
There are currently no stored wifi networks either so Add Wi-fi Network is the only option. I recieved this device from someone recently and I completely formatted the mSD card to start fresh so losing any sort of data is no problem to me.
---
I used the backup option in CWM to create another backup and after that I backed up the mSD card through USB to keep the working boot.img and other stuff onto the PC.
Under privacy settings I selected Factory Reset and let the device do its thing. I noticed the intro looked like normal however the Android's "theme" is still like the EUv1.7. I went into CWM and did a dalvik cache wipe along with a cache wipe and reset the device.
I tried the wifi again at this point and still no change.
I also tried SUT L3 with the .nbo and I yeild the same errors as before (0x4000 first time when using from Android screen, 0xC60E after the first time when using SUTL3 without leaving recovery mode).
--
I will test open wifi later today and I will edit the result. I'll also take a look at the discussion on wifi not working around the development forum. Thank you.
---
Edit:
I tested it out on some wifi networks without any protection and still none showed up.
I also noticed that if you right-click the Setup.exe icon in the taskbar after plugging in the Viewpad 7 it gives you the option to uninstall everything that the setup installed. I tried uninstalling and running SUT L3 but there was no difference. Also no difference after reinstalling, just so you know.
clandor said:
I started off by enabling USB debugging and plugging in the tablet.
I opened up SUTL3 v1.7.9 and selected one of the firmwares (both yield same result). The update option I set to Erase user data. Once I hit
Maybe some kind of driver problem?
Click to expand...
Click to collapse
I re-read some of the posts about flashing & restoring factory ROM, and it mentioned turning OFF USB debugging mode (from within the device's Settings - submenu) before -
If you want are ready to give up on this donated/given to you device, you might want to try this as a last resort - then, run SUTL3 with the *.nb0 file to restore it to factory stock condition - and hopefully, get the WiFi working.
From your last description of the error MSG - MAC address unavailable, the settings are definitely corrupted / damaged. Some of the Vpad7 owners had to RMA back to Viewsonic for repairs, obviously it is beyond the warranty and not worth the expense now with this "aging" Froyo OS.
The solution, as you probably read it by now, was to wipe clean & go back to stock, root it again and then try a different custom ROM ...
* * * * * * * * P.S. Please check your PM/in-box for a special message [/B] * * * * * * * *
KWBR V4.2 custom Rom, still available for download, will work with ITE hardware - http://forum.xda-developers.com/showthread.php?t=1386469
Since your CWM is still working, give it a try by flashing and perhaps it can get your WiFi working.
I ended up fixing the problem.
I downloaded PdaNet (PdaNetA350x64.exe) and installed it. I used it to get some drivers for the Viewpad 7 when plugging it in. After that, I replaced the custom recovery menu with an original recovery menu file. Once the recovery was back to normal, I tried running SUT L3 and using the v3_420 .nbo file. It worked fine that time and my device's software was back to default.
--
Afterward, I rooted it and put on a custom recovery menu again. This time I used EUViewpad7 v1.7b ITE version and it did not break my wifi. My original cell phone broke and this device will serve as a pretty good replacement for a little while.
Thanks again for your help, Letitride.
Related
[Q] Root will me wifi, Now: Stuck installing ClockworkMod Recovery to install new ROM
Hello everyone, first of all, I am new on this Android world, so, any basic question I post, I ask for understanding in advance. Trying to root my Viewpad 7 (Froyo 2.2), I come across to GingerBreak, I run it and it sucessfully root but it killed my Wifi (that's all connectivity I used, I have no mobile data plan) as I wanted also to try new rooms, and flash a new one seems to be a only solution for the wifi problem (I have try factory settings without success). I come across Rom manager, I download and install ROM_Manager_Premium_v4.3.2.3.apk from SD and download CleanViewpad7_signed_v1.0.zip to my sd card If I try to flash ClockworkMod Recovery from ROM manager, i get: "Error while downloading from the server. Please make sure you have a stable internet conection ..." but that's no possible as I have no WIFI in my viewPad7 after root! If I try to Install ROM from SD card (from Rom manager), the device restore in "Recovery mode" of "Andoid system recovery <3e>"; and it brakes with message "E:signature verification failed". I have donwload it from several servers (http://forum.xda-developers.com/showthread.php?t=1168562), and all give the same error mesaage I try to search for manual mode to install clockwork (http://forum.xda-developers.com/showthread.php?t=755379) but I can not find a way to go. "wipe data/factory reset" inicializate the device, but it doesn't help with the wifi. it keet saying scaning->disconected->scanning->disconected ... (and of course, my wifi conection is set to remember with the password memorized) In the cofig menu, i can see: baseband: PR3.7_128 Kernel Apps_2.6.32.9 Build 4027_3_16R In the FTM mode: SWver=3.16R Model:FM6-0001 HWVer:106 what can I do?, I just have a 7inch no apps-no connection beautifull "thing"
More: I have try two other Rooms: EUViewpadV1.4.zip Viewpad7 Stock EU 2.2 +rooted+CWM.zip nothing works, signature verification failed
InTheater said: Hello everyone, first of all, I am new on this Android .... Trying to root my Viewpad 7 (Froyo 2.2), I come across to GingerBreak, I run it and it sucessfully root but it killed my Wifi (that's all connectivity I used, I have no mobile data plan) baseband: PR3.7_128 Kernel Apps_2.6.32.9 Build 4027_3_16R SWver=3.16R Model:FM6-0001 HWVer:106 what can I do?, I just have a 7inch no apps-no connection beautifull "thing" Click to expand... Click to collapse Okay, you willl be fine - just need to flash & restore it first to factory/stock ROM first, then root it and go from there - here are the steps that I would suggest: First, save anything important on your mSD card if you need to, perhaps to a USB drive and/or computer's hard drive. Next, use this link http://forum.xda-developers.com/showthread.php?t=1260463 to download - for the stock ROMs from Viewsonic. The newest one is for newer ITE hardware VPAD7 (and, I believe yours is NOT if you could get CleanViewpad v1.0 to boot up & activate the screen - and a number of users are having trouble with wifi ....) To override that signature verification error message that you get, look into CWM (I'm using v3.0.2.8) under Apply update from .zip file on SD card, and there's a "toggle signature verification" switch - change it and trying applying the zip file again to flash - it should work, as I recall. Before that, make sure you wipe system/cache/dalvik & reset data, etc. for a clean(er) new installation. FM6-316Q-*.nb0 should work with earlier, non-ITE Vpad7 and so should FM6-3310-*.nb0, whereas the FM6-3350-*.nb0 should be for newer ITE devices with either HWver 107 and/or (some) HWver 106. To flash it, you CANNOT use CWM but must download the SUTL3 (v1.7.9 worked for me) - read & following the onscreen warnings/directions and it should be finished in less than 10 minutes (have the Vpad7 fully charged first & do NOT need to have the mSD card installed) When it's finished, reinstall the mSD card, take a deep breath & reboot/restart, and you should be up & running with the stock ROM in a few minutes - if so, check your wifi connectivity first before going any further. Start with 316Q ROM first and if it's good, you might want to move up to 3310 next (it's newer) & recheck wifi connectivity. STOP then, as yours is non-ITE and the 3350 will NOT work. You can then flash CWM and/or root it - with SOC or GB methods, etc. etc. which you're familiar with. I had no problems with wifi connectivity and/or 3G data (prepaid GSM 3G coverage) running the Froyo Enhanced custom ROM (non-OC version since I have ITE hardware) OS 2.2 - However, I'm running stock ROM OS 2.2.2 rooted and wifi is perfect for me. (I'm written up a quck tip/guide also - in case you didn't come across it while searching for answers) http://forum.xda-developers.com/showthread.php?t=1264647 Lastly, TJ_Style's FM6 ROM w overclocked kernel should work for you as well, it's OS 2.2 but I patched the boot.img with my saved newer 2.2.2 ITE kernel and got it working too, and, no issues with wifi access at all. In short, check & change your Signature Verification options under CWM and try again, and, if not - restore by reflashing with SUTL3 a factory *.nb0 file, then - proceed from there. Good luck, have a bit of patience - it's both fun & exciting, challenging & disappointment often followed by the joy of luck & success. Let us know how it go & write down any error message(s) so we can help figure it out together - plenty of "newbies" been around but still stranded at times. Regards -
Thanks, SUTL3_v1.7.9 and FM6-3310-0-5029-A02.nb0 works like a charm, easy and bring back my ViewPad7 to work, for anybodies info, that change my ViewPad to: Android version : 2.2.2 (from 2.2) Baseband version PR3.7_128 (same) Kernel Version Apps_2.6.32.9 (same) Build Number 5029_3_310 (from 4027_3_16R) I got encouraged, and I try FM6-3350-0-1008-A01.nb0, that gives me: Android version : 2.2.2 (from 2.2) Baseband version PR3.7_128 (same) Kernel Version Apps_2.6.32.9 (same) Build Number 1008_3_350 (from 4027_3_16R) Swype included !! (seems a little odd and disordered the configuration process, so skip it) what means ITI / non-ITI ? languajes: both nb0 are English/Spanish/French only now I will start with rooting and so, I will let you know once more, many thanks.
Wonderful, we are all glad to know that you had success. Is your wifi working once again with either stock unrooted ROM? Once rooted & CWM reinstalled, do a backup first to save those *.img files, etc. so that you can easily restore/go back later on if necessary. As I said, check out Enhanced Froyo and TJ_Style's FM6 custom ROMs, both of them should work nicely for you - including wifi (I believe, as least on mine - both solid signals in both G and N routers, WEP & WPA-2 modes. (Also, try open or unsecured mode) Happy flashing ....
YES !!, wifi is working back to normal. At least sometimes (I have need to re-flash few time already, it has stoped working few times more, and not becouse of rooting, just installing apps from market) I have also encoutered the next problem : http://www.youtube.com/watch?v=6XuccAxXY_8 and that shouldn't be normal behaviour?, isn't it ? try with diferent room or return to viewsonic ? by the way, what ITE means ? thanks once more
InTheater said: YES !!, wifi is working back to normal. I have also encoutered the next problem : http://www.youtube.com/watch?v=6XuccAxXY_8 and that shouldn't be normal behaviour?, isn't it ? try with diferent room or return to viewsonic ? by the way, what ITE means ? Click to expand... Click to collapse ITE refers to Panjit Touchscreen (Multi-Touch Resistive) used on newer Vpad7 built & shippped vs. older hardwares used on earlier models. On that subject, I've looked at a # of youtube video reviews & posting about the device's orientation/rotation issues, and it seemed to me that it prefer to be in a landscape mode. But, there are times where we wanted to have a choice, turn it 90 degree for a vertical or straight up - not so sure it's 99% hardware problem - rather, problem caused by a mix of Android codes & Apps used. Some were defective but that's a production & quality control issue, so, anyway. I'm not sure after seeing at your YT video what the problem is, please describe & I will have another look with my thoughts on it. Does it happen with the stock/factory ROM or only with the ROM being runned now - I would flash a different ROM to compare the results. Sending it back to Viewsonic is an option but you will be without its use for 2 to 4 weeks (usual timeframe, could be longer) & deal with packing, insuring, shipping & waiting - but, if it's "bad" - get authorization & exchange it or repaired. Regards !
Bad news, as later day, wifi come alive, it went down sometimes, and as I was trying application I flash the three diferent factory rooms few times. What I didn't notice is that the wifo was disconecting more and more often: now it does connect at all. As said, I have try the three diferent ROM in viewsonic, and also an app called FixMyWifi, nothing helps, wife is all the time "Connecting..."->"Disconected"->"Searching"->and so on about the strange behiviour of the screen, the matter is that as soon as using two fingers, the right one, can not be in lower position than the left one. So forgot about plenty of games, drawinf with two fingers, dificulto for rotating maps (when the rotation of finger goes beyond 90 degres) And one of the reasons I bought it is my little boy, explain that to a children of four years..., in deed he found it as "that does work well, the tank does not follow my fingers" so, as a multitouch is basically pointless if you have to care your right finger does not go bellow your left one ... Anything to do with the Wifi ? rooting may help in some way?, and some terminal comands? I am willing to try, I am just in the point before return it as faulty device. Many thanks for all the help given.
InTheater said: What I didn't notice is that the wifo was disconecting more and more often: now it does connect at all .... try the three diferent ROM in viewsonic, and also an app called FixMyWifi, nothing helps and so on .... as a multitouch is basically pointless if you have to care your right finger does not go bellow your left one ... Anything to do with the Wifi ? I am just in the point before return it as faulty device. Click to expand... Click to collapse Thanks for clarifying and I looked at the YT video again - perhaps you would be better off getting Viewsonic for authorization to return for repair or exchange it. On my device, the screen is responsive 98% of the time but I do realize that sometimes, when we're playing Angry Birds, that it too doesn't always readily respond to commands or launch the bird shots .... Not a big deal for games, it will usually get going again - worst case, use the Go Back key & restart the level - I figure that it could be a combination of the Froyo or Android codes written for the OS and/or along with the Angry Birds gaming itself. Afterall, my "regular" & 2 years old smartphone, HTC Eris running a nearly identical CPU & configuration is running custom rooted GingerBread ROM - and, is must better & responsive in overclocked mode. The Vpad7 will not, I feel, be running Honeycomb but let's hope that some of the veteran xda developers will soon release a working GingerBread ROM - perhaps it will fix many of the issues across the field, so to speak. (or, if Viewsonic will release it as official update .... wishful thinking, huh - but !) On the wifi issues, have you tried doing the SuperOneClick and/or GingerBreak apk to root, and then flash TJ_Style's custom FM6 ROM - http://forum.xda-developers.com/showthread.php?t=1264647 - this OC version with WiFi fix might work for you without any mods (patching or zip flashing the 2.2.2 boot.img) On wifi configuration itself, is this happening with different routers - "older" G mode or newer N (faster) routers, unsecured or open network or secured (WEP, WPA or WPA2, etc.) - any issues on the host computer/router's firewall blocking ? Can you log in at a public hotspot or cafe like Starbuck ? Go into Settings > Wireless & network settings > Wi-Fi settings > and, then, tap the Home key (the bottom of 4 keys on the device - held in landscape mode) and you should see "Scan" & "Advanced" - does it pickup a decent signal ? Click "Advanced" & look at your "Wi-Fi sleep policy" - mine is checked for "When screen turn off" - tried "Never" or "Never when plugged in" - any difference ? If you get this far, you might want to try to set up & Use "static IP" instead of using dynamic ip addressing that these devices usually count on .... it's a bit of work, but might help to "zoom" into your own router only. I use "Wifi Analyzer" v2.5.13 from Kevin Yuan (Google Market) to help scan the spectrum for signals and possible interference, which sometimes do happen - and moved 1 of our 2 cable broadband router to a different channel so that all of our wireless (up to 15 of them, yes) devices around the house can easily connect to the hotspots. (Reading posts @ other forum sites & ran my inSSIDer v2.0 from Dell laptop for baseline, it scanned 17 active APN's with varying signal strengths, our Sony W995 picked up only 6 signals with 3 good ones, the HTC Eris picked up 6 signals also with 3 good ones, and the Vpad7 only 3 signals, 2 of them from our own indoor G & N routers plus 1 from neighbors that's marginal. It's safe to assume that our device's internal radio receiver or Baseband isn't very good with reception to begin with - you might need to flash a different "build" like mine to give it a try - and try switching your wifi channel.) Just some of my thoughts on the wifi problem as I do run into signal problems myself every so often installing a new device or configure a guest's new gadget at home. If all else failed and along with the touchscreen problem, then I would say get it fixed via repair or exchange from Viewsonic, and then .... (a few weeks later, upon its return to you - happy rooting & flashing, etc.)
Letitride said: Thanks for clarifying and I looked at the YT video again - perhaps you would be better off getting Viewsonic for authorization to return for repair or exchange it. On my device, the screen is responsive 98% of the time but I do realize that sometimes, when we're playing Angry Birds, that it too doesn't always readily respond to commands or launch the bird shots .... Not a big deal for games, it will usually get going again - worst case, use the Go Back key & restart the level - I figure that it could be a combination of the Froyo or Android codes written for the OS and/or along with the Angry Birds gaming itself. Click to expand... Click to collapse Thanks a lot, that I have done, and ask ViewSonic for replacement, I hope they return me one fully working (by the way, sorry for so late response, I have been for 2 weeks out) Letitride said: Afterall, my "regular" & 2 years old smartphone, HTC Eris running a nearly identical CPU & configuration is running custom rooted GingerBread ROM - and, is must better & responsive in overclocked mode. The Vpad7 will not, I feel, be running Honeycomb but let's hope that some of the veteran xda developers will soon release a working GingerBread ROM - perhaps it will fix many of the issues across the field, so to speak. (or, if Viewsonic will release it as official update .... wishful thinking, huh - but !) Click to expand... Click to collapse yes, it seems that the viewsonc doen't have so good hardware after all ... Letitride said: On the wifi issues, have you tried doing the SuperOneClick and/or GingerBreak apk to root, and then flash TJ_Style's custom FM6 ROM - http://forum.xda-developers.com/showthread.php?t=1264647 - this OC version with WiFi fix might work for you without any mods (patching or zip flashing the 2.2.2 boot.img) On wifi configuration itself, is this happening with different routers - "older" G mode or newer N (faster) routers, unsecured or open network or secured (WEP, WPA or WPA2, etc.) - any issues on the host computer/router's firewall blocking ? Can you log in at a public hotspot or cafe like Starbuck ? Go into Settings > Wireless & network settings > Wi-Fi settings > and, then, tap the Home key (the bottom of 4 keys on the device - held in landscape mode) and you should see "Scan" & "Advanced" - does it pickup a decent signal ? Click "Advanced" & look at your "Wi-Fi sleep policy" - mine is checked for "When screen turn off" - tried "Never" or "Never when plugged in" - any difference ? If you get this far, you might want to try to set up & Use "static IP" instead of using dynamic ip addressing that these devices usually count on .... it's a bit of work, but might help to "zoom" into your own router only. Click to expand... Click to collapse about the wifi issue, I have try all the steps you mention before, nothing helps with my router (deliver by the telephone company). The only thing that works, sometimes, s turning off the router for several seconds, then it connect again. As absurd it sounds, it looks like the viewpad doesn't disconnect from the router even as turned off, so the router doesn't allow to negociated again a conection (and it keeps it in connected device while the viewpad is reseting or turned off) I have try connecting a Linksys Wi-fi and connecting trought it : WORKS GREAT. Trying in different locations, some of them same problem as the router, others works perfectly. Solved for home with second wifi-point, I see myself one day asking Starbuchs guy to reset their router... Letitride said: I use "Wifi Analyzer" v2.5.13 from Kevin Yuan (Google Market) to help scan the spectrum for signals and possible interference, which sometimes do happen - and moved 1 of our 2 cable broadband router to a different channel so that all of our wireless (up to 15 of them, yes) devices around the house can easily connect to the hotspots. (Reading posts @ other forum sites & ran my inSSIDer v2.0 from Dell laptop for baseline, it scanned 17 active APN's with varying signal strengths, our Sony W995 picked up only 6 signals with 3 good ones, the HTC Eris picked up 6 signals also with 3 good ones, and the Vpad7 only 3 signals, 2 of them from our own indoor G & N routers plus 1 from neighbors that's marginal. It's safe to assume that our device's internal radio receiver or Baseband isn't very good with reception to begin with - you might need to flash a different "build" like mine to give it a try - and try switching your wifi channel.) Just some of my thoughts on the wifi problem as I do run into signal problems myself every so often installing a new device or configure a guest's new gadget at home. If all else failed and along with the touchscreen problem, then I would say get it fixed via repair or exchange from Viewsonic, and then .... (a few weeks later, upon its return to you - happy rooting & flashing, etc.) Click to expand... Click to collapse so, waiting for Viewsonic to replace my viewpad, I will inform as I have a new one in hands. thanks a lot !!
can someone plz help me i am trying to flash this viewpad7 i get this error error code:0x4000 error:task 2 of 3,download image fail, error:device_not_configure (0x4000) can you plz help me thanks
To see this address http://forum.xda-developers.com/showthread.php?t=1433052 Good luck Hussein
What to do if your Wifi/Bluetooth fails causing reboots
Here is an attempt to provide a definitive answer to what to do if your phone has the Bluetooth/Wifi hardware failure. Note that some of the links don't seem to work with the xda-developer app or the Atrix built in browser. Please blame motorola, not me Symptoms: 1) If your phone was set to try to use Wifi by default on boot: Your phone boots into the OS but shortly afterwards freezes and reboots - and again and again. 2) If your phone boots with Wifi turned off: Your phone boots into the OS and a few seconds after you enable the Wifi in settings or via a widget it shows "Error" and sometimes the phone reboots shortly afterwards. Bluetooth simply fails to work. If you have warranty return it for a repair. If not the best you can get is to disable the Wifi and Bluetooth so the phone doesn't reboot and can be used with mobile data. Instructions for both are below: Be sure it is the Bluetooth / Wifi hardware failure: 1) Are you running a custom ROM? - if yes go to 1.1, if no goto 2. 1.1) Reboot into recovery and make a backup. 1.2) Remove your SD card. 1.3) Reflash using RSD to stock - remember to get the right one for the right country! Get RSD and drivers here: http://forum.xda-developers.com/showthread.php?t=1136261 Search for your stock firmware using google Use RSD to install the stock firmware file which will replace the bootloader, recovery and radio - takes about 20 minutes. Goto 2. 2) Reboot into Stock Android Recovery and reset to factory defaults https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/60620 2.1) Reboot to Android and try enabling wifi from settings - if it reports "Error" after a few seconds and your phone may reboot shortly afterwards it is the hardware fault. Proceed to 3. 3) Check your remaining warranty here: https://motorola-global-portal.custhelp.com/app/answers/prod_answer_detail/a_id/82507/p/30,6720,7898 Bottom left - enter your IMEI. Warranty left goto 3.1 else goto 4. 3.1) Return to Motorola for repair - be sure you flashed back to stock first using instructions in 1.3 4) Unpalatable options are all that is left. Either pay or do without Wi-Fi and Bluetooth. Have money and the desire to fix your Atrix ($110 in the USA)? Goto 4.1 else 5 4.1) Consider paying Motorola to repair the phone anyway. Schedule a repair here https://motorola-global-portal.custhelp.com/app/answers/prod_answer_detail/a_id/82507/p/30,6720,7898 5) This is a complex process. Google is your friend. Unlock your phone using the instructions below. Note you have no warranty to lose (see 3)! http://forum.xda-developers.com/showthread.php?t=1136261 5.1) Install romracers CWM custom recovery using moto-fastboot (or Android fastboot): http://forum.xda-developers.com/showthread.php?t=1204500 5.2) Did you take a backup earlier? If yes go to 5.3. If no goto 6. 5.3) Reboot into CWM recovery and restore your backup. Note if you are stuck in a bootloop this will be ok in a bit. Goto 7. 6) Install your favourite ROM using CWM recovery from a SDCARD or by moto-fastboot. Goto 7. 7) Reboot into CWM recovery 7.1) Plug your phone into your PC (you might have to wait for the driver to enumerate the phone first) 7.2) Find or install adb on your computer (hint - it comes with the Android SDK and platform tools from earlier): adb shell mount /system cd /system/lib/modules mv dhd.ko dhd.ko2 reboot 8) When you install a new ROM or kernel goto 7. Every time. This little setup moves the driver linux needs to try to talk to the wifi/bluetooth chip which has failed so it can't find it. If it can't find it then it doesn't try to talk to the dead Broadcom Bluetooth Wifi chip that prevents the reboot cycle happening. The fix was pioneered by: mvniekerk http://forum.xda-developers.com/member.php?u=2353874 So go thank him! In the hopes this helps, Matthew
Good job. Well said.
Considering how many posts I have seen after posting this solution perhaps it could be sticky? I promise to maintain it. Matthew Sent from my MB860 using xda app-developers app
Hmmm I think I have done that correctly and flashed the 2.8 Neutrino GT. There was no reboot up to now. But I want to ask if there is a fix for WIFI 'ERROR' and BLUETOOTH error without 'ERROR' message? Guys please. I can try anything I don't want to lose my phone Warranty is over. How can I find the Broadcom BCM4329 wireless and bluetooth chipset for atrix? So I can find a technician to change it with mine.
If you have the failure there isn't much to be done. Ifixit has a teardown but the chip is a very small ball grid type thing which will be very hard to fix. What are your symptoms precisely? Sent from my MB860 using xda app-developers app
mattaw2001 said: If you have the failure there isn't much to be done. Ifixit has a teardown but the chip is a very small ball grid type thing which will be very hard to fix. What are your symptoms precisely? Sent from my MB860 using xda app-developers app Click to expand... Click to collapse When I click on 'Turn on Wifi' button, It says 'Turning on Wifi' for 10 seconds and then 'Error' message comes up under the Wifi button and when I click on 'turn on bluetooth' it says 'turning on' but does not turn on. Same as wifi but without the 'error' message. How can I fix this? I can't use wifi and bluetooth!
Nothing to be done. There is some discussion as to why but a chip in your phone made by broadcom which handles both wifi and Bluetooth has failed. Short of replacing it requiring sophisticated soldering tools you are stuck. See the $110 Motorola warranty repair. Sorry, Matthew Sent from my MB860 using xda app-developers app
Im stuck. I have applied the fix to NottachTrix4G rom. I still have the random reboots. I really need help.
Do you get the wifi error message or not? Secondly does this happen with the normal, stock Motorola rom? Matthew Sent from my MB860 using xda app-developers app
When i check wifi does show error. I have not tried the stock moto rom yet.
The best thing to do is return to stock and do a factory reset Carry out a full backup first (nandroid or using CWM recovery). The best thing to do is return the atrix to stock and then do a factory rest. If the problem persists then it is a hardware problem and you can now return it under warranty without them knowing (see the thread for instructions). Otherwise you seem rather stuck. Perhaps buy an atrix with a smashed screen and transfer the motherboard? Matthew
Noattachtrix rom was good, but not good enough. little_man_3666 said: I have applied the fix to NottachTrix4G rom. I still have the random reboots. I really need help. Click to expand... Click to collapse I ended up using RomGb instead and that fix the bootloop after using NottachTrix4G Rom.
This happened to me Saturday November 17, 2012. Rebooting did not help. Did my searches and found this thread - and was bummed to read that it is due to a hardware issue. Fortunately, I persisted. With the WiFi widget endlessly spinning, I tried the Bluetooth, which would just fail and go to an off state. I elected to do a force close on any running applications one by one, testing Bluetooth after each. I found that BlueTooth and WiFi functionality would come back after force closing some apps. I stupidly left WiFi on and rebooted the phone - this put me in an endless reboot cycle. In the midst of one I managed to enable car dock mode which I have configured to disable WiFi and this got me out of the loop. I found my issue, which has the same symptoms as the above, was caused by a recent update to WeatherBug Elite. I uninstalled the program, and am back to normal operation. Hope this helps others. Update - it appears my problems continue. Although I can now access BT & WiFi, the problem will re-occur. Force closing Weather version 2.2.2 usually will clear the issue, but I have had a good working WiFi sessions halt to Error. Still gotta think it's software rather than hardware.
Thanks I thought it was the ROM until I found this thread
Well, I was wrong. The issue is hardware not software. In my case pressing the volume down button would change the behavior sometimes, like get bluetooth to work, press volume down it stops or vice versa. Time for a replacement.
I mount the system successfully but when I type cd /system/lib/modules I get it cant find the directory, Please help. I need to do this to stop reboot!!
Definitely Software I have atrix 4g. Running MROM 2013 2 13. I have the error on WIFI and NO Bluetooth. No reboot, but I rarely use the wifi enough to leave it on(conserve the batt). This is a software issue as far as I can tell as well.. I can fix it by killing the mrom service in "manage applications". If I get a chance I will look further but this seems like enough of a fix to not care.. MROM is pretty great besides this issue.(which appears to happen on multiple roms. My guess would be that it started with CM, but only because that is what the roms are based off of that get the problem.
bubba1993 said: I mount the system successfully but when I type cd /system/lib/modules I get it cant find the directory, Please help. I need to do this to stop reboot!! Click to expand... Click to collapse Having the same issue. Wifi died after the phone fell off my hands. I had the CM10 ROM by ephinter and everything worked great except the wifi (no reboots). Then I had the AMAZING idea of installing a new ROM and the reboot loop started. EIther with any stock or custom ROM it continues to happen. Tried everything without success. Have anyone tried disabling wifi in the settings.sqlite and see what happens?
jaunis I found out why mine was doing the boot loop and it is funny but very weird. I wiped the phone and put my cm7 back on there and forgot to activate my gmail account or any account for that case. Now I have been running it with no problems for 40 hours. But of course still no wifi. I am fine with that. but at least I am not dealing with the reboots.
I have an unlocked AT&T Atrix 4G with a custom ROM (Cyan 9.x & ICS 4.x). I started having WiFi issues where the device would reboot anytime I tried to enable the WiFi. This all started at least 6mo after installing the custom rom so I dont think its software related. To try and fix the issue I tried doing a data wipe factory reset, at this point I couldn't get past the welcome screen because WiFi didn't work and I dont have a SIM in the phone (my kid has been using it for games). So from here I decided to try and flash the phone back to stock using RSD Lite; Be sure it is the Bluetooth / Wifi hardware failure: 1) Are you running a custom ROM? - if yes go to 1.1, if no goto 2. 1.1) Reboot into recovery and make a backup. 1.2) Remove your SD card. 1.3) Reflash using RSD to stock - remember to get the right one for the right country! Get RSD and drivers here: http://forum.xda-developers.com/showthread.php?t=1136261 Search for your stock firmware using google Use RSD to install the stock firmware file which will replace the bootloader, recovery and radio - takes about 20 minutes. Goto 2. 2) Reboot into Stock Android Recovery and reset to factory defaults https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/60620 Click to expand... Click to collapse I downloaded the AT&T 2.3.4 / 4.5.91 Service SBF which looks like this in RSDLite: 1ff-olympus-user-2.3.4-4.5.91-110625-release-keys-signed-att-us-gas_na_olpsgbattspe_p011.sbf I started the flash and left my phone for 15m or so to do its thing. When I came back my phone was boot looping (shown in a video here: http://youtu.be/V9wtBNEWRPQ ). I can't do a factory reset from Stock Android Recovery (step 2 above), I can't get the menu for it. Now what do I do? Did I grab the wrong SBF file? Currently the only place I can grab SBF files at is here: http://www.das8nt.com/sbffiles.html
[Q] Failed update, cannot run applications
Before Christmas I tried to do a OTA update on my Prime, which has not been successful and I have not been able to use the Prime since. It has previously been rooted and previously have always been successful in using Voodoo OTA Rootkeeper to retain root after updates. I've not unlocked the Prime. Now when I try to boot it spends a while 'optimizing' the applications (as if it was the first time i've booted it since the update), and then once it is started, no apps will startup, all of them resulting in saying "unfortunately xyz has stopped" A video of the problem: youtu.be/e1yfTtGiR78 (sorry can't post full link as am a new user). I'd like to get it working again, possibly installing the Androwook ROM (or at the very least, just working on the stock rom). What steps do I need to do from where I am at the moment? There are many threads about flashing roms, brick-fixing (some more up to date than others), but I'd just like a bit of advice about this problem and what I should do next (maybe some good links?). I haven’t gone near doing any flashing on the Prime, and it would be nice to seperate the things I could do, from the things I -should- do (I don't know where to start). I believe as the Nvidida logo is on the bottom right this means I'm on the JB bootloader? Currently the settings menu shows I'm on android 4.1.1, but not sure if this is pre or post the failed update. Thanks for any help, Steve
A factory reset will fix you up. You'll lose your data Hold vol down + power when booting to access the boatloader menu. Select wipe with vol down and use vol up to confirm.
Hi, Thanks, I've done the reset, but I still seem to have the same problem. imageshack.us/photo/my-images/502/imag0217c.jpg I can't actually proceed throuh the inital set up, because it closes itself when it gets to the account setup page. Any ideas?
I have resolved this. I downloaded the latest firmware from the ASUS support website, extracted the zip file from within the downloaded zip file and renamed it to EP201_SDUPDATE.ZIP . Put this on a microSD card (which I had formatted to FAT32), inserted it into the Prime, then booted into the bootloader menu. Selected the RCK option, it did the update, and 10 minutes later it was up and running again. From what I have read, it won't try to complete the update if it thinks you have already got that version installed already, but I guess it knew it hadn't successfully completed the update previously. Glad it's working again.
[Q] [Fixed] MTK6589 - Flashtool readback killed BT/Wifi/GPS
Hello, I've bought a new device - Evolveo StronPhone Q4, MTK6589 based phone. The stock ROM is basically vanilla Android 4.2.1. I've successfully rooted it using Framaroot. Then I've created scatter file using MTK Droid Tools (all partitions that were formated were ext4). Then I've decided to create a backup before I start playing with it, so I've tried backing up flash using SP Flash Tool (using Readback), it was running fine and downloaded approx. 20%, then crashed. I've tried that once or twice more times, always failed. Now after I plug it in, windows display "This device can perform faster" and FlashTool won't detect the device. If I connect it without battery with VolDn key pressed, FlashTool detects it and I get S_DL_GET_DRAM_SETTING_FAIL. However, the phone boots fine, just GPS/Wifi/BT is not working. (No GPS icon appers, and I get errors like BT_open: WMT turn on BT fail in dmesg). Looks like an issue with kernel/HW issue. Any ideas what could have gone wrong and how to fix it? In the meantime, I've asked manufacturer for a stock FW image, but I'm not sure it helps... Update: Okay, I have no clue what just happened. However I've unrooted, reverted everything I've modified on the phone so far so I'll be able to return it to manufacturer as "deffective"... And just for the curiosity connected it to the computer and tried downloading ROM one more time. And it succeeded - I'll upload the ROM once I get access to faster internet connection. I've removed the battery (phone was stuck in Preloader mode because I cancelled ongoing RAM test.), put it back and now everything works. So, it looks like everything is fine now, however I'd love to know what happened, if you have any clue, please let me know!
fw problem Mrkvak said: Hello, I've bought a new device - Evolveo StronPhone Q4, MTK6589 based phone. The stock ROM is basically vanilla Android 4.2.1. I've successfully rooted it using Framaroot. Then I've created scatter file using MTK Droid Tools (all partitions that were formated were ext4). Then I've decided to create a backup before I start playing with it, so I've tried backing up flash using SP Flash Tool (using Readback), it was running fine and downloaded approx. 20%, then crashed. I've tried that once or twice more times, always failed. Now after I plug it in, windows display "This device can perform faster" and FlashTool won't detect the device. If I connect it without battery with VolDn key pressed, FlashTool detects it and I get S_DL_GET_DRAM_SETTING_FAIL. However, the phone boots fine, just GPS/Wifi/BT is not working. (No GPS icon appers, and I get errors like BT_open: WMT turn on BT fail in dmesg). Looks like an issue with kernel/HW issue. Any ideas what could have gone wrong and how to fix it? In the meantime, I've asked manufacturer for a stock FW image, but I'm not sure it helps... Update: Okay, I have no clue what just happened. However I've unrooted, reverted everything I've modified on the phone so far so I'll be able to return it to manufacturer as "deffective"... And just for the curiosity connected it to the computer and tried downloading ROM one more time. And it succeeded - I'll upload the ROM once I get access to faster internet connection. I've removed the battery (phone was stuck in Preloader mode because I cancelled ongoing RAM test.), put it back and now everything works. So, it looks like everything is fine now, however I'd love to know what happened, if you have any clue, please let me know! Click to expand... Click to collapse hello, could you please upload somewhere original fw for Evolveo Strongphone Q4. im in bootloop now
Hi all, can you hel me with strongphone Q4, do you know any better rom for this phone? Maybe by PM in czech? ...
Possible to recover or extract user data from my A10?
Long story short....eh.....?!! My Samsung Galaxy A10 (SM-A105FN) got wet during a rainy bikeride! At first it still worked - but then started to show a yellow triangle with exclamation point (charging problem?), restarting and ending up in Android Recovery (the one with only three options - Try again, Factory data reset and View recovery logs) saying Can't load Android system, Reboot Recovery Cause is: Unable to disable quotas on dev/block/platform because system/bin/tune2fs is missing. So, not able to get into system and turn on USB debugging etc... Current stock firmware PDA: A105FNXXU6BUC3 (Android 10) Tried to install new firmware via Apply update from ADB and SD card but both failed saying Failed: Out of memory. With Odin I got PASS! flashing BL+AP+CP+HOME_CSC with latest stock fimware PDA: A105FNXXS7CVB1 (Android 11) - but still in Recovery loop now saying Reboot Recovery Cause is: [set_policy_failed / data/app] The phone is not rooted nor bootloader unlocked. I don't care about the phone (budget) - but I really do need my own data back!! Is there a way without losing data? TWRP?? Jan
In trying to be helpful, all I can do is point you to this thread where I personally organized in one place over 200 similar threads (almost) exactly like yours (where all had an unresponsive screen - but most were due to being dropped). What is the best XDA solution to control Android on the PC & recover data over Wi-Fi when the user suddenly has an unresponsive broken screen?
GalaxyA325G said: In trying to be helpful, all I can do is point you to this thread where I personally organized in one place over 200 similar threads (almost) exactly like yours (where all had an unresponsive screen - but most were due to being dropped). What is the best XDA solution to control Android on the PC & recover data over Wi-Fi when the user suddenly has an unresponsive broken screen? Click to expand... Click to collapse Thanks GalaxyA325G! I'll dig into that thread!! Probably - or, definitely - I'm screwed....!!!
also TWRP supports MTP