Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!
Hey guys, does anyone have any experience to share on changing the power button? Mine is flushed down and and it doesn't click. I saw the flex cable on sale on Aliexpress, do you know how easy/hard it is to repair (starting from the back cover removal...)?
Very easy. 10 to 15 minutes.
could you share the links and take pictures or video of the process when you do it?
Mine is already tilting a lot up and down. thanks!
https://www.youtube.com/watch?v=no0xV89CPMs&list=WL&t=132s&index=29
I think this is the most comprehensive video of p9000's disassembly
I've just replaced one and it's very easy.
Take back off, unscrew the top plastic cover to access the ribbon cable, remembering to unscrew the single screw with a sticker on it. The buttons just slide in and the ribbon cable clips in as usual.
check this video! https://www.youtube.com/watch?v=_Us9A-Il0AY&index=69&list=WL